xref: /qemu/hw/arm/realview.c (revision 6621cf52509b796f3c32a18b74248cf404dbe56f)

/*
 * ARM RealView Baseboard System emulation.
 *
 * Copyright (c) 2006-2007 CodeSourcery.
 * Written by Paul Brook
 *
 * This code is licensed under the GPL.
 */

#include "qemu/osdep.h"
#include "qapi/error.h"
#include "cpu.h"
#include "hw/sysbus.h"
#include "hw/arm/boot.h"
#include "hw/arm/primecell.h"
#include "hw/core/split-irq.h"
#include "hw/net/lan9118.h"
#include "hw/net/smc91c111.h"
#include "hw/pci/pci.h"
#include "hw/qdev-core.h"
#include "net/net.h"
#include "system/system.h"
#include "hw/boards.h"
#include "hw/i2c/i2c.h"
#include "qemu/error-report.h"
#include "hw/char/pl011.h"
#include "hw/cpu/a9mpcore.h"
#include "hw/intc/realview_gic.h"
#include "hw/irq.h"
#include "hw/i2c/arm_sbcon_i2c.h"
#include "hw/sd/sd.h"
#include "audio/audio.h"
#include "target/arm/cpu-qom.h"

#define SMP_BOOT_ADDR 0xe0000000
#define SMP_BOOTREG_ADDR 0x10000030

#define GIC_EXT_IRQS 64 /* Realview PBX-A9 development board */

/* Board init.  */

static struct arm_boot_info realview_binfo = {
    .smp_loader_start = SMP_BOOT_ADDR,
    .smp_bootreg_addr = SMP_BOOTREG_ADDR,
};

/* The following two lists must be consistent.  */
enum realview_board_type {
    BOARD_EB,
    BOARD_EB_MPCORE,
    BOARD_PB_A8,
    BOARD_PBX_A9,
};

static const int realview_board_id[] = {
    0x33b,
    0x33b,
    0x769,
    0x76d
};

static void split_irq_from_named(DeviceState *src, const char* outname,
                                 qemu_irq out1, qemu_irq out2) {
    DeviceState *splitter = qdev_new(TYPE_SPLIT_IRQ);

    qdev_prop_set_uint32(splitter, "num-lines", 2);

    qdev_realize_and_unref(splitter, NULL, &error_fatal);

    qdev_connect_gpio_out(splitter, 0, out1);
    qdev_connect_gpio_out(splitter, 1, out2);
    qdev_connect_gpio_out_named(src, outname, 0,
                                qdev_get_gpio_in(splitter, 0));
}

static void realview_init(MachineState *machine,
                          enum realview_board_type board_type)
{
    ARMCPU *cpu = NULL;
    CPUARMState *env;
    MemoryRegion *sysmem = get_system_memory();
    MemoryRegion *ram_lo;
    MemoryRegion *ram_hi = g_new(MemoryRegion, 1);
    MemoryRegion *ram_alias = g_new(MemoryRegion, 1);
    MemoryRegion *ram_hack = g_new(MemoryRegion, 1);
    DeviceState *dev, *sysctl, *gpio2, *pl041;
    SysBusDevice *busdev;
    qemu_irq pic[64];
    PCIBus *pci_bus = NULL;
    DriveInfo *dinfo;
    I2CBus *i2c;
    int n;
    unsigned int smp_cpus = machine->smp.cpus;
    qemu_irq cpu_irq[4];
    int is_mpcore = 0;
    int is_pb = 0;
    uint32_t proc_id = 0;
    uint32_t sys_id;
    ram_addr_t low_ram_size;
    ram_addr_t ram_size = machine->ram_size;
    hwaddr periphbase = 0;

    switch (board_type) {
    case BOARD_EB:
        break;
    case BOARD_EB_MPCORE:
        is_mpcore = 1;
        periphbase = 0x10100000;
        break;
    case BOARD_PB_A8:
        is_pb = 1;
        break;
    case BOARD_PBX_A9:
        is_mpcore = 1;
        is_pb = 1;
        periphbase = 0x1f000000;
        break;
    }

    for (n = 0; n < smp_cpus; n++) {
        Object *cpuobj = object_new(machine->cpu_type);

