1// SPDX-License-Identifier: GPL-2.0 2/* 3 * SDM845 MTP board device tree source 4 * 5 * Copyright (c) 2018, The Linux Foundation. All rights reserved. 6 */ 7 8/dts-v1/; 9 10#include <dt-bindings/regulator/qcom,rpmh-regulator.h> 11#include "sdm845.dtsi" 12#include "pm8998.dtsi" 13#include "pmi8998.dtsi" 14 15/ { 16 model = "Qualcomm Technologies, Inc. SDM845 MTP"; 17 compatible = "qcom,sdm845-mtp", "qcom,sdm845"; 18 chassis-type = "handset"; 19 20 aliases { 21 serial0 = &uart9; 22 }; 23 24 chosen { 25 stdout-path = "serial0:115200n8"; 26 }; 27 28 vph_pwr: vph-pwr-regulator { 29 compatible = "regulator-fixed"; 30 regulator-name = "vph_pwr"; 31 regulator-min-microvolt = <3700000>; 32 regulator-max-microvolt = <3700000>; 33 }; 34 35 /* 36 * Apparently RPMh does not provide support for PM8998 S4 because it 37 * is always-on; model it as a fixed regulator. 38 */ 39 vreg_s4a_1p8: pm8998-smps4 { 40 compatible = "regulator-fixed"; 41 regulator-name = "vreg_s4a_1p8"; 42 43 regulator-min-microvolt = <1800000>; 44 regulator-max-microvolt = <1800000>; 45 46 regulator-always-on; 47 regulator-boot-on; 48 49 vin-supply = <&vph_pwr>; 50 }; 51 52 thermal-zones { 53 xo_thermal: xo-thermal { 54 thermal-sensors = <&pm8998_adc_tm 1>; 55 56 trips { 57 trip-point { 58 temperature = <125000>; 59 hysteresis = <10000>; 60 type = "passive"; 61 }; 62 }; 63 }; 64 65 msm_thermal: msm-thermal { 66 thermal-sensors = <&pm8998_adc_tm 2>; 67 68 trips { 69 trip-point { 70 temperature = <125000>; 71 hysteresis = <10000>; 72 type = "passive"; 73 }; 74 }; 75 }; 76 77 pa_thermal: pa-thermal { 78 thermal-sensors = <&pm8998_adc_tm 3>; 79 80 trips { 81 trip-point { 82 temperature = <125000>; 83 hysteresis = <10000>; 84 type = "passive"; 85 }; 86 }; 87 }; 88 89 quiet_thermal: quiet-thermal { 90 thermal-sensors = <&pm8998_adc_tm 4>; 91 92 trips { 93 trip-point { 94 temperature = <125000>; 95 hysteresis = <10000>; 96 type = "passive"; 97 }; 98 }; 99 }; 100 }; 101}; 102 103&adsp_pas { 104 status = "okay"; 105 firmware-name = "qcom/sdm845/adsp.mbn"; 106}; 107 108&apps_rsc { 109 regulators-0 { 110 compatible = "qcom,pm8998-rpmh-regulators"; 111 qcom,pmic-id = "a"; 112 113 vdd-s1-supply = <&vph_pwr>; 114 vdd-s2-supply = <&vph_pwr>; 115 vdd-s3-supply = <&vph_pwr>; 116 vdd-s4-supply = <&vph_pwr>; 117 vdd-s5-supply = <&vph_pwr>; 118 vdd-s6-supply = <&vph_pwr>; 119 vdd-s7-supply = <&vph_pwr>; 120 vdd-s8-supply = <&vph_pwr>; 121 vdd-s9-supply = <&vph_pwr>; 122 vdd-s10-supply = <&vph_pwr>; 123 vdd-s11-supply = <&vph_pwr>; 124 vdd-s12-supply = <&vph_pwr>; 125 vdd-s13-supply = <&vph_pwr>; 126 vdd-l1-l27-supply = <&vreg_s7a_1p025>; 127 vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>; 128 vdd-l3-l11-supply = <&vreg_s7a_1p025>; 129 vdd-l4-l5-supply = <&vreg_s7a_1p025>; 130 vdd-l6-supply = <&vph_pwr>; 131 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>; 132 vdd-l9-supply = <&vreg_bob>; 133 vdd-l10-l23-l25-supply = <&vreg_bob>; 134 vdd-l13-l19-l21-supply = <&vreg_bob>; 135 vdd-l16-l28-supply = <&vreg_bob>; 136 vdd-l18-l22-supply = <&vreg_bob>; 137 vdd-l20-l24-supply = <&vreg_bob>; 138 vdd-l26-supply = <&vreg_s3a_1p35>; 139 vin-lvs-1-2-supply = <&vreg_s4a_1p8>; 140 141 vreg_s2a_1p125: smps2 { 142 regulator-min-microvolt = <1100000>; 143 regulator-max-microvolt = <1100000>; 144 }; 145 146 vreg_s3a_1p35: smps3 { 147 regulator-min-microvolt = <1352000>; 148 regulator-max-microvolt = <1352000>; 149 }; 150 151 vreg_s5a_2p04: smps5 { 152 regulator-min-microvolt = <1904000>; 153 regulator-max-microvolt = <2040000>; 154 }; 155 156 vreg_s7a_1p025: smps7 { 157 regulator-min-microvolt = <900000>; 158 regulator-max-microvolt = <1028000>; 159 }; 160 161 vdd_qusb_hs0: 162 vdda_hp_pcie_core: 163 vdda_mipi_csi0_0p9: 164 vdda_mipi_csi1_0p9: 165 vdda_mipi_csi2_0p9: 166 vdda_mipi_dsi0_pll: 167 vdda_mipi_dsi1_pll: 168 vdda_qlink_lv: 169 vdda_qlink_lv_ck: 170 vdda_qrefs_0p875: 171 vdda_pcie_core: 172 vdda_pll_cc_ebi01: 173 vdda_pll_cc_ebi23: 174 vdda_sp_sensor: 175 vdda_ufs1_core: 176 vdda_ufs2_core: 177 vdda_usb1_ss_core: 178 vdda_usb2_ss_core: 179 vreg_l1a_0p875: ldo1 { 180 regulator-min-microvolt = <880000>; 181 regulator-max-microvolt = <880000>; 182 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 183 }; 184 185 vddpx_10: 186 vreg_l2a_1p2: ldo2 { 187 regulator-min-microvolt = <1200000>; 188 regulator-max-microvolt = <1200000>; 189 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 190 regulator-always-on; 191 }; 192 193 vreg_l3a_1p0: ldo3 { 194 regulator-min-microvolt = <1000000>; 195 regulator-max-microvolt = <1000000>; 196 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 197 }; 198 199 vdd_wcss_cx: 200 vdd_wcss_mx: 201 vdda_wcss_pll: 202 vreg_l5a_0p8: ldo5 { 203 regulator-min-microvolt = <800000>; 204 regulator-max-microvolt = <800000>; 205 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 206 }; 207 208 vddpx_13: 209 vreg_l6a_1p8: ldo6 { 210 regulator-min-microvolt = <1856000>; 211 regulator-max-microvolt = <1856000>; 212 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 213 }; 214 215 vreg_l7a_1p8: ldo7 { 216 regulator-min-microvolt = <1800000>; 217 regulator-max-microvolt = <1800000>; 218 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 219 }; 220 221 vreg_l8a_1p2: ldo8 { 222 regulator-min-microvolt = <1200000>; 223 regulator-max-microvolt = <1248000>; 224 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 225 }; 226 227 vreg_l9a_1p8: ldo9 { 228 regulator-min-microvolt = <1704000>; 229 regulator-max-microvolt = <2928000>; 230 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 231 }; 232 233 vreg_l10a_1p8: ldo10 { 234 regulator-min-microvolt = <1704000>; 235 regulator-max-microvolt = <2928000>; 236 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 237 }; 238 239 vreg_l11a_1p0: ldo11 { 240 regulator-min-microvolt = <1000000>; 241 regulator-max-microvolt = <1048000>; 242 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 243 }; 244 245 vdd_qfprom: 246 vdd_qfprom_sp: 247 vdda_apc1_cs_1p8: 248 vdda_gfx_cs_1p8: 249 vdda_qrefs_1p8: 250 vdda_qusb_hs0_1p8: 251 vddpx_11: 252 vreg_l12a_1p8: ldo12 { 253 regulator-min-microvolt = <1800000>; 254 regulator-max-microvolt = <1800000>; 255 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 256 }; 257 258 vddpx_2: 259 vreg_l13a_2p95: ldo13 { 260 regulator-min-microvolt = <1800000>; 261 regulator-max-microvolt = <2960000>; 262 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 263 }; 264 265 vreg_l14a_1p88: ldo14 { 266 regulator-min-microvolt = <1800000>; 267 regulator-max-microvolt = <1800000>; 268 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 269 }; 270 271 vreg_l15a_1p8: ldo15 { 272 regulator-min-microvolt = <1800000>; 273 regulator-max-microvolt = <1800000>; 274 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 275 }; 276 277 vreg_l16a_2p7: ldo16 { 278 regulator-min-microvolt = <2704000>; 279 regulator-max-microvolt = <2704000>; 280 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 281 }; 282 283 vreg_l17a_1p3: ldo17 { 284 regulator-min-microvolt = <1304000>; 285 regulator-max-microvolt = <1304000>; 286 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 287 }; 288 289 vreg_l18a_2p7: ldo18 { 290 regulator-min-microvolt = <2704000>; 291 regulator-max-microvolt = <2960000>; 292 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 293 }; 294 295 vreg_l19a_3p0: ldo19 { 296 regulator-min-microvolt = <2856000>; 297 regulator-max-microvolt = <3104000>; 298 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 299 }; 300 301 vreg_l20a_2p95: ldo20 { 302 regulator-min-microvolt = <2704000>; 303 regulator-max-microvolt = <2960000>; 304 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 305 }; 306 307 vreg_l21a_2p95: ldo21 { 308 regulator-min-microvolt = <2704000>; 309 regulator-max-microvolt = <2960000>; 310 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 311 }; 312 313 vreg_l22a_2p85: ldo22 { 314 regulator-min-microvolt = <2864000>; 315 regulator-max-microvolt = <3312000>; 316 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 317 }; 318 319 vreg_l23a_3p3: ldo23 { 320 regulator-min-microvolt = <3000000>; 321 regulator-max-microvolt = <3312000>; 322 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 323 }; 324 325 vdda_qusb_hs0_3p1: 326 vreg_l24a_3p075: ldo24 { 327 regulator-min-microvolt = <3088000>; 328 regulator-max-microvolt = <3088000>; 329 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 330 }; 331 332 vreg_l25a_3p3: ldo25 { 333 regulator-min-microvolt = <3300000>; 334 regulator-max-microvolt = <3312000>; 335 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 336 }; 337 338 vdda_hp_pcie_1p2: 339 vdda_hv_ebi0: 340 vdda_hv_ebi1: 341 vdda_hv_ebi2: 342 vdda_hv_ebi3: 343 vdda_mipi_csi_1p25: 344 vdda_mipi_dsi0_1p2: 345 vdda_mipi_dsi1_1p2: 346 vdda_pcie_1p2: 347 vdda_ufs1_1p2: 348 vdda_ufs2_1p2: 349 vdda_usb1_ss_1p2: 350 vdda_usb2_ss_1p2: 351 vreg_l26a_1p2: ldo26 { 352 regulator-min-microvolt = <1200000>; 353 regulator-max-microvolt = <1200000>; 354 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 355 }; 356 357 vreg_l28a_3p0: ldo28 { 358 regulator-min-microvolt = <2856000>; 359 regulator-max-microvolt = <3008000>; 360 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 361 }; 362 363 vreg_lvs1a_1p8: lvs1 { 364 regulator-min-microvolt = <1800000>; 365 regulator-max-microvolt = <1800000>; 366 }; 367 368 vreg_lvs2a_1p8: lvs2 { 369 regulator-min-microvolt = <1800000>; 370 regulator-max-microvolt = <1800000>; 