1 /* SPDX-License-Identifier: ISC */
2 /*
3  * Copyright (c) 2005-2011 Atheros Communications Inc.
4  * Copyright (c) 2011-2017 Qualcomm Atheros, Inc.
5  * Copyright (c) 2018-2019, The Linux Foundation. All rights reserved.
6  * Copyright (c) 2021-2024 Qualcomm Innovation Center, Inc. All rights reserved.
7  */
8 
9 #ifndef _WMI_H_
10 #define _WMI_H_
11 
12 #include <linux/types.h>
13 #include <linux/ieee80211.h>
14 
15 /*
16  * This file specifies the WMI interface for the Unified Software
17  * Architecture.
18  *
19  * It includes definitions of all the commands and events. Commands are
20  * messages from the host to the target. Events and Replies are messages
21  * from the target to the host.
22  *
23  * Ownership of correctness in regards to WMI commands belongs to the host
24  * driver and the target is not required to validate parameters for value,
25  * proper range, or any other checking.
26  *
27  * Guidelines for extending this interface are below.
28  *
29  * 1. Add new WMI commands ONLY within the specified range - 0x9000 - 0x9fff
30  *
31  * 2. Use ONLY u32 type for defining member variables within WMI
32  *    command/event structures. Do not use u8, u16, bool or
33  *    enum types within these structures.
34  *
35  * 3. DO NOT define bit fields within structures. Implement bit fields
36  *    using masks if necessary. Do not use the programming language's bit
37  *    field definition.
38  *
39  * 4. Define macros for encode/decode of u8, u16 fields within
40  *    the u32 variables. Use these macros for set/get of these fields.
41  *    Try to use this to optimize the structure without bloating it with
42  *    u32 variables for every lower sized field.
43  *
44  * 5. Do not use PACK/UNPACK attributes for the structures as each member
45  *    variable is already 4-byte aligned by virtue of being a u32
46  *    type.
47  *
48  * 6. Comment each parameter part of the WMI command/event structure by
49  *    using the 2 stars at the beginning of C comment instead of one star to
50  *    enable HTML document generation using Doxygen.
51  *
52  */
53 
54 /* Control Path */
55 struct wmi_cmd_hdr {
56 	__le32 cmd_id;
57 } __packed;
58 
59 #define WMI_CMD_HDR_CMD_ID_MASK   0x00FFFFFF
60 #define WMI_CMD_HDR_CMD_ID_LSB    0
61 #define WMI_CMD_HDR_PLT_PRIV_MASK 0xFF000000
62 #define WMI_CMD_HDR_PLT_PRIV_LSB  24
63 
64 #define HTC_PROTOCOL_VERSION    0x0002
65 #define WMI_PROTOCOL_VERSION    0x0002
66 
67 /*
68  * There is no signed version of __le32, so for a temporary solution come
69  * up with our own version. The idea is from fs/ntfs/endian.h.
70  *
71  * Use a_ prefix so that it doesn't conflict if we get proper support to
72  * linux/types.h.
73  */
74 typedef __s32 __bitwise a_sle32;
75 
a_cpu_to_sle32(s32 val)76 static inline a_sle32 a_cpu_to_sle32(s32 val)
77 {
78 	return (__force a_sle32)cpu_to_le32(val);
79 }
80 
a_sle32_to_cpu(a_sle32 val)81 static inline s32 a_sle32_to_cpu(a_sle32 val)
82 {
83 	return le32_to_cpu((__force __le32)val);
84 }
85 
86 enum wmi_service {
87 	WMI_SERVICE_BEACON_OFFLOAD = 0,
88 	WMI_SERVICE_SCAN_OFFLOAD,
89 	WMI_SERVICE_ROAM_OFFLOAD,
90 	WMI_SERVICE_BCN_MISS_OFFLOAD,
91 	WMI_SERVICE_STA_PWRSAVE,
92 	WMI_SERVICE_STA_ADVANCED_PWRSAVE,
93 	WMI_SERVICE_AP_UAPSD,
94 	WMI_SERVICE_AP_DFS,
95 	WMI_SERVICE_11AC,
96 	WMI_SERVICE_BLOCKACK,
97 	WMI_SERVICE_PHYERR,
98 	WMI_SERVICE_BCN_FILTER,
99 	WMI_SERVICE_RTT,
100 	WMI_SERVICE_RATECTRL,
101 	WMI_SERVICE_WOW,
102 	WMI_SERVICE_RATECTRL_CACHE,
103 	WMI_SERVICE_IRAM_TIDS,
104 	WMI_SERVICE_ARPNS_OFFLOAD,
105 	WMI_SERVICE_NLO,
106 	WMI_SERVICE_GTK_OFFLOAD,
107 	WMI_SERVICE_SCAN_SCH,
108 	WMI_SERVICE_CSA_OFFLOAD,
109 	WMI_SERVICE_CHATTER,
110 	WMI_SERVICE_COEX_FREQAVOID,
111 	WMI_SERVICE_PACKET_POWER_SAVE,
112 	WMI_SERVICE_FORCE_FW_HANG,
113 	WMI_SERVICE_GPIO,
114 	WMI_SERVICE_STA_DTIM_PS_MODULATED_DTIM,
115 	WMI_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG,
116 	WMI_SERVICE_STA_UAPSD_VAR_AUTO_TRIG,
117 	WMI_SERVICE_STA_KEEP_ALIVE,
118 	WMI_SERVICE_TX_ENCAP,
119 	WMI_SERVICE_BURST,
120 	WMI_SERVICE_SMART_ANTENNA_SW_SUPPORT,
121 	WMI_SERVICE_SMART_ANTENNA_HW_SUPPORT,
122 	WMI_SERVICE_ROAM_SCAN_OFFLOAD,
123 	WMI_SERVICE_AP_PS_DETECT_OUT_OF_SYNC,
124 	WMI_SERVICE_EARLY_RX,
125 	WMI_SERVICE_STA_SMPS,
126 	WMI_SERVICE_FWTEST,
127 	WMI_SERVICE_STA_WMMAC,
128 	WMI_SERVICE_TDLS,
129 	WMI_SERVICE_MCC_BCN_INTERVAL_CHANGE,
130 	WMI_SERVICE_ADAPTIVE_OCS,
131 	WMI_SERVICE_BA_SSN_SUPPORT,
132 	WMI_SERVICE_FILTER_IPSEC_NATKEEPALIVE,
133 	WMI_SERVICE_WLAN_HB,
134 	WMI_SERVICE_LTE_ANT_SHARE_SUPPORT,
135 	WMI_SERVICE_BATCH_SCAN,
136 	WMI_SERVICE_QPOWER,
137 	WMI_SERVICE_PLMREQ,
138 	WMI_SERVICE_THERMAL_MGMT,
139 	WMI_SERVICE_RMC,
140 	WMI_SERVICE_MHF_OFFLOAD,
141 	WMI_SERVICE_COEX_SAR,
142 	WMI_SERVICE_BCN_TXRATE_OVERRIDE,
143 	WMI_SERVICE_NAN,
144 	WMI_SERVICE_L1SS_STAT,
145 	WMI_SERVICE_ESTIMATE_LINKSPEED,
146 	WMI_SERVICE_OBSS_SCAN,
147 	WMI_SERVICE_TDLS_OFFCHAN,
148 	WMI_SERVICE_TDLS_UAPSD_BUFFER_STA,
149 	WMI_SERVICE_TDLS_UAPSD_SLEEP_STA,
150 	WMI_SERVICE_IBSS_PWRSAVE,
151 	WMI_SERVICE_LPASS,
152 	WMI_SERVICE_EXTSCAN,
153 	WMI_SERVICE_D0WOW,
154 	WMI_SERVICE_HSOFFLOAD,
155 	WMI_SERVICE_ROAM_HO_OFFLOAD,
156 	WMI_SERVICE_RX_FULL_REORDER,
157 	WMI_SERVICE_DHCP_OFFLOAD,
158 	WMI_SERVICE_STA_RX_IPA_OFFLOAD_SUPPORT,
159 	WMI_SERVICE_MDNS_OFFLOAD,
160 	WMI_SERVICE_SAP_AUTH_OFFLOAD,
161 	WMI_SERVICE_ATF,
162 	WMI_SERVICE_COEX_GPIO,
163 	WMI_SERVICE_ENHANCED_PROXY_STA,
164 	WMI_SERVICE_TT,
165 	WMI_SERVICE_PEER_CACHING,
166 	WMI_SERVICE_AUX_SPECTRAL_INTF,
167 	WMI_SERVICE_AUX_CHAN_LOAD_INTF,
168 	WMI_SERVICE_BSS_CHANNEL_INFO_64,
169 	WMI_SERVICE_EXT_RES_CFG_SUPPORT,
170 	WMI_SERVICE_MESH_11S,
171 	WMI_SERVICE_MESH_NON_11S,
172 	WMI_SERVICE_PEER_STATS,
173 	WMI_SERVICE_RESTRT_CHNL_SUPPORT,
174 	WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT,
175 	WMI_SERVICE_TX_MODE_PUSH_ONLY,
176 	WMI_SERVICE_TX_MODE_PUSH_PULL,
177 	WMI_SERVICE_TX_MODE_DYNAMIC,
178 	WMI_SERVICE_VDEV_RX_FILTER,
179 	WMI_SERVICE_BTCOEX,
180 	WMI_SERVICE_CHECK_CAL_VERSION,
181 	WMI_SERVICE_DBGLOG_WARN2,
182 	WMI_SERVICE_BTCOEX_DUTY_CYCLE,
183 	WMI_SERVICE_4_WIRE_COEX_SUPPORT,
184 	WMI_SERVICE_EXTENDED_NSS_SUPPORT,
185 	WMI_SERVICE_PROG_GPIO_BAND_SELECT,
186 	WMI_SERVICE_SMART_LOGGING_SUPPORT,
187 	WMI_SERVICE_TDLS_CONN_TRACKER_IN_HOST_MODE,
188 	WMI_SERVICE_TDLS_EXPLICIT_MODE_ONLY,
189 	WMI_SERVICE_MGMT_TX_WMI,
190 	WMI_SERVICE_TDLS_WIDER_BANDWIDTH,
191 	WMI_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS,
