1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Allwinner sun4i USB phy driver 4 * 5 * Copyright (C) 2014-2015 Hans de Goede <hdegoede@redhat.com> 6 * 7 * Based on code from 8 * Allwinner Technology Co., Ltd. <www.allwinnertech.com> 9 * 10 * Modelled after: Samsung S5P/Exynos SoC series MIPI CSIS/DSIM DPHY driver 11 * Copyright (C) 2013 Samsung Electronics Co., Ltd. 12 * Author: Sylwester Nawrocki <s.nawrocki@samsung.com> 13 */ 14 15 #include <linux/clk.h> 16 #include <linux/delay.h> 17 #include <linux/err.h> 18 #include <linux/extcon-provider.h> 19 #include <linux/gpio/consumer.h> 20 #include <linux/io.h> 21 #include <linux/interrupt.h> 22 #include <linux/kernel.h> 23 #include <linux/module.h> 24 #include <linux/mutex.h> 25 #include <linux/of.h> 26 #include <linux/phy/phy.h> 27 #include <linux/phy/phy-sun4i-usb.h> 28 #include <linux/platform_device.h> 29 #include <linux/power_supply.h> 30 #include <linux/regulator/consumer.h> 31 #include <linux/reset.h> 32 #include <linux/spinlock.h> 33 #include <linux/usb/of.h> 34 #include <linux/workqueue.h> 35 36 #define REG_ISCR 0x00 37 #define REG_PHYCTL_A10 0x04 38 #define REG_PHYBIST 0x08 39 #define REG_PHYTUNE 0x0c 40 #define REG_PHYCTL_A33 0x10 41 #define REG_PHY_OTGCTL 0x20 42 43 #define REG_HCI_PHY_CTL 0x10 44 45 #define PHYCTL_DATA BIT(7) 46 47 #define OTGCTL_ROUTE_MUSB BIT(0) 48 49 #define SUNXI_AHB_ICHR8_EN BIT(10) 50 #define SUNXI_AHB_INCR4_BURST_EN BIT(9) 51 #define SUNXI_AHB_INCRX_ALIGN_EN BIT(8) 52 #define SUNXI_ULPI_BYPASS_EN BIT(0) 53 54 /* ISCR, Interface Status and Control bits */ 55 #define ISCR_ID_PULLUP_EN (1 << 17) 56 #define ISCR_DPDM_PULLUP_EN (1 << 16) 57 /* sunxi has the phy id/vbus pins not connected, so we use the force bits */ 58 #define ISCR_FORCE_ID_MASK (3 << 14) 59 #define ISCR_FORCE_ID_LOW (2 << 14) 60 #define ISCR_FORCE_ID_HIGH (3 << 14) 61 #define ISCR_FORCE_VBUS_MASK (3 << 12) 62 #define ISCR_FORCE_VBUS_LOW (2 << 12) 63 #define ISCR_FORCE_VBUS_HIGH (3 << 12) 64 65 /* Common Control Bits for Both PHYs */ 66 #define PHY_PLL_BW 0x03 67 #define PHY_RES45_CAL_EN 0x0c 68 69 /* Private Control Bits for Each PHY */ 70 #define PHY_TX_AMPLITUDE_TUNE 0x20 71 #define PHY_TX_SLEWRATE_TUNE 0x22 72 #define PHY_VBUSVALID_TH_SEL 0x25 73 #define PHY_PULLUP_RES_SEL 0x27 74 #define PHY_OTG_FUNC_EN 0x28 75 #define PHY_VBUS_DET_EN 0x29 76 #define PHY_DISCON_TH_SEL 0x2a 77 #define PHY_SQUELCH_DETECT 0x3c 78 79 /* A83T specific control bits for PHY0 */ 80 #define PHY_CTL_VBUSVLDEXT BIT(5) 81 #define PHY_CTL_SIDDQ BIT(3) 82 #define PHY_CTL_H3_SIDDQ BIT(1) 83 84 /* A83T specific control bits for PHY2 HSIC */ 85 #define SUNXI_EHCI_HS_FORCE BIT(20) 86 #define SUNXI_HSIC_CONNECT_DET BIT(17) 87 #define SUNXI_HSIC_CONNECT_INT BIT(16) 88 #define SUNXI_HSIC BIT(1) 89 90 #define MAX_PHYS 4 91 92 /* 93 * Note do not raise the debounce time, we must report Vusb high within 100ms 94 * otherwise we get Vbus errors 95 */ 96 #define DEBOUNCE_TIME msecs_to_jiffies(50) 97 #define POLL_TIME msecs_to_jiffies(250) 98 99 struct sun4i_usb_phy_cfg { 100 int num_phys; 101 int hsic_index; 102 u32 disc_thresh; 103 u32 hci_phy_ctl_clear; 104 u8 phyctl_offset; 105 bool dedicated_clocks; 106 bool phy0_dual_route; 107 bool needs_phy2_siddq; 108 bool siddq_in_base; 109 bool poll_vbusen; 110 int missing_phys; 111 }; 112 113 struct sun4i_usb_phy_data { 114 void __iomem *base; 115 const struct sun4i_usb_phy_cfg *cfg; 116 enum usb_dr_mode dr_mode; 117 spinlock_t reg_lock; /* guard access to phyctl reg */ 118 struct sun4i_usb_phy { 119 struct phy *phy; 120 void __iomem *pmu; 121 struct regulator *vbus; 122 struct reset_control *reset; 123 struct clk *clk; 124 struct clk *clk2; 125 bool regulator_on; 126 int index; 127 } phys[MAX_PHYS]; 128 /* phy0 / otg related variables */ 129 struct extcon_dev *extcon; 130 bool phy0_init; 131 struct gpio_desc *id_det_gpio; 132 