| /linux/Documentation/userspace-api/media/rc/ |
| H A D | lirc-get-send-mode.rst | 34 The mode used for transmitting. 65 - Device does not support transmitting.
|
| H A D | lirc-get-features.rst | 52 :ref:`LIRC_MODE_PULSE <lirc-mode-pulse>` can only be used for transmitting.
|
| /linux/drivers/media/cec/core/ |
| H A D | cec-adap.c | 361 if (adap->transmitting == data) { in cec_data_cancel() 362 adap->transmitting = NULL; in cec_data_cancel() 413 if (adap->transmitting) in cec_flush() 496 if (adap->transmitting) in cec_thread_func() 497 cec_data_cancel(adap->transmitting, in cec_thread_func() 513 if (adap->transmitting) { in cec_thread_func() 515 adap->transmitting->msg.len, in cec_thread_func() 516 adap->transmitting->msg.msg); in cec_thread_func() 518 cec_data_cancel(adap->transmitting, in cec_thread_func() 543 adap->transmitting = data; in cec_thread_func() [all …]
|
| /linux/drivers/net/team/ |
| H A D | Kconfig | 33 Basic mode where port used for transmitting packets is selected in 45 Basic mode where port used for transmitting packets is selected
|
| /linux/drivers/media/rc/ |
| H A D | redrat3.c | 224 bool transmitting; member 238 if (!rr3->transmitting && (code != 0x40)) in redrat3_dump_fw_error() 276 if (!rr3->transmitting) in redrat3_dump_fw_error() 760 if (rr3->transmitting) { in redrat3_transmit_ir() 769 rr3->transmitting = true; in redrat3_transmit_ir() 844 rr3->transmitting = false; in redrat3_transmit_ir()
|
| H A D | ite-cir.c | 181 bool for_tx = dev->transmitting; in ite_set_carrier_params() 348 dev->transmitting = true; in ite_tx_ir() 458 dev->transmitting = false; in ite_tx_ir() 1198 wait_event_interruptible(dev->tx_ended, !dev->transmitting); in ite_close() 1452 wait_event_interruptible(dev->tx_ended, !dev->transmitting); in ite_suspend()
|
| H A D | ite-cir.h | 84 bool transmitting; member
|
| /linux/Documentation/scsi/ |
| H A D | cxgb3i.rst | 18 On transmitting, Chelsio S3 h/w computes and inserts the Header and 32 On transmitting, S3 h/w accepts the complete PDU (header + data)
|
| /linux/drivers/usb/class/ |
| H A D | cdc-acm.h | 78 int transmitting; member
|
| /linux/Documentation/devicetree/bindings/media/ |
| H A D | st-rc.txt | 14 protocol used for transmitting remote control signals. tx-mode should
|
| /linux/Documentation/bpf/ |
| H A D | redirect.rst | 28 Not all drivers support transmitting frames after a redirect, and for
|
| /linux/Documentation/userspace-api/media/cec/ |
| H A D | cec-pin-error-inj.rst | 100 receiving CEC messages and those relating to transmitting CEC messages. In 165 keeps transmitting after the first byte was NACKed. 197 stop transmitting ('Arbitration Lost'). This is very hard to test, 215 This setting changes the behavior of transmitting CEC messages. Normally 308 Just stop transmitting after this bit. If <op> specifies a specific CEC
|
| H A D | cec-ioc-receive.rst | 148 transmitting the message. Ignored by :ref:`ioctl CEC_RECEIVE <CEC_RECEIVE>`. 176 transmitting the Poll message. 227 - Normally CEC messages are validated before transmitting them. If this
|
| /linux/Documentation/userspace-api/media/drivers/ |
| H A D | cx2341x-uapi.rst | 23 transmitting this block the first line of the block on the right to the 31 second line of 8 UV pairs of the top-left block, etc. After transmitting
|
| /linux/Documentation/networking/mac80211_hwsim/ |
| H A D | mac80211_hwsim.rst | 44 currently enabled and on the same channel as the transmitting
|
| /linux/Documentation/input/ |
| H A D | userio.rst | 61 Registers the port with the serio driver and begins transmitting data back and
|
| /linux/include/media/ |
| H A D | cec.h | 244 struct cec_data *transmitting; member
|
| /linux/Documentation/networking/caif/ |
| H A D | caif.rst | 132 might be problems transmitting over UART.
|
| H A D | linux_caif.rst | 85 - When receiving / transmitting CAIF Packets (cfpkt), ownership is passed
|
| /linux/drivers/staging/most/Documentation/ |
| H A D | driver_usage.txt | 205 When transmitting synchronous data the allocated channel width needs to be 223 When transmitting isochronous AVP data the desired packet size needs to be
|
| /linux/Documentation/userspace-api/media/v4l/ |
| H A D | dev-rds.rst | 13 at devices capable of receiving and/or transmitting RDS information.
|
| /linux/Documentation/driver-api/ |
| H A D | slimbus.rst | 36 Framer device is responsible for clocking the bus, and transmitting frame-sync
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-class-net-cdc_ncm | 76 aggregate before transmitting an NTB frame.
|
| /linux/Documentation/networking/ |
| H A D | tipc.rst | 23 transmitting data between cluster nodes? Where you yourself determine the
|
| /linux/Documentation/i2c/ |
| H A D | fault-codes.rst | 48 transmit mode: some other master was transmitting different
|