192 	WMI_SERVICE_HOST_DFS_CHECK_SUPPORT,
193 	WMI_SERVICE_TPC_STATS_FINAL,
194 	WMI_SERVICE_RESET_CHIP,
195 	WMI_SERVICE_SPOOF_MAC_SUPPORT,
196 	WMI_SERVICE_TX_DATA_ACK_RSSI,
197 	WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT,
198 	WMI_SERVICE_VDEV_DISABLE_4_ADDR_SRC_LRN_SUPPORT,
199 	WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT,
200 	WMI_SERVICE_THERM_THROT,
201 	WMI_SERVICE_RTT_RESPONDER_ROLE,
202 	WMI_SERVICE_PER_PACKET_SW_ENCRYPT,
203 	WMI_SERVICE_REPORT_AIRTIME,
204 	WMI_SERVICE_SYNC_DELETE_CMDS,
205 	WMI_SERVICE_TX_PWR_PER_PEER,
206 	WMI_SERVICE_SUPPORT_EXTEND_ADDRESS,
207 	WMI_SERVICE_PEER_TID_CONFIGS_SUPPORT,
208 	WMI_SERVICE_EXT_PEER_TID_CONFIGS_SUPPORT,
209 
210 	/* Remember to add the new value to wmi_service_name()! */
211 
212 	/* keep last */
213 	WMI_SERVICE_MAX,
214 };
215 
216 enum wmi_10x_service {
217 	WMI_10X_SERVICE_BEACON_OFFLOAD = 0,
218 	WMI_10X_SERVICE_SCAN_OFFLOAD,
219 	WMI_10X_SERVICE_ROAM_OFFLOAD,
220 	WMI_10X_SERVICE_BCN_MISS_OFFLOAD,
221 	WMI_10X_SERVICE_STA_PWRSAVE,
222 	WMI_10X_SERVICE_STA_ADVANCED_PWRSAVE,
223 	WMI_10X_SERVICE_AP_UAPSD,
224 	WMI_10X_SERVICE_AP_DFS,
225 	WMI_10X_SERVICE_11AC,
226 	WMI_10X_SERVICE_BLOCKACK,
227 	WMI_10X_SERVICE_PHYERR,
228 	WMI_10X_SERVICE_BCN_FILTER,
229 	WMI_10X_SERVICE_RTT,
230 	WMI_10X_SERVICE_RATECTRL,
231 	WMI_10X_SERVICE_WOW,
232 	WMI_10X_SERVICE_RATECTRL_CACHE,
233 	WMI_10X_SERVICE_IRAM_TIDS,
234 	WMI_10X_SERVICE_BURST,
235 
236 	/* introduced in 10.2 */
237 	WMI_10X_SERVICE_SMART_ANTENNA_SW_SUPPORT,
238 	WMI_10X_SERVICE_FORCE_FW_HANG,
239 	WMI_10X_SERVICE_SMART_ANTENNA_HW_SUPPORT,
240 	WMI_10X_SERVICE_ATF,
241 	WMI_10X_SERVICE_COEX_GPIO,
242 	WMI_10X_SERVICE_AUX_SPECTRAL_INTF,
243 	WMI_10X_SERVICE_AUX_CHAN_LOAD_INTF,
244 	WMI_10X_SERVICE_BSS_CHANNEL_INFO_64,
245 	WMI_10X_SERVICE_MESH,
246 	WMI_10X_SERVICE_EXT_RES_CFG_SUPPORT,
247 	WMI_10X_SERVICE_PEER_STATS,
248 	WMI_10X_SERVICE_RESET_CHIP,
249 	WMI_10X_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS,
250 	WMI_10X_SERVICE_VDEV_BCN_RATE_CONTROL,
251 	WMI_10X_SERVICE_PER_PACKET_SW_ENCRYPT,
252 	WMI_10X_SERVICE_BB_TIMING_CONFIG_SUPPORT,
253 };
254 
255 enum wmi_main_service {
256 	WMI_MAIN_SERVICE_BEACON_OFFLOAD = 0,
257 	WMI_MAIN_SERVICE_SCAN_OFFLOAD,
258 	WMI_MAIN_SERVICE_ROAM_OFFLOAD,
259 	WMI_MAIN_SERVICE_BCN_MISS_OFFLOAD,
260 	WMI_MAIN_SERVICE_STA_PWRSAVE,
261 	WMI_MAIN_SERVICE_STA_ADVANCED_PWRSAVE,
262 	WMI_MAIN_SERVICE_AP_UAPSD,
263 	WMI_MAIN_SERVICE_AP_DFS,
264 	WMI_MAIN_SERVICE_11AC,
265 	WMI_MAIN_SERVICE_BLOCKACK,
266 	WMI_MAIN_SERVICE_PHYERR,
267 	WMI_MAIN_SERVICE_BCN_FILTER,
268 	WMI_MAIN_SERVICE_RTT,
269 	WMI_MAIN_SERVICE_RATECTRL,
270 	WMI_MAIN_SERVICE_WOW,
271 	WMI_MAIN_SERVICE_RATECTRL_CACHE,
272 	WMI_MAIN_SERVICE_IRAM_TIDS,
273 	WMI_MAIN_SERVICE_ARPNS_OFFLOAD,
274 	WMI_MAIN_SERVICE_NLO,
275 	WMI_MAIN_SERVICE_GTK_OFFLOAD,
276 	WMI_MAIN_SERVICE_SCAN_SCH,
277 	WMI_MAIN_SERVICE_CSA_OFFLOAD,
278 	WMI_MAIN_SERVICE_CHATTER,
279 	WMI_MAIN_SERVICE_COEX_FREQAVOID,
280 	WMI_MAIN_SERVICE_PACKET_POWER_SAVE,
281 	WMI_MAIN_SERVICE_FORCE_FW_HANG,
282 	WMI_MAIN_SERVICE_GPIO,
283 	WMI_MAIN_SERVICE_STA_DTIM_PS_MODULATED_DTIM,
284 	WMI_MAIN_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG,
285 	WMI_MAIN_SERVICE_STA_UAPSD_VAR_AUTO_TRIG,
286 	WMI_MAIN_SERVICE_STA_KEEP_ALIVE,
287 	WMI_MAIN_SERVICE_TX_ENCAP,
288 };
289 
290 enum wmi_10_4_service {
291 	WMI_10_4_SERVICE_BEACON_OFFLOAD = 0,
292 	WMI_10_4_SERVICE_SCAN_OFFLOAD,
293 	WMI_10_4_SERVICE_ROAM_OFFLOAD,
294 	WMI_10_4_SERVICE_BCN_MISS_OFFLOAD,
295 	WMI_10_4_SERVICE_STA_PWRSAVE,
296 	WMI_10_4_SERVICE_STA_ADVANCED_PWRSAVE,
297 	WMI_10_4_SERVICE_AP_UAPSD,
298 	WMI_10_4_SERVICE_AP_DFS,
299 	WMI_10_4_SERVICE_11AC,
300 	WMI_10_4_SERVICE_BLOCKACK,
301 	WMI_10_4_SERVICE_PHYERR,
302 	WMI_10_4_SERVICE_BCN_FILTER,
303 	WMI_10_4_SERVICE_RTT,
304 	WMI_10_4_SERVICE_RATECTRL,
305 	WMI_10_4_SERVICE_WOW,
306 	WMI_10_4_SERVICE_RATECTRL_CACHE,
307 	WMI_10_4_SERVICE_IRAM_TIDS,
308 	WMI_10_4_SERVICE_BURST,
309 	WMI_10_4_SERVICE_SMART_ANTENNA_SW_SUPPORT,
310 	WMI_10_4_SERVICE_GTK_OFFLOAD,
311 	WMI_10_4_SERVICE_SCAN_SCH,
312 	WMI_10_4_SERVICE_CSA_OFFLOAD,
313 	WMI_10_4_SERVICE_CHATTER,
314 	WMI_10_4_SERVICE_COEX_FREQAVOID,
315 	WMI_10_4_SERVICE_PACKET_POWER_SAVE,
316 	WMI_10_4_SERVICE_FORCE_FW_HANG,
317 	WMI_10_4_SERVICE_SMART_ANTENNA_HW_SUPPORT,
318 	WMI_10_4_SERVICE_GPIO,
319 	WMI_10_4_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG,
320 	WMI_10_4_SERVICE_STA_UAPSD_VAR_AUTO_TRIG,
321 	WMI_10_4_SERVICE_STA_KEEP_ALIVE,
322 	WMI_10_4_SERVICE_TX_ENCAP,
323 	WMI_10_4_SERVICE_AP_PS_DETECT_OUT_OF_SYNC,
324 	WMI_10_4_SERVICE_EARLY_RX,
325 	WMI_10_4_SERVICE_ENHANCED_PROXY_STA,
326 	WMI_10_4_SERVICE_TT,
327 	WMI_10_4_SERVICE_ATF,
328 	WMI_10_4_SERVICE_PEER_CACHING,
329 	WMI_10_4_SERVICE_COEX_GPIO,
330 	WMI_10_4_SERVICE_AUX_SPECTRAL_INTF,
331 	WMI_10_4_SERVICE_AUX_CHAN_LOAD_INTF,
332 	WMI_10_4_SERVICE_BSS_CHANNEL_INFO_64,
333 	WMI_10_4_SERVICE_EXT_RES_CFG_SUPPORT,
334 	WMI_10_4_SERVICE_MESH_NON_11S,
335 	WMI_10_4_SERVICE_RESTRT_CHNL_SUPPORT,
336 	WMI_10_4_SERVICE_PEER_STATS,
337 	WMI_10_4_SERVICE_MESH_11S,
338 	WMI_10_4_SERVICE_PERIODIC_CHAN_STAT_SUPPORT,
339 	WMI_10_4_SERVICE_TX_MODE_PUSH_ONLY,
340 	WMI_10_4_SERVICE_TX_MODE_PUSH_PULL,
341 	WMI_10_4_SERVICE_TX_MODE_DYNAMIC,
342 	WMI_10_4_SERVICE_VDEV_RX_FILTER,
343 	WMI_10_4_SERVICE_BTCOEX,
344 	WMI_10_4_SERVICE_CHECK_CAL_VERSION,
345 	WMI_10_4_SERVICE_DBGLOG_WARN2,
346 	WMI_10_4_SERVICE_BTCOEX_DUTY_CYCLE,
347 	WMI_10_4_SERVICE_4_WIRE_COEX_SUPPORT,
348 	WMI_10_4_SERVICE_EXTENDED_NSS_SUPPORT,
349 	WMI_10_4_SERVICE_PROG_GPIO_BAND_SELECT,
350 	WMI_10_4_SERVICE_SMART_LOGGING_SUPPORT,
351 	WMI_10_4_SERVICE_TDLS,
352 	WMI_10_4_SERVICE_TDLS_OFFCHAN,
353 	WMI_10_4_SERVICE_TDLS_UAPSD_BUFFER_STA,
354 	WMI_10_4_SERVICE_TDLS_UAPSD_SLEEP_STA,
355 	WMI_10_4_SERVICE_TDLS_CONN_TRACKER_IN_HOST_MODE,
356 	WMI_10_4_SERVICE_TDLS_EXPLICIT_MODE_ONLY,
357 	WMI_10_4_SERVICE_TDLS_WIDER_BANDWIDTH,
358 	WMI_10_4_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS,
359 	WMI_10_4_SERVICE_HOST_DFS_CHECK_SUPPORT,
360 	WMI_10_4_SERVICE_TPC_STATS_FINAL,
361 	WMI_10_4_SERVICE_CFR_CAPTURE_SUPPORT,
362 	WMI_10_4_SERVICE_TX_DATA_ACK_RSSI,
363 	WMI_10_4_SERVICE_CFR_CAPTURE_IND_MSG_TYPE_LEGACY,
364 	WMI_10_4_SERVICE_PER_PACKET_SW_ENCRYPT,
365 	WMI_10_4_SERVICE_PEER_TID_CONFIGS_SUPPORT,
366 	WMI_10_4_SERVICE_VDEV_BCN_RATE_CONTROL,
367 	WMI_10_4_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT,
368 	WMI_10_4_SERVICE_HTT_ASSERT_TRIGGER_SUPPORT,
