Searched full:can2 (Results 1 – 25 of 116) sorted by relevance
12345
14 * pins SD3_DAT0 and SD3_DAT1 are muxed as can2 Tx and Rx. The signals for can219 &can2 {72 * Due to the use of can2 the signals for can2 Tx and Rx are routed to108 * Due to the use of can2 the micro SD card on module have to be110 * can2 Tx and Rx.
6 * DHCM-iMX6ULL-C080-R051-F0409-SPI-E2-CAN2-SD-RTC-ADC-I-01D223 * The signals for CAN2 TX and RX are routed to the DHCOM UART1 RTS/CTS pins.27 &can2 {
18 * Note: can2 and fec2 are enabled on mba6ulx level (for i.MX6ULG2 usage)21 &can2 {
15 can1 = &can2;143 reg_can2_stby: regulator-can2-stby {147 regulator-name = "can2-3v3";201 &can2 {
62 /* CAN2 is multiplexed with UART2 RTS/CTS */63 &can2 {201 /* UART2 RTS/CTS muxed with CAN2 */
82 reg_can2_supply: regulator-can2-supply {98 &can2 {
13 /delete-node/ &can2;
21 &can2 {
23 &can2 {
6 * DHCM-iMX6S-C0800-R102-F0409-E-CAN2-RTC-I-01D2
27 &can2 {
89 * pins SD3_DAT0 and SD3_DAT1 are muxed as can2 Tx and Rx. The signals for can290 * Tx and Rx are routed to the DHCOM UART1 rts/cts pins. So to enable can2 on94 &can2 {
61 &can2 {
6 * DHCM-iMX6ULL-C080-R051-F0409-SPI-E2-CAN2-SD-RTC-ADC-I-01D2
18 mode, which can interoperate with CAN2.0 nodes but does not support
74 reg_can2_supply: regulator-can2-supply {116 /* Apalis CAN2 */
32 reg_can2_stby: regulator-can2-stby {39 regulator-name = "can2-stby";
43 /* Apalis CAN2 */
6 * DHCM-STM32MP157C-C065-R102-F0819-SPI-E2-CAN2-SDR104-RTC-WBT-T-DSI-I-01D2
6 * DHCM-STM32MP157C-C065-R102-F0819-SPI-E-CAN2-SD-RTC-T-DSI-I-01D2
6 * DHCM-STM32MP153C-C065-R102-F0819-SPI-E2-CAN2-RTC-I-01D2
77 /* CS5a: CAN2 (0xb4000000 - 0xb5ffffff) */ in setup_chip_select()371 irq_set_irq_type(evt2irq(0x620), IRQ_TYPE_LEVEL_LOW); /* IRQ1 CAN2 */ in init_mpr2_IRQ()378 intc_set_priority(evt2irq(0x620), 13); /* IRQ0 CAN2 */ in init_mpr2_IRQ()
69 SRAM memory shared by the two bxCAN cells (CAN1 primary and CAN2