Merge branches 'fixes' and 'misc' into for-linus

Merge tag 'mmc-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
"MMC core:
- Convert to sysfs_emit() in favor of sprintf()

- Improve fallba

Merge tag 'mmc-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
"MMC core:
- Convert to sysfs_emit() in favor of sprintf()

- Improve fallback to speed modes if eMMC HS200 fails

MMC host:
- dw_mmc: Allow variants to set minimal supported clock rate

- dw-mmc-rockchip: Fix problems with invalid clock rates

- litex_mmc: Add new DT based driver for the LiteX's LiteSDCard
interface

- litex_mmc: Add Gabriel Somlo and Joel Stanley as co-maintainers for
LiteX

- mtk-sd: Add support for the Mediatek MT8186 variant

- renesas_sdhi: Add support for RZ/G2UL variant

- renesas_sdhi: Add support for RZ/V2L variant

- rtsx_pci: Adjust power-on sequence to conform to the SD spec

- sdhci-am654: Add support for TI's AM62 variant

- sdhci_am654: Fixup support for TI's AM64 variant

- sdhci-esdhc-imx: Add support for the imx93 variant

- sdhci-msm: Add support for the msm8953 variant

- sdhci-pci-gli: Add support for runtime PM for the GL9763E variant

- sdhci-pci-gli: Adjustments of the SSC function for the GL975x
variants

- sdhci-tegra: Add support for wake on SD card event

- sunxi-mmc: Add support for Allwinner's F1c100s variant

- sunxi-mmc: Add support for D1 MMC variant"

* tag 'mmc-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (37 commits)
dt-bindings: mmc: renesas,sdhi: Document RZ/G2UL SoC
mmc: tmio: remove outdated members from host struct
mmc: mtk-sd: Silence delay phase calculation debug log
mmc: davinci_mmc: Handle error for clk_enable
mmc: sdhci-pci-gli: Add runtime PM for GL9763E
mmc: core: Drop HS400 caps unless 8-bit bus is supported too
mmc: host: Return an error when ->enable_sdio_irq() ops is missing
mmc: core: Improve fallback to speed modes if eMMC HS200 fails
dt-bindings: mmc: sunxi: add Allwinner F1c100s compatible
mmc: dw-mmc-rockchip: Fix handling invalid clock rates
mmc: dw_mmc: Support setting f_min from host drivers
mmc: host: Drop commas after SoC match table sentinels
mmc: rtsx: add 74 Clocks in power on flow
dt-bindings: mmc: renesas,sdhi: Document RZ/V2L SoC
mmc: sh_mmcif: Simplify division/shift logic
mmc: sdhci_am654: Add Support for TI's AM62 SoC
dt-bindings: mmc: imx-esdhc: Add imx93 compatible string
dt-bindings: mmc: sdhci-am654: Add compatible string for AM62 SoC
mmc: sdhci_am654: Fix the driver data of AM64 SoC
mmc: core: use sysfs_emit() instead of sprintf()
...

show more ...

Merge branch 'for-5.18/amd-sfh' into for-linus

- dead code elimination (Christophe JAILLET)

mmc: dw_mmc: Support setting f_min from host drivers

Host drivers may not be able to support frequencies as low as dw-mmc
supports. Unfortunately f_min isn't available when the drv_data->init
functi

mmc: dw_mmc: Support setting f_min from host drivers

Host drivers may not be able to support frequencies as low as dw-mmc
supports. Unfortunately f_min isn't available when the drv_data->init
function is called, as the mmc_host struct hasn't been set up yet.

Support the host drivers saving the requested minimum frequency, so we
can later set f_min when it is available.

Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20220305215835.2210388-2-pgwipeout@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

show more ...

Merge tag 'v5.17-rc4' into for-linus

Merge with mainline to get the Intel ASoC generic helpers header and
other changes.

mmc: dw_mmc: Use device_property_string_array_count()

Use device_property_string_array_count() to get number of strings
in a string array property.

Signed-off-by: Andy Shevchenko <andriy.shevchenko

mmc: dw_mmc: Use device_property_string_array_count()

Use device_property_string_array_count() to get number of strings
in a string array property.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220202182450.54925-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

show more ...

mmc: dw_mmc: Fix potential null pointer risk

we previously assumed 'host->slot' could be null,
null pointer judgment should be added

Signed-off-by: Wen Zhiwei <wenzhiwei@kylinos.cn>
Reviewed-by: Ja

mmc: dw_mmc: Fix potential null pointer risk

we previously assumed 'host->slot' could be null,
null pointer judgment should be added

Signed-off-by: Wen Zhiwei <wenzhiwei@kylinos.cn>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20211229023814.53372-1-wenzhiwei@kylinos.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

show more ...

Merge tag 'v5.17-rc4' into next

Sync up with mainline to get the latest changes in HID subsystem.

Merge remote-tracking branch 'drm/drm-next' into drm-misc-next

First backmerge into drm-misc-next. Required for more helpers backmerged,
and to pull in 5.17 (rc2).