        /* By default A9,A15 and ARM1176 CPUs have EL3 enabled.  This board
         * does not currently support EL3 so the CPU EL3 property is disabled
         * before realization.
         */
        if (object_property_find(cpuobj, "has_el3")) {
            object_property_set_bool(cpuobj, "has_el3", false, &error_fatal);
        }

        if (is_pb && is_mpcore) {
            object_property_set_int(cpuobj, "reset-cbar", periphbase,
                                    &error_fatal);
        }

        qdev_realize(DEVICE(cpuobj), NULL, &error_fatal);

        cpu_irq[n] = qdev_get_gpio_in(DEVICE(cpuobj), ARM_CPU_IRQ);
    }
    cpu = ARM_CPU(first_cpu);
    env = &cpu->env;
    if (arm_feature(env, ARM_FEATURE_V7)) {
        if (is_mpcore) {
            proc_id = 0x0c000000;
        } else {
            proc_id = 0x0e000000;
        }
    } else if (arm_feature(env, ARM_FEATURE_V6K)) {
        proc_id = 0x06000000;
    } else if (arm_feature(env, ARM_FEATURE_V6)) {
        proc_id = 0x04000000;
    } else {
        proc_id = 0x02000000;
    }

    if (is_pb && ram_size > 0x20000000) {
        /* Core tile RAM.  */
        ram_lo = g_new(MemoryRegion, 1);
        low_ram_size = ram_size - 0x20000000;
        ram_size = 0x20000000;
        memory_region_init_ram(ram_lo, NULL, "realview.lowmem", low_ram_size,
                               &error_fatal);
        memory_region_add_subregion(sysmem, 0x20000000, ram_lo);
    }

    memory_region_init_ram(ram_hi, NULL, "realview.highmem", ram_size,
                           &error_fatal);
    low_ram_size = ram_size;
    if (low_ram_size > 0x10000000)
      low_ram_size = 0x10000000;
    /* SDRAM at address zero.  */
    memory_region_init_alias(ram_alias, NULL, "realview.alias",
                             ram_hi, 0, low_ram_size);
    memory_region_add_subregion(sysmem, 0, ram_alias);
    if (is_pb) {
        /* And again at a high address.  */
        memory_region_add_subregion(sysmem, 0x70000000, ram_hi);
    } else {
        ram_size = low_ram_size;
    }

    sys_id = is_pb ? 0x01780500 : 0xc1400400;
    sysctl = qdev_new("realview_sysctl");
    qdev_prop_set_uint32(sysctl, "sys_id", sys_id);
    qdev_prop_set_uint32(sysctl, "proc_id", proc_id);
    sysbus_realize_and_unref(SYS_BUS_DEVICE(sysctl), &error_fatal);
    sysbus_mmio_map(SYS_BUS_DEVICE(sysctl), 0, 0x10000000);

    if (is_mpcore) {
        if (is_pb) {
            dev = qdev_new(TYPE_A9MPCORE_PRIV);
            qdev_prop_set_uint32(dev, "num-irq", GIC_EXT_IRQS + GIC_INTERNAL);
        } else {
            dev = qdev_new("realview_mpcore");
        }
        qdev_prop_set_uint32(dev, "num-cpu", smp_cpus);
        busdev = SYS_BUS_DEVICE(dev);
        sysbus_realize_and_unref(busdev, &error_fatal);
        sysbus_mmio_map(busdev, 0, periphbase);
        for (n = 0; n < smp_cpus; n++) {
            sysbus_connect_irq(busdev, n, cpu_irq[n]);
        }
        sysbus_create_varargs("l2x0", periphbase + 0x2000, NULL);
        /* Both A9 and 11MPCore put the GIC CPU i/f at base + 0x100 */
        realview_binfo.gic_cpu_if_addr = periphbase + 0x100;
    } else {
        uint32_t gic_addr = is_pb ? 0x1e000000 : 0x10040000;
        /* For now just create the nIRQ GIC, and ignore the others.  */
        dev = sysbus_create_simple(TYPE_REALVIEW_GIC, gic_addr, cpu_irq[0]);
    }
    for (n = 0; n < GIC_EXT_IRQS; n++) {
        pic[n] = qdev_get_gpio_in(dev, n);
    }