struct gpio_desc *vbus_det_gpio; 133 struct power_supply *vbus_power_supply; 134 struct notifier_block vbus_power_nb; 135 bool vbus_power_nb_registered; 136 bool force_session_end; 137 int id_det_irq; 138 int vbus_det_irq; 139 int id_det; 140 int vbus_det; 141 struct delayed_work detect; 142 }; 143 144 #define to_sun4i_usb_phy_data(phy) \ 145 container_of((phy), struct sun4i_usb_phy_data, phys[(phy)->index]) 146 147 static void sun4i_usb_phy0_update_iscr(struct phy *_phy, u32 clr, u32 set) 148 { 149 struct sun4i_usb_phy *phy = phy_get_drvdata(_phy); 150 struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy); 151 u32 iscr; 152 153 iscr = readl(data->base + REG_ISCR); 154 iscr &= ~clr; 155 iscr |= set; 156 writel(iscr, data->base + REG_ISCR); 157 } 158 159 static void sun4i_usb_phy0_set_id_detect(struct phy *phy, u32 val) 160 { 161 if (val) 162 val = ISCR_FORCE_ID_HIGH; 163 else 164 val = ISCR_FORCE_ID_LOW; 165 166 sun4i_usb_phy0_update_iscr(phy, ISCR_FORCE_ID_MASK, val); 167 } 168 169 static void sun4i_usb_phy0_set_vbus_detect(struct phy *phy, u32 val) 170 { 171 if (val) 172 val = ISCR_FORCE_VBUS_HIGH; 173 else 174 val = ISCR_FORCE_VBUS_LOW; 175 176 sun4i_usb_phy0_update_iscr(phy, ISCR_FORCE_VBUS_MASK, val); 177 } 178 179 static void sun4i_usb_phy_write(struct sun4i_usb_phy *phy, u32 addr, u32 data, 180 int len) 181 { 182 struct sun4i_usb_phy_data *phy_data = to_sun4i_usb_phy_data(phy); 183 u32 temp, usbc_bit = BIT(phy->index * 2); 184 void __iomem *phyctl = phy_data->base + phy_data->cfg->phyctl_offset; 185 unsigned long flags; 186 int i; 187 188 spin_lock_irqsave(&phy_data->reg_lock, flags); 189 190 if (phy_data->cfg->phyctl_offset == REG_PHYCTL_A33) { 191 /* SoCs newer than A33 need us to set phyctl to 0 explicitly */ 192 writel(0, phyctl); 193 } 194 195 for (i = 0; i < len; i++) { 196 temp = readl(phyctl); 197 198 /* clear the address portion */ 199 temp &= ~(0xff << 8); 200 201 /* set the address */ 202 temp |= ((addr + i) << 8); 203 writel(temp, phyctl); 204 205 /* set the data bit and clear usbc bit*/ 206 temp = readb(phyctl); 207 if (data & 0x1) 208 temp |= PHYCTL_DATA; 209 else 210 temp &= ~PHYCTL_DATA; 211 temp &= ~usbc_bit; 212 writeb(temp, phyctl); 213 214 /* pulse usbc_bit */ 215 temp = readb(phyctl); 216 temp |= usbc_bit; 217 writeb(temp, phyctl); 218 219 temp = readb(phyctl); 220 temp &= ~usbc_bit; 221 writeb(temp, phyctl); 222 223 data >>= 1; 224 } 225 226 spin_unlock_irqrestore(&phy_data->reg_lock, flags); 227 } 228 229 static void sun4i_usb_phy_passby(struct sun4i_usb_phy *phy, int enable) 230 { 231 struct sun4i_usb_phy_data *phy_data = to_sun4i_usb_phy_data(phy); 232 u32 bits, reg_value; 233 234 if (!phy->pmu) 235 return; 236 237 bits = SUNXI_AHB_ICHR8_EN | SUNXI_AHB_INCR4_BURST_EN | 238 SUNXI_AHB_INCRX_ALIGN_EN | SUNXI_ULPI_BYPASS_EN; 239 240 /* A83T USB2 is HSIC */ 241 if (phy_data->cfg->hsic_index && 242 phy->index == phy_data->cfg->hsic_index) 243 bits |= SUNXI_EHCI_HS_FORCE | SUNXI_HSIC_CONNECT_INT | 244 SUNXI_HSIC; 245 246 reg_value = readl(phy->pmu); 247 248 if (enable) 249 reg_value |= bits; 250 else 251 reg_value &= ~bits; 252 253 writel(reg_value, phy->pmu); 254 } 255 256 static int sun4i_usb_phy_init(struct phy *_phy) 257 { 258 struct sun4i_usb_phy *phy = phy_get_drvdata(_phy); 259 struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy); 260 int ret; 261 u32 val; 262 263 ret = clk_prepare_enable(phy->clk); 264 if (ret) 265 return ret; 266 267 ret = clk_prepare_enable(phy->clk2); 268 if (ret) { 269 clk_disable_unprepare(phy->clk); 270 return ret; 271 } 272 273 ret = reset_control_deassert(phy->reset); 274 if (ret) { 275 clk_disable_unprepare(phy->clk2); 276 clk_disable_unprepare(phy->clk); 277 return ret; 278 } 279 280 /* Some PHYs on some SoCs need the help of PHY2 to work. */ 281 if (data->cfg->needs_phy2_siddq && phy->index != 2) { 282 struct sun4i_usb_phy *phy2 = &data->phys[2]; 283 284 ret = clk_prepare_enable(phy2->clk); 285 if (ret) { 286 reset_control_assert(phy->reset); 287 clk_disable_unprepare(phy->clk2); 288 clk_disable_unprepare(phy->clk); 289 return ret; 290 } 291 292 ret = reset_control_deassert(phy2->reset); 293 if (ret) { 294 clk_disable_unprepare(phy2->clk); 295 reset_control_assert(phy->reset); 296 clk_disable_unprepare(phy->clk2); 297 clk_disable_unprepare(phy->clk); 298 return ret; 299 } 300 301 /* 302 * This extra clock is just needed to access the 303 * REG_HCI_PHY_CTL PMU register for PHY2. 