369 	WMI_10_4_SERVICE_VDEV_FILTER_NEIGHBOR_RX_PACKETS,
370 	WMI_10_4_SERVICE_VDEV_DISABLE_4_ADDR_SRC_LRN_SUPPORT,
371 	WMI_10_4_SERVICE_PEER_CHWIDTH_CHANGE,
372 	WMI_10_4_SERVICE_RX_FILTER_OUT_COUNT,
373 	WMI_10_4_SERVICE_RTT_RESPONDER_ROLE,
374 	WMI_10_4_SERVICE_EXT_PEER_TID_CONFIGS_SUPPORT,
375 	WMI_10_4_SERVICE_REPORT_AIRTIME,
376 	WMI_10_4_SERVICE_TX_PWR_PER_PEER,
377 	WMI_10_4_SERVICE_FETCH_PEER_TX_PN,
378 	WMI_10_4_SERVICE_MULTIPLE_VDEV_RESTART,
379 	WMI_10_4_SERVICE_ENHANCED_RADIO_COUNTERS,
380 	WMI_10_4_SERVICE_QINQ_SUPPORT,
381 	WMI_10_4_SERVICE_RESET_CHIP,
382 };
383 
wmi_service_name(enum wmi_service service_id)384 static inline char *wmi_service_name(enum wmi_service service_id)
385 {
386 #define SVCSTR(x) case x: return #x
387 
388 	switch (service_id) {
389 	SVCSTR(WMI_SERVICE_BEACON_OFFLOAD);
390 	SVCSTR(WMI_SERVICE_SCAN_OFFLOAD);
391 	SVCSTR(WMI_SERVICE_ROAM_OFFLOAD);
392 	SVCSTR(WMI_SERVICE_BCN_MISS_OFFLOAD);
393 	SVCSTR(WMI_SERVICE_STA_PWRSAVE);
394 	SVCSTR(WMI_SERVICE_STA_ADVANCED_PWRSAVE);
395 	SVCSTR(WMI_SERVICE_AP_UAPSD);
396 	SVCSTR(WMI_SERVICE_AP_DFS);
397 	SVCSTR(WMI_SERVICE_11AC);
398 	SVCSTR(WMI_SERVICE_BLOCKACK);
399 	SVCSTR(WMI_SERVICE_PHYERR);
400 	SVCSTR(WMI_SERVICE_BCN_FILTER);
401 	SVCSTR(WMI_SERVICE_RTT);
402 	SVCSTR(WMI_SERVICE_RATECTRL);
403 	SVCSTR(WMI_SERVICE_WOW);
404 	SVCSTR(WMI_SERVICE_RATECTRL_CACHE);
405 	SVCSTR(WMI_SERVICE_IRAM_TIDS);
406 	SVCSTR(WMI_SERVICE_ARPNS_OFFLOAD);
407 	SVCSTR(WMI_SERVICE_NLO);
408 	SVCSTR(WMI_SERVICE_GTK_OFFLOAD);
409 	SVCSTR(WMI_SERVICE_SCAN_SCH);
410 	SVCSTR(WMI_SERVICE_CSA_OFFLOAD);
411 	SVCSTR(WMI_SERVICE_CHATTER);
412 	SVCSTR(WMI_SERVICE_COEX_FREQAVOID);
413 	SVCSTR(WMI_SERVICE_PACKET_POWER_SAVE);
414 	SVCSTR(WMI_SERVICE_FORCE_FW_HANG);
415 	SVCSTR(WMI_SERVICE_GPIO);
416 	SVCSTR(WMI_SERVICE_STA_DTIM_PS_MODULATED_DTIM);
417 	SVCSTR(WMI_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG);
418 	SVCSTR(WMI_SERVICE_STA_UAPSD_VAR_AUTO_TRIG);
419 	SVCSTR(WMI_SERVICE_STA_KEEP_ALIVE);
420 	SVCSTR(WMI_SERVICE_TX_ENCAP);
421 	SVCSTR(WMI_SERVICE_BURST);
422 	SVCSTR(WMI_SERVICE_SMART_ANTENNA_SW_SUPPORT);
423 	SVCSTR(WMI_SERVICE_SMART_ANTENNA_HW_SUPPORT);
424 	SVCSTR(WMI_SERVICE_ROAM_SCAN_OFFLOAD);
425 	SVCSTR(WMI_SERVICE_AP_PS_DETECT_OUT_OF_SYNC);
426 	SVCSTR(WMI_SERVICE_EARLY_RX);
427 	SVCSTR(WMI_SERVICE_STA_SMPS);
428 	SVCSTR(WMI_SERVICE_FWTEST);
429 	SVCSTR(WMI_SERVICE_STA_WMMAC);
430 	SVCSTR(WMI_SERVICE_TDLS);
431 	SVCSTR(WMI_SERVICE_MCC_BCN_INTERVAL_CHANGE);
432 	SVCSTR(WMI_SERVICE_ADAPTIVE_OCS);
433 	SVCSTR(WMI_SERVICE_BA_SSN_SUPPORT);
434 	SVCSTR(WMI_SERVICE_FILTER_IPSEC_NATKEEPALIVE);
435 	SVCSTR(WMI_SERVICE_WLAN_HB);
436 	SVCSTR(WMI_SERVICE_LTE_ANT_SHARE_SUPPORT);
437 	SVCSTR(WMI_SERVICE_BATCH_SCAN);
438 	SVCSTR(WMI_SERVICE_QPOWER);
439 	SVCSTR(WMI_SERVICE_PLMREQ);
440 	SVCSTR(WMI_SERVICE_THERMAL_MGMT);
441 	SVCSTR(WMI_SERVICE_RMC);
442 	SVCSTR(WMI_SERVICE_MHF_OFFLOAD);
443 	SVCSTR(WMI_SERVICE_COEX_SAR);
444 	SVCSTR(WMI_SERVICE_BCN_TXRATE_OVERRIDE);
445 	SVCSTR(WMI_SERVICE_NAN);
446 	SVCSTR(WMI_SERVICE_L1SS_STAT);
447 	SVCSTR(WMI_SERVICE_ESTIMATE_LINKSPEED);
448 	SVCSTR(WMI_SERVICE_OBSS_SCAN);
449 	SVCSTR(WMI_SERVICE_TDLS_OFFCHAN);
450 	SVCSTR(WMI_SERVICE_TDLS_UAPSD_BUFFER_STA);
451 	SVCSTR(WMI_SERVICE_TDLS_UAPSD_SLEEP_STA);
452 	SVCSTR(WMI_SERVICE_IBSS_PWRSAVE);
453 	SVCSTR(WMI_SERVICE_LPASS);
454 	SVCSTR(WMI_SERVICE_EXTSCAN);
455 	SVCSTR(WMI_SERVICE_D0WOW);
456 	SVCSTR(WMI_SERVICE_HSOFFLOAD);
457 	SVCSTR(WMI_SERVICE_ROAM_HO_OFFLOAD);
458 	SVCSTR(WMI_SERVICE_RX_FULL_REORDER);
459 	SVCSTR(WMI_SERVICE_DHCP_OFFLOAD);
460 	SVCSTR(WMI_SERVICE_STA_RX_IPA_OFFLOAD_SUPPORT);
461 	SVCSTR(WMI_SERVICE_MDNS_OFFLOAD);
462 	SVCSTR(WMI_SERVICE_SAP_AUTH_OFFLOAD);
463 	SVCSTR(WMI_SERVICE_ATF);
464 	SVCSTR(WMI_SERVICE_COEX_GPIO);
465 	SVCSTR(WMI_SERVICE_ENHANCED_PROXY_STA);
466 	SVCSTR(WMI_SERVICE_TT);
467 	SVCSTR(WMI_SERVICE_PEER_CACHING);
468 	SVCSTR(WMI_SERVICE_AUX_SPECTRAL_INTF);
469 	SVCSTR(WMI_SERVICE_AUX_CHAN_LOAD_INTF);
470 	SVCSTR(WMI_SERVICE_BSS_CHANNEL_INFO_64);
471 	SVCSTR(WMI_SERVICE_EXT_RES_CFG_SUPPORT);
472 	SVCSTR(WMI_SERVICE_MESH_11S);
473 	SVCSTR(WMI_SERVICE_MESH_NON_11S);
474 	SVCSTR(WMI_SERVICE_PEER_STATS);
475 	SVCSTR(WMI_SERVICE_RESTRT_CHNL_SUPPORT);
476 	SVCSTR(WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT);
477 	SVCSTR(WMI_SERVICE_TX_MODE_PUSH_ONLY);
478 	SVCSTR(WMI_SERVICE_TX_MODE_PUSH_PULL);
479 	SVCSTR(WMI_SERVICE_TX_MODE_DYNAMIC);
480 	SVCSTR(WMI_SERVICE_VDEV_RX_FILTER);
481 	SVCSTR(WMI_SERVICE_BTCOEX);
482 	SVCSTR(WMI_SERVICE_CHECK_CAL_VERSION);
483 	SVCSTR(WMI_SERVICE_DBGLOG_WARN2);
484 	SVCSTR(WMI_SERVICE_BTCOEX_DUTY_CYCLE);
485 	SVCSTR(WMI_SERVICE_4_WIRE_COEX_SUPPORT);
486 	SVCSTR(WMI_SERVICE_EXTENDED_NSS_SUPPORT);
487 	SVCSTR(WMI_SERVICE_PROG_GPIO_BAND_SELECT);
488 	SVCSTR(WMI_SERVICE_SMART_LOGGING_SUPPORT);
489 	SVCSTR(WMI_SERVICE_TDLS_CONN_TRACKER_IN_HOST_MODE);
490 	SVCSTR(WMI_SERVICE_TDLS_EXPLICIT_MODE_ONLY);
491 	SVCSTR(WMI_SERVICE_MGMT_TX_WMI);
492 	SVCSTR(WMI_SERVICE_TDLS_WIDER_BANDWIDTH);
493 	SVCSTR(WMI_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS);
494 	SVCSTR(WMI_SERVICE_HOST_DFS_CHECK_SUPPORT);
495 	SVCSTR(WMI_SERVICE_TPC_STATS_FINAL);
496 	SVCSTR(WMI_SERVICE_RESET_CHIP);
497 	SVCSTR(WMI_SERVICE_SPOOF_MAC_SUPPORT);
498 	SVCSTR(WMI_SERVICE_TX_DATA_ACK_RSSI);
499 	SVCSTR(WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT);
500 	SVCSTR(WMI_SERVICE_VDEV_DISABLE_4_ADDR_SRC_LRN_SUPPORT);
501 	SVCSTR(WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT);
502 	SVCSTR(WMI_SERVICE_THERM_THROT);
503 	SVCSTR(WMI_SERVICE_RTT_RESPONDER_ROLE);
504 	SVCSTR(WMI_SERVICE_PER_PACKET_SW_ENCRYPT);
505 	SVCSTR(WMI_SERVICE_REPORT_AIRTIME);
506 	SVCSTR(WMI_SERVICE_SYNC_DELETE_CMDS);
507 	SVCSTR(WMI_SERVICE_TX_PWR_PER_PEER);
508 	SVCSTR(WMI_SERVICE_SUPPORT_EXTEND_ADDRESS);
509 	SVCSTR(WMI_SERVICE_PEER_TID_CONFIGS_SUPPORT);
510 	SVCSTR(WMI_SERVICE_EXT_PEER_TID_CONFIGS_SUPPORT);
511 
512 	case WMI_SERVICE_MAX:
513 		return NULL;
514 	}
515 
516 #undef SVCSTR
517 
518 	return NULL;
519 }
520 
521 #define WMI_SERVICE_IS_ENABLED(wmi_svc_bmap, svc_id, len) \
522 	((svc_id) < (len) && \
523 	 __le32_to_cpu((wmi_svc_bmap)[(svc_id) / (sizeof(u32))]) & \
524 	 BIT((svc_id) % (sizeof(u32))))
525 
526 /* This extension is required to accommodate new services, current limit
527  * for wmi_services is 64 as target is using only 4-bits of each 32-bit
528  * wmi_service word. Extending this to make use of remaining unused bits
529  * for new services.
