| /linux/Documentation/scsi/ |
| H A D | link_power_management_policy.rst | 13 min_power Enable slumber mode(no partial mode) for the link to
24 state, thus improving latency over min_power setting.
33 min_power_with_partial Same as min_power, but additionally with partial
35 over min_power setting.
|
| /linux/Documentation/translations/zh_CN/scsi/ |
| H A D | link_power_management_policy.rst | 24 min_power 指示控制器在可能的情况下尽量使链路处于最低功耗。
31 而非最低功耗状态，从而改善min_power模式下的延迟。
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-class-scsi_host | 41 min_power: Tell the controller to try to make the link use the
52 improving latency over min_power setting.
58 close to min_power, except that:
|
| /linux/drivers/net/wireless/marvell/mwifiex/ |
| H A D | sta_cmdresp.c | 326 int length, max_power = -1, min_power = -1; in mwifiex_get_power_level() local
343 min_power = pg->power_min; in mwifiex_get_power_level()
351 if (min_power > pg->power_min) in mwifiex_get_power_level()
352 min_power = pg->power_min; in mwifiex_get_power_level()
356 priv->min_tx_power_level = (u8) min_power; in mwifiex_get_power_level()
434 priv->min_tx_power_level = txp->min_power; in mwifiex_ret_rf_tx_power()
|
| H A D | fw.h | 1435 u8 min_power; member
|
| /linux/include/linux/usb/ |
| H A D | musb.h | 94 u8 min_power; member
|
| /linux/drivers/thermal/ |
| H A D | gov_power_allocator.c | 123 u32 min_power; in estimate_sustainable_power() local
130 if (cdev->ops->state2power(cdev, instance->upper, &min_power)) in estimate_sustainable_power()
133 sustainable_power += min_power; in estimate_sustainable_power()
|
| /linux/arch/arm/mach-omap2/ |
| H A D | board-n8x0.c | 74 .min_power = 25, /* x2 = 50 mA drawn from VBUS as peripheral */
|
| /linux/drivers/usb/musb/ |
| H A D | musb_core.h | 355 u8 min_power; /* vbus for periph, in mA/2 */ member
|
| H A D | tusb6010.c | 346 if (x->otg->default_a || mA < (musb->min_power << 1)) in tusb_draw_power()
|
| H A D | musb_core.c | 2331 musb->min_power = plat->min_power; in musb_init_controller()
|
| /linux/drivers/net/wireless/ath/wcn36xx/ |
| H A D | smd.c | 954 u32 min_power = WCN36XX_HAL_DEFAULT_MIN_POWER; in wcn36xx_smd_update_channel_list() local
975 if (min_power > req->channels[i]->max_power) in wcn36xx_smd_update_channel_list()
976 min_power = req->channels[i]->max_power; in wcn36xx_smd_update_channel_list()
981 u32p_replace_bits(¶m->reg_info_1, min_power, in wcn36xx_smd_update_channel_list()
|
| /linux/drivers/net/wireless/ath/ath10k/ |
| H A D | wmi.h | 2061 u8 min_power; member
2089 u32 min_power; member
|
| H A D | mac.c | 1083 arg.channel.min_power = 0; in ath10k_monitor_vdev_start()
1529 arg.channel.min_power = 0; in ath10k_vdev_start_restart()
3460 ch->min_power = 0; in ath10k_update_channel_list()
|
| H A D | wmi.c | 1754 ch->min_power = arg->min_power; in ath10k_wmi_put_wmi_channel()
|
| /linux/drivers/net/wireless/intel/iwlegacy/ |
| H A D | common.h | 481 s8 min_power; /* always 0 */ member
|
| H A D | common.c | 960 ch_info->min_power = 0; in il_init_channel_map()
|
| /linux/drivers/usb/typec/tcpm/ |
| H A D | tcpm.c | 3983 #define min_power(x, y) min(pdo_max_power(x), pdo_max_power(y)) macro
4163 mw = min_power(pdo, matching_snk_pdo); in tcpm_pd_build_request()
|
| /linux/drivers/net/wireless/ath/ath11k/ |
| H A D | wmi.h | 2845 u32 min_power; member
|
| H A D | mac.c | 941 arg.channel.min_power = 0; in ath11k_mac_monitor_vdev_start()
7583 arg.channel.min_power = 0; in ath11k_mac_vdev_start_restart()
|
| /linux/drivers/net/wireless/ath/ath12k/ |
| H A D | wmi.h | 3122 u32 min_power; member
|
| H A D | mac.c | 1346 arg.min_power = 0; in ath12k_mac_monitor_vdev_start()
11169 arg.min_power = 0; in ath12k_mac_vdev_start_restart()
|