Searched full:routers (Results 1 – 25 of 62) sorted by relevance
123
| /linux-5.10/include/linux/ |
| D | pim.h | 21 * 0 = Hello Multicast to ALL-PIM-ROUTERS
25 * 3 = Join/Prune Multicast to ALL-PIM-ROUTERS
26 * 4 = Bootstrap Multicast to ALL-PIM-ROUTERS
27 * 5 = Assert Multicast to ALL-PIM-ROUTERS
|
| /linux-5.10/net/atm/ |
| D | Kconfig | 54 Multi-Protocol Over ATM allows ATM edge devices such as routers,
56 subnetwork boundaries. These shortcut connections bypass routers
|
| /linux-5.10/Documentation/netlabel/ |
| D | draft-ietf-cipso-ipsecurity-01.txt | 281 Routers work most efficiently when processing fixed length fields. To
282 support these routers there is an optimized form of tag type 1. The format
431 gateways, and routers that support multiple sensitivity labels. A CIPSO
452 parameter does not apply to CIPSO gateways or routers. This parameter need
470 not apply to CIPSO gateways or routers. This parameter need not be defined
517 MAY be in CIPSO or local format. Some CIPSO systems, such as routers, may
683 routers.
|
| /linux-5.10/arch/arm/mach-bcm/ |
| D | Kconfig | 79 This is a network SoC line mostly used in home routers and
179 This SoC line is mostly used in home routers and is some cheaper
|
| /linux-5.10/Documentation/networking/device_drivers/appletalk/ |
| D | ltpc.rst | 48 attached to a network that includes AppleTalk routers or not. If,
64 If you are attached to an extended AppleTalk network, with routers on
|
| /linux-5.10/drivers/thunderbolt/ |
| D | sb_regs.h | 3 * USB4 port sideband registers found on routers and retimers
|
| D | usb4.c | 257 * USB4 routers need additional settings in order to enable all the
388 * established with the upstream router. Call only for device routers.
420 * child routers). For device routers do this also for the in usb4_switch_set_wake()
453 * needed for device routers. in usb4_switch_set_wake()
779 * USB4 routers have direct mapping between USB4 ports and PCIe
810 * USB4 routers have direct mapping between USB4 ports and USB 3.x
|
| D | tb.c | 26 * @remove_work: Work used to remove any unplugged routers after
880 * This should bring the routers in the middle active as well in tb_tunnel_dp()
1297 /* All USB4 routers support runtime PM */ in tb_start()
|
| /linux-5.10/drivers/firmware/broadcom/ |
| D | Kconfig | 6 Broadcom home routers contain flash partition called "nvram" with all
|
| /linux-5.10/Documentation/devicetree/bindings/dma/ |
| D | dma-router.yaml | 16 DMA routers are transparent IP blocks used to route DMA request
|
| /linux-5.10/Documentation/devicetree/bindings/mtd/partitions/ |
| D | brcm,bcm947xx-cfe-partitions.txt | 5 home routers. Their BCM947xx boards using CFE bootloader have several partitions
|
| /linux-5.10/include/uapi/linux/ |
| D | ipv6_route.h | 22 fallback, no routers on link */
|
| /linux-5.10/arch/ia64/include/asm/uv/ |
| D | uv_hub.h | 32 * routers always have low bit of 1, C/MBricks have low bit
71 * includes all C & M bricks. Routers are NOT included.
|
| /linux-5.10/Documentation/driver-api/gpio/ |
| D | using-gpio.rst | 15 laptops, phones, tablets, routers, and any consumer or office or business goods
|
| /linux-5.10/include/linux/mtd/ |
| D | partitions.h | 24 * embedded subpartitions / volumes. E.g. many home routers use "firmware"
|
| /linux-5.10/drivers/net/wireless/ath/ath9k/ |
| D | Kconfig | 171 These devices are usually various network appliances, routers or
|
| /linux-5.10/Documentation/networking/ |
| D | ila.rst | 89 network; these are provided by "ILA hosts" and "ILA routers" respectively.
94 as showing ILA hosts and routers::
|
| D | decnet.rst | 156 - If you have any DECnet routers on your network, they should appear
|
| /linux-5.10/drivers/net/ethernet/8390/ |
| D | Kconfig | 96 some SnapGear routers do as well.
|
| /linux-5.10/net/ipv4/netfilter/ |
| D | nf_reject_ipv4.c | 162 * some routers/firewalls, and they drop the packet. So we need to in nf_send_reset()
|
| /linux-5.10/net/ipv6/netfilter/ |
| D | nf_reject_ipv6.c | 217 * some routers/firewalls, and they drop the packet. So we need to in nf_send_reset6()
|
| /linux-5.10/arch/x86/include/asm/uv/ |
| D | uv_hub.h | 42 * routers always have low bit of 1, C/MBricks have low bit
113 * includes all C & M bricks. Routers are NOT included.
|
| /linux-5.10/net/ipv4/ |
| D | ip_gre.c | 68 2. Networking dead loops would not kill routers, but would really
79 true router now :-)), all routers (at least, in neighbourhood of mine)
123 /* All the routers (except for Linux) return only in ipgre_err()
214 /* All the routers (except for Linux) return only in gre_err()
|
| /linux-5.10/arch/mips/sgi-ip27/ |
| D | ip27-memory.c | 104 /* Figure out which routers nodes in question are connected to */ in compute_node_distance()
|
| /linux-5.10/drivers/net/usb/ |
| D | cx82310_eth.c | 3 * Driver for USB ethernet port of Conexant CX82310-based ADSL routers
|
123