530  */
531 #define WMI_EXT_SERVICE_IS_ENABLED(wmi_svc_bmap, svc_id, len) \
532 	((svc_id) >= (len) && \
533 	__le32_to_cpu((wmi_svc_bmap)[((svc_id) - (len)) / 28]) & \
534 	BIT(((((svc_id) - (len)) % 28) & 0x1f) + 4))
535 
536 #define SVCMAP(x, y, len) \
537 	do { \
538 		if ((WMI_SERVICE_IS_ENABLED((in), (x), (len))) || \
539 		    (WMI_EXT_SERVICE_IS_ENABLED((in), (x), (len)))) \
540 			__set_bit(y, out); \
541 	} while (0)
542 
wmi_10x_svc_map(const __le32 * in,unsigned long * out,size_t len)543 static inline void wmi_10x_svc_map(const __le32 *in, unsigned long *out,
544 				   size_t len)
545 {
546 	SVCMAP(WMI_10X_SERVICE_BEACON_OFFLOAD,
547 	       WMI_SERVICE_BEACON_OFFLOAD, len);
548 	SVCMAP(WMI_10X_SERVICE_SCAN_OFFLOAD,
549 	       WMI_SERVICE_SCAN_OFFLOAD, len);
550 	SVCMAP(WMI_10X_SERVICE_ROAM_OFFLOAD,
551 	       WMI_SERVICE_ROAM_OFFLOAD, len);
552 	SVCMAP(WMI_10X_SERVICE_BCN_MISS_OFFLOAD,
553 	       WMI_SERVICE_BCN_MISS_OFFLOAD, len);
554 	SVCMAP(WMI_10X_SERVICE_STA_PWRSAVE,
555 	       WMI_SERVICE_STA_PWRSAVE, len);
556 	SVCMAP(WMI_10X_SERVICE_STA_ADVANCED_PWRSAVE,
557 	       WMI_SERVICE_STA_ADVANCED_PWRSAVE, len);
558 	SVCMAP(WMI_10X_SERVICE_AP_UAPSD,
559 	       WMI_SERVICE_AP_UAPSD, len);
560 	SVCMAP(WMI_10X_SERVICE_AP_DFS,
561 	       WMI_SERVICE_AP_DFS, len);
562 	SVCMAP(WMI_10X_SERVICE_11AC,
563 	       WMI_SERVICE_11AC, len);
564 	SVCMAP(WMI_10X_SERVICE_BLOCKACK,
565 	       WMI_SERVICE_BLOCKACK, len);
566 	SVCMAP(WMI_10X_SERVICE_PHYERR,
567 	       WMI_SERVICE_PHYERR, len);
568 	SVCMAP(WMI_10X_SERVICE_BCN_FILTER,
569 	       WMI_SERVICE_BCN_FILTER, len);
570 	SVCMAP(WMI_10X_SERVICE_RTT,
571 	       WMI_SERVICE_RTT, len);
572 	SVCMAP(WMI_10X_SERVICE_RATECTRL,
573 	       WMI_SERVICE_RATECTRL, len);
574 	SVCMAP(WMI_10X_SERVICE_WOW,
575 	       WMI_SERVICE_WOW, len);
576 	SVCMAP(WMI_10X_SERVICE_RATECTRL_CACHE,
577 	       WMI_SERVICE_RATECTRL_CACHE, len);
578 	SVCMAP(WMI_10X_SERVICE_IRAM_TIDS,
579 	       WMI_SERVICE_IRAM_TIDS, len);
580 	SVCMAP(WMI_10X_SERVICE_BURST,
581 	       WMI_SERVICE_BURST, len);
582 	SVCMAP(WMI_10X_SERVICE_SMART_ANTENNA_SW_SUPPORT,
583 	       WMI_SERVICE_SMART_ANTENNA_SW_SUPPORT, len);
584 	SVCMAP(WMI_10X_SERVICE_FORCE_FW_HANG,
585 	       WMI_SERVICE_FORCE_FW_HANG, len);
586 	SVCMAP(WMI_10X_SERVICE_SMART_ANTENNA_HW_SUPPORT,
587 	       WMI_SERVICE_SMART_ANTENNA_HW_SUPPORT, len);
588 	SVCMAP(WMI_10X_SERVICE_ATF,
589 	       WMI_SERVICE_ATF, len);
590 	SVCMAP(WMI_10X_SERVICE_COEX_GPIO,
591 	       WMI_SERVICE_COEX_GPIO, len);
592 	SVCMAP(WMI_10X_SERVICE_AUX_SPECTRAL_INTF,
593 	       WMI_SERVICE_AUX_SPECTRAL_INTF, len);
594 	SVCMAP(WMI_10X_SERVICE_AUX_CHAN_LOAD_INTF,
595 	       WMI_SERVICE_AUX_CHAN_LOAD_INTF, len);
596 	SVCMAP(WMI_10X_SERVICE_BSS_CHANNEL_INFO_64,
597 	       WMI_SERVICE_BSS_CHANNEL_INFO_64, len);
598 	SVCMAP(WMI_10X_SERVICE_MESH,
599 	       WMI_SERVICE_MESH_11S, len);
600 	SVCMAP(WMI_10X_SERVICE_EXT_RES_CFG_SUPPORT,
601 	       WMI_SERVICE_EXT_RES_CFG_SUPPORT, len);
602 	SVCMAP(WMI_10X_SERVICE_PEER_STATS,
603 	       WMI_SERVICE_PEER_STATS, len);
604 	SVCMAP(WMI_10X_SERVICE_RESET_CHIP,
605 	       WMI_SERVICE_RESET_CHIP, len);
606 	SVCMAP(WMI_10X_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS,
607 	       WMI_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS, len);
608 	SVCMAP(WMI_10X_SERVICE_BB_TIMING_CONFIG_SUPPORT,
609 	       WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT, len);
610 	SVCMAP(WMI_10X_SERVICE_PER_PACKET_SW_ENCRYPT,
611 	       WMI_SERVICE_PER_PACKET_SW_ENCRYPT, len);
612 }
613 
wmi_main_svc_map(const __le32 * in,unsigned long * out,size_t len)614 static inline void wmi_main_svc_map(const __le32 *in, unsigned long *out,
615 				    size_t len)
616 {
617 	SVCMAP(WMI_MAIN_SERVICE_BEACON_OFFLOAD,
618 	       WMI_SERVICE_BEACON_OFFLOAD, len);
619 	SVCMAP(WMI_MAIN_SERVICE_SCAN_OFFLOAD,
620 	       WMI_SERVICE_SCAN_OFFLOAD, len);
621 	SVCMAP(WMI_MAIN_SERVICE_ROAM_OFFLOAD,
622 	       WMI_SERVICE_ROAM_OFFLOAD, len);
623 	SVCMAP(WMI_MAIN_SERVICE_BCN_MISS_OFFLOAD,
624 	       WMI_SERVICE_BCN_MISS_OFFLOAD, len);
625 	SVCMAP(WMI_MAIN_SERVICE_STA_PWRSAVE,
626 	       WMI_SERVICE_STA_PWRSAVE, len);
627 	SVCMAP(WMI_MAIN_SERVICE_STA_ADVANCED_PWRSAVE,
628 	       WMI_SERVICE_STA_ADVANCED_PWRSAVE, len);
629 	SVCMAP(WMI_MAIN_SERVICE_AP_UAPSD,
630 	       WMI_SERVICE_AP_UAPSD, len);
631 	SVCMAP(WMI_MAIN_SERVICE_AP_DFS,
632 	       WMI_SERVICE_AP_DFS, len);
633 	SVCMAP(WMI_MAIN_SERVICE_11AC,
634 	       WMI_SERVICE_11AC, len);
635 	SVCMAP(WMI_MAIN_SERVICE_BLOCKACK,
636 	       WMI_SERVICE_BLOCKACK, len);
637 	SVCMAP(WMI_MAIN_SERVICE_PHYERR,
638 	       WMI_SERVICE_PHYERR, len);
639 	SVCMAP(WMI_MAIN_SERVICE_BCN_FILTER,
640 	       WMI_SERVICE_BCN_FILTER, len);
641 	SVCMAP(WMI_MAIN_SERVICE_RTT,
642 	       WMI_SERVICE_RTT, len);
643 	SVCMAP(WMI_MAIN_SERVICE_RATECTRL,
644 	       WMI_SERVICE_RATECTRL, len);
645 	SVCMAP(WMI_MAIN_SERVICE_WOW,
646 	       WMI_SERVICE_WOW, len);
647 	SVCMAP(WMI_MAIN_SERVICE_RATECTRL_CACHE,
648 	       WMI_SERVICE_RATECTRL_CACHE, len);
649 	SVCMAP(WMI_MAIN_SERVICE_IRAM_TIDS,
650 	       WMI_SERVICE_IRAM_TIDS, len);
651 	SVCMAP(WMI_MAIN_SERVICE_ARPNS_OFFLOAD,
652 	       WMI_SERVICE_ARPNS_OFFLOAD, len);
653 	SVCMAP(WMI_MAIN_SERVICE_NLO,
654 	       WMI_SERVICE_NLO, len);
655 	SVCMAP(WMI_MAIN_SERVICE_GTK_OFFLOAD,
656 	       WMI_SERVICE_GTK_OFFLOAD, len);
657 	SVCMAP(WMI_MAIN_SERVICE_SCAN_SCH,
658 	       WMI_SERVICE_SCAN_SCH, len);
659 	SVCMAP(WMI_MAIN_SERVICE_CSA_OFFLOAD,
660 	       WMI_SERVICE_CSA_OFFLOAD, len);
661 	SVCMAP(WMI_MAIN_SERVICE_CHATTER,
662 	       WMI_SERVICE_CHATTER, len);
663 	SVCMAP(WMI_MAIN_SERVICE_COEX_FREQAVOID,
664 	       WMI_SERVICE_COEX_FREQAVOID, len);
665 	SVCMAP(WMI_MAIN_SERVICE_PACKET_POWER_SAVE,
666 	       WMI_SERVICE_PACKET_POWER_SAVE, len);
667 	SVCMAP(WMI_MAIN_SERVICE_FORCE_FW_HANG,
668 	       WMI_SERVICE_FORCE_FW_HANG, len);
669 	SVCMAP(WMI_MAIN_SERVICE_GPIO,
670 	       WMI_SERVICE_GPIO, len);
671 	SVCMAP(WMI_MAIN_SERVICE_STA_DTIM_PS_MODULATED_DTIM,
672 	       WMI_SERVICE_STA_DTIM_PS_MODULATED_DTIM, len);
673 	SVCMAP(WMI_MAIN_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG,
674 	       WMI_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG, len);
675 	SVCMAP(WMI_MAIN_SERVICE_STA_UAPSD_VAR_AUTO_TRIG,
