| /linux/Documentation/mm/ |
| H A D | multigen_lru.rst | 46 categorized based on additional factors, and a feedback loop can
103 ``folio->flags`` and therefore has a negligible cost. A feedback loop
140 was accessed multiple times through file descriptors and the feedback
142 this end, the feedback loop uses the first tier as the baseline, for
181 Rmap/PT walk feedback
193 forms a feedback loop between the eviction and the aging.
213 A feedback loop modeled after the Proportional-Integral-Derivative
261 * Bloom filters for rmap/PT walk feedback
262 * PID controller for refault feedback
268 Within the eviction, the PID controller uses refaults as the feedback
|
| /linux/Documentation/devicetree/bindings/regulator/ |
| H A D | ltc3589.txt | 14 the resistor values of their external feedback voltage dividers:
18 values R1 and R2 of the feedback voltage divider in ohms.
20 Regulators sw1, sw2, sw3, and ldo2 can regulate the feedback reference from
|
| /linux/drivers/net/ethernet/chelsio/ |
| H A D | Kconfig | 37 Please send feedback to <linux-bugs@chelsio.com>.
64 Please send feedback to <linux-bugs@chelsio.com>.
87 Please send feedback to <linux-bugs@chelsio.com>.
128 Please send feedback to <linux-bugs@chelsio.com>.
|
| /linux/Documentation/input/ |
| H A D | ff.rst | 2 Force feedback for Linux
14 This document describes how to use force feedback devices under Linux. The
18 This document only describes the force feedback part of the Linux input
25 To enable force feedback, you have to:
262 - Status feedback is only supported by iforce driver. If you have
|
| H A D | event-codes.rst | 76 - Used to send force feedback commands to an input device.
84 - Used to receive force feedback device status.
322 EV_FF events are used to initialize a force feedback capable device and to cause
323 such device to feedback.
413 simulated haptic feedback (e.g. a vibrator motor situated below the surface)
414 instead of physical haptic feedback (e.g. a hinge). This property is only set
421 If the simulated haptic feedback is controllable by userspace the device must:
425 - provide the EV_FF FF_HAPTIC force feedback effect.
|
| /linux/Documentation/hwmon/ |
| H A D | max31785.rst | 58 2: Automatic PWM (tach-feedback RPM fan-control)
59 3: Automatic closed-loop (temp-feedback fan-control)
|
| H A D | pm6764tr.rst | 32 under/overvoltage and feedback disconnections.
|
| /linux/Documentation/process/ |
| H A D | contribution-maturity-model.rst | 31 be effective, this evaluation should incorporate feedback from across
98 * Organizations will consider community member feedback in official
106 * Organizations will actively seek out community member feedback as a
|
| /linux/Documentation/admin-guide/acpi/ |
| H A D | cppc_sysfs.rst | 56 * wraparound_time: Minimum time for the feedback counters to wraparound
66 taking two different snapshots of feedback counters at time T1 and T2.
|
| /linux/Documentation/maintainer/ |
| H A D | maintainer-entry-profile.rst | 29 testing feedback that the subsystem uses to gate acceptance?
88 after a patchset has been posted without receiving any feedback. In
92 list how review works for this code area and methods to get feedback
|
| /linux/Documentation/nvdimm/ |
| H A D | maintainer-entry-profile.rst | 9 ...and that instance is configured to give feedback to submitters on
57 In general, please wait up to one week before pinging for feedback. A
|
| /linux/include/uapi/sound/ |
| H A D | asound_fm.h | 44 unsigned char feedback; /* 3 bits: feedback for op0 */ member
|
| /linux/drivers/cpufreq/ |
| H A D | Kconfig.x86 | 182 tristate "AMD frequency sensitivity feedback powersave bias"
187 change decisions based on feedback from hardware (available on AMD
190 Hardware feedback tells software how "sensitive" to frequency changes
345 bool "Current frequency derived from HW provided feedback"
349 provided feedback (as architected counters).
|
| /linux/drivers/crypto/chelsio/ |
| H A D | Kconfig | 20 Please send feedback to <linux-bugs@chelsio.com>.
|
| /linux/drivers/scsi/csiostor/ |
| H A D | Kconfig | 17 Please send feedback to <linux-bugs@chelsio.com>.
|
| /linux/arch/arm/boot/dts/allwinner/ |
| H A D | sunxi-bananapi-m2-plus-v1.2.dtsi | 11 * resistance on the CPU regulator's feedback pin.
|
| /linux/drivers/infiniband/hw/cxgb4/ |
| H A D | Kconfig | 18 Please send feedback to <linux-bugs@chelsio.com>.
|
| /linux/tools/testing/selftests/net/packetdrill/ |
| H A D | tcp_accecn_no_ecn_after_accecn.pkt | 18 // Receive a non ECN SYN-ACK and send a challenge ACK with ACE feedback
|
| /linux/Documentation/devicetree/bindings/sound/ |
| H A D | max98373.txt | 21 - maxim,spkfb-slot-no : slot number used to send speaker feedback information
|
| H A D | cs35l36.txt | 47 polarity of outbound IMON feedback data
50 polarity of outbound VMON feedback data
|
| /linux/arch/arm/boot/dts/samsung/ |
| H A D | exynos3250-artik5-eval.dts | 66 samsung,spi-feedback-delay = <2>;
|
| /linux/drivers/pmdomain/qcom/ |
| H A D | Kconfig | 14 tables based on feedback from the CPR hardware. If you want to do
|
| /linux/Documentation/networking/ |
| H A D | dctcp.rst | 9 the data center network to provide multi-bit feedback to the end hosts.
|
| /linux/Documentation/admin-guide/ |
| H A D | braille-console.rst | 28 Sound feedback can be obtained by adding the ``braille_console.sound=1`` kernel
|
| /linux/drivers/input/ |
| H A D | Kconfig | 42 tristate "Support for memoryless force-feedback devices"
44 Say Y here if you have memoryless force-feedback input device
|