| /linux/Documentation/mhi/ ! |
| H A D | topology.rst | 26 * Initiates power on and shutdown sequence
27 * Initiates suspend and resume power management operations of the device.
58 * Initiates data transfer by calling mhi_queue_transfer.
|
| /linux/Documentation/w1/slaves/ ! |
| H A D | w1_ds2438.rst | 66 Opening and reading this file initiates the CONVERT_T (temperature conversion)
75 Opening and reading this file initiates the CONVERT_V (voltage conversion)
|
| H A D | w1_ds2423.rst | 20 read sequence of w1_slave file initiates the read of counters and ram
|
| /linux/drivers/char/xilinx_hwicap/ ! |
| H A D | buffer_icap.c | 156 * this register initiates the transfer. A value of 1 initiates a
157 * readback while writing a value of 0 initiates a configuration.
|
| /linux/Documentation/ABI/testing/ ! |
| H A D | sysfs-bus-iio-adc-ad-sigma-delta | 5 This attribute, if available, initiates the system calibration procedure. This is done on a
|
| H A D | sysfs-bus-fsi | 6 Initiates a FSI master scan for all connected slave devices
|
| H A D | sysfs-class-mic | 68 "reset" Initiates device reset.
69 "shutdown" Initiates card OS shutdown.
|
| /linux/Documentation/devicetree/bindings/fpga/ ! |
| H A D | lattice,sysconfig.yaml | 31 Initiates configuration sequence.
|
| /linux/include/soc/tegra/ ! |
| H A D | ivc.h | 85 * tegra_ivc_reset - initiates a reset of the shared memory state
|
| /linux/Documentation/devicetree/bindings/iio/adc/ ! |
| H A D | adi,ad4030.yaml | 57 The Convert Input (CNV). It initiates the sampling conversions.
|
| H A D | adi,ad7944.yaml | 102 The Convert Input (CNV). This input has multiple functions. It initiates
|
| /linux/Documentation/gpu/amdgpu/ ! |
| H A D | process-isolation.rst | 59 This command initiates the cleaner shader, which will run and complete before any new tasks are sch…
|
| /linux/include/linux/ ! |
| H A D | wm97xx.h | 77 #define WM9712_MASK_SYNC 0x00c0 /* rising/falling edge on mask initiates sample */
95 #define WM9705_MASK_SYNC 0x0030 /* rising/falling edge on mask initiates sample */
|
| /linux/drivers/firmware/arm_scmi/ ! |
| H A D | scmi_power_control.c | 154 * Initiates the required SystemPower transition without involving userspace:
206 * Initiates the required SystemPower transition, requesting userspace
|
| /linux/drivers/gpu/drm/xe/ ! |
| H A D | xe_sriov_vf.c | 27 * VMM initiates all required operations through VFIO module, which then
29 * calls, leaving out the module which initiates these steps (VFIO).
|
| /linux/Documentation/devicetree/bindings/dma/stm32/ ! |
| H A D | st,stm32-dma.yaml | 41 0x1: Direct mode: each DMA request immediately initiates a transfer
|
| /linux/Documentation/filesystems/iomap/ ! |
| H A D | operations.rst | 178 The ``iomap_readahead`` function initiates readahead to the pagecache.
483 A direct I/O read initiates a read I/O from the storage device to the
498 A direct I/O write initiates a write I/O to the storage device from the
616 A fsdax write initiates a memcpy to the storage device from the caller's
|
| /linux/tools/perf/pmu-events/arch/x86/goldmontplus/ ! |
| H A D | frontend.json | 70 …truction encounters a fault, trap, or microcode assist of any sort that initiates a flow of uops. …
|
| /linux/tools/perf/pmu-events/arch/x86/goldmont/ ! |
| H A D | frontend.json | 70 …truction encounters a fault, trap, or microcode assist of any sort that initiates a flow of uops. …
|
| /linux/Documentation/hwmon/ ! |
| H A D | ntc_thermistor.rst | 108 (reading this file initiates the reading procedure.)
|
| /linux/Documentation/driver-api/ ! |
| H A D | slimbus.rst | 109 Clock-pause is exited by waking up framer device (if controller driver initiates
|
| /linux/include/rdma/ ! |
| H A D | ib_sa.h | 429 * ib_sa_join_multicast - Initiates a join request to the specified multicast
442 * This call initiates a multicast join request with the SA for the specified
|
| /linux/Documentation/driver-api/soundwire/ ! |
| H A D | stream.rst | 359 (4) Once all the values are programmed, Bus initiates switch to alternate
393 (3) Once all the values are programmed, Bus initiates switch to alternate
421 (3) Once all the values are programmed, Bus initiates switch to alternate
|
| /linux/Documentation/networking/ ! |
| H A D | mptcp.rst | 59 address announcements. Typically, it is the client side that initiates subflows,
|
| /linux/arch/mips/kernel/ ! |
| H A D | sync-r4k.c | 106 * The freshly booted CPU initiates this via an async SMP function call.
|