676 	       WMI_SERVICE_STA_UAPSD_VAR_AUTO_TRIG, len);
677 	SVCMAP(WMI_MAIN_SERVICE_STA_KEEP_ALIVE,
678 	       WMI_SERVICE_STA_KEEP_ALIVE, len);
679 	SVCMAP(WMI_MAIN_SERVICE_TX_ENCAP,
680 	       WMI_SERVICE_TX_ENCAP, len);
681 }
682 
wmi_10_4_svc_map(const __le32 * in,unsigned long * out,size_t len)683 static inline void wmi_10_4_svc_map(const __le32 *in, unsigned long *out,
684 				    size_t len)
685 {
686 	SVCMAP(WMI_10_4_SERVICE_BEACON_OFFLOAD,
687 	       WMI_SERVICE_BEACON_OFFLOAD, len);
688 	SVCMAP(WMI_10_4_SERVICE_SCAN_OFFLOAD,
689 	       WMI_SERVICE_SCAN_OFFLOAD, len);
690 	SVCMAP(WMI_10_4_SERVICE_ROAM_OFFLOAD,
691 	       WMI_SERVICE_ROAM_OFFLOAD, len);
692 	SVCMAP(WMI_10_4_SERVICE_BCN_MISS_OFFLOAD,
693 	       WMI_SERVICE_BCN_MISS_OFFLOAD, len);
694 	SVCMAP(WMI_10_4_SERVICE_STA_PWRSAVE,
695 	       WMI_SERVICE_STA_PWRSAVE, len);
696 	SVCMAP(WMI_10_4_SERVICE_STA_ADVANCED_PWRSAVE,
697 	       WMI_SERVICE_STA_ADVANCED_PWRSAVE, len);
698 	SVCMAP(WMI_10_4_SERVICE_AP_UAPSD,
699 	       WMI_SERVICE_AP_UAPSD, len);
700 	SVCMAP(WMI_10_4_SERVICE_AP_DFS,
701 	       WMI_SERVICE_AP_DFS, len);
702 	SVCMAP(WMI_10_4_SERVICE_11AC,
703 	       WMI_SERVICE_11AC, len);
704 	SVCMAP(WMI_10_4_SERVICE_BLOCKACK,
705 	       WMI_SERVICE_BLOCKACK, len);
706 	SVCMAP(WMI_10_4_SERVICE_PHYERR,
707 	       WMI_SERVICE_PHYERR, len);
708 	SVCMAP(WMI_10_4_SERVICE_BCN_FILTER,
709 	       WMI_SERVICE_BCN_FILTER, len);
710 	SVCMAP(WMI_10_4_SERVICE_RTT,
711 	       WMI_SERVICE_RTT, len);
712 	SVCMAP(WMI_10_4_SERVICE_RATECTRL,
713 	       WMI_SERVICE_RATECTRL, len);
714 	SVCMAP(WMI_10_4_SERVICE_WOW,
715 	       WMI_SERVICE_WOW, len);
716 	SVCMAP(WMI_10_4_SERVICE_RATECTRL_CACHE,
717 	       WMI_SERVICE_RATECTRL_CACHE, len);
718 	SVCMAP(WMI_10_4_SERVICE_IRAM_TIDS,
719 	       WMI_SERVICE_IRAM_TIDS, len);
720 	SVCMAP(WMI_10_4_SERVICE_BURST,
721 	       WMI_SERVICE_BURST, len);
722 	SVCMAP(WMI_10_4_SERVICE_SMART_ANTENNA_SW_SUPPORT,
723 	       WMI_SERVICE_SMART_ANTENNA_SW_SUPPORT, len);
724 	SVCMAP(WMI_10_4_SERVICE_GTK_OFFLOAD,
725 	       WMI_SERVICE_GTK_OFFLOAD, len);
726 	SVCMAP(WMI_10_4_SERVICE_SCAN_SCH,
727 	       WMI_SERVICE_SCAN_SCH, len);
728 	SVCMAP(WMI_10_4_SERVICE_CSA_OFFLOAD,
729 	       WMI_SERVICE_CSA_OFFLOAD, len);
730 	SVCMAP(WMI_10_4_SERVICE_CHATTER,
731 	       WMI_SERVICE_CHATTER, len);
732 	SVCMAP(WMI_10_4_SERVICE_COEX_FREQAVOID,
733 	       WMI_SERVICE_COEX_FREQAVOID, len);
734 	SVCMAP(WMI_10_4_SERVICE_PACKET_POWER_SAVE,
735 	       WMI_SERVICE_PACKET_POWER_SAVE, len);
736 	SVCMAP(WMI_10_4_SERVICE_FORCE_FW_HANG,
737 	       WMI_SERVICE_FORCE_FW_HANG, len);
738 	SVCMAP(WMI_10_4_SERVICE_SMART_ANTENNA_HW_SUPPORT,
739 	       WMI_SERVICE_SMART_ANTENNA_HW_SUPPORT, len);
740 	SVCMAP(WMI_10_4_SERVICE_GPIO,
741 	       WMI_SERVICE_GPIO, len);
742 	SVCMAP(WMI_10_4_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG,
743 	       WMI_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG, len);
744 	SVCMAP(WMI_10_4_SERVICE_STA_UAPSD_VAR_AUTO_TRIG,
745 	       WMI_SERVICE_STA_UAPSD_VAR_AUTO_TRIG, len);
746 	SVCMAP(WMI_10_4_SERVICE_STA_KEEP_ALIVE,
747 	       WMI_SERVICE_STA_KEEP_ALIVE, len);
748 	SVCMAP(WMI_10_4_SERVICE_TX_ENCAP,
749 	       WMI_SERVICE_TX_ENCAP, len);
750 	SVCMAP(WMI_10_4_SERVICE_AP_PS_DETECT_OUT_OF_SYNC,
751 	       WMI_SERVICE_AP_PS_DETECT_OUT_OF_SYNC, len);
752 	SVCMAP(WMI_10_4_SERVICE_EARLY_RX,
753 	       WMI_SERVICE_EARLY_RX, len);
754 	SVCMAP(WMI_10_4_SERVICE_ENHANCED_PROXY_STA,
755 	       WMI_SERVICE_ENHANCED_PROXY_STA, len);
756 	SVCMAP(WMI_10_4_SERVICE_TT,
757 	       WMI_SERVICE_TT, len);
758 	SVCMAP(WMI_10_4_SERVICE_ATF,
759 	       WMI_SERVICE_ATF, len);
760 	SVCMAP(WMI_10_4_SERVICE_PEER_CACHING,
761 	       WMI_SERVICE_PEER_CACHING, len);
762 	SVCMAP(WMI_10_4_SERVICE_COEX_GPIO,
763 	       WMI_SERVICE_COEX_GPIO, len);
764 	SVCMAP(WMI_10_4_SERVICE_AUX_SPECTRAL_INTF,
765 	       WMI_SERVICE_AUX_SPECTRAL_INTF, len);
766 	SVCMAP(WMI_10_4_SERVICE_AUX_CHAN_LOAD_INTF,
767 	       WMI_SERVICE_AUX_CHAN_LOAD_INTF, len);
768 	SVCMAP(WMI_10_4_SERVICE_BSS_CHANNEL_INFO_64,
769 	       WMI_SERVICE_BSS_CHANNEL_INFO_64, len);
770 	SVCMAP(WMI_10_4_SERVICE_EXT_RES_CFG_SUPPORT,
771 	       WMI_SERVICE_EXT_RES_CFG_SUPPORT, len);
772 	SVCMAP(WMI_10_4_SERVICE_MESH_NON_11S,
773 	       WMI_SERVICE_MESH_NON_11S, len);
774 	SVCMAP(WMI_10_4_SERVICE_RESTRT_CHNL_SUPPORT,
775 	       WMI_SERVICE_RESTRT_CHNL_SUPPORT, len);
776 	SVCMAP(WMI_10_4_SERVICE_PEER_STATS,
777 	       WMI_SERVICE_PEER_STATS, len);
778 	SVCMAP(WMI_10_4_SERVICE_MESH_11S,
779 	       WMI_SERVICE_MESH_11S, len);
780 	SVCMAP(WMI_10_4_SERVICE_PERIODIC_CHAN_STAT_SUPPORT,
781 	       WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT, len);
782 	SVCMAP(WMI_10_4_SERVICE_TX_MODE_PUSH_ONLY,
783 	       WMI_SERVICE_TX_MODE_PUSH_ONLY, len);
784 	SVCMAP(WMI_10_4_SERVICE_TX_MODE_PUSH_PULL,
785 	       WMI_SERVICE_TX_MODE_PUSH_PULL, len);
786 	SVCMAP(WMI_10_4_SERVICE_TX_MODE_DYNAMIC,
787 	       WMI_SERVICE_TX_MODE_DYNAMIC, len);
788 	SVCMAP(WMI_10_4_SERVICE_VDEV_RX_FILTER,
789 	       WMI_SERVICE_VDEV_RX_FILTER, len);
790 	SVCMAP(WMI_10_4_SERVICE_BTCOEX,
791 	       WMI_SERVICE_BTCOEX, len);
792 	SVCMAP(WMI_10_4_SERVICE_CHECK_CAL_VERSION,
793 	       WMI_SERVICE_CHECK_CAL_VERSION, len);
794 	SVCMAP(WMI_10_4_SERVICE_DBGLOG_WARN2,
795 	       WMI_SERVICE_DBGLOG_WARN2, len);
796 	SVCMAP(WMI_10_4_SERVICE_BTCOEX_DUTY_CYCLE,
797 	       WMI_SERVICE_BTCOEX_DUTY_CYCLE, len);
798 	SVCMAP(WMI_10_4_SERVICE_4_WIRE_COEX_SUPPORT,
799 	       WMI_SERVICE_4_WIRE_COEX_SUPPORT, len);
800 	SVCMAP(WMI_10_4_SERVICE_EXTENDED_NSS_SUPPORT,
801 	       WMI_SERVICE_EXTENDED_NSS_SUPPORT, len);
802 	SVCMAP(WMI_10_4_SERVICE_PROG_GPIO_BAND_SELECT,
803 	       WMI_SERVICE_PROG_GPIO_BAND_SELECT, len);
804 	SVCMAP(WMI_10_4_SERVICE_SMART_LOGGING_SUPPORT,
805 	       WMI_SERVICE_SMART_LOGGING_SUPPORT, len);
806 	SVCMAP(WMI_10_4_SERVICE_TDLS,
807 	       WMI_SERVICE_TDLS, len);
808 	SVCMAP(WMI_10_4_SERVICE_TDLS_OFFCHAN,
809 	       WMI_SERVICE_TDLS_OFFCHAN, len);
810 	SVCMAP(WMI_10_4_SERVICE_TDLS_UAPSD_BUFFER_STA,
811 	       WMI_SERVICE_TDLS_UAPSD_BUFFER_STA, len);
812 	SVCMAP(WMI_10_4_SERVICE_TDLS_UAPSD_SLEEP_STA,
813 	       WMI_SERVICE_TDLS_UAPSD_SLEEP_STA, len);
814 	SVCMAP(WMI_10_4_SERVICE_TDLS_CONN_TRACKER_IN_HOST_MODE,