    pl041 = qdev_new("pl041");
    qdev_prop_set_uint32(pl041, "nc_fifo_depth", 512);
    if (machine->audiodev) {
        qdev_prop_set_string(pl041, "audiodev", machine->audiodev);
    }
    sysbus_realize_and_unref(SYS_BUS_DEVICE(pl041), &error_fatal);
    sysbus_mmio_map(SYS_BUS_DEVICE(pl041), 0, 0x10004000);
    sysbus_connect_irq(SYS_BUS_DEVICE(pl041), 0, pic[19]);

    sysbus_create_simple("pl050_keyboard", 0x10006000, pic[20]);
    sysbus_create_simple("pl050_mouse", 0x10007000, pic[21]);

    pl011_create(0x10009000, pic[12], serial_hd(0));
    pl011_create(0x1000a000, pic[13], serial_hd(1));
    pl011_create(0x1000b000, pic[14], serial_hd(2));
    pl011_create(0x1000c000, pic[15], serial_hd(3));

    /* DMA controller is optional, apparently.  */
    dev = qdev_new("pl081");
    object_property_set_link(OBJECT(dev), "downstream", OBJECT(sysmem),
                             &error_fatal);
    busdev = SYS_BUS_DEVICE(dev);
    sysbus_realize_and_unref(busdev, &error_fatal);
    sysbus_mmio_map(busdev, 0, 0x10030000);
    sysbus_connect_irq(busdev, 0, pic[24]);

    sysbus_create_simple("sp804", 0x10011000, pic[4]);
    sysbus_create_simple("sp804", 0x10012000, pic[5]);

    sysbus_create_simple("pl061", 0x10013000, pic[6]);
    sysbus_create_simple("pl061", 0x10014000, pic[7]);
    gpio2 = sysbus_create_simple("pl061", 0x10015000, pic[8]);

    dev = qdev_new("pl111");
    object_property_set_link(OBJECT(dev), "framebuffer-memory",
                             OBJECT(sysmem), &error_fatal);
    sysbus_realize_and_unref(SYS_BUS_DEVICE(dev), &error_fatal);
    sysbus_mmio_map(SYS_BUS_DEVICE(dev), 0, 0x10020000);
    sysbus_connect_irq(SYS_BUS_DEVICE(dev), 0, pic[23]);

    dev = sysbus_create_varargs("pl181", 0x10005000, pic[17], pic[18], NULL);
    /* Wire up MMC card detect and read-only signals. These have
     * to go to both the PL061 GPIO and the sysctl register.
     * Note that the PL181 orders these lines (readonly,inserted)
     * and the PL061 has them the other way about. Also the card
     * detect line is inverted.
     */
    split_irq_from_named(dev, "card-read-only",
                   qdev_get_gpio_in(sysctl, ARM_SYSCTL_GPIO_MMC_WPROT),
                   qdev_get_gpio_in(gpio2, 1));

    split_irq_from_named(dev, "card-inserted",
                   qdev_get_gpio_in(sysctl, ARM_SYSCTL_GPIO_MMC_CARDIN),
                   qemu_irq_invert(qdev_get_gpio_in(gpio2, 0)));

    dinfo = drive_get(IF_SD, 0, 0);
    if (dinfo) {
        DeviceState *card;

        card = qdev_new(TYPE_SD_CARD);
        qdev_prop_set_drive_err(card, "drive", blk_by_legacy_dinfo(dinfo),
                                &error_fatal);
        qdev_realize_and_unref(card, qdev_get_child_bus(dev, "sd-bus"),
                               &error_fatal);
    }

    sysbus_create_simple("pl031", 0x10017000, pic[10]);

    if (!is_pb) {
        dev = qdev_new("realview_pci");
        busdev = SYS_BUS_DEVICE(dev);
        sysbus_realize_and_unref(busdev, &error_fatal);
        sysbus_mmio_map(busdev, 0, 0x10019000); /* PCI controller registers */
        sysbus_mmio_map(busdev, 1, 0x60000000); /* PCI self-config */
        sysbus_mmio_map(busdev, 2, 0x61000000); /* PCI config */
        sysbus_mmio_map(busdev, 3, 0x62000000); /* PCI I/O */
        sysbus_mmio_map(busdev, 4, 0x63000000); /* PCI memory window 1 */
        sysbus_mmio_map(busdev, 5, 0x64000000); /* PCI memory window 2 */
        sysbus_mmio_map(busdev, 6, 0x68000000); /* PCI memory window 3 */
        sysbus_connect_irq(busdev, 0, pic[48]);
        sysbus_connect_irq(busdev, 1, pic[49]);
        sysbus_connect_irq(busdev, 2, pic[50]);
        sysbus_connect_irq(busdev, 3, pic[51]);
        pci_bus = (PCIBus *)qdev_get_child_bus(dev, "pci");
        if (machine_usb(machine)) {
            pci_create_simple(pci_bus, -1, "pci-ohci");
        }
        n = drive_get_max_bus(IF_SCSI);
        while (n >= 0) {
            dev = DEVICE(pci_create_simple(pci_bus, -1, "lsi53c895a"));
            lsi53c8xx_handle_legacy_cmdline(dev);
            n--;
        }
    }