Signed-off-by: Maarten Lankhorst

Merge remote-tracking branch 'drm/drm-next' into drm-misc-next

First backmerge into drm-misc-next. Required for more helpers backmerged,
and to pull in 5.17 (rc2).

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

show more ...

Merge tag 'kvmarm-fixes-5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD

KVM/arm64 fixes for 5.17, take #2

- A couple of fixes when handling an exception while a SEr

Merge tag 'kvmarm-fixes-5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD

KVM/arm64 fixes for 5.17, take #2

- A couple of fixes when handling an exception while a SError has been
delivered

- Workaround for Cortex-A510's single-step[ erratum

show more ...

Merge drm/drm-next into drm-intel-gt-next

Backmerge to bring in 5.17-rc2 to introduce a common baseline
to merge i915_regs changes from drm-intel-next.

Signed-off-by: Joonas Lahtinen <joonas.lahtin

Merge drm/drm-next into drm-intel-gt-next

Backmerge to bring in 5.17-rc2 to introduce a common baseline
to merge i915_regs changes from drm-intel-next.

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

show more ...

Merge drm/drm-next into drm-intel-next

Catch-up with 5.17-rc2 and trying to align with drm-intel-gt-next
for a possible topic branch for merging the split of i915_regs...

Signed-off-by: Rodrigo Viv

Merge drm/drm-next into drm-intel-next

Catch-up with 5.17-rc2 and trying to align with drm-intel-gt-next
for a possible topic branch for merging the split of i915_regs...

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

show more ...

Merge drm/drm-fixes into drm-misc-fixes

Backmerging drm/drm-fixes into drm-misc-fixes for v5.17-rc1.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge tag 'v5.16' into next

Sync up with mainline to bring in the latest API changes.

Merge branch 'next' into for-linus

Prepare input updates for 5.17 merge window.

Merge remote-tracking branch 'torvalds/master' into perf/core

To pick up fixes and get in line with other trees, powerpc kernel
mostly this time, but BPF as well.

Signed-off-by: Arnaldo Carvalho de

Merge remote-tracking branch 'torvalds/master' into perf/core

To pick up fixes and get in line with other trees, powerpc kernel
mostly this time, but BPF as well.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

show more ...

Merge tag 'mmc-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
"MMC core:
- Use common polling loop for CMD1
- Add support for DT compatibl

Merge tag 'mmc-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
"MMC core:
- Use common polling loop for CMD1
- Add support for DT compatibles for card quirks and use it for ti,wl1251
- Fixup storing of the OCR mask for MMC_QUIRK_NONSTD_SDIO

MMC host:
- dw_mmc: Add support for MMC_GEN_CMDs
- dw_mmc: Fixup calculation of the data timeout
- dw_mmc-exynos: Add support for the ARTPEC-8 variant
- jz4740: Add support for bi-directional DMA channels
- mmci: Add support for eMMC HS200 mode for the stm32 sdmmc variant
- mmci: Add support for stm32 sdmmc variant revision v2.2
- mtk-sd: A couple of various minor improvements
- omap_hsmmc: Drop redundant initialization for the ti,wl1251 chip
- sdhci-esdhc-imx: Add support for the i.MXRT series variant
- sdhci-esdhc-imx: Add Haibo Chen as maintainer
- sdhci-pci: Add support for the Intel ADL variant
- sdhci-pci-gli: GL975[50]: Add support for the Apple ARM64 variant
- sdhci-pci-o2micro: Improve support for SDR104/HS200"

* tag 'mmc-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (54 commits)
dt-bindings: mmc: synopsys-dw-mshc: integrate Altera and Imagination
mmc: pwrseq: Use bitmap_free() to free bitmap
dt-bindings: mmc: PL18x stop relying on order of dma-names
dt-bindings: mmc: sdhci-msm: Add compatible string for msm8994
mmc: au1xmmc: propagate errors from platform_get_irq()
mmc: sdhci-pci-o2micro: Restore the SD clock's base clock frequency
mmc: sdhci-pci-o2micro: Improve card input timing at SDR104/HS200 mode
mmc: mtk-sd: Assign src_clk parent to src_clk_cg for legacy DTs
mmc: mtk-sd: Fix usage of devm_clk_get_optional()
mmc: mtk-sd: Take action for no-sdio device-tree parameter
mmc: mtk-sd: Use BIT() and GENMASK() macros to describe fields
mmc: mtk-sd: Use readl_poll_timeout instead of open-coded polling
MAINTAINERS: Add i.MX sdhci maintainer
mmc: jz4740: Support using a bi-directional DMA channel
dt-bindings: mmc: ingenic: Support using bi-directional DMA channel
mmc: dw_mmc: Do not wait for DTO in case of error
mmc: dw_mmc: Add driver callbacks for data read timeout
mmc: dw_mmc-exynos: Add support for ARTPEC-8
dt-bindings: mmc: exynos-dw-mshc: Add support for ARTPEC-8
mmc: meson-mx-sdio: add IRQ check
...

show more ...

