Home
last modified time | relevance | path

Searched refs:HIGH (Results 1 – 25 of 58) sorted by relevance

123

/linux/arch/arm64/boot/dts/rockchip/
H A Drk3588-jaguar-pre-ict-tester.dtso81 * LOW. The signal shall not read HIGH in the event
89 * rail. It should be HIGH if all is properly soldered.
108 * soldering issue on GPIO3_B2 reports HIGH but proper
114 * rail. It should be HIGH if all is properly soldered.
117 * GPIO3_C6 default bias is pull-up therefore being HIGH
119 * - GPIO3_C6 is floating (so HIGH) if GPIO3_C6 is not
121 * - GPIO3_C6 is floating (so HIGH) if VCC_1V8_S0_1 is
123 * - GPIO3_C6 is HIGH if everything is proper,
126 * soldering reports HIGH.
132 * It should be HIGH i
[all...]
H A Drk3368-evb.dtsi225 rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
H A Drk3368-r88.dts319 rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
/linux/Documentation/devicetree/bindings/media/i2c/
H A Dovti,ov7670.txt13 - hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
14 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
H A Dti,tvp5150.txt44 - hsync-active: Active state of the HSYNC signal. Must be <1> (HIGH).
45 - vsync-active: Active state of the VSYNC signal. Must be <1> (HIGH).
/linux/arch/arm64/boot/dts/renesas/
H A Dhihope-rzg2-ex-lvds.dtsi21 * When GP1_20 is HIGH LVDS0 is connected to the LT8918L
/linux/include/linux/mfd/
H A Dtps65010.h124 #define HIGH 1 macro
141 * value: LOW or HIGH
/linux/arch/arm/boot/dts/rockchip/
H A Drk3228-evb.dts67 rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
H A Drk3288-rock2-som.dtsi251 rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
H A Drk3288-evb.dtsi301 rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
/linux/drivers/s390/crypto/
H A Dzcrypt_msgtype6.h108 #define HIGH 500 macro
/linux/drivers/tty/vt/
H A Ducs_width_table.h_shipped25 { 0x06D6, 0x06DD }, /* ARABIC SMALL HIGH LIGATURE SAD WITH LAM WITH ALEF MAKSURA - ARABIC END OF AYAH */
26 { 0x06DF, 0x06E4 }, /* ARABIC SMALL HIGH ROUNDED ZERO - ARABIC SMALL HIGH MADDA */
27 { 0x06E7, 0x06E8 }, /* ARABIC SMALL HIGH YEH - ARABIC SMALL HIGH NOON */
33 { 0x07EB, 0x07F3 }, /* NKO COMBINING SHORT HIGH TONE - NKO COMBINING DOUBLE DOT ABOVE */
42 { 0x08CA, 0x0903 }, /* ARABIC SMALL HIGH FARSI YEH - DEVANAGARI SIGN VISARGA */
315 { 0x16AF0, 0x16AF4 }, /* BASSA VAH COMBINING HIGH TONE - BASSA VAH COMBINING HIGH-LOW TONE */
372 { 0x26A1, 0x26A1 }, /* HIGH VOLTAG
[all...]
/linux/Documentation/userspace-api/media/cec/
H A Dcec-ioc-dqevent.rst160 * .. _`CEC-EVENT-PIN-CEC-HIGH`:
176 * .. _`CEC-EVENT-PIN-HPD-HIGH`:
194 * .. _`CEC-EVENT-PIN-5V-HIGH`:
/linux/Documentation/devicetree/bindings/mfd/
H A Dmax77620.txt122 GPIO1/nRST_IO pins are HIGH only if all rails
123 that have POK control enabled are HIGH.
H A Dtps6507x.txt30 1: If defdcdc pin of DCDC2/DCDC3 is driven HIGH.
/linux/arch/arm/boot/dts/nxp/imx/
H A Dimx6q-bosch-acc.dts441 connect-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; /* Old: 0, SS: HIGH */
442 intn-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; /* Old: 1, SS: HIGH */
443 reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; /* Old: 0, SS: HIGH */
/linux/drivers/nfc/st95hf/
H A Dcore.c75 #define HIGH 1 macro
453 gpiod_set_value(st95con->enable_gpiod, HIGH); in st95hf_send_st95enable_negativepulse()
465 gpiod_set_value(st95con->enable_gpiod, HIGH); in st95hf_send_st95enable_negativepulse()
/linux/arch/arm/mach-omap1/
H A Dboard-osk.c214 /* Set GPIO 1 HIGH to disable VBUS power supply; in osk_tps_setup()
223 tps65010_set_gpio_out_value(GPIO2, HIGH); in osk_tps_setup()
/linux/Documentation/iio/
H A Dad7191.rst68 - When CLKSEL pin is tied HIGH: Requires external clock source
/linux/Documentation/leds/
H A Dleds-lm3556.rst24 or by pulling the STROBE pin HIGH.
/linux/include/trace/events/
H A Dmmflags.h23 TRACE_GFP_EM(HIGH) \
/linux/Documentation/devicetree/bindings/pinctrl/
H A Dpinctrl-max77620.txt66 master FPS input event set to HIGH.
/linux/Documentation/driver-api/iio/
H A Dbuffers.rst62 |D11|D10|D9 |D8 |D7 |D6 |D5 |D4 | (HIGH byte, address 0x07)
/linux/tools/power/cpupower/bench/
H A DREADME-BENCH114 -p, --prio=<priority> scheduler priority, HIGH, LOW or DEFAULT
/linux/Documentation/wmi/devices/
H A Dalienware-wmi.rst247 | 0 | Device Firmware Update (DFU) | **HIGH**: Enables DFU mode |
253 | 1 | Negative Reset (NRST) pin. | **HIGH**: MCU is ON. |

123