| /src/sys/contrib/device-tree/Bindings/power/supply/ |
| H A D | ingenic,battery.txt | 1 * Ingenic JZ47xx battery bindings
5 - compatible: Must be "ingenic,jz4740-battery".
8 - monitored-battery: phandle to a "simple-battery" compatible node.
10 The "monitored-battery" property must be a phandle to a node using the format
11 described in battery.txt, with the following properties being required:
13 - voltage-min-design-microvolt: Drained battery voltage.
14 - voltage-max-design-microvolt: Fully charged battery voltage.
20 simple_battery: battery {
21 compatible = "simple-battery";
27 compatible = "ingenic,jz4740-battery";
[all …]
|
| H A D | charger-manager.txt | 8 - cm-fuel-gauge : name of battery fuel gauge
20 - cm-name : charger manager's name (default : "battery")
25 - cm-battery-stat : battery status - 0 for battery always present, 1 for no
26 battery, 2 to check presence via fuel gauge, or 3 to check presence
29 - cm-fullbatt-voltage : voltage (in uV) of full battery
30 - cm-fullbatt-soc : state of charge to consider as full battery
31 - cm-fullbatt-capacity : capcity (in uAh) to consider as full battery
33 - cm-battery-* : threshold battery temperature for charging
34 -cold : critical cold temperature of battery for charging
36 -hot : critical hot temperature of battery for charging
[all …]
|
| H A D | stericsson,ab8500-battery.txt | 2 information about the battery connected to the PMIC.
8 A boolean value indicating thermistor interface to battery
11 'btemp' and 'batctrl' are the pins interfaced for battery temperature
13 coefficient) resister is interfaced external to battery whereas
14 'batctrl' pin is used when NTC resister is internal to battery.
20 indicates: NTC resister is internal to battery, 'batctrl' is used
24 NTC resister is external to battery and 'btemp' signal is used
27 battery-type:
28 This shall be the battery manufacturing technology type,
33 stericsson,battery-type = "LIPO";
|
| H A D | axp20x_battery.txt | 1 AXP20x and AXP22x battery power supply
5 "x-powers,axp209-battery-power-supply"
6 "x-powers,axp221-battery-power-supply"
7 "x-powers,axp813-battery-power-supply"
11 The supported devices can read the battery voltage, charge and discharge
12 currents of the battery by reading ADC channels from the ADC.
17 battery_power_supply: battery-power-supply {
18 compatible = "x-powers,axp209-battery-power-supply";
|
| H A D | rx51-battery.txt | 1 Binding for Nokia N900 battery
3 The Nokia N900 battery status can be read via the TWL4030's A/D converter.
7 * "nokia,n900-battery"
12 * "bsi" - The ADC channel for battery size identification
13 * "vbat" - The ADC channel to measure the battery voltage
17 battery: n900-battery {
18 compatible = "nokia,n900-battery";
|
| H A D | bq24190.txt | 13 - monitored-battery: phandle of battery characteristics devicetree node
14 The charger uses the following battery properties:
16 phase (typically 20% of battery capacity).
18 battery voltage is above recharge threshold, and the current is below
19 this setting (typically 10% of battery capacity).
20 See also Documentation/devicetree/bindings/power/supply/battery.txt
21 - ti,system-minimum-microvolt: when power is connected and the battery is below
37 bat: battery {
38 compatible = "simple-battery";
48 monitored-battery = <&bat>;
|
| H A D | sc2731_charger.txt | 1 Spreadtrum SC2731 PMIC battery charger binding
9 - monitored-battery: phandle of battery characteristics devicetree node.
10 The charger uses the following battery properties:
13 See Documentation/devicetree/bindings/power/supply/battery.txt
17 bat: battery {
18 compatible = "simple-battery";
38 monitored-battery = <&bat>;
|
| H A D | sbs,sbs-manager.txt | 16 four smart battery devices at address 0xb. The driver actually implements this
36 battery@b {
37 compatible = "ti,bq2060", "sbs,sbs-battery";
39 sbs,battery-detect-gpios = <&batman 1 1>;
48 battery@b {
49 compatible = "ti,bq2060", "sbs,sbs-battery";
51 sbs,battery-detect-gpios = <&batman 2 1>;
60 battery@b {
61 compatible = "ti,bq2060", "sbs,sbs-battery";
63 sbs,battery-detect-gpios = <&batman 3 1>;
|
| H A D | lego_ev3_battery.txt | 4 LEGO MINDSTORMS EV3 has some built-in capability for monitoring the battery.
5 It uses 6 AA batteries or a special Li-ion rechargeable battery pack that is
6 detected by a key switch in the battery compartment.
9 - compatible: Must be "lego,ev3-battery"
12 - rechargeable-gpios: phandle to the rechargeable battery indication gpio
16 battery {
17 compatible = "lego,ev3-battery";
|
| H A D | sc27xx-fg.txt | 11 - battery-detect-gpios: GPIO for battery detection.