371 }; 372 }; 373 374 regulators-1 { 375 compatible = "qcom,pmi8998-rpmh-regulators"; 376 qcom,pmic-id = "b"; 377 378 vdd-bob-supply = <&vph_pwr>; 379 380 vreg_bob: bob { 381 regulator-min-microvolt = <3312000>; 382 regulator-max-microvolt = <3600000>; 383 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; 384 regulator-allow-bypass; 385 }; 386 }; 387 388 regulators-2 { 389 compatible = "qcom,pm8005-rpmh-regulators"; 390 qcom,pmic-id = "c"; 391 392 vdd-s1-supply = <&vph_pwr>; 393 vdd-s2-supply = <&vph_pwr>; 394 vdd-s3-supply = <&vph_pwr>; 395 vdd-s4-supply = <&vph_pwr>; 396 397 vreg_s3c_0p6: smps3 { 398 regulator-min-microvolt = <600000>; 399 regulator-max-microvolt = <600000>; 400 }; 401 }; 402}; 403 404&cdsp_pas { 405 status = "okay"; 406 firmware-name = "qcom/sdm845/cdsp.mbn"; 407}; 408 409&gcc { 410 protected-clocks = <GCC_QSPI_CORE_CLK>, 411 <GCC_QSPI_CORE_CLK_SRC>, 412 <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, 413 <GCC_LPASS_Q6_AXI_CLK>, 414 <GCC_LPASS_SWAY_CLK>; 415}; 416 417&gpu { 418 status = "okay"; 419 420 zap-shader { 421 memory-region = <&gpu_mem>; 422 firmware-name = "qcom/sdm845/a630_zap.mbn"; 423 }; 424}; 425 426&i2c10 { 427 status = "okay"; 428 clock-frequency = <400000>; 429}; 430 431&ipa { 432 qcom,gsi-loader = "self"; 433 memory-region = <&ipa_fw_mem>; 434 status = "okay"; 435}; 436 437&mdss { 438 status = "okay"; 439}; 440 441&mdss_dsi0 { 442 status = "okay"; 443 vdda-supply = <&vdda_mipi_dsi0_1p2>; 444 445 qcom,dual-dsi-mode; 446 qcom,master-dsi; 447 448 ports { 449 port@1 { 450 endpoint { 451 remote-endpoint = <&truly_in_0>; 452 data-lanes = <0 1 2 3>; 453 }; 454 }; 455 }; 456 457 panel@0 { 458 compatible = "truly,nt35597-2K-display"; 459 reg = <0>; 460 vdda-supply = <&vreg_l14a_1p88>; 461 462 reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; 463 mode-gpios = <&tlmm 52 GPIO_ACTIVE_HIGH>; 464 465 ports { 466 #address-cells = <1>; 467 #size-cells = <0>; 468 469 port@0 { 470 reg = <0>; 471 truly_in_0: endpoint { 472 remote-endpoint = <&mdss_dsi0_out>; 473 }; 474 }; 475 476 port@1 { 477 reg = <1>; 478 truly_in_1: endpoint { 479 remote-endpoint = <&mdss_dsi1_out>; 480 }; 481 }; 482 }; 483 }; 484}; 485 486&mdss_dsi0_phy { 487 status = "okay"; 488 vdds-supply = <&vdda_mipi_dsi0_pll>; 489}; 490 491&mdss_dsi1 { 492 status = "okay"; 493 vdda-supply = <&vdda_mipi_dsi1_1p2>; 494 495 qcom,dual-dsi-mode; 496 497 /* DSI1 is slave, so use DSI0 clocks */ 498 assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>; 499 500 ports { 501 port@1 { 502 endpoint { 503 remote-endpoint = <&truly_in_1>; 504 data-lanes = <0 1 2 3>; 505 }; 506 }; 507 }; 508}; 509 510&mdss_dsi1_phy { 511 status = "okay"; 512 vdds-supply = <&vdda_mipi_dsi1_pll>; 513}; 514 515&mss_pil { 516 status = "okay"; 517 firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mbn"; 518}; 519 520&pcie0 { 521 perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>; 522 523 pinctrl-0 = <&pcie0_default_state>; 524 pinctrl-names = "default"; 525 526 status = "okay"; 527}; 528 529&pcie0_phy { 530 vdda-phy-supply = <&vreg_l1a_0p875>; 531 vdda-pll-supply = <&vreg_l26a_1p2>; 532 533 status = "okay"; 