| /linux-6.8/Documentation/driver-api/driver-model/ ! |
| D | driver.rst | 191 devices of the device have successfully probed. The list of consumers of the
198 point in time have already probed successfully, sync_state() is called right
200 too is considered as "all consumers of the device have probed" and sync_state()
204 still consumers that haven't probed successfully, the sync_state() call is
207 there are one or more consumers of the device that haven't probed yet, then
214 consumers of the device have probed. Once all the consumers of the device have
215 probed, the device's driver can synchronize the hardware state of the device to
224 probed.
229 all the consumers of a device have probed::
|
| /linux-6.8/sound/soc/ ! |
| D | soc-card.c | 183 * So, set "probed" flag here, because it needs to care in snd_soc_card_probe()
190 card->probed = 1; in snd_soc_card_probe()
208 * This means, we can set "card->probed" flag afer "late_probe" in snd_soc_card_late_probe()
215 card->probed = 1; in snd_soc_card_late_probe()
230 if (card->probed && in snd_soc_card_remove()
234 card->probed = 0; in snd_soc_card_remove()
|
| /linux-6.8/include/soc/fsl/ ! |
| D | bman.h | 130 * bman_is_probed - Check if bman is probed
132 * Returns 1 if the bman driver successfully probed, -1 if the bman driver
133 * failed to probe or 0 if the bman driver did not probed yet.
137 * bman_portals_probed - Check if all cpu bound bman portals are probed
139 * Returns 1 if all the required cpu bound bman portals successfully probed,
|
| /linux-6.8/arch/loongarch/kernel/ ! |
| D | cpu-probe.c | 236 pr_info("32-bit Loongson Processor probed (LA132 Core)\n"); in cpu_probe_loongson()
242 pr_info("64-bit Loongson Processor probed (LA264 Core)\n"); in cpu_probe_loongson()
248 pr_info("64-bit Loongson Processor probed (LA364 Core)\n"); in cpu_probe_loongson()
254 pr_info("64-bit Loongson Processor probed (LA464 Core)\n"); in cpu_probe_loongson()
260 pr_info("64-bit Loongson Processor probed (LA664 Core)\n"); in cpu_probe_loongson()
266 pr_info("64-bit Loongson Processor probed (Unknown Core)\n"); in cpu_probe_loongson()
|
| /linux-6.8/tools/perf/util/ ! |
| D | cloexec.c | 83 static bool probed; in perf_event_open_cloexec_flag() local
85 if (!probed) { in perf_event_open_cloexec_flag()
88 probed = true; in perf_event_open_cloexec_flag()
|
| /linux-6.8/drivers/base/test/ ! |
| D | platform-device-test.c | 52 * Tests that a platform bus, non-probed device will run its
80 * Tests that a platform bus, non-probed device will run its
128 * Tests that a platform bus, probed device will run its device-managed
166 * Tests that a platform bus, probed device will run its device-managed
|
| D | root-device-test.c | 41 * Tests that a bus-less, non-probed device will run its device-managed
72 * Tests that a bus-less, non-probed device will run its device-managed
|
| /linux-6.8/Documentation/trace/ ! |
| D | kprobes.rst | 64 When a kprobe is registered, Kprobes makes a copy of the probed
65 instruction and replaces the first byte(s) of the probed instruction
74 Next, Kprobes single-steps its copy of the probed instruction.
111 the entry to the function. When the probed function is called and this
117 When the probed function executes its return instruction, control
123 While the probed function is executing, its return address is
127 function can be probed simultaneously. register_kretprobe()
139 time the probed function is entered but there is no kretprobe_instance
163 In case probed function is entered but there is no kretprobe_instance
228 - Other instructions in the optimized region are probed.
[all …]
|
| /linux-6.8/include/linux/mfd/pcf50633/ ! |
| D | backlight.h | 13 * Brightness to be used after the driver has been probed.
18 * Brightness limit to be used after the driver has been probed. This is useful
|
| /linux-6.8/drivers/clk/keystone/ ! |
| D | Kconfig | 25 firmware. By default, only the used clocks are probed from DT.
