Searched refs:pullups (Results 1 – 20 of 20) sorted by relevance
| /linux/include/linux/platform_data/ |
| H A D | st_sensors_pdata.h | 21 * @pullups: enable/disable i2c controller pullup resistors.
28 bool pullups; member
|
| /linux/arch/arm/boot/dts/ti/omap/ |
| H A D | omap3-cm-t3x30.dtsi | 94 /* pullups: BIT(0) */
95 ti,pullups = <0x000001>;
|
| H A D | omap4-sdp-es23plus.dts | 7 /* SDP boards with 4430 ES2.3+ or 4460 have external pullups on SCL & SDA */
|
| H A D | omap4-panda-a4.dts | 15 /* Pandaboard Rev A4+ have external pullups on SCL & SDA */
|
| H A D | omap4-panda-es.dts | 31 /* PandaboardES has external pullups on SCL & SDA */
|
| H A D | omap3-beagle-xm.dts | 327 /* pullups: BIT(1) */
328 ti,pullups = <0x000002>;
|
| H A D | omap3-tao3530.dtsi | 243 /* pullups: BIT(1) */
244 ti,pullups = <0x000002>;
|
| H A D | omap3-beagle.dts | 309 /* pullups: BIT(1) */
310 ti,pullups = <0x000002>;
|
| H A D | omap3-gta04.dtsi | 682 /* pullups: BIT(2) */
683 ti,pullups = <BIT(2)>;
|
| H A D | omap3-n950-n9.dtsi | 165 ti,pullups = <0x000001>; /* BIT(0) */
|
| H A D | omap3-n900.dts | 572 ti,pullups = <0x0>;
|
| /linux/drivers/gpio/ |
| H A D | gpio-twl4030.c | 31 * inputs or outputs, with pullups or pulldowns on each pin. Each
486 of_property_read_u32(dev->of_node, "ti,pullups", in of_gpio_twl4030()
487 &omap_twl_info->pullups); in of_gpio_twl4030()
551 * NOTE: boards may waste power if they don't set pullups in gpio_twl4030_probe()
553 * pulldown, and some other pins may have external pullups in gpio_twl4030_probe()
556 ret = gpio_twl4030_pulls(pdata->pullups, pdata->pulldowns); in gpio_twl4030_probe()
558 dev_dbg(&pdev->dev, "pullups %.05x %.05x --> %d\n", in gpio_twl4030_probe()
559 pdata->pullups, pdata->pulldowns, ret); in gpio_twl4030_probe()
|
| /linux/Documentation/devicetree/bindings/pinctrl/ |
| H A D | pinctrl-sirf.txt | 10 - sirf,pullups : if n-th bit of m-th bank is set, set a pullup on GPIO-n of bank m
|
| /linux/Documentation/spi/ |
| H A D | butterfly.rst | 43 (a) flash new firmware that disables SPI (set PRR.2, and disable pullups
|
| /linux/arch/arm/boot/dts/samsung/ |
| H A D | exynos5250-spring.dts | 360 * Disabled pullups since external part has its own pullups and
|
| H A D | exynos5250-snow-common.dtsi | 451 * Disabled pullups since external part has its own pullups and
|
| /linux/include/linux/mfd/ |
| H A D | twl.h | 569 /* For gpio-N, bit (1 << N) in "pullups" is set if that pullup
574 u32 pullups; member
|
| /linux/arch/arm64/boot/dts/rockchip/ |
| H A D | rk3399-gru-chromebook.dtsi | 464 * still allows us to get nice 4.7K pullups for high speed i2c
|
| /linux/Documentation/input/devices/ |
| H A D | joystick-parport.rst | 261 gamepads the pullups are not needed.
|
| /linux/drivers/iio/imu/st_lsm6dsx/ |
| H A D | st_lsm6dsx_core.c | 2167 if (device_property_read_bool(dev, "st,pullups") || in st_lsm6dsx_init_shub()
2168 (pdata && pdata->pullups)) { in st_lsm6dsx_init_shub()
|