| /linux/Documentation/hwmon/ |
| H A D | da9055.rst | 36 Voltages are sampled in a AUTO mode it can be manually sampled too and results
50 Temperatures are sampled by a 10 bit ADC. Junction temperatures
|
| H A D | wm831x.rst | 28 Voltages are sampled by a 12 bit ADC. Voltages in millivolts are 1.465
34 Temperatures are sampled by a 12 bit ADC. Chip and battery temperatures
|
| H A D | da9052.rst | 46 Voltages are sampled by a 10 bit ADC.
63 Temperatures are sampled by a 10 bit ADC. Junction and battery temperatures
|
| H A D | wm8350.rst | 29 Voltages are sampled by a 12 bit ADC. For the internal supplies the ADC
|
| H A D | powr1220.rst | 26 Voltages are sampled by a 12-bit ADC with a step size of 2 mV.
|
| H A D | pwm-fan.rst | 20 from the sampled interrupts from the tachometer signal within 1 second.
|
| H A D | ltc4245.rst | 102 then they will be sampled in round-robin fashion. If userspace reads too
|
| H A D | bt1-pvt.rst | 62 The voltage inputs are also sampled with 10-bit resolution and reported in
|
| /linux/tools/testing/selftests/bpf/benchs/ |
| H A D | bench_ringbufs.c | 17 bool sampled; member
27 .sampled = false,
74 args.sampled = true; in parse_arg()
132 if (args.bench_producer && args.sampled) { in bufs_validate()
195 if (args.sampled) in ringbuf_setup_skeleton()
459 if (args.sampled) { in perfbuf_libbpf_setup()
|
| H A D | run_bench_ringbufs.sh | 14 header "Single-producer, parallel producer, sampled notification"
16 summarize $b "$($RUN_RB_BENCH --rb-sampled $b)"
22 summarize $b-sampled "$($RUN_RB_BENCH --rb-sampled --rb-b2b $b)"
27 summarize "rb-sampled-$b" "$($RUN_RB_BENCH --rb-b2b --rb-batch-cnt $b --rb-sampled --rb-sample-rate $b rb-custom)"
31 summarize "pb-sampled-$b" "$($RUN_RB_BENCH --rb-b2b --rb-batch-cnt $b --rb-sampled --rb-sample-rate $b pb-custom)"
38 header "Ringbuf sampled, reserve+commit vs output"
39 summarize "reserve-sampled" "
[all...] |
| /linux/tools/perf/Documentation/ |
| H A D | perf-report.txt | 130 - code_page_size: the code page size of sampled code address (ip)
136 - addr: (Full) virtual address of the sampled instruction
170 sampled IPC in this function. IPC means Instruction Per Cycle. If it's low,
400 Use the addresses of sampled taken branches instead of the instruction
409 Add the addresses of sampled taken branches to the callstack.
537 When multiple events are sampled, it may not be needed to collect
639 'Sampled Cycles%' - block sampled cycles aggregation / total sampled cycles
640 'Sampled Cycles' - block sampled cycles aggregation
641 'Avg Cycles%' - block average sampled cycles / sum of total block average
642 sampled cycles
[all …]
|
| H A D | perf-evlist.txt | 15 This command displays the names of events sampled in a perf.data file.
|
| H A D | perf-mem.txt | 20 and stores are sampled. Use the -t option to limit to loads or stores.
29 be sampled.
134 - snoop: snoop result for the sampled data access
|
| H A D | perf-arm-spe.txt | 42 Sampling ensures there is only one sampled operation is in flight.
75 hardware. Only one sampled operation is in flight at a time.
89 When an operation is sampled while a previous sampled operation has not finished, a collision
|
| H A D | perf-top.txt | 242 Enable taken branch stack sampling. Any type of taken branch may be sampled.
257 is enabled for all the sampling events. The sampled branch type is the same for all events.
262 Add the addresses of sampled taken branches to the callstack.
|
| /linux/Documentation/input/devices/ |
| H A D | walkera0701.rst | 105 values can be sampled between sync pulses.
118 binary value can be sampled. This bit and magic number is not used in
|
| /linux/Documentation/core-api/ |
| H A D | errseq.rst | 7 point where it was sampled.
22 a flag to tell whether the value has been sampled since a new value was
24 sampled it since the last time an error was recorded.
|
| /linux/Documentation/trace/coresight/ |
| H A D | coresight-cpu-debug.rst | 40 bit width, etc; EDCIDSR is context ID value which contains the sampled value
62 in AArch32 state, EDPCSR is not sampled; when the CPU operates in AArch64
63 state EDPCSR is sampled and no offset are applied.
|
| /linux/Documentation/userspace-api/media/v4l/ |
| H A D | selection-api-intro.rst | 16 cropping target determine the area actually sampled. The sink is an
|
| H A D | crop.rst | 36 the area actually sampled. The target are images read by the application
76 height of the area which can be sampled is given by the ``bounds``
88 the area actually sampled, is given by struct
|
| H A D | selection-api-configuration.rst | 32 areas that can be sampled is given by the ``V4L2_SEL_TGT_CROP_BOUNDS``
38 the area actually sampled, is given by the ``V4L2_SEL_TGT_CROP`` target.
|
| H A D | ext-ctrls-jpeg.rst | 28 input image is sampled, in respect to maximum sample rate in each
|
| H A D | vidioc-cropcap.rst | 84 SECAM, 11/10 for NTSC sampled according to [:ref:`itu601`].
|
| /linux/Documentation/devicetree/bindings/memory-controllers/ |
| H A D | mvebu-devbus.txt | 53 ALE[0] to the cycle that the first read data is sampled
77 last data sampled. Also this parameter has no
|
| /linux/drivers/iio/trigger/ |
| H A D | Kconfig | 52 An experimental trigger, used to allow sensors to be sampled as fast
|