| /linux/Documentation/devicetree/bindings/regulator/ |
| H A D | pv88060.txt | 11 BUCK1, LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, SW1, SW2, SW3, SW4,
97 SW3 {
|
| /linux/Documentation/hid/ |
| H A D | hid-alps.rst | 118 1 0 0 SW6 SW5 SW4 SW3 SW2 SW1
168 Byte1 1 1 1 0 1 SW3 SW2 SW1
177 SW1-SW3:
|
| /linux/arch/arm/boot/dts/marvell/ |
| H A D | armada-388-clearfog-base.dts | 23 /* The rear SW3 button */
|
| H A D | armada-388-clearfog.dts | 40 /* The rear SW3 button */
|
| /linux/drivers/regulator/ |
| H A D | cpcap-regulator.c | 336 CPCAP_REG(SW3, CPCAP_REG_S3C, CPCAP_REG_ASSIGN2,
412 CPCAP_REG(SW3, CPCAP_REG_S3C, CPCAP_REG_ASSIGN2,
|
| H A D | pcap-regulator.c | 134 VREG_INFO(SW3, PCAP_REG_SWCTRL, 11, 12, 24, NA),
|
| H A D | pfuze100-regulator.c | 410 PFUZE3000_SW3_REG(PFUZE3000, SW3, PFUZE100_SW3AVOL, 900000, 1650000, 50000),
425 PFUZE3000_SW3_REG(PFUZE3001, SW3, PFUZE100_SW3AVOL, 900000, 1650000, 50000),
|
| H A D | pv88060-regulator.c | 219 PV88060_SW(PV88060, SW3, 5000000),
|
| H A D | ltc3676.c | 227 LTC3676_LINEAR_REG(SW3, sw3, BUCK3, DVB3A),
|
| H A D | ltc3589.c | 256 LTC3589_LINEAR_REG(SW3, sw3, B3DTV1),
|
| H A D | mc13783-regulator.c | 253 MC13783_DEFINE_SW(SW3, sw3, SWITCHERS5, SWITCHERS5, mc13783_sw3_val),
|
| /linux/include/linux/mfd/ |
| H A D | ezx-pcap.h | 131 #define SW3 19 macro
|
| /linux/arch/arm/boot/dts/microchip/ |
| H A D | pm9g45.dts | 180 label = "SW3";
|
| H A D | at91-kizbox3-hs.dts | 86 label = "SW3";
|
| /linux/arch/arm/boot/dts/nxp/imx/ |
| H A D | imx53-qsrb.dts | 58 regulator-name = "SW3";
|
| /linux/arch/arm64/boot/dts/marvell/ |
| H A D | cn9130-cf-base.dts | 29 /* The rear SW3 button */
|
| H A D | cn9130-cf-pro.dts | 29 /* The rear SW3 button */
|
| /linux/arch/arm64/boot/dts/renesas/ |
| H A D | rzg2l-smarc.dtsi | 173 * SW3 should be at position 2->3 so that SER0_RX line is activated
|
| H A D | rzg2lc-smarc.dtsi | 185 * SW3 should be at position 2->3 so that SER0_RX line is activated
|
| /linux/arch/arm/boot/dts/renesas/ |
| H A D | r7s72100-rskrza1.dts | 97 label = "SW3";
|
| H A D | r7s9210-rza2mevb.dts | 60 label = "SW3";
|
| H A D | r8a7740-armadillo800eva.dts | 83 label = "SW3";
|
| H A D | r8a7792-wheat.dts | 62 label = "SW3";
|
| /linux/Documentation/networking/ |
| H A D | arcnet-hardware.rst | 833 SW3 1-8: Node ID Select
849 The eight switches in group SW3 are used to set the node ID. Each node
1999 SW3 1-5: IRQ Select
2009 The eight switches in SW3 are used to set the node ID. Each node attached
2073 *) To enable the Boot ROM set the switch 8 of switch block SW3 to position ON.
2081 Switches 1-5 of the switch block SW3 control the IRQ level::
2096 The switches 6-7 of the switch block SW3 are used to determine the timeout
2852 | SW3 | || | |
2871 SW3 1-5: IRQ Select
2877 Although the jumpers SW1 and SW3 are marked SW, not JP, they are jumpers, not
[all …]
|
| /linux/arch/arm/boot/dts/nxp/mxs/ |
| H A D | imx28-eukrea-mbmx28lc.dtsi | 28 label = "SW3";
|