Searched full:sequencing (Results 1 – 25 of 67) sorted by relevance
123
| /linux-5.10/Documentation/devicetree/bindings/mfd/ |
| D | max77620.txt | 34 and power-down delays (sequencing). GPIO1, GPIO2, and GPIO3 can be programmed
39 The flexible sequencing structure consists of two hardware enable inputs
40 (EN0, EN1), and 3 master sequencing timers called FPS0, FPS1 and FPS2.
41 Each master sequencing timer is programmable through its configuration
43 source (SW). When enabled/disabled, the master sequencing timer generates
44 eight sequencing events on different time periods called slots. The time
55 clock are set into following state at the sequencing event that
59 the sequencing event.
61 low power mode at the sequencing event.
|
| /linux-5.10/Documentation/i2c/busses/ |
| D | i2c-ali1535.rst | 27 Additionally, the sequencing of the SMBus transactions has been modified to
28 be more consistent with the sequencing recommended by the manufacturer and
|
| /linux-5.10/Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-max77620.txt | 64 - maxim,active-fps-power-up-slot: Sequencing event slot number on which
71 - maxim,active-fps-power-down-slot: Sequencing event slot number on which
|
| /linux-5.10/Documentation/devicetree/bindings/arm/freescale/ |
| D | fsl,imx7ulp-pm.yaml | 13 The Multi-System Mode Controller (MSMC) is responsible for sequencing
|
| /linux-5.10/Documentation/devicetree/bindings/display/panel/ |
| D | raspberrypi,7inch-touchscreen.yaml | 17 - Atmel microcontroller on I2C for power sequencing the DSI bridge and
|
| /linux-5.10/Documentation/devicetree/bindings/input/ |
| D | hid-over-i2c.txt | 22 power sequencing. The following properties can be supported by one or more
|
| /linux-5.10/Documentation/devicetree/bindings/regulator/ |
| D | regulator-max77620.txt | 62 - maxim,active-fps-power-up-slot: Sequencing event slot number on which
69 - maxim,active-fps-power-down-slot: Sequencing event slot number on which
|
| /linux-5.10/Documentation/filesystems/ |
| D | xfs-delayed-logging-design.rst | 419 Delayed Logging: Checkpoint Sequencing
434 written directly into the log buffers. Hence some other method of sequencing
672 that is run as part of the checkpoint commit and log force sequencing. The code
678 sequencing also requires the same lock, list walk, and blocking mechanism to
681 These two sequencing operations can use the mechanism even though the
683 sequencing needs to wait until checkpoint contexts contain a commit LSN
685 sequencing needs to wait until previous checkpoint contexts are removed from
|
| /linux-5.10/Documentation/devicetree/bindings/power/ |
| D | fsl,imx-gpcv2.yaml | 62 power-up sequencing to ensure reset propagation into devices located
|
| D | fsl,imx-gpc.yaml | 70 power-up sequencing to ensure reset propagation into devices located
|
| /linux-5.10/net/l2tp/ |
| D | l2tp_core.h | 64 * Tracks runtime state including cookies, dataplane packet sequencing, and IO statistics.
253 /* Receive path helpers. If data sequencing is enabled for the session these
|
| /linux-5.10/Documentation/driver-api/nvdimm/ |
| D | firmware-activate.rst | 79 The last runtime activation failed due to a sequencing error of the
|
| /linux-5.10/include/scsi/ |
| D | libiscsi.h | 171 /* iSCSI connection-wide sequencing */
274 /* iSCSI session-wide sequencing */
|
| /linux-5.10/arch/arm/boot/dts/ |
| D | stm32mp15xx-dhcom-drc02.dtsi | 60 * This signal should be handled by USB power sequencing in
|
| /linux-5.10/drivers/hwmon/pmbus/ |
| D | max34440.c | 227 * 0x10: Sequencing + voltage monitoring (only valid for PAGES 0–11) in max34451_set_supported_funcs()
228 * 0x20: Voltage monitoring (no sequencing) in max34451_set_supported_funcs()
|
| /linux-5.10/drivers/i2c/busses/ |
| D | i2c-ali1535.c | 18 the sequencing of the SMBus transactions has been modified
19 to be more consistent with the sequencing recommended by
|
| /linux-5.10/net/sunrpc/auth_gss/ |
| D | gss_krb5_unseal.c | 132 /* do sequencing checks */ in gss_verify_mic_v1()
|
| D | gss_krb5_wrap.c | 326 /* do sequencing checks */ in gss_unwrap_kerberos_v1()
530 /* do sequencing checks */ in gss_unwrap_kerberos_v2()
|
| /linux-5.10/drivers/mtd/nand/raw/ |
| D | nand_bch.c | 163 * FIXME: we should probably rework the sequencing in nand_scan_tail() in nand_bch_init()
|
| /linux-5.10/drivers/pci/controller/cadence/ |
| D | pci-j721e.c | 402 * "Power Sequencing and Reset Signal Timings" table in in j721e_pcie_probe()
|
| /linux-5.10/Documentation/hwmon/ |
| D | it87.rst | 228 for AMD power sequencing. Therefore the chip will appear as IT8716F
|
| /linux-5.10/drivers/clk/qcom/ |
| D | gdsc.c | 333 * Disable SW override: Use hardware state-machine for sequencing. in gdsc_init()
|
| /linux-5.10/block/ |
| D | blk-flush.c | 198 * flush sequencing and may already have gone through the in blk_flush_complete_seq()
|
| /linux-5.10/Documentation/sound/soc/ |
| D | dpcm.rst | 343 unless your HW needs more fine grained sequencing of the PCM ops.
|
| /linux-5.10/drivers/gpu/drm/gma500/ |
| D | intel_bios.c | 76 /* Get the eDP sequencing and link info */ in parse_edp()
|
123