304 */ 305 ret = clk_prepare_enable(phy2->clk2); 306 if (ret) { 307 reset_control_assert(phy2->reset); 308 clk_disable_unprepare(phy2->clk); 309 reset_control_assert(phy->reset); 310 clk_disable_unprepare(phy->clk2); 311 clk_disable_unprepare(phy->clk); 312 return ret; 313 } 314 315 if (phy2->pmu && data->cfg->hci_phy_ctl_clear) { 316 val = readl(phy2->pmu + REG_HCI_PHY_CTL); 317 val &= ~data->cfg->hci_phy_ctl_clear; 318 writel(val, phy2->pmu + REG_HCI_PHY_CTL); 319 } 320 321 clk_disable_unprepare(phy->clk2); 322 } 323 324 if (phy->pmu && data->cfg->hci_phy_ctl_clear) { 325 val = readl(phy->pmu + REG_HCI_PHY_CTL); 326 val &= ~data->cfg->hci_phy_ctl_clear; 327 writel(val, phy->pmu + REG_HCI_PHY_CTL); 328 } 329 330 if (data->cfg->siddq_in_base) { 331 if (phy->index == 0) { 332 val = readl(data->base + data->cfg->phyctl_offset); 333 val |= PHY_CTL_VBUSVLDEXT; 334 val &= ~PHY_CTL_SIDDQ; 335 writel(val, data->base + data->cfg->phyctl_offset); 336 } 337 } else { 338 /* Enable USB 45 Ohm resistor calibration */ 339 if (phy->index == 0) 340 sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1); 341 342 /* Adjust PHY's magnitude and rate */ 343 sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE, 0x14, 5); 344 345 /* Disconnect threshold adjustment */ 346 sun4i_usb_phy_write(phy, PHY_DISCON_TH_SEL, 347 data->cfg->disc_thresh, 2); 348 } 349 350 sun4i_usb_phy_passby(phy, 1); 351 352 if (phy->index == 0) { 353 data->phy0_init = true; 354 355 /* Enable pull-ups */ 356 sun4i_usb_phy0_update_iscr(_phy, 0, ISCR_DPDM_PULLUP_EN); 357 sun4i_usb_phy0_update_iscr(_phy, 0, ISCR_ID_PULLUP_EN); 358 359 /* Force ISCR and cable state updates */ 360 data->id_det = -1; 361 data->vbus_det = -1; 362 queue_delayed_work(system_wq, &data->detect, 0); 363 } 364 365 return 0; 366 } 367 368 static int sun4i_usb_phy_exit(struct phy *_phy) 369 { 370 struct sun4i_usb_phy *phy = phy_get_drvdata(_phy); 371 struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy); 372 373 if (phy->index == 0) { 374 if (data->cfg->siddq_in_base) { 375 void __iomem *phyctl = data->base + 376 data->cfg->phyctl_offset; 377 378 writel(readl(phyctl) | PHY_CTL_SIDDQ, phyctl); 379 } 380 381 /* Disable pull-ups */ 382 sun4i_usb_phy0_update_iscr(_phy, ISCR_DPDM_PULLUP_EN, 0); 383 sun4i_usb_phy0_update_iscr(_phy, ISCR_ID_PULLUP_EN, 0); 384 data->phy0_init = false; 385 } 386 387 if (data->cfg->needs_phy2_siddq && phy->index != 2) { 388 struct sun4i_usb_phy *phy2 = &data->phys[2]; 389 390 clk_disable_unprepare(phy2->clk); 391 reset_control_assert(phy2->reset); 392 } 393 394 sun4i_usb_phy_passby(phy, 0); 395 reset_control_assert(phy->reset); 396 clk_disable_unprepare(phy->clk2); 397 clk_disable_unprepare(phy->clk); 398 399 return 0; 400 } 401 402 static int sun4i_usb_phy0_get_id_det(struct sun4i_usb_phy_data *data) 403 { 404 switch (data->dr_mode) { 405 case USB_DR_MODE_OTG: 406 if (data->id_det_gpio) 407 return gpiod_get_value_cansleep(data->id_det_gpio); 408 else 409 return 1; /* Fallback to peripheral mode */ 410 case USB_DR_MODE_HOST: 411 return 0; 412 case USB_DR_MODE_PERIPHERAL: 413 default: 414 return 1; 415 } 416 } 417 418 static int sun4i_usb_phy0_get_vbus_det(struct sun4i_usb_phy_data *data) 419 { 420 if (data->vbus_det_gpio) 421 return gpiod_get_value_cansleep(data->vbus_det_gpio); 