Searched full:told (Results 1 – 25 of 212) sorted by relevance
123456789
| /linux-6.8/fs/xfs/ |
| D | xfs_pwork.h | 37 /* Have we been told to abort? */
45 /* Have we been told to abort? */
|
| /linux-6.8/drivers/usb/serial/ |
| D | wishbone-serial.c | 25 * Etherbone must be told that a new stream has begun before data arrives.
27 * Similarly, when the stream ends, Etherbone must be told so that the cycle
|
| /linux-6.8/sound/hda/ |
| D | Kconfig | 61 to using the old SST driver, unless told otherwise through the
|
| /linux-6.8/Documentation/admin-guide/nfs/ |
| D | nfsd-admin-interfaces.rst | 14 Before doing that, NFSD can be told which sockets to listen on by
|
| /linux-6.8/arch/arm/mach-omap2/ |
| D | clockdomain.h | 111 * @wkdep_srcs: Clockdomains that can be told to wake this powerdomain up
112 * @sleepdep_srcs: Clockdomains that can be told to keep this clkdm from inact
|
| /linux-6.8/drivers/parport/ |
| D | probe.c | 199 printk(KERN_DEBUG "%s: Device ID was %zd bytes while device told it would be %d bytes\n", in parport_read_device_id()
210 …printk(KERN_DEBUG "%s: Device ID reading stopped before device told data not available. Current id… in parport_read_device_id()
|
| /linux-6.8/include/scsi/ |
| D | scsi_status.h | 50 DID_ABORT = 0x05, /* Told to abort for some other reason */
|
| /linux-6.8/drivers/usb/storage/ |
| D | unusual_datafab.h | 21 * I'm told they exist but so far nobody has come forward to say that
|
| /linux-6.8/Documentation/input/devices/ |
| D | bcm5974.rst | 44 with the HID driver, which, if not told otherwise, will find the standard
|
| /linux-6.8/Documentation/fb/ |
| D | sh7760fb.rst | 48 The LCDC must explicitly be told about the type of LCD panel
|
| /linux-6.8/arch/sparc/include/asm/ |
| D | switch_to_32.h | 51 * holding certain values, gcc is told that they are clobbered.
|
| /linux-6.8/Documentation/block/ |
| D | writeback_cache_control.rst | 80 to be told to pass through the REQ_FUA bit using::
|
| /linux-6.8/drivers/video/fbdev/ |
| D | n411.c | 135 /* if we were told to splash the screen, we just clear it */ in n411_init_board()
|
| D | arcfb.c | 20 * existence of the LCD so it must be told at load time whether it should
516 /* if we were told to splash the screen, we just clear it */ in arcfb_probe()
|
| /linux-6.8/Documentation/filesystems/ |
| D | ocfs2.rst | 77 commit=nrsec (*) Ocfs2 can be told to sync all its data and metadata
|
| /linux-6.8/arch/x86/xen/ |
| D | platform-pci-unplug.c | 151 * but the user told us that unplugging is unnecessary. */ in xen_unplug_emulated_devices()
|
| /linux-6.8/drivers/net/arcnet/ |
| D | com20020-isa.c | 48 * it's where we were told it was, and even do autoirq.
|
| /linux-6.8/Documentation/networking/ |
| D | tipc.rst | 87 (before Linux 4.17) and told which interface to attach to. The "tipc"
|
| /linux-6.8/Documentation/admin-guide/laptops/ |
| D | disk-shock-protection.rst | 114 laptop or the hard drive itself told you so), then you can tell the
|
| /linux-6.8/Documentation/trace/ |
| D | intel_th.rst | 113 The driver needs to be told that such an arrangement is taking place
|
| /linux-6.8/Documentation/process/ |
| D | researcher-guidelines.rst | 158 (This is required if you have been explicitly told your patches need
|
| /linux-6.8/arch/x86/kernel/ |
| D | tsc_msr.c | 227 * TSC is reliable. We were told by silicon design team that TSC in cpu_khz_from_msr()
|
| /linux-6.8/arch/arc/kernel/ |
| D | entry-arcv2.S | 183 # But irq tracer needs to be told now...
|
| /linux-6.8/drivers/rtc/ |
| D | rtc-opal.c | 222 * explicitly told to opal. in opal_tpo_alarm_irq_enable()
|
| /linux-6.8/drivers/usb/host/ |
| D | ohci-sm501.c | 154 * using kmalloc() - so the usb core needs to be told that it must copy in ohci_hcd_sm501_drv_probe()
|
123456789