18 - monitored-battery: Phandle of battery characteristics devicetree node.
19 See Documentation/devicetree/bindings/power/supply/battery.txt
23 bat: battery {
24 compatible = "simple-battery";
51 battery-detect-gpios = <&pmic_eic 9 GPIO_ACTIVE_HIGH>;
56 monitored-battery = <&bat>;
|
| H A D | bq2415x.txt | 20 - ti,weak-battery-voltage: integer, weak battery voltage threshold in mV.
21 The chip will use slow precharge if battery voltage
23 - ti,battery-regulation-voltage: integer, maximum charging voltage in mV.
40 ti,weak-battery-voltage = <3400>;
41 ti,battery-regulation-voltage = <4200>;
|
| H A D | max17042_battery.txt | 18 - maxim,cold-temp : Temperature threshold to report battery
20 - maxim,over-heat-temp : Temperature threshold to report battery
22 - maxim,dead-volt : Voltage threshold to report battery
24 - maxim,over-volt : Voltage threshold to report battery
29 battery-charger@36 {
|
| H A D | max17040_battery.txt | 7 "maxim,max17058", "maxim,max17059" or "maxim,max77836-battery"
21 battery chemistries and operating temperatures.
33 compatible "maxim,max77836-battery".
37 battery-fuel-gauge@36 {
38 compatible = "maxim,max77836-battery";
46 battery-fuel-gauge@36 {
|
| H A D | olpc_battery.txt | 1 OLPC battery
5 - compatible : "olpc,xo1-battery" or "olpc,xo1.5-battery"
|
| /src/sys/contrib/device-tree/Bindings/power/supply/ab8500/ |
| H A D | fg.txt | 10 main-charger, usb-combo-charger and battery-temperature-monitoring.
16 - battery = Shall be battery specific information
20 battery = <&ab8500_battery>;
27 'battery technology type' used.
31 A boolean value indicating thermistor interface to battery
34 'btemp' and 'batctrl' are the pins interfaced for battery temperature
36 coefficient) resister is interfaced external to battery whereas
37 'batctrl' pin is used when NTC resister is internal to battery.
43 indicates: NTC resister is internal to battery, 'batctrl' is used
47 NTC resister is external to battery and 'btemp' signal is used
[all …]
|
| H A D | btemp.txt | 7 - battery = Shall be battery specific information
12 battery = <&ab8500_battery>;
15 For information on battery specific node, Ref:
|
| H A D | chargalg.txt | 7 - battery = Shall be battery specific information
12 battery = <&ab8500_battery>;
15 For information on battery specific node, Ref:
|
| H A D | charger.txt | 5 - battery = Shall be battery specific information
9 battery = <&ab8500_battery>;
24 For information on battery specific node, Ref:
|
| /src/sys/contrib/device-tree/Bindings/rtc/ |
| H A D | rtc-palmas.txt | 10 - ti,backup-battery-chargeable: The Palmas series device like TPS65913 or
11 TPS80036 supports the backup battery for powering the RTC when main
12 battery is removed or in very low power state. The backup battery
14 battery is chargeable or not. If charging battery then driver can
16 - ti,backup-battery-charge-high-current: Enable high current charging in
17 backup battery. Device supports the < 100uA and > 100uA charging.
19 charge battery to lower current i.e. < 100uA.
28 ti,backup-battery-chargeable;
29 ti,backup-battery-charge-high-current;
|
| /src/sys/contrib/device-tree/src/arm64/qcom/ |
| H A D | sdm845-oneplus-fajita.dts | 17 battery: battery { label
18 compatible = "simple-battery";
37 monitored-battery = <&battery>;
51 monitored-battery = <&battery>;
|
| H A D | sdm845-oneplus-enchilada.dts | 17 battery: battery { label
18 compatible = "simple-battery";
33 monitored-battery = <&battery>;
55 monitored-battery = <&battery>;
|
| H A D | msm8916-lg-m216.dts | 25 battery: battery { label
26 compatible = "simple-battery";
126 monitored-battery = <&battery>;
136 monitored-battery = <&battery>;
|
| /src/sys/contrib/device-tree/src/arm64/rockchip/ |
| H A D | rk3326-odroid-go2.dts | 40 battery: battery { label
41 compatible = "simple-battery";
67 monitored-battery = <&battery>;
|
| H A D | rk3566-anbernic-rg353vs.dts | 20 battery: battery { label
21 compatible = "simple-battery";
82 monitored-battery = <&battery>;
|
| /src/sys/contrib/device-tree/src/arm/st/ |
| H A D | ste-ab8505.dtsi | 13 <&gpadc 0x08>, /* Main battery voltage */
16 <&gpadc 0x0c>, /* Backup battery voltage */
115 monitored-battery = <&battery>;
132 monitored-battery = <&battery>;
169 monitored-battery = <&battery>;
179 monitored-battery = <&battery>;
|