422 423 if (data->vbus_power_supply) { 424 union power_supply_propval val; 425 int r; 426 427 r = power_supply_get_property(data->vbus_power_supply, 428 POWER_SUPPLY_PROP_PRESENT, &val); 429 if (r == 0) 430 return val.intval; 431 } 432 433 /* Fallback: report vbus as high */ 434 return 1; 435 } 436 437 static bool sun4i_usb_phy0_have_vbus_det(struct sun4i_usb_phy_data *data) 438 { 439 return data->vbus_det_gpio || data->vbus_power_supply; 440 } 441 442 static bool sun4i_usb_phy0_poll(struct sun4i_usb_phy_data *data) 443 { 444 if ((data->id_det_gpio && data->id_det_irq <= 0) || 445 (data->vbus_det_gpio && data->vbus_det_irq <= 0)) 446 return true; 447 448 /* 449 * The A31/A23/A33 companion pmics (AXP221/AXP223) do not 450 * generate vbus change interrupts when the board is driving 451 * vbus using the N_VBUSEN pin on the pmic, so we must poll 452 * when using the pmic for vbus-det _and_ we're driving vbus. 453 */ 454 if (data->cfg->poll_vbusen && data->vbus_power_supply && 455 data->phys[0].regulator_on) 456 return true; 457 458 return false; 459 } 460 461 static int sun4i_usb_phy_power_on(struct phy *_phy) 462 { 463 struct sun4i_usb_phy *phy = phy_get_drvdata(_phy); 464 struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy); 465 int ret; 466 467 if (!phy->vbus || phy->regulator_on) 468 return 0; 469 470 /* For phy0 only turn on Vbus if we don't have an ext. Vbus */ 471 if (phy->index == 0 && sun4i_usb_phy0_have_vbus_det(data) && 472 data->vbus_det) { 473 dev_warn(&_phy->dev, "External vbus detected, not enabling our own vbus\n"); 474 return 0; 475 } 476 477 ret = regulator_enable(phy->vbus); 478 if (ret) 479 return ret; 480 481 phy->regulator_on = true; 482 483 /* We must report Vbus high within OTG_TIME_A_WAIT_VRISE msec. */ 484 if (phy->index == 0 && sun4i_usb_phy0_poll(data)) 485 mod_delayed_work(system_wq, &data->detect, DEBOUNCE_TIME); 486 487 return 0; 488 } 489 490 static int sun4i_usb_phy_power_off(struct phy *_phy) 491 { 492 struct sun4i_usb_phy *phy = phy_get_drvdata(_phy); 493 struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy); 494 495 if (!phy->vbus || !phy->regulator_on) 496 return 0; 497 498 regulator_disable(phy->vbus); 499 phy->regulator_on = false; 500 501 /* 502 * phy0 vbus typically slowly discharges, sometimes this causes the 503 * Vbus gpio to not trigger an edge irq on Vbus off, so force a rescan. 504 */ 505 if (phy->index == 0 && !sun4i_usb_phy0_poll(data)) 506 mod_delayed_work(system_wq, &data->detect, POLL_TIME); 507 508 return 0; 509 } 510 511 static int sun4i_usb_phy_set_mode(struct phy *_phy, 512 enum phy_mode mode, int submode) 513 { 514 struct sun4i_usb_phy *phy = phy_get_drvdata(_phy); 515 struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy); 516 int new_mode; 517 518 if (phy->index != 0) { 519 if (mode == PHY_MODE_USB_HOST) 520 return 0; 521 return -EINVAL; 522 } 523 524 switch (mode) { 525 case PHY_MODE_USB_HOST: 526 new_mode = USB_DR_MODE_HOST; 527 break; 528 case PHY_MODE_USB_DEVICE: 529 new_mode = USB_DR_MODE_PERIPHERAL; 530 break; 531 case PHY_MODE_USB_OTG: 532 new_mode = USB_DR_MODE_OTG; 533 break; 534 default: 535 return -EINVAL; 536 } 537 538 if (new_mode != data->dr_mode) { 539 dev_info(&_phy->dev, "Changing dr_mode to %d\n", new_mode); 540 data->dr_mode = new_mode; 541 } 542 543 data->id_det = -1; /* Force reprocessing of id */ 544 data->force_session_end = true; 545 queue_delayed_work(system_wq, &data->detect, 0); 546 547 return 0; 548 } 549 550 void sun4i_usb_phy_set_squelch_detect(struct phy *_phy, bool enabled) 551 { 552 struct sun4i_usb_phy *phy = phy_get_drvdata(_phy); 553 554 sun4i_usb_phy_write(phy, PHY_SQUELCH_DETECT, enabled ? 