Merge branch 'for-next' into for-linus

Pull 5.17 materials.

Signed-off-by: Takashi Iwai <tiwai@suse.de>

mmc: dw_mmc: Do not wait for DTO in case of error

When running the ARTPEC-8 DWMMC IP version, and a data error interrupt
comes during a data read transfer, there is no guarantee for the data
transfe

mmc: dw_mmc: Do not wait for DTO in case of error

When running the ARTPEC-8 DWMMC IP version, and a data error interrupt
comes during a data read transfer, there is no guarantee for the data
transfer over interrupt (DTO) to come within the specified data timeout.
This case is handled by the dto_timer handler which will complete the
request with the comment:

/*
* If DTO interrupt does NOT come in sending data state,
* we should notify the driver to terminate current transfer
* and report a data timeout to the core.
*/

But since the ARTPEC-8 DWMMC IP version, supports an extended TMOUT
register which allows longer timeouts than the non ARTPEC-8 version
does, waiting for the dto_timer to complete the request in error cases
may cause the request to take significantly longer time than necessary.
This is specifically true for the failing steps during tuning of a
device.

Fix this by completing the request when the error interrupt comes. Since
this fix is specific for the ARTPEC-8, a quirk is added.

Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20211220113026.21129-5-marten.lindahl@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

show more ...

mmc: dw_mmc: Add driver callbacks for data read timeout

Current dw_mci driver supports a TMOUT register which consists of a 24
bit field (TMOUT[31:8]) for the DATA_TIMEOUT. The maximum value of this

mmc: dw_mmc: Add driver callbacks for data read timeout

Current dw_mci driver supports a TMOUT register which consists of a 24
bit field (TMOUT[31:8]) for the DATA_TIMEOUT. The maximum value of this
field is 0xFFFFFF, which with a 200MHz clock will give a full DRTO of:

0xFFFFFF / 200000000 => ~84 ms

However, the ARTPEC-8 SoC DWMMC IP version has a TMOUT register with an
extended DATA_TIMEOUT field, which supports longer timers for the DRTO.
In this version the DATA_TIMEOUT field is split into two, which with the
same 200MHz clock as above will allow a maximum timeout of:

((TMOUT[10:8] -1) * 0xFFFFFF + TMOUT[31:11] * 8) / 200000000 => ~587 ms

Add driver callbacks for implementation specific data timeout, and
implement callback functions for the ARTPEC-8 SoC.

Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211220113026.21129-4-marten.lindahl@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

show more ...

mmc: dw_mmc: clean up a debug message

The "0x" prefix is redundant when # flag is used. It prints "0x0x".

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mårten Lindahl <marte

mmc: dw_mmc: clean up a debug message

The "0x" prefix is redundant when # flag is used. It prints "0x0x".

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20211217150348.GD16611@kili
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

show more ...

Merge drm/drm-next into drm-misc-next-fixes

Backmerging to bring drm-misc-next-fixes up to the latest state for
the current release cycle.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

mmc: dw_mmc: add common capabilities to replace caps

The caps field depends on the mshcN alias ID but for some devices this
is unnecessary as the capabilities are the same for all instances
sharing

mmc: dw_mmc: add common capabilities to replace caps

The caps field depends on the mshcN alias ID but for some devices this
is unnecessary as the capabilities are the same for all instances
sharing the same compatible.

Add a common_caps field for this case which updates the host's
capabilities without needing the mshcN alias ID.

Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20211124184603.3897245-2-john@metanate.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

show more ...

mmc: dw_mmc: Allow lower TMOUT value than maximum

The TMOUT register is always set with a full value for every transfer,
which (with a 200MHz clock) will give a full DRTO of ~84 milliseconds.
This i

mmc: dw_mmc: Allow lower TMOUT value than maximum

The TMOUT register is always set with a full value for every transfer,
which (with a 200MHz clock) will give a full DRTO of ~84 milliseconds.
This is normally good enough to complete the request, but setting a full
value makes it impossible to test shorter timeouts, when for example
testing data read times on different SD cards.

Add a function to set any value smaller than the maximum of 0xFFFFFF.

Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20211119155337.14341-1-marten.lindahl@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

show more ...

mmc: dw_mmc: Avoid hung state if GEN_CMD transfer fails

If we get a data error during a block transfer command, a stop command
(CMD12) is normally initiated. But this does not work for the general
c

mmc: dw_mmc: Avoid hung state if GEN_CMD transfer fails

If we get a data error during a block transfer command, a stop command
(CMD12) is normally initiated. But this does not work for the general
command (CMD56), but instead the action is ignored and an uninitialized
command struct is used for the stop action, with unexpected result.

Fix this by adding a check for GEN_CMD when preparing stop transmission.

Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20211103182716.28419-1-marten.lindahl@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

show more ...