534}; 535 536&pcie1 { 537 perst-gpios = <&tlmm 102 GPIO_ACTIVE_LOW>; 538 539 pinctrl-names = "default"; 540 pinctrl-0 = <&pcie1_default_state>; 541 542 status = "okay"; 543}; 544 545&pcie1_phy { 546 status = "okay"; 547 548 vdda-phy-supply = <&vreg_l1a_0p875>; 549 vdda-pll-supply = <&vreg_l26a_1p2>; 550}; 551 552&pm8998_adc { 553 channel@4c { 554 reg = <ADC5_XO_THERM_100K_PU>; 555 label = "xo_therm"; 556 qcom,ratiometric; 557 qcom,hw-settle-time = <200>; 558 }; 559 560 channel@4d { 561 reg = <ADC5_AMUX_THM1_100K_PU>; 562 label = "msm_therm"; 563 qcom,ratiometric; 564 qcom,hw-settle-time = <200>; 565 }; 566 567 channel@4f { 568 reg = <ADC5_AMUX_THM3_100K_PU>; 569 label = "pa_therm1"; 570 qcom,ratiometric; 571 qcom,hw-settle-time = <200>; 572 }; 573 574 channel@51 { 575 reg = <ADC5_AMUX_THM5_100K_PU>; 576 label = "quiet_therm"; 577 qcom,ratiometric; 578 qcom,hw-settle-time = <200>; 579 }; 580 581 channel@83 { 582 reg = <ADC5_VPH_PWR>; 583 label = "vph_pwr"; 584 qcom,ratiometric; 585 qcom,hw-settle-time = <200>; 586 }; 587 588 channel@85 { 589 reg = <ADC5_VCOIN>; 590 label = "vcoin"; 591 qcom,ratiometric; 592 qcom,hw-settle-time = <200>; 593 }; 594}; 595 596&pm8998_adc_tm { 597 status = "okay"; 598 599 xo-thermistor@1 { 600 reg = <1>; 601 io-channels = <&pm8998_adc ADC5_XO_THERM_100K_PU>; 602 qcom,ratiometric; 603 qcom,hw-settle-time-us = <200>; 604 }; 605 606 msm-thermistor@2 { 607 reg = <2>; 608 io-channels = <&pm8998_adc ADC5_AMUX_THM1_100K_PU>; 609 qcom,ratiometric; 610 qcom,hw-settle-time-us = <200>; 611 }; 612 613 pa-thermistor@3 { 614 reg = <3>; 615 io-channels = <&pm8998_adc ADC5_AMUX_THM3_100K_PU>; 616 qcom,ratiometric; 617 qcom,hw-settle-time-us = <200>; 618 }; 619 620 quiet-thermistor@4 { 621 reg = <4>; 622 io-channels = <&pm8998_adc ADC5_AMUX_THM5_100K_PU>; 623 qcom,ratiometric; 624 qcom,hw-settle-time-us = <200>; 625 }; 626}; 627 628&pm8998_resin { 629 linux,code = <KEY_VOLUMEDOWN>; 630 status = "okay"; 631}; 632 633&qupv3_id_1 { 634 status = "okay"; 635}; 636 637&sdhc_2 { 638 status = "okay"; 639 640 pinctrl-names = "default"; 641 pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data &sd_card_det_n>; 642 643 vmmc-supply = <&vreg_l21a_2p95>; 644 vqmmc-supply = <&vddpx_2>; 645 646 cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>; 647}; 648 649&tlmm { 650 pcie0_default_state: pcie0-default-state { 651 clkreq-pins { 652 pins = "gpio36"; 653 function = "pci_e0"; 654 bias-pull-up; 655 }; 656 657 perst-n-pins { 658 pins = "gpio35"; 659 function = "gpio"; 660 drive-strength = <2>; 661 bias-pull-down; 662 }; 663 664 wake-n-pins { 665 pins = "gpio37"; 666 function = "gpio"; 667 drive-strength = <2>; 668 bias-pull-up; 669 }; 670 }; 671 672 pcie1_default_state: pcie1-default-state { 673 clkreq-pins { 674 pins = "gpio103"; 675 function = "pci_e1"; 676 bias-pull-up; 677 }; 678 679 perst-n-pins { 680 pins = "gpio102"; 681 function = "gpio"; 682 drive-strength = <16>; 683 bias-pull-down; 684 }; 685 686 wake-n-pins { 687 pins = "gpio104"; 688 function = "gpio"; 689 drive-strength = <2>; 690 bias-pull-up; 691 }; 692 }; 693}; 694 695&uart9 { 696 status = "okay"; 697}; 698 699&ufs_mem_hc { 700 status = "okay"; 701 702 reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>; 703 704 vcc-supply = <&vreg_l20a_2p95>; 705 vcc-max-microamp = <600000>; 706}; 707 708&ufs_mem_phy { 709 status = "okay"; 710 711 vdda-phy-supply = <&vdda_ufs1_core>; 712 vdda-pll-supply = <&vdda_ufs1_1p2>; 713}; 714 715&usb_1 { 716 status = "okay"; 717}; 718 719&usb_1_dwc3 { 720 /* Until we have Type C hooked up we'll force this as peripheral. */ 721 dr_mode = "peripheral"; 722}; 723 724&usb_1_hsphy { 725 status = "okay"; 726 727 vdd-supply = <&vdda_usb1_ss_core>; 728 vdda-pll-supply = <&vdda_qusb_hs0_1p8>; 729 vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; 730 731 qcom,imp-res-offset-value = <8>; 732 qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; 733 qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; 734 qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; 735}; 736 737&usb_1_qmpphy { 738 status = "okay"; 739 740 vdda-phy-supply = <&vdda_usb1_ss_1p2>; 741 vdda-pll-supply = <&vdda_usb1_ss_core>; 742}; 743 744&usb_2 { 745 status = "okay"; 746}; 747 748&usb_2_dwc3 { 749 /* 750 * Though the USB block on SDM845 can support host, there's no vbus 751 * signal for this port on MTP. Thus (unless you have a non-compliant 752 * hub that works without vbus) the only sensible thing is to force 753 * peripheral mode. 754 */ 755 dr_mode = "peripheral"; 756}; 757 758&usb_2_hsphy { 759 status = "okay"; 760 761 vdd-supply = <&vdda_usb2_ss_core>; 762 vdda-pll-supply = <&vdda_qusb_hs0_1p8>; 763 vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; 764 765 qcom,imp-res-offset-value = <8>; 766 qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>; 767}; 768 769&usb_2_qmpphy { 770 status = "okay"; 771 772 vdda-phy-supply = <&vdda_usb2_ss_1p2>; 773 vdda-pll-supply = <&vdda_usb2_ss_core>; 774}; 775 776&venus { 777 status = "okay"; 778}; 779 780&wifi { 781 status = "okay"; 782 vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; 783 vdd-1.8-xo-supply = <&vreg_l7a_1p8>; 784 vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; 785 vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; 786 787 qcom,snoc-host-cap-8bit-quirk; 788 qcom,calibration-variant = "Qualcomm_sdm845mtp"; 789}; 790 791/* PINCTRL - additions to nodes defined in sdm845.dtsi */ 792 793&qup_i2c10_default { 794 drive-strength = <2>; 795 bias-disable; 796}; 797 798&qup_uart9_rx { 799 drive-strength = <2>; 800 bias-pull-up; 801}; 802 803&qup_uart9_tx { 804 drive-strength = <2>; 805 bias-disable; 806}; 807 808&tlmm { 809 gpio-reserved-ranges = <0 4>, <81 4>; 810 811 sdc2_clk: sdc2-clk-state { 812 pins = "sdc2_clk"; 813 bias-disable; 814 815 /* 816 * It seems that mmc_test reports errors if drive 817 * strength is not 16 on clk, cmd, and data pins. 818 */ 819 drive-strength = <16>; 820 }; 821 822 sdc2_cmd: sdc2-cmd-state { 823 pins = "sdc2_cmd"; 824 bias-pull-up; 825 drive-strength = <16>; 826 }; 827 828 sdc2_data: sdc2-data-state { 829 pins = "sdc2_data"; 830 bias-pull-up; 831 drive-strength = <16>; 832 }; 833 834 sd_card_det_n: sd-card-det-n-state { 835 pins = "gpio126"; 836 function = "gpio"; 837 bias-pull-up; 838 }; 839}; 840