| /src/sys/contrib/device-tree/Bindings/iio/adc/ |
| H A D | adi,ad7625.yaml | 73 Indicates if EN0 is hard-wired to the high state. If neither this
74 nor en0-gpios are present, then EN0 is hard-wired low.
79 Indicates if EN1 is hard-wired to the high state. If neither this
80 nor en1-gpios are present, then EN1 is hard-wired low.
85 Indicates if EN2 is hard-wired to the high state. If neither this
86 nor en2-gpios are present, then EN2 is hard-wired low.
91 Indicates if EN3 is hard-wired to the high state. If neither this
92 nor en3-gpios are present, then EN3 is hard-wired low.
|
| /src/tools/tools/net80211/scripts/ |
| H A D | config | 21 # Auto-detect WIRED and WIRELESS.
28 test -z "$WIRED" && WIRED=$i
35 test -z "$WIRED" && { echo "No wired device detected!"; exit; }
|
| H A D | setup.tdma-master | 3 # Setup a TDMA master and bridge it to a wired NIC.
16 ifconfig $BRIDGE addm $WLAN addm $WIRED 192.168.2.1/24
18 ifconfig $WIRED up
|
| H A D | setup.simple | 12 ifconfig $BRIDGE addm $WLAN addm $WIRED up
13 ifconfig $WIRED up
|
| H A D | setup.fixed | 13 ifconfig $BRIDGE addm $WLAN addm $WIRED up
14 ifconfig $WIRED up
|
| H A D | setup.updown | 18 ifconfig $BRIDGE addm $WLAN addm $WIRED up
19 ifconfig $WIRED up
|
| H A D | setup.wep | 18 ifconfig $BRIDGE addm $WLAN addm $WIRED up
19 ifconfig $WIRED up
|
| H A D | setup.simple2 | 13 ifconfig $BRIDGE addm $WLAN addm $WIRED up
14 ifconfig $WIRED up
|
| H A D | setup.dfs | 19 ifconfig $BRIDGE addm $WLAN addm $WIRED up
20 ifconfig $WIRED up
|
| H A D | setup.wpa1.tkip | 44 ifconfig $BRIDGE addm $WIRED addm $WLAN up
46 ifconfig $WIRED up
|
| H A D | setup.wpa1.aes | 44 ifconfig $BRIDGE addm $WIRED addm $WLAN up
46 ifconfig $WIRED up
|
| H A D | setup.wpa | 44 ifconfig $BRIDGE addm $WIRED addm $WLAN up
46 ifconfig $WIRED up
|
| H A D | setup.wpa2 | 45 ifconfig $BRIDGE addm $WIRED addm $WLAN up
47 ifconfig $WIRED up
|
| H A D | setup.tsn | 46 ifconfig $BRIDGE addm $WIRED addm $WLAN up
48 ifconfig $WIRED up
|
| H A D | setup.wpa2.tkip | 45 ifconfig $BRIDGE addm $WIRED addm $WLAN up
47 ifconfig $WIRED up
|
| H A D | setup.updown.wpa | 43 ifconfig $BRIDGE addm $WIRED addm $WLAN up
45 # ifconfig $WIRED up
|
| /src/share/man/man9/ |
| H A D | pmap_unwire.9 | 43 removes the wired attribute from each of the virtual-to-physical page mappings
50 Every valid mapping within that range is required to have the wired attribute
52 Invalid mappings are ignored, since they cannot have the wired attribute set.
56 can be used to set the wired attribute of a virtual-to-physical page mapping.
|
| /src/sys/contrib/device-tree/Bindings/interrupt-controller/ |
| H A D | img,pdc-intc.txt | 82 * An SoC peripheral that is wired through the PDC.
85 // The interrupt controller that this device is wired to.
96 * An interrupt generating device that is wired to a SysWake pin.
99 // The interrupt controller that this device is wired to.
|
| /src/sys/contrib/device-tree/Bindings/iommu/ |
| H A D | riscv,iommu.yaml | 19 Hardware uses in-memory command and fault reporting queues with wired
62 Wired interrupt vectors available for RISC-V IOMMU to notify the
80 /* Example 1 (IOMMU device with wired interrupts) */
100 /* Example 2 (IOMMU device with shared wired interrupt) */
|
| /src/sys/contrib/device-tree/src/arm/allwinner/ |
| H A D | sun8i-v3s-anbernic-rg-nano.dts | 183 /* DCDC2 wired into vdd-cpu, vdd-sys, and vdd-ephy. */
191 /* DCDC3 wired into every 3.3v input that isn't the RTC. */
199 /* LDO1 wired into RTC, voltage is hard-wired at 3.3v. */
205 /* LDO2 wired into VCC-PLL and audio codec. */
|
| /src/sys/contrib/device-tree/Bindings/iio/resolver/ |
| H A D | adi,ad2s1210.yaml | 44 Note on SPI connections: The CS line on the AD2S1210 should hard-wired to
105 RES0 and RES1 pins are hard-wired to match the assigned-resolution-bits
120 This is used to indicate the selected mode if A0 and A1 are hard-wired
130 RES1 are hard-wired to match this value.
|
| /src/contrib/wpa/wpa_supplicant/systemd/ |
| H A D | wpa_supplicant-wired.service.arg.in | 2 Description=WPA supplicant daemon (interface- and wired driver-specific version)
12 ExecStart=@BINDIR@/wpa_supplicant -c/etc/wpa_supplicant/wpa_supplicant-wired-%I.conf -Dwired -i%I
|
| /src/share/man/man4/ |
| H A D | scsi.4 | 204 .Em wired
209 Units are wired down by setting kernel environment hints.
222 bus numbers can be wired down to specific controllers with
244 Peripheral drivers can be wired to a specific bus, target, and lun as so:
259 wired to any particular controller, bus, target, and/or unit instance.
285 For devices that provide a serial number, units may be wired to that serial
|
| /src/sys/contrib/device-tree/Bindings/media/ |
| H A D | st-rc.txt | 12 be present iff the rx pins are wired up.
15 be present iff the tx pins are wired up.
|
| /src/sys/contrib/device-tree/Bindings/spi/ |
| H A D | spi-peripheral-props.yaml | 93 description: Several SPI memories can be wired in stacked mode.
105 description: Several SPI memories can be wired in parallel mode.
111 many busses as devices must be wired. The size of each chip should
|