0 : 2, 2); 555 } 556 EXPORT_SYMBOL_GPL(sun4i_usb_phy_set_squelch_detect); 557 558 static const struct phy_ops sun4i_usb_phy_ops = { 559 .init = sun4i_usb_phy_init, 560 .exit = sun4i_usb_phy_exit, 561 .power_on = sun4i_usb_phy_power_on, 562 .power_off = sun4i_usb_phy_power_off, 563 .set_mode = sun4i_usb_phy_set_mode, 564 .owner = THIS_MODULE, 565 }; 566 567 static void sun4i_usb_phy0_reroute(struct sun4i_usb_phy_data *data, int id_det) 568 { 569 u32 regval; 570 571 regval = readl(data->base + REG_PHY_OTGCTL); 572 if (id_det == 0) { 573 /* Host mode. Route phy0 to EHCI/OHCI */ 574 regval &= ~OTGCTL_ROUTE_MUSB; 575 } else { 576 /* Peripheral mode. Route phy0 to MUSB */ 577 regval |= OTGCTL_ROUTE_MUSB; 578 } 579 writel(regval, data->base + REG_PHY_OTGCTL); 580 } 581 582 static void sun4i_usb_phy0_id_vbus_det_scan(struct work_struct *work) 583 { 584 struct sun4i_usb_phy_data *data = 585 container_of(work, struct sun4i_usb_phy_data, detect.work); 586 struct phy *phy0 = data->phys[0].phy; 587 struct sun4i_usb_phy *phy; 588 bool force_session_end, id_notify = false, vbus_notify = false; 589 int id_det, vbus_det; 590 591 if (!phy0) 592 return; 593 594 phy = phy_get_drvdata(phy0); 595 id_det = sun4i_usb_phy0_get_id_det(data); 596 vbus_det = sun4i_usb_phy0_get_vbus_det(data); 597 598 mutex_lock(&phy0->mutex); 599 600 if (!data->phy0_init) { 601 mutex_unlock(&phy0->mutex); 602 return; 603 } 604 605 force_session_end = data->force_session_end; 606 data->force_session_end = false; 607 608 if (id_det != data->id_det) { 609 /* id-change, force session end if we've no vbus detection */ 610 if (data->dr_mode == USB_DR_MODE_OTG && 611 !sun4i_usb_phy0_have_vbus_det(data)) 612 force_session_end = true; 613 614 /* When entering host mode (id = 0) force end the session now */ 615 if (force_session_end && id_det == 0) { 616 sun4i_usb_phy0_set_vbus_detect(phy0, 0); 617 msleep(200); 618 sun4i_usb_phy0_set_vbus_detect(phy0, 1); 619 } 620 sun4i_usb_phy0_set_id_detect(phy0, id_det); 621 data->id_det = id_det; 622 id_notify = true; 623 } 624 625 if (vbus_det != data->vbus_det) { 626 sun4i_usb_phy0_set_vbus_detect(phy0, vbus_det); 627 data->vbus_det = vbus_det; 628 vbus_notify = true; 629 } 630 631 mutex_unlock(&phy0->mutex); 632 633 if (id_notify) { 634 extcon_set_state_sync(data->extcon, EXTCON_USB_HOST, 635 !id_det); 636 /* When leaving host mode force end the session here */ 637 if (force_session_end && id_det == 1) { 638 mutex_lock(&phy0->mutex); 639 sun4i_usb_phy0_set_vbus_detect(phy0, 0); 640 msleep(1000); 641 sun4i_usb_phy0_set_vbus_detect(phy0, 1); 642 mutex_unlock(&phy0->mutex); 643 } 644 645 /* Enable PHY0 passby for host mode only. */ 646 sun4i_usb_phy_passby(phy, !id_det); 647 648 /* Re-route PHY0 if necessary */ 649 if (data->cfg->phy0_dual_route) 650 sun4i_usb_phy0_reroute(data, id_det); 651 } 652 653 if (vbus_notify) 654 extcon_set_state_sync(data->extcon, EXTCON_USB, vbus_det); 655 656 if (sun4i_usb_phy0_poll(data)) 657 queue_delayed_work(system_wq, &data->detect, POLL_TIME); 658 } 659 660 static irqreturn_t sun4i_usb_phy0_id_vbus_det_irq(int irq, void *dev_id) 661 { 662 struct sun4i_usb_phy_data *data = dev_id; 663 664 /* vbus or id changed, let the pins settle and then scan them */ 665 mod_delayed_work(system_wq, &data->detect, DEBOUNCE_TIME); 666 667 return IRQ_HANDLED; 668 } 669 670 static int sun4i_usb_phy0_vbus_notify(struct notifier_block *nb, 671 unsigned long val, void *v) 672 { 673 struct sun4i_usb_phy_data *data = 674 container_of(nb, struct sun4i_usb_phy_data, vbus_power_nb); 675 struct power_supply *psy = v; 676 677 /* Properties on the vbus_power_supply changed, scan vbus_det */ 678 if (val == PSY_EVENT_PROP_CHANGED && psy == data->vbus_power_supply) 679 mod_delayed_work(system_wq, &data->detect, DEBOUNCE_TIME); 680 681 return NOTIFY_OK; 682 } 683 684 static struct phy *sun4i_usb_phy_xlate(struct device *dev, 685 const struct of_phandle_args *args) 686 { 687 struct sun4i_usb_phy_data *data = dev_get_drvdata(dev); 688 689 if (args->args[0] >= data->cfg->num_phys) 690 