Searched full:ksps (Results 1 – 14 of 14) sorted by relevance
| /linux-6.8/Documentation/devicetree/bindings/iio/adc/ |
| D | microchip,mcp3564.yaml | 13 Bindings for the Microchip family of 153.6 ksps, Low-Noise 16/24-Bit
20 …APID/ProductDocuments/DataSheets/MCP3461-2-4-Two-Four-Eight-Channel-153.6-ksps-Low-Noise-16-Bit-De…
|
| /linux-6.8/drivers/hwmon/ |
| D | adcxx.c | 14 * * sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500 kSPS
|
| D | Kconfig | 1312 * sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500
1313 kSPS and 101 for 1 MSPS)
|
| /linux-6.8/drivers/mfd/ |
| D | ti_am335x_tscadc.c | 226 * am33xx ADCs expect to capture 200ksps. in ti_tscadc_probe()
227 * am47xx ADCs expect to capture 867ksps. in ti_tscadc_probe()
|
| /linux-6.8/drivers/iio/adc/ |
| D | ti-ads131e08.c | 133 unsigned int rate; /* data rate in kSPS */
624 * For 32 and 64 ksps data rates, number of data bits per channel in ads131e08_trigger_handler()
|
| D | xilinx-xadc-core.c | 118 * limits the maximum samplerate 150kSPS. At this rate the CPU is fairly busy,
993 /* Max. 150 kSPS */ in xadc_write_samplerate()
1004 * We want to round down, but only if we do not exceed the 150 kSPS in xadc_write_samplerate()
|
| D | ad7768-1.c | 463 /* Set the default sampling frequency to 32000 kSPS */ in ad7768_setup()
|
| D | max1027.c | 63 /* Device can achieve 300ksps so we assume a 3.33us conversion delay */
|
| D | mcp3564.c | 14 …APID/ProductDocuments/DataSheets/MCP3461-2-4-Two-Four-Eight-Channel-153.6-ksps-Low-Noise-16-Bit-De…
|
| /linux-6.8/drivers/media/pci/cx18/ |
| D | cx18-driver.c | 1175 /* MPEG Encoding, 224 kbps, MPEG Layer II, 48 ksps */ in cx18_init_on_first_open()
1202 /* MPEG Encoding, 224 kbps, MPEG Layer II, 48 ksps */ in cx18_init_on_first_open()
|
| /linux-6.8/arch/arm64/boot/dts/freescale/ |
| D | imx8mp-tqma8mpql-mba8mpxl.dts | 300 /* 100 ksps * 18 */
|
| /linux-6.8/drivers/media/dvb-frontends/ |
| D | mb86a16.c | 1041 dprintk(verbose, MB86A16_INFO, 1, "freq=%d Mhz, symbrt=%d Ksps", state->frequency, state->srate); in mb86a16_set_fe()
|
| D | stv090x.c | 1602 if (STV090x_WRITE_DEMOD(state, SFRLOW1, 0x82) < 0) /* SR= 400 ksps Min */ in stv090x_get_agc2_min_level()
|
| /linux-6.8/drivers/media/i2c/cx25840/ |
| D | cx25840-core.c | 892 * 48 ksps, 16 bits/sample, x160 multiplier = 122.88 MHz in cx23885_initialize()
894 * 48 ksps, 16 bits/sample, x16 multiplier = 12.288 MHz in cx23885_initialize()
|