Searched full:operates (Results 1 – 25 of 265) sorted by relevance
1234567891011
| /linux-5.10/Documentation/userspace-api/media/v4l/ |
| D | libv4l-introduction.rst | 121 operates like the :c:func:`open()` function.
125 operates like the :c:func:`close()` function.
129 operates like the libc ``dup()`` function, duplicating a file handler.
133 operates like the :c:func:`ioctl()` function.
137 operates like the :c:func:`read()` function.
141 operates like the :c:func:`munmap()` function.
145 operates like the :c:func:`munmap()` function.
|
| D | pixfmt-meta-vsp1-hgo.rst | 19 or HSV data. It operates on a possibly cropped and subsampled input image and
28 - In *64 bins normal mode*, the HGO operates on the three channels independently
31 - In *64 bins maximum mode*, the HGO operates on the maximum of the (R, G, B)
34 - In *256 bins normal mode*, the HGO operates on the Y channel to compute a
36 - In *256 bins maximum mode*, the HGO operates on the maximum of the (R, G, B)
|
| D | pixfmt-meta-vsp1-hgt.rst | 18 The VSP1 HGT is a histogram computation engine that operates on HSV
19 data. It operates on a possibly cropped and subsampled input image and
|
| /linux-5.10/drivers/memory/ |
| D | ti-emif-sram-pm.S | 47 * transition. Operates on the VIRTUAL address of the EMIF.
141 * Operates on the PHYSICAL address of the EMIF.
292 * mode during a sleep transition. Operates on the VIRTUAL address
314 * after a sleep transition. Operates on the PHYSICAL address of
350 * Operates on the VIRTUAL address of the EMIF.
|
| /linux-5.10/Documentation/devicetree/bindings/i2c/ |
| D | i2c-exynos5.txt | 30 -> If not specified, the bus operates in fast-speed mode at
32 -> If specified, the bus operates in high-speed mode only if the
|
| /linux-5.10/Documentation/ABI/testing/ |
| D | sysfs-class-backlight-adp5520 | 4 The backlight brightness control operates at three different levels for the
6 (level 3). By default the brightness operates at the daylight brightness level.
|
| D | sysfs-class-backlight-adp8860 | 4 The backlight brightness control operates at three different levels for the
6 dark (level 3). By default the brightness operates at the daylight brightness
|
| /linux-5.10/Documentation/devicetree/bindings/net/ |
| D | adi,adin.yaml | 21 RGMII RX Clock Delay used only when PHY operates in RGMII mode with
28 RGMII TX Clock Delay used only when PHY operates in RGMII mode with
|
| /linux-5.10/Documentation/devicetree/bindings/serial/ |
| D | serial.yaml | 105 The maximum baud rate the device operates at.
114 The current baud rate the device operates at.
|
| /linux-5.10/drivers/rapidio/switches/ |
| D | idtcps.c | 94 * Switch domain configuration operates only at global level in idtcps_set_domain()
108 * Switch domain configuration operates only at global level in idtcps_get_domain()
|
| /linux-5.10/drivers/staging/vc04_services/bcm2835-camera/ |
| D | Kconfig | 12 Broadcom BCM2835 SoC. This operates over the VCHIQ interface
|
| /linux-5.10/drivers/staging/media/atomisp/pci/hive_isp_css_include/host/ |
| D | irq_public.h | 104 \Note: This function operates as strtok(), based on the return
160 \Note: This function operates as strtok(), based on the return
|
| /linux-5.10/drivers/net/ethernet/amazon/ena/ |
| D | ena_common_defs.h | 11 /* ENA operates with 48-bit memory addresses. ena_mem_addr_t */
|
| /linux-5.10/Documentation/networking/ |
| D | batman-adv.rst | 9 using UDP packets and sets routing tables, batman-advanced operates on ISO/OSI
143 As batman advanced operates on layer 2, all hosts participating in the virtual
|
| /linux-5.10/fs/ecryptfs/ |
| D | Kconfig | 9 Encrypted filesystem that operates on the VFS layer. See
|
| /linux-5.10/arch/alpha/include/asm/ |
| D | mc146818rtc.h | 12 #define RTC_ALWAYS_BCD 1 /* RTC operates in binary mode */
|
| /linux-5.10/arch/sparc/include/asm/ |
| D | mc146818rtc_32.h | 12 #define RTC_ALWAYS_BCD 1 /* RTC operates in binary mode */
|
| /linux-5.10/arch/powerpc/include/asm/ |
| D | mc146818rtc.h | 15 #define RTC_ALWAYS_BCD 1 /* RTC operates in binary mode */
|
| /linux-5.10/arch/arm/include/asm/ |
| D | mc146818rtc.h | 15 #define RTC_ALWAYS_BCD 1 /* RTC operates in binary mode */
|
| /linux-5.10/Documentation/devicetree/bindings/timer/ |
| D | brcm,kona-timer.txt | 12 - clock-frequency: frequency that the clock operates
|
| /linux-5.10/security/selinux/ss/ |
| D | context.c | 24 * already operates under the same assumption. in context_compute_hash()
|
| /linux-5.10/drivers/net/can/softing/ |
| D | Kconfig | 11 and PCMCIA cards. This driver operates on a platform device,
|
| /linux-5.10/include/linux/ |
| D | scatterlist.h | 427 * In each loop it operates on PAGE_SIZE unit.
442 * In each loop it operates on PAGE_SIZE unit.
457 * See also for_each_sg_page(). In each loop it operates on PAGE_SIZE unit.
470 * See also for_each_sg_dma_page(). In each loop it operates on PAGE_SIZE
|
| /linux-5.10/tools/include/uapi/linux/ |
| D | openat2.h | 9 * @mode are non-zero, then openat2(2) operates very similarly to openat(2).
|
| /linux-5.10/include/uapi/linux/ |
| D | openat2.h | 9 * @mode are non-zero, then openat2(2) operates very similarly to openat(2).
|
1234567891011