    if (qemu_find_nic_info(is_pb ? "lan9118" : "smc91c111", true, NULL)) {
        if (is_pb) {
            lan9118_init(0x4e000000, pic[28]);
        } else {
            smc91c111_init(0x4e000000, pic[28]);
        }
    }

    if (pci_bus) {
        pci_init_nic_devices(pci_bus, "rtl8139");
    }

    dev = sysbus_create_simple(TYPE_ARM_SBCON_I2C, 0x10002000, NULL);
    i2c = (I2CBus *)qdev_get_child_bus(dev, "i2c");
    i2c_slave_create_simple(i2c, "ds1338", 0x68);

    /* Memory map for RealView Emulation Baseboard:  */
    /* 0x10000000 System registers.  */
    /*  0x10001000 System controller.  */
    /* 0x10002000 Two-Wire Serial Bus.  */
    /* 0x10003000 Reserved.  */
    /*  0x10004000 AACI.  */
    /*  0x10005000 MCI.  */
    /* 0x10006000 KMI0.  */
    /* 0x10007000 KMI1.  */
    /*  0x10008000 Character LCD. (EB) */
    /* 0x10009000 UART0.  */
    /* 0x1000a000 UART1.  */
    /* 0x1000b000 UART2.  */
    /* 0x1000c000 UART3.  */
    /*  0x1000d000 SSPI.  */
    /*  0x1000e000 SCI.  */
    /* 0x1000f000 Reserved.  */
    /*  0x10010000 Watchdog.  */
    /* 0x10011000 Timer 0+1.  */
    /* 0x10012000 Timer 2+3.  */
    /*  0x10013000 GPIO 0.  */
    /*  0x10014000 GPIO 1.  */
    /*  0x10015000 GPIO 2.  */
    /*  0x10002000 Two-Wire Serial Bus - DVI. (PB) */
    /* 0x10017000 RTC.  */
    /*  0x10018000 DMC.  */
    /*  0x10019000 PCI controller config.  */
    /*  0x10020000 CLCD.  */
    /* 0x10030000 DMA Controller.  */
    /* 0x10040000 GIC1. (EB) */
    /*  0x10050000 GIC2. (EB) */
    /*  0x10060000 GIC3. (EB) */
    /*  0x10070000 GIC4. (EB) */
    /*  0x10080000 SMC.  */
    /* 0x1e000000 GIC1. (PB) */
    /*  0x1e001000 GIC2. (PB) */
    /*  0x1e002000 GIC3. (PB) */
    /*  0x1e003000 GIC4. (PB) */
    /*  0x40000000 NOR flash.  */
    /*  0x44000000 DoC flash.  */
    /*  0x48000000 SRAM.  */
    /*  0x4c000000 Configuration flash.  */
    /* 0x4e000000 Ethernet.  */
    /*  0x4f000000 USB.  */
    /*  0x50000000 PISMO.  */
    /*  0x54000000 PISMO.  */
    /*  0x58000000 PISMO.  */
    /*  0x5c000000 PISMO.  */
    /* 0x60000000 PCI.  */
    /* 0x60000000 PCI Self Config.  */
    /* 0x61000000 PCI Config.  */
    /* 0x62000000 PCI IO.  */
    /* 0x63000000 PCI mem 0.  */
    /* 0x64000000 PCI mem 1.  */
    /* 0x68000000 PCI mem 2.  */

