Searched full:squelch (Results 1 – 25 of 33) sorted by relevance
12
| /linux-6.8/include/linux/phy/ |
| D | phy-sun4i-usb.h | 12 * sun4i_usb_phy_set_squelch_detect() - Enable/disable squelch detect
14 * @enabled: wether to enable or disable squelch detect
|
| /linux-6.8/Documentation/devicetree/bindings/phy/ |
| D | phy-stm32-usbphyc.yaml | 158 st,tune-squelch-level:
160 Tunes the squelch DC threshold value
259 st,tune-squelch-level = <3>;
277 st,tune-squelch-level = <3>;
|
| D | qcom,usb-snps-femto-v2.yaml | 74 qcom,squelch-detector-bp:
|
| D | nvidia,tegra20-usb-phy.yaml | 193 description: HS squelch detector level.
|
| /linux-6.8/drivers/phy/marvell/ |
| D | phy-mvebu-cp110-utmi.c | 139 /* Disable SQ and enable analog squelch detect */ in mvebu_cp110_utmi_port_setup()
146 * Set External squelch calibration number and in mvebu_cp110_utmi_port_setup()
147 * enable the External squelch calibration in mvebu_cp110_utmi_port_setup()
|
| D | phy-mvebu-a3700-utmi.c | 145 /* Wait for squelch calibration */ in mvebu_a3700_utmi_phy_power_on()
|
| /linux-6.8/Documentation/networking/device_drivers/hamradio/ |
| D | baycom.rst | 136 ser12 if software DCD is utilised, the radio's squelch should always be
138 as it is much faster than most hardware squelch circuitry. The
|
| D | z8530drv.rst | 620 slow squelch.
|
| /linux-6.8/arch/arm/boot/dts/st/ |
| D | stm32mp135f-dk.dts | 344 st,tune-squelch-level = <1>;
358 st,tune-squelch-level = <1>;
|
| D | stm32mp157c-ev1.dts | 394 st,tune-squelch-level = <3>;
410 st,tune-squelch-level = <3>;
|
| D | stm32mp15xx-dkx.dtsi | 718 st,tune-squelch-level = <3>;
730 st,tune-squelch-level = <3>;
|
| /linux-6.8/drivers/net/ethernet/broadcom/bnxt/ |
| D | bnxt_hwrm.h | 19 BNXT_HWRM_CTX_SILENT = BIT(2), /* squelch firmware errors */
|
| /linux-6.8/drivers/phy/st/ |
| D | phy-stm32-usbphyc.c | 526 ret = of_property_read_u32(np, "st,tune-squelch-level", &val); in stm32_usbphyc_phy_tuning()
531 dev_warn(usbphyc->dev, "phy%d: invalid st,tune-squelch\n", index); in stm32_usbphyc_phy_tuning()
|
| /linux-6.8/arch/x86/platform/olpc/ |
| D | olpc.c | 241 * Squelch SCIs while suspended. This is a fix for in olpc_xo1_ec_suspend()
|
| /linux-6.8/drivers/ata/ |
| D | ahci_tegra.c | 334 /* For SQUELCH Filter & Gen3 drive getting detected as Gen1 drive */ in tegra_ahci_controller_init()
|
| /linux-6.8/drivers/phy/qualcomm/ |
| D | phy-qcom-snps-femto-v2.c | 328 "qcom,squelch-detector-bp",
|
| /linux-6.8/arch/arm64/boot/dts/qcom/ |
| D | sc7280-idp.dtsi | 536 qcom,squelch-detector-bp = <(-2090)>;
|
| D | qcm6490-fairphone-fp5.dts | 906 qcom,squelch-detector-bp = <(-2090)>;
|
| D | sc7280-herobrine.dtsi | 653 qcom,squelch-detector-bp = <(-2090)>;
|
| /linux-6.8/drivers/hid/ |
| D | hid-ntrig.c | 517 case HID_DG_CONTACTID: /* Not trustworthy, squelch for now */ in ntrig_input_mapping()
|
| /linux-6.8/drivers/net/hamradio/ |
| D | baycom_ser_hdx.c | 298 * PLL algorithm for the hardware squelch DCD algorithm in ser12_rx()
|
| /linux-6.8/drivers/scsi/mvsas/ |
| D | mv_94xx.c | 108 /* R10Ch DFE Resolution Control/Squelch and FFE Setting in set_phy_ffe_tuning()
|
| /linux-6.8/include/linux/soundwire/ |
| D | sdw.h | 676 * @is_mockup_device: status flag used to squelch errors in the command/control
|
| /linux-6.8/drivers/net/ethernet/smsc/ |
| D | smc91x.h | 753 #define PHY_CFG1_RLVL0 0x0040 // 1=Rx Squelch level reduced by 4.5db
|
| /linux-6.8/drivers/infiniband/hw/qib/ |
| D | qib_sd7220.c | 242 /* Squelch possible parity error from _asserting_ reset */ in qib_ibsd_reset()
|
12