| /src/sys/contrib/device-tree/Bindings/display/bridge/ |
| H A D | renesas,dw-hdmi.txt | 33 - ports: See dw_hdmi.txt. The DWC HDMI shall have one port numbered 0
34 corresponding to the video input of the controller and one port numbered 1
35 corresponding to its HDMI output, and one port numbered 2 corresponding to
|
| /src/usr.bin/patch/ |
| H A D | backupfile.c | 225 numbered_existing, numbered, numbered enumerator
|
| H A D | backupfile.h | 31 numbered enumerator
|
| /src/sys/contrib/device-tree/Bindings/media/ |
| H A D | cdns,csi2tx.txt | 26 port nodes are numbered as follows.
39 the endpoints are not numbered.
|
| H A D | cdns,csi2rx.txt | 26 port nodes are numbered as follows:
39 the endpoints are not numbered.
|
| H A D | st,stih4xx.txt | 25 Each BDISP should have a numbered alias in the aliases node, in the form of
|
| H A D | exynos5-gsc.txt | 27 Each G-Scaler node should have a numbered alias in the aliases node,
|
| /src/sys/contrib/device-tree/Bindings/pinctrl/ |
| H A D | pinctrl-mt65xx.txt | 17 - pins-are-numbered: Specify the subnodes are using numbered pinmux to
96 pins-are-numbered;
|
| /src/sys/contrib/openzfs/etc/zfs/ |
| H A D | vdev_id.conf.scsi.example | 4 # Usually scsi disks are numbered from 0, but this can be offset, to
|
| /src/sys/contrib/device-tree/Bindings/display/rockchip/ |
| H A D | dw_hdmi-rockchip.txt | 24 - ports: See dw_hdmi.txt. The DWC HDMI shall have a single port numbered 0
26 endpoints, numbered 0 and 1, connected respectively to the vopb and vopl.
|
| /src/sys/contrib/device-tree/Bindings/net/ |
| H A D | mdio-gpio.txt | 12 Note: Each gpio-mdio bus should have an alias correctly numbered in "aliases"
|
| /src/sys/contrib/device-tree/Bindings/serial/ |
| H A D | arc-uart.txt | 20 Note: Each port should have an alias correctly numbered in "aliases" node.
|
| H A D | digicolor-usart.txt | 14 Note: Each UART port should have an alias correctly numbered
|
| H A D | cirrus,clps711x-uart.txt | 14 Note: Each UART port should have an alias correctly numbered
|
| H A D | fsl-imx-uart.txt | 25 Note: Each uart controller should have an alias correctly numbered
|
| /src/sys/contrib/device-tree/Bindings/timer/ |
| H A D | cirrus,clps711x-timer.txt | 9 Note: Each timer should have an alias correctly numbered in "aliases" node.
|
| /src/tools/tools/man/ |
| H A D | README | 21 adding the numbered args is a bit redundant.
|
| /src/sys/contrib/device-tree/Bindings/gpio/ |
| H A D | gpio-clps711x.txt | 14 Note: Each GPIO port should have an alias correctly numbered in "aliases"
|
| /src/sys/contrib/device-tree/Bindings/sound/ |
| H A D | mxs-saif.txt | 16 Note: Each SAIF controller should have an alias correctly numbered
|
| /src/sys/contrib/device-tree/Bindings/mips/cavium/ |
| H A D | cib.txt | 13 - cavium,max-bits: The index (zero based) of the highest numbered bit
|
| /src/sys/contrib/device-tree/Bindings/media/i2c/ |
| H A D | adv7180.txt | 24 nodes are numbered as follows.
|
| /src/sys/contrib/device-tree/Bindings/usb/ |
| H A D | am33xx-usb.txt | 26 The PHY should have a "phy" alias numbered properly in the alias
51 The controller should have an "usb" alias numbered properly in the alias
|
| /src/sys/contrib/device-tree/Bindings/media/xilinx/ |
| H A D | xlnx,v-tpg.txt | 22 The TPG has a single output port numbered 0.
|
| /src/sys/contrib/device-tree/Bindings/display/imx/ |
| H A D | hdmi.txt | 20 numbered 0 to 3, corresponding to the four inputs of the HDMI multiplexer.
|
| /src/sys/contrib/openzfs/config/ |
| H A D | user-libunwind.m4 | 39 dnl defines the highest numbered register in a different
|