| /linux/tools/testing/selftests/zram/ |
| H A D | README | 5 The zram module creates RAM based block devices named /dev/zram<id>
25 zram01.sh: creates general purpose ram disks with ext4 filesystems
26 zram02.sh: creates block device for swap
|
| /linux/Documentation/driver-api/ |
| H A D | sync_file.rst | 35 the driver creates an out-fence to be able to notify, through
37 Out-fences are fences that the driver creates.
47 When a driver needs to send an out-fence userspace it creates a sync_file.
|
| /linux/Documentation/admin-guide/gpio/ |
| H A D | gpio-mockup.rst | 35 The line above creates three chips. The first one will expose 8 lines,
50 Each mockup chip creates its own subdirectory in /sys/kernel/debug/gpio-mockup/.
|
| /linux/samples/vfio-mdev/ |
| H A D | README.rst | 7 The sample driver creates an mdev device that simulates a serial port over a PCI
12 This step creates a dummy device, /sys/devices/virtual/mtty/mtty/
|
| /linux/Documentation/w1/slaves/ |
| H A D | w1_ds28e17.rst | 22 This driver creates a new I2C bus for any DS28E17 device detected. I2C buses
65 The driver creates sysfs files /sys/bus/w1/devices/19-<id>/speed and
|
| /linux/Documentation/driver-api/hte/ |
| H A D | hte.rst | 59 HTE subsystem creates debugfs attributes at ``/sys/kernel/debug/hte/``.
60 It also creates line/signal-related debugfs attributes at
|
| /linux/arch/arm64/boot/dts/freescale/ |
| H A D | imx8qm-apalis.dtsi | 320 * The PMIC on V1.0A HW generates 1.6V instead of 1.8V which creates
329 * The PMIC on V1.0A HW generates 1.6V instead of 1.8V which creates
|
| /linux/Documentation/arch/x86/ |
| H A D | amd_hsmp.rst | 30 Kconfig option CONFIG_AMD_HSMP_PLAT compiles plat.c and creates amd_hsmp.ko.
31 Kconfig option CONFIG_AMD_HSMP_ACPI compiles acpi.c and creates hsmp_acpi.ko.
33 compiles common code hsmp.c and creates hsmp_common.ko module.
|
| /linux/Documentation/userspace-api/ |
| H A D | dcdbas.rst | 32 The driver creates the following sysfs entries for systems management
59 The driver creates the following sysfs entries for systems management software
|
| /linux/tools/memory-model/litmus-tests/ |
| H A D | dep+plain.litmus | 10 * conditional of P0()'s if-statement creates a control dependency
|
| /linux/tools/testing/selftests/net/packetdrill/ |
| H A D | tcp_fastopen_server_experimental_option.pkt | 24 // Test if FOEXP with a valid cookie creates a TFO socket
|
| /linux/Documentation/admin-guide/mm/damon/ |
| H A D | usage.rst | 41 creates multiple directories and files under its sysfs directory,
122 ``nr_kdamonds``. Writing a number (``N``) to the file creates the number of
186 number (``N``) to the file creates the number of child directories named as
265 number (``N``) to the file creates the number of child directories named ``0``
302 number (``N``) to the file creates the number of child directories named ``0``
332 number (``N``) to the file creates the number of child directories named ``0``
419 number (``N``) to the file creates the number of child directories named ``0``
472 number (``N``) to the file creates the number of child directories named ``0``
528 number (``N``) to the file creates the number of child directories named ``0``
569 that reading it returns the total size of the scheme tried regions, and creates
|
| /linux/drivers/net/ethernet/sunplus/ |
| H A D | Kconfig | 28 The network device creates two net-device interfaces.
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-firmware-opal-powercap | 29 creates a request for setting a new-powercap. The
|
| /linux/Documentation/networking/devlink/ |
| H A D | devlink-health.rst | 26 Device driver creates a "health reporter" per each error/health type.
58 To handle devlink health diagnose and health dump requests, devlink creates a
|
| /linux/drivers/mtd/parsers/ |
| H A D | Kconfig | 25 magic value. This driver does that and creates subpartitions for
103 header and creates up to two partitions, kernel and rootfs.
133 This driver reads partitions table, parses it and creates MTD
|
| /linux/Documentation/hwmon/ |
| H A D | kfan.rst | 23 and control the fan of PLCs and the corresponding cp500 driver creates an
|
| /linux/fs/nilfs2/ |
| H A D | Kconfig | 15 NILFS2 creates a number of checkpoints every few seconds or per
|
| /linux/Documentation/admin-guide/cgroup-v1/ |
| H A D | net_cls.rst | 13 Creating a net_cls cgroups instance creates a net_cls.classid file.
|
| /linux/drivers/char/xillybus/ |
| H A D | Kconfig | 17 its capabilities, and creates device files accordingly.
|
| /linux/Documentation/networking/device_drivers/ethernet/pensando/ |
| H A D | ionic_rdma.rst | 19 initialization and creates auxiliary devices that the ionic_rdma driver
|
| /linux/Documentation/PCI/endpoint/ |
| H A D | pci-ntb-howto.rst | 59 The "mkdir func1" above creates the pci-epf-ntb function device that will
91 The PCI endpoint framework also automatically creates a sub-directory in the
|
| H A D | pci-vntb-howto.rst | 55 The "mkdir func1" above creates the pci-epf-vntb function device that will
87 The PCI endpoint framework also automatically creates a sub-directory in the
|
| /linux/Documentation/misc-devices/ |
| H A D | ibmvmc.rst | 69 basically creates the pipes that enable virtualization management
117 is loaded. It first creates and initializes the CRQ. Next, an exchange of
149 state, EIO will be returned for the ioctl(). The device driver creates a
|
| /linux/Documentation/driver-api/memory-devices/ |
| H A D | ti-emif.rst | 59 The driver creates two debugfs entries per device.
|