| /linux-5.10/sound/soc/intel/catpt/ |
| D | ipc.c | 150 struct catpt_notify_glitch glitch; in catpt_dsp_notify_stream() local
168 memcpy_fromio(&glitch, catpt_inbox_addr(cdev), sizeof(glitch)); in catpt_dsp_notify_stream()
169 trace_catpt_ipc_payload((u8 *)&glitch, sizeof(glitch)); in catpt_dsp_notify_stream()
171 dev_warn(cdev->dev, "glitch %d at pos: 0x%08llx, wp: 0x%08x\n", in catpt_dsp_notify_stream()
172 glitch.type, glitch.presentation_pos, in catpt_dsp_notify_stream()
173 glitch.write_pos); in catpt_dsp_notify_stream()
|
| /linux-5.10/drivers/pinctrl/ |
| D | pinctrl-at91.h | 18 #define PIO_IFER 0x20 /* Glitch Input Filter Enable */
19 #define PIO_IFDR 0x24 /* Glitch Input Filter Disable */
20 #define PIO_IFSR 0x28 /* Glitch Input Filter Status */
|
| /linux-5.10/drivers/clk/qcom/ |
| D | clk-rcg.h | 98 * struct clk_dyn_rcg - root clock generator with glitch free mux
100 * @mux_sel_bit: bit to switch glitch free mux
103 * @bank_reg: register to XOR @mux_sel_bit into to switch glitch free mux
|
| /linux-5.10/arch/arm64/boot/dts/amlogic/ |
| D | meson-gxbb.dtsi | 743 * VPU_0 and VPU_1 muxed to a single clock by a glitch
745 * Same for VAPB but with a final gate after the glitch free mux.
749 <&clkc CLKID_VPU>, /* Glitch free mux */
752 <&clkc CLKID_VAPB_SEL>; /* Glitch free mux */
|
| D | meson-gxl.dtsi | 812 * VPU_0 and VPU_1 muxed to a single clock by a glitch
814 * Same for VAPB but with a final gate after the glitch free mux.
818 <&clkc CLKID_VPU>, /* Glitch free mux */
821 <&clkc CLKID_VAPB_SEL>; /* Glitch free mux */
|
| /linux-5.10/arch/arm/mach-s3c/ |
| D | pm-gpio.c | 108 * { OUT => SFN } Change CON first, so new data will not glitch
109 * { OUT => IN } Change CON first, so new data will not glitch
111 * { SFN => OUT } Change DAT first, so new data will not glitch [1]
|
| D | pm.h | 92 * that we do not glitch the state of the pins from that the bootloader's
|
| /linux-5.10/drivers/rtc/ |
| D | rtc-mxc_v2.c | 16 #define SRTC_LPPDR_INIT 0x41736166 /* init for glitch detect */
34 #define SRTC_LPPDR 0x18 /* LP Power Supply Glitch Detector Reg */
314 /* initialize glitch detect */ in mxc_rtc_probe()
|
| D | rtc-dm355evm.c | 22 * The only real glitch is the inability to read or write all four
|
| D | rtc-max6916.c | 128 /*Enable oscillator,disable oscillator stop flag, glitch filter*/ in max6916_probe()
|
| /linux-5.10/Documentation/devicetree/bindings/leds/ |
| D | common.yaml | 65 default-state property is set the to same value, then no glitch should be
68 glitch.
|
| /linux-5.10/Documentation/devicetree/bindings/phy/ |
| D | qcom,usb-hsic-phy.txt | 38 Definition: List of pinctrl settings to apply to keep HSIC pins in a glitch
|
| /linux-5.10/include/linux/pinctrl/ |
| D | pinctrl-state.h | 19 * glitch the pins. In those cases you can add an "init" pinctrl
|
| /linux-5.10/drivers/pinctrl/nomadik/ |
| D | pinctrl-nomadik.c | 379 bool glitch) in __nmk_gpio_set_mode_safe() argument
384 if (glitch && nmk_chip->set_ioforce) { in __nmk_gpio_set_mode_safe()
396 if (glitch && nmk_chip->set_ioforce) { in __nmk_gpio_set_mode_safe()
1523 bool glitch; in nmk_pmx_set() local
1555 glitch = ((g->altsetting & NMK_GPIO_ALT_C) == NMK_GPIO_ALT_C); in nmk_pmx_set()
1557 if (glitch) { in nmk_pmx_set()
1597 (g->altsetting & NMK_GPIO_ALT_C), glitch); in nmk_pmx_set()
1617 if (glitch) { in nmk_pmx_set()
1649 /* There is no glitch when converting any pin to GPIO */ in nmk_gpio_request_enable()
1763 /* No glitch when going to GPIO mode */ in nmk_pin_config_set()
|
| /linux-5.10/Documentation/ABI/testing/ |
| D | sysfs-class-mei | 90 The ME FW writes Glitch Detection HW (TRC)
|
| /linux-5.10/include/dt-bindings/pinctrl/ |
| D | dra.h | 30 /* Certain pins need virtual mode, but note: they may glitch */
|
| /linux-5.10/Documentation/driver-api/gpio/ |
| D | intro.rst | 56 input de-glitch/debounce logic, sometimes with software controls.
|
| D | legacy.rst | 40 input de-glitch/debounce logic, sometimes with software controls.
286 setup of an output GPIO's value. This allows a glitch-free migration from a
676 initializing the value as low. To ensure glitch free
|
| /linux-5.10/Documentation/admin-guide/gpio/ |
| D | sysfs.rst | 77 initializing the value as low. To ensure glitch free
|
| /linux-5.10/drivers/gpu/drm/meson/ |
| D | meson_dw_hdmi.h | 54 * Bit 15:12 RW hpd_glitch_width: filter out glitch <= N. Default 0.
|
| /linux-5.10/drivers/pwm/ |
| D | pwm-iqs620a.c | 11 * and may result in a glitch during the period in which the change is made.
|
| /linux-5.10/drivers/i2c/busses/ |
| D | i2c-stu300.c | 195 /* Twice paranoia (possible HW glitch) */ in stu300_irq_enable()
205 /* Twice paranoia (possible HW glitch) */ in stu300_irq_disable()
569 * Enable block, do it TWICE (hardware glitch) in stu300_init_hw()
|
| /linux-5.10/drivers/staging/olpc_dcon/ |
| D | olpc_dcon.c | 296 pr_err("Timeout entering CPU mode; expect a screen glitch.\n"); in dcon_source_switch()
335 pr_err("Timeout entering DCON mode; expect a screen glitch.\n"); in dcon_source_switch()
|
| /linux-5.10/drivers/media/cec/platform/meson/ |
| D | ao-cec-g12a.c | 46 * [14:12] Filter_del. For glitch-filtering CEC line, ignore signal
49 * glitch-filtering CEC line signal.
|
| /linux-5.10/arch/arm/mach-imx/ |
| D | mach-imx6q.c | 121 /* Ar803x phy SmartEEE feature cause link status generates glitch, in ar8035_phy_fixup()
|