| /linux/drivers/net/dsa/mv88e6xxx/ |
| H A D | leds.c | 100 bool fiber; member
153 .fiber = true,
161 .fiber = true,
183 .fiber = true,
191 .fiber = true,
211 .fiber = true,
338 bool fiber, unsigned long rules, u16 *selector) in mv88e6xxx_led_match_selector() argument
368 if (conf->fiber != fiber) in mv88e6xxx_led_match_selector()
426 bool fiber, unsigned long rules, u16 *selector) in mv88e6xxx_led_get_selector() argument
435 err = mv88e6xxx_led_match_selector(p, led, false, fiber, rules, selector); in mv88e6xxx_led_get_selector()
[all …]
|
| H A D | chip.h | 298 bool fiber; member
|
| H A D | chip.c | 3389 p->fiber = fwnode_property_present(port_fwnode, "sfp"); in mv88e6xxx_setup_port()
|
| /linux/drivers/net/fddi/ |
| H A D | Kconfig | 12 run over copper or fiber. If you are connected to such a network and
23 This is support for the DEC FDDIcontroller 700 (DEFZA-AA, fiber)
|
| /linux/drivers/net/ethernet/alacritech/ |
| H A D | Kconfig | 24 both copper and fiber.
|
| /linux/drivers/net/dsa/microchip/ |
| H A D | ksz8.c | 1166 if (dev->ports[port].fiber) in ksz8_w_phy_bmcr()
1742 p->fiber = 1; in ksz8_config_cpu_port()
1744 if (p->fiber) in ksz8_config_cpu_port()
1750 if (p->fiber) in ksz8_config_cpu_port()
2080 if (dev->ports[phy].fiber) in ksz8463_w_phy()
|
| H A D | ksz_common.h | 134 u32 fiber:1; /* port is fiber */ member
|
| H A D | ksz_common.c | 5510 dev->ports[port_num].fiber = in ksz_switch_register()
|
| /linux/drivers/net/phy/ |
| H A D | marvell.c | 1665 int fiber, int status) in marvell_read_status_page_an() argument
1694 if (!fiber) { in marvell_read_status_page_an()
1736 int fiber; in marvell_read_status_page() local
1755 fiber = 1; in marvell_read_status_page()
1757 fiber = 0; in marvell_read_status_page()
1764 phydev->port = fiber ? PORT_FIBRE : PORT_TP; in marvell_read_status_page()
1766 if (fiber) { in marvell_read_status_page()
1780 err = marvell_read_status_page_an(phydev, fiber, status); in marvell_read_status_page()
|
| H A D | Kconfig | 439 fiber connections.
|
| /linux/arch/arm64/boot/dts/hisilicon/ |
| H A D | hip06.dtsi | 579 media-type = "fiber";
587 media-type = "fiber";
|
| H A D | hip07.dtsi | 1488 media-type = "fiber";
1498 media-type = "fiber";
|
| /linux/Documentation/networking/device_drivers/ethernet/intel/ |
| H A D | e1000e.rst | 327 between copper-based adapters and fiber-based adapters.
349 An Intel(R) Ethernet Network Adapter using fiber-based connections, however,
|
| H A D | e1000.rst | 341 If the board uses a fiber interface, these keywords are ignored, and the
342 fiber interface board only links at 1000 Mbps full-duplex.
|
| H A D | i40e.rst | 382 between copper-based adapters and fiber-based adapters.
407 An Intel(R) Ethernet Network Adapter using fiber-based connections, however,
|
| H A D | ixgbe.rst | 100 "ifconfig ethX down" turns off the laser for 82599-based SFP+ fiber adapters.
|
| H A D | ice.rst | 706 between copper-based adapters and fiber-based adapters.
|
| /linux/Documentation/devicetree/bindings/net/ |
| H A D | keystone-netcp.txt | 101 - mac<->fiber mode: 3
|
| /linux/Documentation/networking/device_drivers/ethernet/dlink/ |
| H A D | dl2k.rst | 232 available for fiber adapter.
|
| /linux/drivers/staging/most/Documentation/ |
| H A D | driver_usage.txt | 11 fiber optics, unshielded twisted pair cables (UTP) and coax cables. MOST
|
| /linux/Documentation/networking/device_drivers/ethernet/cirrus/ |
| H A D | cs89x0.rst | 71 or fiber networks).
|
| /linux/arch/mips/ |
| H A D | Kconfig | 414 in XPON (fiber) and DSL applications. They have SPI, PCI, USB,
|