Home
last modified time | relevance | path

Searched refs:CPM (Results 1 – 23 of 23) sorted by relevance

/linux/Documentation/devicetree/bindings/powerpc/4xx/
H A Dcpm.txt1 PPC4xx Clock Power Management (CPM) node
9 - er-offset : All 4xx SoCs with a CPM controller have
10 one of two different order for the CPM
11 registers. Some have the CPM registers
18 in CPM will be set to turn off unused
22 in CPM will be set to turn off unused
23 devices. This is usually just CPM[CPU].
26 in CPM will be set on standby and
30 in CPM will be set on suspend (mem) and
/linux/drivers/soc/fsl/qe/
H A DKconfig14 coprocessors on Freescale embedded CPUs (akin to CPM in older chips).
37 tristate "CPM/QE TSA support"
40 ((CPM || QUICC_ENGINE) && COMPILE_TEST)
42 Freescale CPM/QE Time Slot Assigner (TSA)
49 tristate "CPM/QE QMC support"
54 Freescale CPM/QE QUICC Multichannel Controller
/linux/Documentation/devicetree/bindings/soc/fsl/cpm_qe/
H A Dcpm.txt7 * Root CPM node
22 * Properties common to multiple CPM/QE devices
25 to specify the device on which a CPM command operates.
38 The multi-user/dual-ported RAM is expressed as a bus under the CPM node.
47 CPM-side offsets with pointer subtraction. It is recommended that
/linux/Documentation/ABI/testing/
H A Dsysfs-bus-platform-devices-ampere-smpro37 …| CPM (core) | 0 | 0 | Snoop-Logic | CPM # …
39 …| CPM (core) | 0 | 2 | Armv8 Core 1 | CPM # …
/linux/arch/powerpc/
H A DKconfig.debug235 bool "Early serial debugging for Freescale CPM-based serial ports"
239 using a CPM-based serial port. This assumes that the bootwrapper
240 has run, and set up the CPM in a particular way.
339 hex "CPM UART early debug transmit descriptor address"
H A DKconfig1135 PPC4xx Clock Power Management (CPM) support (suspend/resume).
/linux/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/
H A Dpincfg.txt24 QE and two options for CPM.
H A Ducc.txt18 CPM UART driver, the port-number is required for the QE UART driver.
/linux/arch/powerpc/platforms/8xx/
H A DKconfig4 select CPM
94 menu "MPC8xx CPM Options"
/linux/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/
H A Di2c.txt3 The I2C controller is expressed as a bus under the CPM node.
/linux/arch/arm64/boot/dts/marvell/
H A Darmada-7020-comexpress.dtsi143 /* CPM Lane 0 - U29 */
H A Darmada-8040-mcbin.dtsi65 /* CON15,16 - CPM lane 4 */
245 /* CPM Lane 5 - U29 */
H A Darmada-7040-db.dts145 * SPI on CPM and NAND have common pins on this board. We can
H A Darmada-cp11x.dtsi477 * this controller is only usable on the CPM
/linux/drivers/pci/controller/
H A Dpcie-xilinx-cpm.c84 CPM, enumerator
635 .version = CPM,
H A DKconfig380 bool "Xilinx Versal CPM PCI controller"
385 Xilinx Versal CPM host bridge.
/linux/arch/powerpc/platforms/
H A DKconfig242 select CPM
262 config CPM config
/linux/drivers/usb/gadget/udc/
H A DKconfig295 tristate "Freescale QE/CPM USB Device Controller"
296 depends on FSL_SOC && (QUICC_ENGINE || CPM)
/linux/arch/arm64/boot/dts/rockchip/
H A Drk3399-gru.dtsi764 * Since our pcie doesn't support ClockPM(CPM), we want
766 * de-assert it along and make ClockPM(CPM) work.
/linux/drivers/tty/serial/
H A DKconfig781 tristate "CPM SCC/SMC serial port support"
789 bool "Support for console on CPM SCC/SMC serial port"
793 Say Y here if you wish to use a SCC or SMC CPM UART as the system
/linux/Documentation/admin-guide/
H A Ddevices.txt2692 46 = /dev/ttyCPM0 PPC CPM (SCC or SMC) - port 0
2694 51 = /dev/ttyCPM5 PPC CPM (SCC or SMC) - port 5
/linux/Documentation/networking/
H A Dbonding.rst2714 A passthrough module (OPM or CPM, optical or copper,
/linux/
H A DMAINTAINERS10189 FREESCALE I2C CPM DRIVER
20348 PCI DRIVER FOR XILINX VERSAL CPM