ARM: dts: Move .dts files to vendor sub-directories

The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .

ARM: dts: Move .dts files to vendor sub-directories

The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.

There's no change to dtbs_install as the flat structure is maintained on
install.

The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
company (e.g. gemini, nspire)

The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com> #Xilinx
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com> #hisilicon
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #broadcom
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>

show more ...

ARM: dts: Unify pinctrl-single pin group nodes for dra7

We want to unify the pinctrl-single pin group nodes to use naming "pins".
Otherwise non-standad pin group names will add make dtbs checks erro

ARM: dts: Unify pinctrl-single pin group nodes for dra7

We want to unify the pinctrl-single pin group nodes to use naming "pins".
Otherwise non-standad pin group names will add make dtbs checks errors
when the pinctrl-single yaml binding gets merged.

Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

show more ...

ARM: dts: dra7-mmc-iodelay: Add a new pinctrl group for clk line without pullup

During a short period when the bus voltage is switched from 3.3v to 1.8v,
(to enumerate UHS mode), the mmc module is d

ARM: dts: dra7-mmc-iodelay: Add a new pinctrl group for clk line without pullup

During a short period when the bus voltage is switched from 3.3v to 1.8v,
(to enumerate UHS mode), the mmc module is disabled and the mmc IO lines
are kept in a state according to the programmed pad mux pull type.

According to 4.2.4.2 Timing to Switch Signal Voltage in "SD Specifications
Part 1 Physical Layer Specification Version 5.00 February 22, 2016", the
host should hold CLK low for at least 5ms.

In order to keep the card line low during voltage switch, the pad mux of
mmc1_clk line should be configured to pull down.

Add a new pinctrl group for clock line without pullup to be used in boards
where mmc1_clk line is not connected to an external pullup.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

show more ...