815 	       WMI_SERVICE_TDLS_CONN_TRACKER_IN_HOST_MODE, len);
816 	SVCMAP(WMI_10_4_SERVICE_TDLS_EXPLICIT_MODE_ONLY,
817 	       WMI_SERVICE_TDLS_EXPLICIT_MODE_ONLY, len);
818 	SVCMAP(WMI_10_4_SERVICE_TDLS_WIDER_BANDWIDTH,
819 	       WMI_SERVICE_TDLS_WIDER_BANDWIDTH, len);
820 	SVCMAP(WMI_10_4_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS,
821 	       WMI_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS, len);
822 	SVCMAP(WMI_10_4_SERVICE_HOST_DFS_CHECK_SUPPORT,
823 	       WMI_SERVICE_HOST_DFS_CHECK_SUPPORT, len);
824 	SVCMAP(WMI_10_4_SERVICE_TPC_STATS_FINAL,
825 	       WMI_SERVICE_TPC_STATS_FINAL, len);
826 	SVCMAP(WMI_10_4_SERVICE_TX_DATA_ACK_RSSI,
827 	       WMI_SERVICE_TX_DATA_ACK_RSSI, len);
828 	SVCMAP(WMI_10_4_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT,
829 	       WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, len);
830 	SVCMAP(WMI_10_4_SERVICE_VDEV_DISABLE_4_ADDR_SRC_LRN_SUPPORT,
831 	       WMI_SERVICE_VDEV_DISABLE_4_ADDR_SRC_LRN_SUPPORT, len);
832 	SVCMAP(WMI_10_4_SERVICE_RTT_RESPONDER_ROLE,
833 	       WMI_SERVICE_RTT_RESPONDER_ROLE, len);
834 	SVCMAP(WMI_10_4_SERVICE_PER_PACKET_SW_ENCRYPT,
835 	       WMI_SERVICE_PER_PACKET_SW_ENCRYPT, len);
836 	SVCMAP(WMI_10_4_SERVICE_REPORT_AIRTIME,
837 	       WMI_SERVICE_REPORT_AIRTIME, len);
838 	SVCMAP(WMI_10_4_SERVICE_TX_PWR_PER_PEER,
839 	       WMI_SERVICE_TX_PWR_PER_PEER, len);
840 	SVCMAP(WMI_10_4_SERVICE_RESET_CHIP,
841 	       WMI_SERVICE_RESET_CHIP, len);
842 	SVCMAP(WMI_10_4_SERVICE_PEER_TID_CONFIGS_SUPPORT,
843 	       WMI_SERVICE_PEER_TID_CONFIGS_SUPPORT, len);
844 	SVCMAP(WMI_10_4_SERVICE_EXT_PEER_TID_CONFIGS_SUPPORT,
845 	       WMI_SERVICE_PEER_TID_CONFIGS_SUPPORT, len);
846 }
847 
848 #undef SVCMAP
849 
850 /* 2 word representation of MAC addr */
851 struct wmi_mac_addr {
852 	union {
853 		u8 addr[6];
854 		struct {
855 			u32 word0;
856 			u32 word1;
857 		} __packed;
858 	} __packed;
859 } __packed;
860 
861 struct wmi_cmd_map {
862 	u32 init_cmdid;
863 	u32 start_scan_cmdid;
864 	u32 stop_scan_cmdid;
865 	u32 scan_chan_list_cmdid;
866 	u32 scan_sch_prio_tbl_cmdid;
867 	u32 scan_prob_req_oui_cmdid;
868 	u32 pdev_set_regdomain_cmdid;
869 	u32 pdev_set_channel_cmdid;
870 	u32 pdev_set_param_cmdid;
871 	u32 pdev_pktlog_enable_cmdid;
872 	u32 pdev_pktlog_disable_cmdid;
873 	u32 pdev_set_wmm_params_cmdid;
874 	u32 pdev_set_ht_cap_ie_cmdid;
875 	u32 pdev_set_vht_cap_ie_cmdid;
876 	u32 pdev_set_dscp_tid_map_cmdid;
877 	u32 pdev_set_quiet_mode_cmdid;
878 	u32 pdev_green_ap_ps_enable_cmdid;
879 	u32 pdev_get_tpc_config_cmdid;
880 	u32 pdev_set_base_macaddr_cmdid;
881 	u32 vdev_create_cmdid;
882 	u32 vdev_delete_cmdid;
883 	u32 vdev_start_request_cmdid;
884 	u32 vdev_restart_request_cmdid;
885 	u32 vdev_up_cmdid;
886 	u32 vdev_stop_cmdid;
887 	u32 vdev_down_cmdid;
888 	u32 vdev_set_param_cmdid;
889 	u32 vdev_install_key_cmdid;
890 	u32 peer_create_cmdid;
891 	u32 peer_delete_cmdid;
892 	u32 peer_flush_tids_cmdid;
893 	u32 peer_set_param_cmdid;
894 	u32 peer_assoc_cmdid;
895 	u32 peer_add_wds_entry_cmdid;
896 	u32 peer_remove_wds_entry_cmdid;
897 	u32 peer_mcast_group_cmdid;
898 	u32 bcn_tx_cmdid;
899 	u32 pdev_send_bcn_cmdid;
900 	u32 bcn_tmpl_cmdid;
901 	u32 bcn_filter_rx_cmdid;
902 	u32 prb_req_filter_rx_cmdid;
903 	u32 mgmt_tx_cmdid;
904 	u32 mgmt_tx_send_cmdid;
905 	u32 prb_tmpl_cmdid;
906 	u32 addba_clear_resp_cmdid;
907 	u32 addba_send_cmdid;
908 	u32 addba_status_cmdid;
909 	u32 delba_send_cmdid;
910 	u32 addba_set_resp_cmdid;
911 	u32 send_singleamsdu_cmdid;
912 	u32 sta_powersave_mode_cmdid;
913 	u32 sta_powersave_param_cmdid;
914 	u32 sta_mimo_ps_mode_cmdid;
915 	u32 pdev_dfs_enable_cmdid;
916 	u32 pdev_dfs_disable_cmdid;
917 	u32 roam_scan_mode;
918 	u32 roam_scan_rssi_threshold;
919 	u32 roam_scan_period;
920 	u32 roam_scan_rssi_change_threshold;
921 	u32 roam_ap_profile;
922 	u32 ofl_scan_add_ap_profile;
923 	u32 ofl_scan_remove_ap_profile;
924 	u32 ofl_scan_period;
925 	u32 p2p_dev_set_device_info;
926 	u32 p2p_dev_set_discoverability;
927 	u32 p2p_go_set_beacon_ie;
928 	u32 p2p_go_set_probe_resp_ie;
929 	u32 p2p_set_vendor_ie_data_cmdid;
930 	u32 ap_ps_peer_param_cmdid;
931 	u32 ap_ps_peer_uapsd_coex_cmdid;
932 	u32 peer_rate_retry_sched_cmdid;
933 	u32 wlan_profile_trigger_cmdid;
934 	u32 wlan_profile_set_hist_intvl_cmdid;
935 	u32 wlan_profile_get_profile_data_cmdid;
936 	u32 wlan_profile_enable_profile_id_cmdid;
937 	u32 wlan_profile_list_profile_id_cmdid;
938 	u32 pdev_suspend_cmdid;
939 	u32 pdev_resume_cmdid;
940 	u32 add_bcn_filter_cmdid;
941 	u32 rmv_bcn_filter_cmdid;
942 	u32 wow_add_wake_pattern_cmdid;
943 	u32 wow_del_wake_pattern_cmdid;
944 	u32 wow_enable_disable_wake_event_cmdid;
945 	u32 wow_enable_cmdid;
946 	u32 wow_hostwakeup_from_sleep_cmdid;
947 	u32 rtt_measreq_cmdid;
948 	u32 rtt_tsf_cmdid;
949 	u32 vdev_spectral_scan_configure_cmdid;
950 	u32 vdev_spectral_scan_enable_cmdid;
951 	u32 request_stats_cmdid;
952 	u32 request_peer_stats_info_cmdid;
953 	u32 set_arp_ns_offload_cmdid;
954 	u32 network_list_offload_config_cmdid;
955 	u32 gtk_offload_cmdid;
956 	u32 csa_offload_enable_cmdid;
957 	u32 csa_offload_chanswitch_cmdid;
958 	u32 chatter_set_mode_cmdid;
959 	u32 peer_tid_addba_cmdid;
960 	u32 peer_tid_delba_cmdid;
961 	u32 sta_dtim_ps_method_cmdid;
962 	u32 sta_uapsd_auto_trig_cmdid;
963 	u32 sta_keepalive_cmd;
964 	u32 echo_cmdid;
965 	u32 pdev_utf_cmdid;
966 	u32 dbglog_cfg_cmdid;
967 	u32 pdev_qvit_cmdid;
968 	u32 pdev_ftm_intg_cmdid;
969 	u32 vdev_set_keepalive_cmdid;
970 	u32 vdev_get_keepalive_cmdid;
971 	u32 force_fw_hang_cmdid;
972 	u32 gpio_config_cmdid;
973 	u32 gpio_output_cmdid;
974 	u32 pdev_get_temperature_cmdid;
975 	u32 vdev_set_wmm_params_cmdid;
976 	u32 tdls_set_state_cmdid;
977 	u32 tdls_peer_update_cmdid;
978 	u32 adaptive_qcs_cmdid;
979 	u32 scan_update_request_cmdid;
980 	u32 vdev_standby_response_cmdid;
981 	u32 vdev_resume_response_cmdid;
982 	u32 wlan_peer_caching_add_peer_cmdid;
983 	u32 wlan_peer_caching_evict_peer_cmdid;
984 	u32 wlan_peer_caching_restore_peer_cmdid;
985 	u32 wlan_peer_caching_print_all_peers_info_cmdid;
986 	u32 peer_update_wds_entry_cmdid;
987 	u32 peer_add_proxy_sta_entry_cmdid;
988 	u32 rtt_keepalive_cmdid;
989 	u32 oem_req_cmdid;
990 	u32 nan_cmdid;
991 	u32 vdev_ratemask_cmdid;
992 	u32 qboost_cfg_cmdid;
