Searched full:strapped (Results 1 – 22 of 22) sorted by relevance
| /linux-5.10/Documentation/devicetree/bindings/net/ ! |
| D | ti,dp83822.yaml | 36 This property is only applicable if the fiber mode support is strapped
44 Fiber mode support can also be strapped. If the strap pin is not set
46 If the fiber mode is not strapped then signal detection for the PHY
|
| D | ti,dp83867.yaml | 91 This denotes the fact that the board has RX_DV/RX_CTRL pin strapped in
93 software needs to take when this pin is strapped in these modes.
|
| /linux-5.10/Documentation/devicetree/bindings/pci/ ! |
| D | fsl,pci.txt | 3 Typically any Freescale PCI-X bridge hardware strapped into Agent mode
9 enumeration despite being strapped into Agent mode.
|
| /linux-5.10/Documentation/devicetree/bindings/mfd/ ! |
| D | bd9571mwv.txt | 40 strapped low).
43 is strapped high).
|
| /linux-5.10/Documentation/devicetree/bindings/display/panel/ ! |
| D | tpo,tpg110.yaml | 16 driver is strapped up in electronics to the desired resolution
18 SPI. By talking to the TPG110 over SPI, the strapped properties
|
| /linux-5.10/drivers/usb/cdns3/ ! |
| D | drd.c | 382 dev_dbg(cdns->dev, "Controller strapped to HOST\n"); in cdns3_drd_init()
385 dev_dbg(cdns->dev, "Controller strapped to PERIPHERAL\n"); in cdns3_drd_init()
|
| /linux-5.10/drivers/net/dsa/mv88e6xxx/ ! |
| D | smi.c | 14 * (ADDR[0] is always zero, thus only even SMI addresses can be strapped).
|
| /linux-5.10/drivers/net/phy/ ! |
| D | dp83822.c | 475 * SD_EN pins are strapped. Signal detection can only enabled if FX_EN in dp83822_of_init()
476 * is strapped otherwise signal detection is disabled for the PHY. in dp83822_of_init()
|
| D | dp83867.c | 612 /* Force speed optimization for the PHY even if it strapped */ in dp83867_config_init()
622 /* RX_DV/RX_CTRL strapped in mode 1 or mode 2 workaround */ in dp83867_config_init()
|
| D | dp83869.c | 752 /* Force speed optimization for the PHY even if it strapped */ in dp83869_config_init()
|
| D | broadcom.c | 484 /* The PHY is strapped in RGMII-fiber mode when INTERF_SEL[1:0] in bcm54616s_probe()
|
| /linux-5.10/drivers/char/hw_random/ ! |
| D | bcm2835-rng.c | 44 /* MIPS chips strapped for BE will automagically configure the in rng_readl()
|
| /linux-5.10/drivers/irqchip/ ! |
| D | irq-brcmstb-l2.c | 204 /* MIPS chips strapped for BE will automagically configure the in brcmstb_l2_intc_of_init()
|
| D | irq-bcm7120-l2.c | 268 /* MIPS chips strapped for BE will automagically configure the in bcm7120_l2_intc_probe()
|
| /linux-5.10/drivers/net/mdio/ ! |
| D | mdio-bcm-unimac.c | 51 /* MIPS chips strapped for BE will automagically configure the in unimac_mdio_readl()
|
| /linux-5.10/sound/soc/codecs/ ! |
| D | zl38060.c | 14 // - chip must be strapped for "host boot": in this mode, firmware will be
|
| /linux-5.10/drivers/net/ethernet/broadcom/genet/ ! |
| D | bcmgenet.h | 709 /* MIPS chips strapped for BE will automagically configure the \
|
| D | bcmgenet.c | 73 /* MIPS chips strapped for BE will automagically configure the in bcmgenet_writel()
|
| /linux-5.10/drivers/mtd/spi-nor/controllers/ ! |
| D | aspeed-smc.c | 621 * The first chip of the AST2500 FMC flash controller is strapped by
|
| /linux-5.10/drivers/edac/ ! |
| D | i5100_edac.c | 1008 /* figure out how many ranks, from strapped state of 48GB_Mode input */ in i5100_init_one()
|
| /linux-5.10/sound/oss/dmasound/ ! |
| D | dmasound_core.c | 585 /* FIXME: I think that this may be the wrong behaviour when we get strapped in sq_write()
|
| /linux-5.10/drivers/gpu/drm/i2c/ ! |
| D | tda998x_drv.c | 1946 * is at the TDA9950 address, with the address pins strapped across in tda998x_create()
|