27 increase the boot time of the device. If you want the clocks probed
|
| /linux-6.8/drivers/clk/ti/ ! |
| D | clk-dra7-atl.c | 44 bool probed; /* the driver for the IP has been loaded */ member
76 if (!cdesc->probed) in atl_clk_enable()
98 if (!cdesc->probed) in atl_clk_disable()
272 cdesc->probed = true; in of_dra7_atl_clk_probe()
|
| /linux-6.8/Documentation/driver-api/ ! |
| D | device_link.rst | 30 presence on the supplier. The consumer devices are not probed before the
62 driver core known about the device link earlier, it wouldn't have probed the
114 consumer will never be probed.
250 add a device flag causing the parent driver to be probed before the
271 and consumer. If the link is created before any devices are probed, it
279 * Before a consumer device is probed, presence of supplier drivers is
|
| /linux-6.8/arch/x86/boot/ ! |
| D | video-mode.c | 34 static u8 probed[2]; in probe_cards() local
36 if (probed[unsafe]) in probe_cards()
39 probed[unsafe] = 1; in probe_cards()
|
| /linux-6.8/drivers/clocksource/ ! |
| D | renesas-ostm.c | 21 * The first OSTM channel probed will be set up as a free running
25 * The second (or more) channel probed will be set up as an interrupt
195 * First probed device will be used as system clocksource. Any in ostm_init()
|
| /linux-6.8/drivers/misc/eeprom/ ! |
| D | digsy_mtc_eeprom.c | 8 * FIXME: this driver is used on a device-tree probed platform: it
9 * should be defined as a bit-banged SPI device and probed from the device
|
| /linux-6.8/drivers/gpu/drm/vc4/ ! |
| D | vc4_perfmon.c | 153 DRM_DEBUG("Creating perfmon no VC4 V3D probed\n"); in vc4_perfmon_create_ioctl()
207 DRM_DEBUG("Destroying perfmon no VC4 V3D probed\n"); in vc4_perfmon_destroy_ioctl()
235 DRM_DEBUG("Getting perfmon no VC4 V3D probed\n"); in vc4_perfmon_get_values_ioctl()
|
| /linux-6.8/drivers/soundwire/ ! |
| D | bus_type.c | 122 /* device is probed so let's read the properties now */ in sdw_drv_probe()
146 slave->probed = true; in sdw_drv_probe()
174 slave->probed = false; in sdw_drv_remove()
|
| /linux-6.8/samples/kprobes/ ! |
| D | kretprobe_example.c | 6 * report the return value and total time taken for probed function
18 * whenever the probed function returns. (Some messages may be suppressed
|
| /linux-6.8/drivers/mfd/ ! |
| D | 88pm80x.c | 101 * workaround: set g_pm80x_chip to the first probed chip. if the in pm80x_init()
102 * second chip is probed, just point to the companion to each in pm80x_init()
|
| /linux-6.8/tools/testing/selftests/net/ ! |
| D | rtnetlink.sh | 566 probed=false
586 probed=true
620 $probed && rmmod netdevsim
740 probed=false
753 probed=true
833 $probed && rmmod netdevsim
1111 probed=false
1119 probed=true
1140 $probed && rmmod netdevsim
|
| /linux-6.8/samples/fprobe/ ! |
| D | fprobe_example.c | 28 MODULE_PARM_DESC(symbol, "Probed symbol(s), given by comma separated symbols or a wildcard pattern.…
32 MODULE_PARM_DESC(nosymbol, "Not-probed symbols, given by a wildcard pattern.");
|
| /linux-6.8/Documentation/hwmon/ ! |
| D | occ.rst | 19 The P8 version of this driver is a client driver of I2C. It may be probed
24 It will be probed automatically by the FSI-based OCC driver.
|
| /linux-6.8/kernel/trace/ ! |
| D | fprobe.c | 228 * @filter: A wildcard pattern of probed symbols.
229 * @notfilter: A wildcard pattern of NOT probed symbols.
232 * If @notfilter is not NULL, the symbols matched the @notfilter are not probed.
|
| D | trace_kprobe_selftest.h | 5 * can be probed by the selftests.
|
| D | trace_kprobe_selftest.c | 8 * can be probed by the selftests.
|