    /* ??? Hack to map an additional page of ram for the secondary CPU
       startup code.  I guess this works on real hardware because the
       BootROM happens to be in ROM/flash or in memory that isn't clobbered
       until after Linux boots the secondary CPUs.  */
    memory_region_init_ram(ram_hack, NULL, "realview.hack", 0x1000,
                           &error_fatal);
    memory_region_add_subregion(sysmem, SMP_BOOT_ADDR, ram_hack);

    realview_binfo.ram_size = ram_size;
    realview_binfo.board_id = realview_board_id[board_type];
    realview_binfo.loader_start = (board_type == BOARD_PB_A8 ? 0x70000000 : 0);
    arm_load_kernel(cpu, machine, &realview_binfo);
}

static void realview_eb_init(MachineState *machine)
{
    realview_init(machine, BOARD_EB);
}

static void realview_eb_mpcore_init(MachineState *machine)
{
    realview_init(machine, BOARD_EB_MPCORE);
}

static void realview_pb_a8_init(MachineState *machine)
{
    realview_init(machine, BOARD_PB_A8);
}

static void realview_pbx_a9_init(MachineState *machine)
{
    realview_init(machine, BOARD_PBX_A9);
}

static void realview_eb_class_init(ObjectClass *oc, void *data)
{
    MachineClass *mc = MACHINE_CLASS(oc);

    mc->desc = "ARM RealView Emulation Baseboard (ARM926EJ-S)";
    mc->init = realview_eb_init;
    mc->block_default_type = IF_SCSI;
    mc->ignore_memory_transaction_failures = true;
    mc->default_cpu_type = ARM_CPU_TYPE_NAME("arm926");
    mc->auto_create_sdcard = true;

    machine_add_audiodev_property(mc);
}

static const TypeInfo realview_eb_type = {
    .name = MACHINE_TYPE_NAME("realview-eb"),
    .parent = TYPE_MACHINE,
    .class_init = realview_eb_class_init,
};

static void realview_eb_mpcore_class_init(ObjectClass *oc, void *data)
{
    MachineClass *mc = MACHINE_CLASS(oc);

    mc->desc = "ARM RealView Emulation Baseboard (ARM11MPCore)";
    mc->init = realview_eb_mpcore_init;
    mc->block_default_type = IF_SCSI;
    mc->max_cpus = 4;
    mc->ignore_memory_transaction_failures = true;
    mc->default_cpu_type = ARM_CPU_TYPE_NAME("arm11mpcore");
    mc->auto_create_sdcard = true;

    machine_add_audiodev_property(mc);
}

static const TypeInfo realview_eb_mpcore_type = {
    .name = MACHINE_TYPE_NAME("realview-eb-mpcore"),
    .parent = TYPE_MACHINE,
    .class_init = realview_eb_mpcore_class_init,
};

static void realview_pb_a8_class_init(ObjectClass *oc, void *data)
{
    MachineClass *mc = MACHINE_CLASS(oc);

    mc->desc = "ARM RealView Platform Baseboard for Cortex-A8";
    mc->init = realview_pb_a8_init;
    mc->ignore_memory_transaction_failures = true;
    mc->default_cpu_type = ARM_CPU_TYPE_NAME("cortex-a8");
    mc->auto_create_sdcard = true;

    machine_add_audiodev_property(mc);
}

static const TypeInfo realview_pb_a8_type = {
    .name = MACHINE_TYPE_NAME("realview-pb-a8"),
    .parent = TYPE_MACHINE,
    .class_init = realview_pb_a8_class_init,
};

static void realview_pbx_a9_class_init(ObjectClass *oc, void *data)
{
    MachineClass *mc = MACHINE_CLASS(oc);

    mc->desc = "ARM RealView Platform Baseboard Explore for Cortex-A9";
    mc->init = realview_pbx_a9_init;
    mc->max_cpus = 4;
    mc->ignore_memory_transaction_failures = true;
    mc->default_cpu_type = ARM_CPU_TYPE_NAME("cortex-a9");
    mc->auto_create_sdcard = true;

    machine_add_audiodev_property(mc);
}

static const TypeInfo realview_pbx_a9_type = {
    .name = MACHINE_TYPE_NAME("realview-pbx-a9"),
    .parent = TYPE_MACHINE,
    .class_init = realview_pbx_a9_class_init,
};

static void realview_machine_init(void)
{
    type_register_static(&realview_eb_type);
    type_register_static(&realview_eb_mpcore_type);
    type_register_static(&realview_pb_a8_type);
    type_register_static(&realview_pbx_a9_type);
}

type_init(realview_machine_init)