| /linux/Documentation/devicetree/bindings/leds/ |
| H A D | richtek,rt8515.yaml | 15 current for each mode is defined in hardware using two resistors
34 resistors limits the maximum flash current. This must be set
43 resistors limits the maximum torch current. This must be set
|
| /linux/Documentation/devicetree/bindings/usb/ |
| H A D | ti,tusb73x0-pci.yaml | 28 PWRONx# pins are active high and their internal pull-down resistors are
30 and their internal pull-down resistors are enabled.
|
| /linux/drivers/rtc/ |
| H A D | rtc-ds1343.c | 147 char *diodes = "disabled", *resistors = " "; in ds1343_show_tricklecharger() local
166 resistors = "1k Ohm"; in ds1343_show_tricklecharger()
170 resistors = "2k Ohm"; in ds1343_show_tricklecharger()
174 resistors = "4k Ohm"; in ds1343_show_tricklecharger()
183 return sprintf(buf, "%s %s\n", diodes, resistors); in ds1343_show_tricklecharger()
|
| H A D | rtc-ds1305.c | 386 char *resistors = ""; in ds1305_proc() local
402 resistors = "2k Ohm"; in ds1305_proc()
405 resistors = "4k Ohm"; in ds1305_proc()
408 resistors = "8k Ohm"; in ds1305_proc()
417 seq_printf(seq, "trickle_charge\t: %s%s\n", diodes, resistors); in ds1305_proc()
|
| /linux/Documentation/hwmon/ |
| H A D | ina3221.rst | 48 value for their shunt resistors)
53 value for their shunt resistors)
|
| H A D | w83l785ts.rst | 25 of external resistors, so the user cannot change it. Values seen so
|
| H A D | ltc4260.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
|
| /linux/Documentation/devicetree/bindings/mfd/ |
| H A D | adi,adp5585.yaml | 23 - adi,adp5585-02 # No pull-up resistors by default on special pins
25 - adi,adp5585-04 # Pull-down resistors on all pins by default
31 - adi,adp5589-02 # Pull-down resistors by default on special pins
|
| /linux/drivers/gpu/drm/nouveau/nvkm/subdev/bios/ |
| H A D | iccsense.c | 122 rail->resistors[r].mohm = nvbios_rd08(bios, entry + res_start + r * 2); in nvbios_iccsense_parse()
123 rail->resistors[r].enabled = !(nvbios_rd08(bios, entry + res_start + r * 2 + 1) & 0x40); in nvbios_iccsense_parse()
|
| /linux/Documentation/devicetree/bindings/hwmon/ |
| H A D | ntc-thermistor.yaml | 12 Thermistors with negative temperature coefficient (NTC) are resistors that
59 We can use both pull-up and pull-down resistors at the same time, and then
|
| H A D | adi,ltc2991.yaml | 16 sense resistors or temperature sensing transistors.
|
| /linux/drivers/gpu/drm/nouveau/include/nvkm/subdev/bios/ |
| H A D | iccsense.h | 13 struct pwr_rail_resistor_t resistors[3]; member
|
| /linux/drivers/input/serio/ |
| H A D | parkbd.c | 33 * The diodes can be fairly any type, and the resistors should be somewhere
34 * around 5 kOhm, but the adapter will likely work without the resistors,
|
| /linux/include/linux/platform_data/ |
| H A D | st_sensors_pdata.h | 21 * @pullups: enable/disable i2c controller pullup resistors.
|
| /linux/Documentation/devicetree/bindings/net/ |
| H A D | motorcomm,yt8xxx.yaml | 59 be configured with hardware pull-up resistors to match the SOC voltage
76 be configured with hardware pull-up resistors to match the SOC voltage
|
| H A D | ethernet-phy.yaml | 247 supported by the builtin resistors of the PHY, otherwise the resistors may
|
| /linux/Documentation/devicetree/bindings/pinctrl/ |
| H A D | mediatek,mt6795-pinctrl.yaml | 133 Pull up settings for 2 pull resistors, R0 and R1. User can
145 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| H A D | mediatek,mt6779-pinctrl.yaml | 162 Pull up settings for 2 pull resistors, R0 and R1. User can
174 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| H A D | mediatek,mt8183-pinctrl.yaml | 146 Pull up settings for 2 pull resistors, R0 and R1. User can
158 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| H A D | mediatek,mt8365-pinctrl.yaml | 152 Pull up settings for 2 pull resistors, R0 and R1. User can
166 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| /linux/include/linux/usb/ |
| H A D | isp116x.h | 11 /* Enable internal resistors on downstream ports */
|
| H A D | isp1362.h | 11 /* Enable internal pulldown resistors on downstream ports */
|
| /linux/Documentation/devicetree/bindings/gpio/ |
| H A D | exar,xra1403.yaml | 17 - Internal pull-up resistors
|
| /linux/arch/sh/drivers/pci/ |
| H A D | fixups-sdk7786.c | 21 * resistors to determine card presence. Hotplug remains unsupported.
|
| /linux/Documentation/devicetree/bindings/power/supply/ |
| H A D | richtek,rt9467.yaml | 18 integrated sensing resistors.
|