sensor: Move hardware sensors from misc to a sensor directory

Lots of this are expected to be coming in, create a directory for them.

Also move the tmp105.h file into the include directory where it

sensor: Move hardware sensors from misc to a sensor directory

Lots of this are expected to be coming in, create a directory for them.

Also move the tmp105.h file into the include directory where it
should be.

Cc: Cédric Le Goater <clg@kaod.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: qemu-arm@nongnu.org
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Cédric Le Goater <clg@kaod.org>

show more ...

tmp105: Correct handling of temperature limit checks

The TMP105 datasheet says that in Interrupt Mode (when TM==1) the device
signals an alert when the temperature equals or exceeds the T_high value

tmp105: Correct handling of temperature limit checks

The TMP105 datasheet says that in Interrupt Mode (when TM==1) the device
signals an alert when the temperature equals or exceeds the T_high value and
then remains high until a device register is read or the device responds to
the SMBUS Alert Response address, or the device is put into Shutdown Mode.
Thereafter the Alert pin will only be re-signalled when temperature falls
below T_low; alert can then be cleared in the same set of ways, and the
device returns to its initial "alert when temperature goes above T_high"
mode. (If this textual description is confusing, see figure 3 in the
TI datasheet at https://www.ti.com/lit/gpn/tmp105 .)

We were misimplementing this as a simple "always alert if temperature is
above T_high or below T_low" condition, which gives a spurious alert on
startup if using the "T_high = 80 degrees C, T_low = 75 degrees C" reset
limit values.

Implement the correct (hysteresis) behaviour by tracking whether we
are currently looking for the temperature to rise over T_high or
for it to fall below T_low. Our implementation of the comparator
mode (TM==0) wasn't wrong, but rephrase it to match the way that
interrupt mode is now handled for clarity.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20201110150023.25533-3-peter.maydell@linaro.org

show more ...

Use OBJECT_DECLARE_SIMPLE_TYPE when possible

This converts existing DECLARE_INSTANCE_CHECKER usage to
OBJECT_DECLARE_SIMPLE_TYPE when possible.

$ ./scripts/codeconverter/converter.py -i \
--patte

Use OBJECT_DECLARE_SIMPLE_TYPE when possible

This converts existing DECLARE_INSTANCE_CHECKER usage to
OBJECT_DECLARE_SIMPLE_TYPE when possible.

$ ./scripts/codeconverter/converter.py -i \
--pattern=AddObjectDeclareSimpleType $(git grep -l '' -- '*.[ch]')

Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Message-Id: <20200916182519.415636-6-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>

show more ...

Use DECLARE_*CHECKER* macros

Generated using:

$ ./scripts/codeconverter/converter.py -i \
--pattern=TypeCheckMacro $(git grep -l '' -- '*.[ch]')

Reviewed-by: Daniel P. Berrangé <berrange@redha

Use DECLARE_*CHECKER* macros

Generated using:

$ ./scripts/codeconverter/converter.py -i \
--pattern=TypeCheckMacro $(git grep -l '' -- '*.[ch]')

Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-12-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-13-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-14-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>

show more ...

Move QOM typedefs and add missing includes

Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TY

Move QOM typedefs and add missing includes

Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.

Patch generated using:

$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')

which will split "typdef struct { ... } TypedefName"
declarations.

Followed by:

$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')

which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary

Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>

show more ...

hw: move private headers to hw/ subdirectories.

Many headers are used only in a single directory. These can be
kept in hw/.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

hw: move headers to include/

Many of these should be cleaned up with proper qdev-/QOM-ification.
Right now there are many catch-all headers in include/hw/ARCH depending
on cpu.h, and this makes it n

hw: move headers to include/

Many of these should be cleaned up with proper qdev-/QOM-ification.
Right now there are many catch-all headers in include/hw/ARCH depending
on cpu.h, and this makes it necessary to compile these files per-target.
However, fixing this does not belong in these patches.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

hw: include hw header files with full paths

Done with this script:

cd hw
for i in `find . -name '*.h' | sed 's/^..//'`; do
echo '\,^#.*include.*["<]'$i'[">], s,'$i',hw/&,'
done | sed -i -f - `fin

hw: include hw header files with full paths

Done with this script:

cd hw
for i in `find . -name '*.h' | sed 's/^..//'`; do
echo '\,^#.*include.*["<]'$i'[">], s,'$i',hw/&,'
done | sed -i -f - `find . -type f`

This is so that paths remain valid as files are moved.

Instead, files in hw/dataplane are referenced with the relative path.
We know they are not going to move to include/, and they are the only
include files that are in subdirectories _and_ move.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

tmp105: Add temperature QOM property

This obsoletes tmp105_set() and allows for better error handling.

Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Anthony Liguori <aliguor

tmp105: Add temperature QOM property

This obsoletes tmp105_set() and allows for better error handling.

Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>

show more ...

tmp105: QOM'ify

Introduce TYPE_ constant and cast macro.
Move the state struct to the new header to allow for future embedding.

Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Reviewed-by: A

tmp105: QOM'ify

Introduce TYPE_ constant and cast macro.
Move the state struct to the new header to allow for future embedding.

Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>

show more ...

tmp105: Split out I2C message constants from header

Allows value sharing with qtest.

Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed

tmp105: Split out I2C message constants from header

Allows value sharing with qtest.

Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>

show more ...

tmp105: Create API for TMP105 temperature sensor.

* Define enum for TMP105 registers
* Move tmp105_set() from I2C to TMP105 header
* Document units and range of temperature as preconditions

Reviewe

tmp105: Create API for TMP105 temperature sensor.

* Define enum for TMP105 registers
* Move tmp105_set() from I2C to TMP105 header
* Document units and range of temperature as preconditions

Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alex Horn <alex.horn@cs.ox.ac.uk>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>

show more ...