1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * drivers/net/phy/qsemi.c
4 *
5 * Driver for Quality Semiconductor PHYs
6 *
7 * Author: Andy Fleming
8 *
9 * Copyright (c) 2004 Freescale Semiconductor, Inc.
10 */
11 #include <linux/kernel.h>
12 #include <linux/string.h>
13 #include <linux/errno.h>
14 #include <linux/unistd.h>
15 #include <linux/interrupt.h>
16 #include <linux/init.h>
17 #include <linux/delay.h>
18 #include <linux/netdevice.h>
19 #include <linux/etherdevice.h>
20 #include <linux/skbuff.h>
21 #include <linux/spinlock.h>
22 #include <linux/mm.h>
23 #include <linux/module.h>
24 #include <linux/mii.h>
25 #include <linux/ethtool.h>
26 #include <linux/phy.h>
27
28 #include <asm/io.h>
29 #include <asm/irq.h>
30 #include <linux/uaccess.h>
31
32 /* ------------------------------------------------------------------------- */
33 /* The Quality Semiconductor QS6612 is used on the RPX CLLF */
34
35 /* register definitions */
36
37 #define MII_QS6612_MCR 17 /* Mode Control Register */
38 #define MII_QS6612_FTR 27 /* Factory Test Register */
39 #define MII_QS6612_MCO 28 /* Misc. Control Register */
40 #define MII_QS6612_ISR 29 /* Interrupt Source Register */
41 #define MII_QS6612_IMR 30 /* Interrupt Mask Register */
42 #define MII_QS6612_IMR_INIT 0x003a
43 #define MII_QS6612_PCR 31 /* 100BaseTx PHY Control Reg. */
44
45 #define QS6612_PCR_AN_COMPLETE 0x1000
46 #define QS6612_PCR_RLBEN 0x0200
47 #define QS6612_PCR_DCREN 0x0100
48 #define QS6612_PCR_4B5BEN 0x0040
49 #define QS6612_PCR_TX_ISOLATE 0x0020
50 #define QS6612_PCR_MLT3_DIS 0x0002
51 #define QS6612_PCR_SCRM_DESCRM 0x0001
52
53 MODULE_DESCRIPTION("Quality Semiconductor PHY driver");
54 MODULE_AUTHOR("Andy Fleming");
55 MODULE_LICENSE("GPL");
56
57 /* Returns 0, unless there's a write error */
qs6612_config_init(struct phy_device * phydev)58 static int qs6612_config_init(struct phy_device *phydev)
59 {
60 /* The PHY powers up isolated on the RPX,
61 * so send a command to allow operation.
62 * XXX - My docs indicate this should be 0x0940
63 * ...or something. The current value sets three
64 * reserved bits, bit 11, which specifies it should be
65 * set to one, bit 10, which specifies it should be set
66 * to 0, and bit 7, which doesn't specify. However, my
67 * docs are preliminary, and I will leave it like this
68 * until someone more knowledgable corrects me or it.
69 * -- Andy Fleming
70 */
71 return phy_write(phydev, MII_QS6612_PCR, 0x0dc0);
72 }
73
qs6612_ack_interrupt(struct phy_device * phydev)74 static int qs6612_ack_interrupt(struct phy_device *phydev)
75 {
76 int err;
77
78 err = phy_read(phydev, MII_QS6612_ISR);
79
80 if (err < 0)
81 return err;
82
83 err = phy_read(phydev, MII_BMSR);
84
85 if (err < 0)
86 return err;
87
88 err = phy_read(phydev, MII_EXPANSION);
89
90 if (err < 0)
91 return err;
92
93 return 0;
94 }
95
qs6612_config_intr(struct phy_device * phydev)96 static int qs6612_config_intr(struct phy_device *phydev)
97 {
98 int err;
99 if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
100 err = phy_write(phydev, MII_QS6612_IMR,
101 MII_QS6612_IMR_INIT);
102 else
103 err = phy_write(phydev, MII_QS6612_IMR, 0);
104
105 return err;
106
107 }
108
109 static struct phy_driver qs6612_driver[] = { {
110 .phy_id = 0x00181440,
111 .name = "QS6612",
112 .phy_id_mask = 0xfffffff0,
113 /* PHY_BASIC_FEATURES */
114 .config_init = qs6612_config_init,
115 .ack_interrupt = qs6612_ack_interrupt,
116 .config_intr = qs6612_config_intr,
117 } };
118
119 module_phy_driver(qs6612_driver);
120
121 static struct mdio_device_id __maybe_unused qs6612_tbl[] = {
122 { 0x00181440, 0xfffffff0 },
123 { }
124 };
125
126 MODULE_DEVICE_TABLE(mdio, qs6612_tbl);
127