| /linux-6.8/Documentation/devicetree/bindings/iio/adc/ |
| D | xilinx-xadc.txt | 82 * xlnx,bipolar: If set the channel is used in bipolar
121 xlnx,bipolar;
138 xlnx,bipolar;
|
| D | adc.yaml | 28 bipolar:
30 description: If provided, the channel is to be used in bipolar mode.
|
| D | xlnx,zynqmp-ams.yaml | 175 xlnx,bipolar:
179 If the set channel is used in bipolar mode.
225 xlnx,bipolar;
232 xlnx,bipolar;
|
| D | adi,ad7124.yaml | 91 bipolar: true
140 bipolar;
|
| D | adi,max11410.yaml | 107 bipolar: true
165 bipolar;
|
| D | adi,ad4130.yaml | 79 adi,bipolar:
80 description: Specify if the device should be used in bipolar mode.
|
| D | adi,ad7192.yaml | 83 bipolar:
|
| /linux-6.8/drivers/comedi/drivers/ |
| D | dt2815.c | 22 * [2] - Voltage unipolar/bipolar configuration
24 * 1 == bipolar 5V (-5V -- +5V)
118 * options[2] Voltage unipolar/bipolar configuration
120 * 1 == bipolar 5V (-5V -- +5V)
|
| D | ni_daq_700.c | 31 * 0 for -10 to 10V bipolar
32 * 1 for -5 to 5V bipolar
33 * 2 for -2.5 to 2.5V bipolar
175 /* Bipolar Offset Binary: 0 to 4095 for -10 to +10 */ in daq700_ai_rinsn()
|
| D | das1800.c | 66 * Unipolar and bipolar ranges cannot be mixed in the channel/gain list.
145 BIP_RANGE(5), /* bipolar gain = 1 */
146 BIP_RANGE(1), /* bipolar gain = 10 */
147 BIP_RANGE(0.1), /* bipolar gain = 50 */
148 BIP_RANGE(0.02), /* bipolar gain = 250 */
158 BIP_RANGE(10), /* bipolar gain = 1 */
159 BIP_RANGE(5), /* bipolar gain = 2 */
160 BIP_RANGE(2.5), /* bipolar gain = 4 */
161 BIP_RANGE(1.25), /* bipolar gain = 8 */
624 "unipolar and bipolar ranges cannot be mixed in the chanlist\n"); in das1800_ai_check_chanlist()
|
| D | cb_pcimdda.c | 25 * 5 Volt unipolar, 5V bipolar, 10 Volt unipolar or 10V bipolar.
|
| D | adq12b.c | 32 * [1] - Analog Input unipolar/bipolar selection
34 * bipolar 0 2-3 (factory default)
|
| D | amplc_pci224.c | 133 /* (r/w) Polarity (PCI224 only, PCI234 always bipolar!). */
276 RANGE_ext(-1, 1), /* bipolar [-Vext,+Vext] */
315 RANGE_ext(-2, 2), /* bipolar [-2*Vext,+2*Vext] */
317 RANGE_ext(-1, 1), /* bipolar [-Vext,+Vext] */
402 * - bipolar: 16-bit 2's complement in pci224_ao_set_data()
926 /* Channels will be all bipolar or all unipolar. */ in pci224_ao_munge()
932 /* Bipolar */ in pci224_ao_munge()
|
| D | amplc_pci230.c | 107 * bipolar (ranges 0 to 3) or all unipolar (ranges 4 to 6). The channel
231 #define PCI230_DAC_OR_BIP PCI230_DAC_OR(1) /* Output bipolar */
310 #define PCI230_ADC_IR_BIP PCI230_ADC_IR(1) /* Input bipolar */
492 unsigned int ai_bipolar:1; /* Flag AI range is bipolar */
493 unsigned int ao_bipolar:1; /* Flag AO range is bipolar */
543 * If a bipolar range was specified, mangle it in pci230_ai_read()
564 * If a bipolar range was specified, mangle it in pci230_ao_mangle_datum()
833 * 1 => bipolar +/-10V range scale in pci230_ao_insn_write()
1316 * 1 => bipolar +/-10V range scale in pci230_ao_cmd()
1419 bool bipolar = comedi_range_is_bipolar(s, range); in pci230_ai_check_chanlist() local
[all …]
|
| D | icp_multi.c | 44 #define ICP_MULTI_ADC_CSR_BI BIT(4) /* Bipolar input range */
53 #define ICP_MULTI_DAC_CSR_BI BIT(4) /* Bipolar output range */
|
| D | addi_apci_3501.c | 119 * 14-bit bipolar: 0-10V in apci3501_ao_insn_write()
283 /* Default all analog outputs to 0V (bipolar) */ in apci3501_reset()
|
| D | rti802.c | 21 * [3,5,7,9,11,13,15,17] - dac#[0-7] 0=bipolar, 1=unipolar
|
| /linux-6.8/drivers/iio/adc/ |
| D | ad7124.c | 150 bool bipolar; member
398 val = AD7124_CONFIG_BIPOLAR(cfg->bipolar) | AD7124_CONFIG_REF_SEL(cfg->refsel) | in ad7124_write_config()
596 if (st->channels[chan->address].cfg.bipolar) in ad7124_read_raw()
605 if (st->channels[chan->address].cfg.bipolar) in ad7124_read_raw()
654 if (st->channels[chan->address].cfg.bipolar) in ad7124_write_raw()
864 cfg->bipolar = of_property_read_bool(child, "bipolar"); in ad7124_of_parse_channel_config()
|
| D | max11410.c | 128 bool bipolar; member
371 FIELD_PREP(MAX11410_CTRL_UNIPOLAR_BIT, cfg.bipolar ? 0 : 1); in max11410_configure_channel()
447 if (cfg.bipolar) in max11410_get_scale()
467 if (cfg.bipolar) in max11410_read_raw()
782 cfg->bipolar = fwnode_property_read_bool(child, "bipolar"); in max11410_parse_channels()
|
| D | ad7192.c | 101 #define AD7192_CONF_UNIPOLAR BIT(3) /* Unipolar/Bipolar Enable */
392 bool buf_en, bipolar, burnout_curr_en; in ad7192_setup() local
433 bipolar = of_property_read_bool(np, "bipolar"); in ad7192_setup()
434 if (!bipolar) in ad7192_setup()
|
| /linux-6.8/include/linux/comedi/ |
| D | comedidev.h | 640 * comedi_range_is_bipolar() - Test if subdevice range is bipolar
644 * Tests whether a range is bipolar by checking whether its minimum value
651 * %true if the range is bipolar.
673 * %false if the range is bipolar.
703 * comedi_chan_range_is_bipolar() - Test if channel-specific range is bipolar
708 * Tests whether a range is bipolar by checking whether its minimum value
715 * %true if the range is bipolar.
739 * %false if the range is bipolar.
761 * %true if the range is bipolar.
|
| /linux-6.8/include/linux/platform_data/ |
| D | ad7791.h | 10 * bipolar mode.
|
| D | ad7793.h | 92 * bipolar mode.
|
| /linux-6.8/Documentation/devicetree/bindings/iio/addac/ |
| D | adi,ad74115.yaml | 178 adi,dac-bipolar:
368 adi,dac-bipolar;
|
| /linux-6.8/Documentation/hwmon/ |
| D | max197.rst | 50 3 BIP Unipolar or Bipolar conversion mode
|