return ERR_PTR(-ENODEV); 691 692 if (data->cfg->missing_phys & BIT(args->args[0])) 693 return ERR_PTR(-ENODEV); 694 695 return data->phys[args->args[0]].phy; 696 } 697 698 static void sun4i_usb_phy_remove(struct platform_device *pdev) 699 { 700 struct device *dev = &pdev->dev; 701 struct sun4i_usb_phy_data *data = dev_get_drvdata(dev); 702 703 if (data->vbus_power_nb_registered) 704 power_supply_unreg_notifier(&data->vbus_power_nb); 705 if (data->id_det_irq > 0) 706 devm_free_irq(dev, data->id_det_irq, data); 707 if (data->vbus_det_irq > 0) 708 devm_free_irq(dev, data->vbus_det_irq, data); 709 710 cancel_delayed_work_sync(&data->detect); 711 } 712 713 static const unsigned int sun4i_usb_phy0_cable[] = { 714 EXTCON_USB, 715 EXTCON_USB_HOST, 716 EXTCON_NONE, 717 }; 718 719 static int sun4i_usb_phy_probe(struct platform_device *pdev) 720 { 721 struct sun4i_usb_phy_data *data; 722 struct device *dev = &pdev->dev; 723 struct device_node *np = dev->of_node; 724 struct phy_provider *phy_provider; 725 int i, ret; 726 727 data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL); 728 if (!data) 729 return -ENOMEM; 730 731 spin_lock_init(&data->reg_lock); 732 INIT_DELAYED_WORK(&data->detect, sun4i_usb_phy0_id_vbus_det_scan); 733 dev_set_drvdata(dev, data); 734 data->cfg = of_device_get_match_data(dev); 735 if (!data->cfg) 736 return -EINVAL; 737 738 data->base = devm_platform_ioremap_resource_byname(pdev, "phy_ctrl"); 739 if (IS_ERR(data->base)) 740 return PTR_ERR(data->base); 741 742 data->id_det_gpio = devm_gpiod_get_optional(dev, "usb0_id_det", 743 GPIOD_IN); 744 if (IS_ERR(data->id_det_gpio)) { 745 dev_err(dev, "Couldn't request ID GPIO\n"); 746 return PTR_ERR(data->id_det_gpio); 747 } 748 749 data->vbus_det_gpio = devm_gpiod_get_optional(dev, "usb0_vbus_det", 750 GPIOD_IN); 751 if (IS_ERR(data->vbus_det_gpio)) { 752 dev_err(dev, "Couldn't request VBUS detect GPIO\n"); 753 return PTR_ERR(data->vbus_det_gpio); 754 } 755 756 if (of_property_present(np, "usb0_vbus_power-supply")) { 757 data->vbus_power_supply = devm_power_supply_get_by_phandle(dev, 758 "usb0_vbus_power-supply"); 759 if (IS_ERR(data->vbus_power_supply)) { 760 dev_err(dev, "Couldn't get the VBUS power supply\n"); 761 return PTR_ERR(data->vbus_power_supply); 762 } 763 764 if (!data->vbus_power_supply) 765 return -EPROBE_DEFER; 766 } 767 768 data->dr_mode = of_usb_get_dr_mode_by_phy(np, 0); 769 770 data->extcon = devm_extcon_dev_allocate(dev, sun4i_usb_phy0_cable); 771 if (IS_ERR(data->extcon)) { 772 dev_err(dev, "Couldn't allocate our extcon device\n"); 773 return PTR_ERR(data->extcon); 774 } 775 776 ret = devm_extcon_dev_register(dev, data->extcon); 777 if (ret) { 778 dev_err(dev, "failed to register extcon: %d\n", ret); 779 return ret; 780 } 781 782 for (i = 0; i < data->cfg->num_phys; i++) { 783 struct sun4i_usb_phy *phy = data->phys + i; 784 char name[32]; 785 786 if (data->cfg->missing_phys & BIT(i)) 787 continue; 788 789 snprintf(name, sizeof(name), "usb%d_vbus", i); 790 phy->vbus = devm_regulator_get_optional(dev, name); 791 if (IS_ERR(phy->vbus)) { 792 if (PTR_ERR(phy->vbus) == -EPROBE_DEFER) { 793 dev_err(dev, 794 "Couldn't get regulator %s... Deferring probe\n", 795 name); 796 return -EPROBE_DEFER; 797 } 798 799 phy->vbus = NULL; 800 } 801 802 if (data->cfg->dedicated_clocks) 803 snprintf(name, sizeof(name), "usb%d_phy", i); 804 else 805 strscpy(name, "usb_phy", sizeof(name)); 806 807 phy->clk = devm_clk_get(dev, name); 808 if (IS_ERR(phy->clk)) { 809 dev_err(dev, "failed to get clock %s\n", name); 810 return PTR_ERR(phy->clk); 811 } 812 813 /* The first PHY is always tied to OTG, and never HSIC */ 814 if (data->cfg->hsic_index && i == data->cfg->hsic_index) { 815 /* HSIC needs secondary clock */ 816 snprintf(name, sizeof(name), "usb%d_hsic_12M", i); 817 phy->clk2 = devm_clk_get(dev, name); 818 if (IS_ERR(phy->clk2)) { 819 