993 	u32 pdev_smart_ant_enable_cmdid;
994 	u32 pdev_smart_ant_set_rx_antenna_cmdid;
995 	u32 peer_smart_ant_set_tx_antenna_cmdid;
996 	u32 peer_smart_ant_set_train_info_cmdid;
997 	u32 peer_smart_ant_set_node_config_ops_cmdid;
998 	u32 pdev_set_antenna_switch_table_cmdid;
999 	u32 pdev_set_ctl_table_cmdid;
1000 	u32 pdev_set_mimogain_table_cmdid;
1001 	u32 pdev_ratepwr_table_cmdid;
1002 	u32 pdev_ratepwr_chainmsk_table_cmdid;
1003 	u32 pdev_fips_cmdid;
1004 	u32 tt_set_conf_cmdid;
1005 	u32 fwtest_cmdid;
1006 	u32 vdev_atf_request_cmdid;
1007 	u32 peer_atf_request_cmdid;
1008 	u32 pdev_get_ani_cck_config_cmdid;
1009 	u32 pdev_get_ani_ofdm_config_cmdid;
1010 	u32 pdev_reserve_ast_entry_cmdid;
1011 	u32 pdev_get_nfcal_power_cmdid;
1012 	u32 pdev_get_tpc_cmdid;
1013 	u32 pdev_get_ast_info_cmdid;
1014 	u32 vdev_set_dscp_tid_map_cmdid;
1015 	u32 pdev_get_info_cmdid;
1016 	u32 vdev_get_info_cmdid;
1017 	u32 vdev_filter_neighbor_rx_packets_cmdid;
1018 	u32 mu_cal_start_cmdid;
1019 	u32 set_cca_params_cmdid;
1020 	u32 pdev_bss_chan_info_request_cmdid;
1021 	u32 pdev_enable_adaptive_cca_cmdid;
1022 	u32 ext_resource_cfg_cmdid;
1023 	u32 vdev_set_ie_cmdid;
1024 	u32 set_lteu_config_cmdid;
1025 	u32 atf_ssid_grouping_request_cmdid;
1026 	u32 peer_atf_ext_request_cmdid;
1027 	u32 set_periodic_channel_stats_cfg_cmdid;
1028 	u32 peer_bwf_request_cmdid;
1029 	u32 btcoex_cfg_cmdid;
1030 	u32 peer_tx_mu_txmit_count_cmdid;
1031 	u32 peer_tx_mu_txmit_rstcnt_cmdid;
1032 	u32 peer_gid_userpos_list_cmdid;
1033 	u32 pdev_check_cal_version_cmdid;
1034 	u32 coex_version_cfg_cmid;
1035 	u32 pdev_get_rx_filter_cmdid;
1036 	u32 pdev_extended_nss_cfg_cmdid;
1037 	u32 vdev_set_scan_nac_rssi_cmdid;
1038 	u32 prog_gpio_band_select_cmdid;
1039 	u32 config_smart_logging_cmdid;
1040 	u32 debug_fatal_condition_cmdid;
1041 	u32 get_tsf_timer_cmdid;
1042 	u32 pdev_get_tpc_table_cmdid;
1043 	u32 vdev_sifs_trigger_time_cmdid;
1044 	u32 pdev_wds_entry_list_cmdid;
1045 	u32 tdls_set_offchan_mode_cmdid;
1046 	u32 radar_found_cmdid;
1047 	u32 set_bb_timing_cmdid;
1048 	u32 per_peer_per_tid_config_cmdid;
1049 };
1050 
1051 /*
1052  * wmi command groups.
1053  */
1054 enum wmi_cmd_group {
1055 	/* 0 to 2 are reserved */
1056 	WMI_GRP_START = 0x3,
1057 	WMI_GRP_SCAN = WMI_GRP_START,
1058 	WMI_GRP_PDEV,
1059 	WMI_GRP_VDEV,
1060 	WMI_GRP_PEER,
1061 	WMI_GRP_MGMT,
1062 	WMI_GRP_BA_NEG,
1063 	WMI_GRP_STA_PS,
1064 	WMI_GRP_DFS,
1065 	WMI_GRP_ROAM,
1066 	WMI_GRP_OFL_SCAN,
1067 	WMI_GRP_P2P,
1068 	WMI_GRP_AP_PS,
1069 	WMI_GRP_RATE_CTRL,
1070 	WMI_GRP_PROFILE,
1071 	WMI_GRP_SUSPEND,
1072 	WMI_GRP_BCN_FILTER,
1073 	WMI_GRP_WOW,
1074 	WMI_GRP_RTT,
1075 	WMI_GRP_SPECTRAL,
1076 	WMI_GRP_STATS,
1077 	WMI_GRP_ARP_NS_OFL,
1078 	WMI_GRP_NLO_OFL,
1079 	WMI_GRP_GTK_OFL,
1080 	WMI_GRP_CSA_OFL,
1081 	WMI_GRP_CHATTER,
1082 	WMI_GRP_TID_ADDBA,
1083 	WMI_GRP_MISC,
1084 	WMI_GRP_GPIO,
1085 };
1086 
1087 #define WMI_CMD_GRP(grp_id) (((grp_id) << 12) | 0x1)
1088 #define WMI_EVT_GRP_START_ID(grp_id) (((grp_id) << 12) | 0x1)
1089 
1090 #define WMI_CMD_UNSUPPORTED 0
1091 
1092 /* Command IDs and command events for MAIN FW. */
1093 enum wmi_cmd_id {
1094 	WMI_INIT_CMDID = 0x1,
1095 
1096 	/* Scan specific commands */
1097 	WMI_START_SCAN_CMDID = WMI_CMD_GRP(WMI_GRP_SCAN),
1098 	WMI_STOP_SCAN_CMDID,
1099 	WMI_SCAN_CHAN_LIST_CMDID,
1100 	WMI_SCAN_SCH_PRIO_TBL_CMDID,
1101 
1102 	/* PDEV (physical device) specific commands */
1103 	WMI_PDEV_SET_REGDOMAIN_CMDID = WMI_CMD_GRP(WMI_GRP_PDEV),
1104 	WMI_PDEV_SET_CHANNEL_CMDID,
1105 	WMI_PDEV_SET_PARAM_CMDID,
1106 	WMI_PDEV_PKTLOG_ENABLE_CMDID,
1107 	WMI_PDEV_PKTLOG_DISABLE_CMDID,
1108 	WMI_PDEV_SET_WMM_PARAMS_CMDID,
1109 	WMI_PDEV_SET_HT_CAP_IE_CMDID,
1110 	WMI_PDEV_SET_VHT_CAP_IE_CMDID,
1111 	WMI_PDEV_SET_DSCP_TID_MAP_CMDID,
1112 	WMI_PDEV_SET_QUIET_MODE_CMDID,
1113 	WMI_PDEV_GREEN_AP_PS_ENABLE_CMDID,
1114 	WMI_PDEV_GET_TPC_CONFIG_CMDID,
1115 	WMI_PDEV_SET_BASE_MACADDR_CMDID,
1116 
1117 	/* VDEV (virtual device) specific commands */
1118 	WMI_VDEV_CREATE_CMDID = WMI_CMD_GRP(WMI_GRP_VDEV),
1119 	WMI_VDEV_DELETE_CMDID,
1120 	WMI_VDEV_START_REQUEST_CMDID,
1121 	WMI_VDEV_RESTART_REQUEST_CMDID,
1122 	WMI_VDEV_UP_CMDID,
1123 	WMI_VDEV_STOP_CMDID,
1124 	WMI_VDEV_DOWN_CMDID,
1125 	WMI_VDEV_SET_PARAM_CMDID,
1126 	WMI_VDEV_INSTALL_KEY_CMDID,
1127 
1128 	/* peer specific commands */
1129 	WMI_PEER_CREATE_CMDID = WMI_CMD_GRP(WMI_GRP_PEER),
1130 	WMI_PEER_DELETE_CMDID,
1131 	WMI_PEER_FLUSH_TIDS_CMDID,
1132 	WMI_PEER_SET_PARAM_CMDID,
1133 	WMI_PEER_ASSOC_CMDID,
1134 	WMI_PEER_ADD_WDS_ENTRY_CMDID,
1135 	WMI_PEER_REMOVE_WDS_ENTRY_CMDID,
1136 	WMI_PEER_MCAST_GROUP_CMDID,
1137 
1138 	/* beacon/management specific commands */
1139 	WMI_BCN_TX_CMDID = WMI_CMD_GRP(WMI_GRP_MGMT),
1140 	WMI_PDEV_SEND_BCN_CMDID,
1141 	WMI_BCN_TMPL_CMDID,
1142 	WMI_BCN_FILTER_RX_CMDID,
1143 	WMI_PRB_REQ_FILTER_RX_CMDID,
1144 	WMI_MGMT_TX_CMDID,
1145 	WMI_PRB_TMPL_CMDID,
1146 
1147 	/* commands to directly control BA negotiation directly from host. */
1148 	WMI_ADDBA_CLEAR_RESP_CMDID = WMI_CMD_GRP(WMI_GRP_BA_NEG),
1149 	WMI_ADDBA_SEND_CMDID,
1150 	WMI_ADDBA_STATUS_CMDID,
1151 	WMI_DELBA_SEND_CMDID,
1152 	WMI_ADDBA_SET_RESP_CMDID,
1153 	WMI_SEND_SINGLEAMSDU_CMDID,
1154 
1155 	/* Station power save specific config */
1156 	WMI_STA_POWERSAVE_MODE_CMDID = WMI_CMD_GRP(WMI_GRP_STA_PS),
1157 	WMI_STA_POWERSAVE_PARAM_CMDID,
1158 	WMI_STA_MIMO_PS_MODE_CMDID,
1159 
1160 	/** DFS-specific commands */
1161 	WMI_PDEV_DFS_ENABLE_CMDID = WMI_CMD_GRP(WMI_GRP_DFS),
1162 	WMI_PDEV_DFS_DISABLE_CMDID,
1163 
1164 	/* Roaming specific  commands */
1165 	WMI_ROAM_SCAN_MODE = WMI_CMD_GRP(WMI_GRP_ROAM),
1166 	WMI_ROAM_SCAN_RSSI_THRESHOLD,
1167 	WMI_ROAM_SCAN_PERIOD,
1168 	WMI_ROAM_SCAN_RSSI_CHANGE_THRESHOLD,
1169 	WMI_ROAM_AP_PROFILE,
1170 
1171 	/* offload scan specific commands */
1172 	WMI_OFL_SCAN_ADD_AP_PROFILE = WMI_CMD_GRP(WMI_GRP_OFL_SCAN),
1173 	WMI_OFL_SCAN_REMOVE_AP_PROFILE,
1174 	WMI_OFL_SCAN_PERIOD,
1175 
1176 	/* P2P specific commands */
1177 	WMI_P2P_DEV_SET_DEVICE_INFO = WMI_CMD_GRP(WMI_GRP_P2P),
1178 	WMI_P2P_DEV_SET_DISCOVERABILITY,
1179 	WMI_P2P_GO_SET_BEACON_IE,
1180 	WMI_P2P_GO_SET_PROBE_RESP_IE,
1181 	WMI_P2P_SET_VENDOR_IE_DATA_CMDID,
1182 
1183 	/* AP power save specific config */
1184 	WMI_AP_PS_PEER_PARAM_CMDID = WMI_CMD_GRP(WMI_GRP_AP_PS),
