| /linux/drivers/input/touchscreen/ |
| H A D | ti_am335x_tsc.c | 51 unsigned int wires; member
135 switch (ts_dev->wires) { in titsc_step_config()
163 switch (ts_dev->wires) { in titsc_step_config()
356 err = of_property_read_u32(node, "ti,wires", &ts_dev->wires); in titsc_parse_dt()
359 switch (ts_dev->wires) { in titsc_parse_dt()
|
| H A D | fsl-imx25-tcq.c | 435 u32 wires; in mx25_tcq_parse_dt() local
444 error = of_property_read_u32(np, "fsl,wires", &wires); in mx25_tcq_parse_dt()
450 if (wires == 4) { in mx25_tcq_parse_dt()
453 dev_err(&pdev->dev, "%u-wire mode not supported\n", wires); in mx25_tcq_parse_dt()
|
| /linux/Documentation/devicetree/bindings/input/touchscreen/ |
| H A D | fsl-mx25-tcq.txt | 11 - fsl,wires: Should be '<4>' or '<5>'
33 fsl,wires = <4>;
|
| /linux/arch/arm/mach-omap1/ |
| H A D | devices.c | 81 if (mmc_controller->slots[0].wires == 4) { in omap1_mmc_mux()
97 if (mmc_controller->slots[1].wires == 4) { in omap1_mmc_mux()
|
| /linux/include/linux/platform_data/ |
| H A D | mmc-davinci.h | 20 u8 wires; member
|
| H A D | mmc-omap.h | 44 u8 wires; /* Used for the MMC driver on omap1 and 2420 */ member
|
| /linux/Documentation/devicetree/bindings/display/tilcdc/ |
| H A D | tilcdc.txt | 25 - "crossed" indicates wiring that has blue and red wires
44 the wires work as they should (LCD_DATA[0:4] is for Blue[3:7]),
|
| /linux/arch/arm/boot/dts/microchip/ |
| H A D | sama5d3xdm.dtsi | 25 atmel,adc-ts-wires = <4>;
|
| H A D | at91-cosino_mega2560.dts | 23 atmel,adc-ts-wires = <4>;
|
| H A D | at91sam9x5dm.dtsi | 58 atmel,adc-ts-wires = <4>;
|
| H A D | at91-cosino.dtsi | 39 atmel,adc-ts-wires = <4>;
|
| H A D | at91-sama5d4_ma5d4evk.dts | 87 atmel,adc-ts-wires = <4>;
|
| H A D | at91sam9x5ek.dtsi | 36 atmel,adc-ts-wires = <4>;
|
| H A D | at91sam9rlek.dts | 171 atmel,adc-ts-wires = <4>;
|
| /linux/drivers/gpu/drm/amd/acp/ |
| H A D | Kconfig | 12 This adds the ACP (Audio CoProcessor) IP driver and wires
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-bus-iio-thermocouple | 17 such as those caused by broken thermocouple wires.
|
| /linux/Documentation/devicetree/bindings/sound/ |
| H A D | mt6358.txt | 17 channels of PDM signal. 0 means two wires, 1 means one wire. Default
|
| /linux/drivers/comedi/drivers/ |
| H A D | comedi_test.c | 701 u16 wires; in waveform_dio_insn_bits() local
717 wires = 0xFFFF & ~driven_low & ~(driven_low >> 16); in waveform_dio_insn_bits()
719 data[1] = wires | (wires << 16); in waveform_dio_insn_bits()
|
| /linux/Documentation/driver-api/gpio/ |
| H A D | drivers-on-gpio.rst | 26 mouse cable and connect the wires to GPIO lines or solder a mouse connector
54 (two wires, SDA and SCL lines) by hammering (bitbang) two GPIO lines. It will
59 of wires, at least SCK and optionally MISO, MOSI and chip select lines) using
|
| /linux/arch/arm/boot/dts/nxp/imx/ |
| H A D | imx6ul-ccimx6ulsbcpro.dts | 384 pinctrl_uart2_4wires: uart2-4wires-grp {
393 pinctrl_uart3_2wires: uart3-2wires-grp {
|
| /linux/arch/arm/boot/dts/nxp/mxs/ |
| H A D | imx28-cfa10058.dts | 68 fsl,lradc-touchscreen-wires = <4>;
|
| H A D | imx23-evk.dts | 105 fsl,lradc-touchscreen-wires = <4>;
|
| H A D | imx28-cfa10057.dts | 68 fsl,lradc-touchscreen-wires = <4>;
|
| H A D | imx28-cfa10055.dts | 82 fsl,lradc-touchscreen-wires = <4>;
|
| H A D | imx28-apf28dev.dts | 112 fsl,lradc-touchscreen-wires = <4>;
|