dev_err(dev, "failed to get clock %s\n", name); 820 return PTR_ERR(phy->clk2); 821 } 822 } else { 823 snprintf(name, sizeof(name), "pmu%d_clk", i); 824 phy->clk2 = devm_clk_get_optional(dev, name); 825 if (IS_ERR(phy->clk2)) { 826 dev_err(dev, "failed to get clock %s\n", name); 827 return PTR_ERR(phy->clk2); 828 } 829 } 830 831 snprintf(name, sizeof(name), "usb%d_reset", i); 832 phy->reset = devm_reset_control_get(dev, name); 833 if (IS_ERR(phy->reset)) { 834 dev_err(dev, "failed to get reset %s\n", name); 835 return PTR_ERR(phy->reset); 836 } 837 838 if (i || data->cfg->phy0_dual_route) { /* No pmu for musb */ 839 snprintf(name, sizeof(name), "pmu%d", i); 840 phy->pmu = devm_platform_ioremap_resource_byname(pdev, name); 841 if (IS_ERR(phy->pmu)) 842 return PTR_ERR(phy->pmu); 843 } 844 845 phy->phy = devm_phy_create(dev, NULL, &sun4i_usb_phy_ops); 846 if (IS_ERR(phy->phy)) { 847 dev_err(dev, "failed to create PHY %d\n", i); 848 return PTR_ERR(phy->phy); 849 } 850 851 phy->index = i; 852 phy_set_drvdata(phy->phy, &data->phys[i]); 853 } 854 855 data->id_det_irq = gpiod_to_irq(data->id_det_gpio); 856 if (data->id_det_irq > 0) { 857 ret = devm_request_irq(dev, data->id_det_irq, 858 sun4i_usb_phy0_id_vbus_det_irq, 859 IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, 860 "usb0-id-det", data); 861 if (ret) { 862 dev_err(dev, "Err requesting id-det-irq: %d\n", ret); 863 return ret; 864 } 865 } 866 867 data->vbus_det_irq = gpiod_to_irq(data->vbus_det_gpio); 868 if (data->vbus_det_irq > 0) { 869 ret = devm_request_irq(dev, data->vbus_det_irq, 870 sun4i_usb_phy0_id_vbus_det_irq, 871 IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, 872 "usb0-vbus-det", data); 873 if (ret) { 874 dev_err(dev, "Err requesting vbus-det-irq: %d\n", ret); 875 data->vbus_det_irq = -1; 876 sun4i_usb_phy_remove(pdev); /* Stop detect work */ 877 return ret; 878 } 879 } 880 881 if (data->vbus_power_supply) { 882 data->vbus_power_nb.notifier_call = sun4i_usb_phy0_vbus_notify; 883 data->vbus_power_nb.priority = 0; 884 ret = power_supply_reg_notifier(&data->vbus_power_nb); 885 if (ret) { 886 sun4i_usb_phy_remove(pdev); /* Stop detect work */ 887 return ret; 888 } 889 data->vbus_power_nb_registered = true; 890 } 891 892 phy_provider = devm_of_phy_provider_register(dev, sun4i_usb_phy_xlate); 893 if (IS_ERR(phy_provider)) { 894 sun4i_usb_phy_remove(pdev); /* Stop detect work */ 895 return PTR_ERR(phy_provider); 896 } 897 898 dev_dbg(dev, "successfully loaded\n"); 899 900 return 0; 901 } 902 903 static const struct sun4i_usb_phy_cfg suniv_f1c100s_cfg = { 904 .num_phys = 1, 905 .disc_thresh = 3, 906 .phyctl_offset = REG_PHYCTL_A10, 907 .dedicated_clocks = true, 908 }; 909 910 static const struct sun4i_usb_phy_cfg sun4i_a10_cfg = { 911 .num_phys = 3, 912 .disc_thresh = 3, 913 .phyctl_offset = REG_PHYCTL_A10, 914 .dedicated_clocks = false, 915 }; 916 917 static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = { 918 .num_phys = 2, 919 .disc_thresh = 2, 920 .phyctl_offset = REG_PHYCTL_A10, 921 .dedicated_clocks = false, 922 }; 923 924 static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = { 925 .num_phys = 3, 926 .disc_thresh = 3, 927 .phyctl_offset = REG_PHYCTL_A10, 928 .dedicated_clocks = true, 929 .poll_vbusen = true, 930 }; 931 932 static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = { 933 .num_phys = 3, 934 .disc_thresh = 2, 935 .phyctl_offset = REG_PHYCTL_A10, 936 .dedicated_clocks = false, 937 }; 938 939 static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = { 940 .num_phys = 2, 941 .disc_thresh = 3, 942 .phyctl_offset = REG_PHYCTL_A10, 943 .dedicated_clocks = true, 944 .poll_vbusen = true, 945 }; 946 947 static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = { 948 .num_phys = 2, 949 .disc_thresh = 3, 950 .phyctl_offset = REG_PHYCTL_A33, 951 .dedicated_clocks = true, 952 .poll_vbusen = true, 953 }; 954 955 static const struct sun4i_usb_phy_cfg sun8i_a83t_cfg = { 956 .num_phys = 3, 957 .hsic_index = 2, 958 .phyctl_offset = REG_PHYCTL_A33, 959 .dedicated_clocks = true, 960 .siddq_in_base = true, 961 }; 962 963 static const struct sun4i_usb_phy_cfg sun8i_h3_cfg = { 964 .num_phys = 4, 965 .disc_thresh = 3, 966 .phyctl_offset = REG_PHYCTL_A33, 967 .dedicated_clocks = true, 968 .hci_phy_ctl_clear = PHY_CTL_H3_SIDDQ, 969 .phy0_dual_route = true, 970 }; 971 972 static const struct sun4i_usb_phy_cfg sun8i_r40_cfg = { 973 .num_phys = 3, 974 .disc_thresh = 3, 975 .phyctl_offset = REG_PHYCTL_A33, 976 .dedicated_clocks = true, 977 .hci_phy_ctl_clear = PHY_CTL_H3_SIDDQ, 978 .phy0_dual_route = true, 979 }; 980 981 static const struct sun4i_usb_phy_cfg sun8i_v3s_cfg = { 982 .num_phys = 1, 983 .disc_thresh = 3, 984 .phyctl_offset = REG_PHYCTL_A33, 985 .dedicated_clocks = true, 986 .hci_phy_ctl_clear = PHY_CTL_H3_SIDDQ, 987 .phy0_dual_route = true, 988 }; 989 990 static const struct sun4i_usb_phy_cfg sun20i_d1_cfg = { 991 .num_phys = 2, 992 .phyctl_offset = REG_PHYCTL_A33, 993 .dedicated_clocks = true, 994 .hci_phy_ctl_clear = PHY_CTL_SIDDQ, 995 .phy0_dual_route = true, 996 .siddq_in_base = true, 997 }; 998 999 static const struct sun4i_usb_phy_cfg sun50i_a64_cfg = { 1000 .num_phys = 2, 1001 .disc_thresh = 3, 1002 .phyctl_offset = REG_PHYCTL_A33, 1003 .dedicated_clocks = true, 1004 .hci_phy_ctl_clear = PHY_CTL_H3_SIDDQ, 1005 .phy0_dual_route = true, 1006 }; 1007 1008 static const struct sun4i_usb_phy_cfg sun50i_h6_cfg = { 1009 .num_phys = 4, 1010 .phyctl_offset = REG_PHYCTL_A33, 1011 .dedicated_clocks = true, 1012 .phy0_dual_route = true, 1013 .missing_phys = BIT(1) | BIT(2), 1014 .siddq_in_base = true, 1015 }; 1016 1017 static const struct sun4i_usb_phy_cfg sun50i_h616_cfg = { 1018 .num_phys = 4, 1019 .disc_thresh = 3, 1020 .phyctl_offset = REG_PHYCTL_A33, 1021 .dedicated_clocks = true, 1022 .phy0_dual_route = true, 1023 .hci_phy_ctl_clear = PHY_CTL_SIDDQ, 1024 .needs_phy2_siddq = true, 1025 .siddq_in_base = true, 1026 }; 1027 1028 static const struct of_device_id sun4i_usb_phy_of_match[] = { 1029 { .compatible = "allwinner,sun4i-a10-usb-phy", .data = &sun4i_a10_cfg }, 1030 { .compatible = "allwinner,sun5i-a13-usb-phy", .data = &sun5i_a13_cfg }, 1031 { .compatible = "allwinner,sun6i-a31-usb-phy", .data = &sun6i_a31_cfg }, 1032 { .compatible = "allwinner,sun7i-a20-usb-phy", .data = &sun7i_a20_cfg }, 1033 { .compatible = "allwinner,sun8i-a23-usb-phy", .data = &sun8i_a23_cfg }, 1034 { .compatible = "allwinner,sun8i-a33-usb-phy", .data = &sun8i_a33_cfg }, 1035 { .compatible = "allwinner,sun8i-a83t-usb-phy", .data = &sun8i_a83t_cfg }, 1036 { .compatible = "allwinner,sun8i-h3-usb-phy", .data = &sun8i_h3_cfg }, 1037 { .compatible = "allwinner,sun8i-r40-usb-phy", .data = &sun8i_r40_cfg }, 1038 { .compatible = "allwinner,sun8i-v3s-usb-phy", .data = &sun8i_v3s_cfg }, 1039 { .compatible = "allwinner,sun20i-d1-usb-phy", .data = &sun20i_d1_cfg }, 1040 { .compatible = "allwinner,sun50i-a64-usb-phy", 1041 .data = &sun50i_a64_cfg}, 1042 { .compatible = "allwinner,sun50i-h6-usb-phy", .data = &sun50i_h6_cfg }, 1043 { .compatible = "allwinner,sun50i-h616-usb-phy", .data = &sun50i_h616_cfg }, 1044 { .compatible = "allwinner,suniv-f1c100s-usb-phy", 1045 .data = &suniv_f1c100s_cfg }, 1046 { }, 1047 }; 1048 MODULE_DEVICE_TABLE(of, sun4i_usb_phy_of_match); 1049 1050 static struct platform_driver sun4i_usb_phy_driver = { 1051 .probe = sun4i_usb_phy_probe, 1052 .remove = sun4i_usb_phy_remove, 1053 .driver = { 1054 .of_match_table= sun4i_usb_phy_of_match, 1055 .name = "sun4i-usb-phy", 1056 } 1057 }; 1058 module_platform_driver(sun4i_usb_phy_driver); 1059 1060 MODULE_DESCRIPTION("Allwinner sun4i USB phy driver"); 1061 MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>"); 1062 MODULE_LICENSE("GPL v2"); 1063