1185 	WMI_AP_PS_PEER_UAPSD_COEX_CMDID,
1186 
1187 	/* Rate-control specific commands */
1188 	WMI_PEER_RATE_RETRY_SCHED_CMDID =
1189 	WMI_CMD_GRP(WMI_GRP_RATE_CTRL),
1190 
1191 	/* WLAN Profiling commands. */
1192 	WMI_WLAN_PROFILE_TRIGGER_CMDID = WMI_CMD_GRP(WMI_GRP_PROFILE),
1193 	WMI_WLAN_PROFILE_SET_HIST_INTVL_CMDID,
1194 	WMI_WLAN_PROFILE_GET_PROFILE_DATA_CMDID,
1195 	WMI_WLAN_PROFILE_ENABLE_PROFILE_ID_CMDID,
1196 	WMI_WLAN_PROFILE_LIST_PROFILE_ID_CMDID,
1197 
1198 	/* Suspend resume command Ids */
1199 	WMI_PDEV_SUSPEND_CMDID = WMI_CMD_GRP(WMI_GRP_SUSPEND),
1200 	WMI_PDEV_RESUME_CMDID,
1201 
1202 	/* Beacon filter commands */
1203 	WMI_ADD_BCN_FILTER_CMDID = WMI_CMD_GRP(WMI_GRP_BCN_FILTER),
1204 	WMI_RMV_BCN_FILTER_CMDID,
1205 
1206 	/* WOW Specific WMI commands*/
1207 	WMI_WOW_ADD_WAKE_PATTERN_CMDID = WMI_CMD_GRP(WMI_GRP_WOW),
1208 	WMI_WOW_DEL_WAKE_PATTERN_CMDID,
1209 	WMI_WOW_ENABLE_DISABLE_WAKE_EVENT_CMDID,
1210 	WMI_WOW_ENABLE_CMDID,
1211 	WMI_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID,
1212 
1213 	/* RTT measurement related cmd */
1214 	WMI_RTT_MEASREQ_CMDID = WMI_CMD_GRP(WMI_GRP_RTT),
1215 	WMI_RTT_TSF_CMDID,
1216 
1217 	/* spectral scan commands */
1218 	WMI_VDEV_SPECTRAL_SCAN_CONFIGURE_CMDID = WMI_CMD_GRP(WMI_GRP_SPECTRAL),
1219 	WMI_VDEV_SPECTRAL_SCAN_ENABLE_CMDID,
1220 
1221 	/* F/W stats */
1222 	WMI_REQUEST_STATS_CMDID = WMI_CMD_GRP(WMI_GRP_STATS),
1223 
1224 	/* ARP OFFLOAD REQUEST*/
1225 	WMI_SET_ARP_NS_OFFLOAD_CMDID = WMI_CMD_GRP(WMI_GRP_ARP_NS_OFL),
1226 
1227 	/* NS offload confid*/
1228 	WMI_NETWORK_LIST_OFFLOAD_CONFIG_CMDID = WMI_CMD_GRP(WMI_GRP_NLO_OFL),
1229 
1230 	/* GTK offload Specific WMI commands*/
1231 	WMI_GTK_OFFLOAD_CMDID = WMI_CMD_GRP(WMI_GRP_GTK_OFL),
1232 
1233 	/* CSA offload Specific WMI commands*/
1234 	WMI_CSA_OFFLOAD_ENABLE_CMDID = WMI_CMD_GRP(WMI_GRP_CSA_OFL),
1235 	WMI_CSA_OFFLOAD_CHANSWITCH_CMDID,
1236 
1237 	/* Chatter commands*/
1238 	WMI_CHATTER_SET_MODE_CMDID = WMI_CMD_GRP(WMI_GRP_CHATTER),
1239 
1240 	/* addba specific commands */
1241 	WMI_PEER_TID_ADDBA_CMDID = WMI_CMD_GRP(WMI_GRP_TID_ADDBA),
1242 	WMI_PEER_TID_DELBA_CMDID,
1243 
1244 	/* set station mimo powersave method */
1245 	WMI_STA_DTIM_PS_METHOD_CMDID,
1246 	/* Configure the Station UAPSD AC Auto Trigger Parameters */
1247 	WMI_STA_UAPSD_AUTO_TRIG_CMDID,
1248 
1249 	/* STA Keep alive parameter configuration,
1250 	 * Requires WMI_SERVICE_STA_KEEP_ALIVE
1251 	 */
1252 	WMI_STA_KEEPALIVE_CMD,
1253 
1254 	/* misc command group */
1255 	WMI_ECHO_CMDID = WMI_CMD_GRP(WMI_GRP_MISC),
1256 	WMI_PDEV_UTF_CMDID,
1257 	WMI_DBGLOG_CFG_CMDID,
1258 	WMI_PDEV_QVIT_CMDID,
1259 	WMI_PDEV_FTM_INTG_CMDID,
1260 	WMI_VDEV_SET_KEEPALIVE_CMDID,
1261 	WMI_VDEV_GET_KEEPALIVE_CMDID,
1262 	WMI_FORCE_FW_HANG_CMDID,
1263 
1264 	/* GPIO Configuration */
1265 	WMI_GPIO_CONFIG_CMDID = WMI_CMD_GRP(WMI_GRP_GPIO),
1266 	WMI_GPIO_OUTPUT_CMDID,
1267 };
1268 
1269 enum wmi_event_id {
1270 	WMI_SERVICE_READY_EVENTID = 0x1,
1271 	WMI_READY_EVENTID,
1272 	WMI_SERVICE_AVAILABLE_EVENTID,
1273 
1274 	/* Scan specific events */
1275 	WMI_SCAN_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_SCAN),
1276 
1277 	/* PDEV specific events */
1278 	WMI_PDEV_TPC_CONFIG_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_PDEV),
1279 	WMI_CHAN_INFO_EVENTID,
1280 	WMI_PHYERR_EVENTID,
1281 
1282 	/* VDEV specific events */
1283 	WMI_VDEV_START_RESP_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_VDEV),
1284 	WMI_VDEV_STOPPED_EVENTID,
1285 	WMI_VDEV_INSTALL_KEY_COMPLETE_EVENTID,
1286 
1287 	/* peer specific events */
1288 	WMI_PEER_STA_KICKOUT_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_PEER),
1289 
1290 	/* beacon/mgmt specific events */
1291 	WMI_MGMT_RX_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_MGMT),
1292 	WMI_HOST_SWBA_EVENTID,
1293 	WMI_TBTTOFFSET_UPDATE_EVENTID,
1294 
1295 	/* ADDBA Related WMI Events*/
1296 	WMI_TX_DELBA_COMPLETE_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_BA_NEG),
1297 	WMI_TX_ADDBA_COMPLETE_EVENTID,
1298 
1299 	/* Roam event to trigger roaming on host */
1300 	WMI_ROAM_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_ROAM),
1301 	WMI_PROFILE_MATCH,
1302 
1303 	/* WoW */
1304 	WMI_WOW_WAKEUP_HOST_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_WOW),
1305 
1306 	/* RTT */
1307 	WMI_RTT_MEASUREMENT_REPORT_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_RTT),
1308 	WMI_TSF_MEASUREMENT_REPORT_EVENTID,
1309 	WMI_RTT_ERROR_REPORT_EVENTID,
1310 
1311 	/* GTK offload */
1312 	WMI_GTK_OFFLOAD_STATUS_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_GTK_OFL),
1313 	WMI_GTK_REKEY_FAIL_EVENTID,
1314 
1315 	/* CSA IE received event */
1316 	WMI_CSA_HANDLING_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_CSA_OFL),
1317 
1318 	/* Misc events */
1319 	WMI_ECHO_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_MISC),
1320 	WMI_PDEV_UTF_EVENTID,
1321 	WMI_DEBUG_MESG_EVENTID,
1322 	WMI_UPDATE_STATS_EVENTID,
1323 	WMI_DEBUG_PRINT_EVENTID,
1324 	WMI_DCS_INTERFERENCE_EVENTID,
1325 	WMI_PDEV_QVIT_EVENTID,
1326 	WMI_WLAN_PROFILE_DATA_EVENTID,
1327 	WMI_PDEV_FTM_INTG_EVENTID,
1328 	WMI_WLAN_FREQ_AVOID_EVENTID,
1329 	WMI_VDEV_GET_KEEPALIVE_EVENTID,
1330 
1331 	/* GPIO Event */
1332 	WMI_GPIO_INPUT_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_GPIO),
1333 };
1334 
1335 /* Command IDs and command events for 10.X firmware */
1336 enum wmi_10x_cmd_id {
1337 	WMI_10X_START_CMDID = 0x9000,
1338 	WMI_10X_END_CMDID = 0x9FFF,
1339 
1340 	/* initialize the wlan sub system */
1341 	WMI_10X_INIT_CMDID,
1342 
1343 	/* Scan specific commands */
1344 
1345 	WMI_10X_START_SCAN_CMDID = WMI_10X_START_CMDID,
1346 	WMI_10X_STOP_SCAN_CMDID,
1347 	WMI_10X_SCAN_CHAN_LIST_CMDID,
1348 	WMI_10X_ECHO_CMDID,
1349 
1350 	/* PDEV(physical device) specific commands */
1351 	WMI_10X_PDEV_SET_REGDOMAIN_CMDID,
1352 	WMI_10X_PDEV_SET_CHANNEL_CMDID,
1353 	WMI_10X_PDEV_SET_PARAM_CMDID,
1354 	WMI_10X_PDEV_PKTLOG_ENABLE_CMDID,
1355 	WMI_10X_PDEV_PKTLOG_DISABLE_CMDID,
1356 	WMI_10X_PDEV_SET_WMM_PARAMS_CMDID,
1357 	WMI_10X_PDEV_SET_HT_CAP_IE_CMDID,
1358 	WMI_10X_PDEV_SET_VHT_CAP_IE_CMDID,
1359 	WMI_10X_PDEV_SET_BASE_MACADDR_CMDID,
1360 	WMI_10X_PDEV_SET_DSCP_TID_MAP_CMDID,
1361 	WMI_10X_PDEV_SET_QUIET_MODE_CMDID,
1362 	WMI_10X_PDEV_GREEN_AP_PS_ENABLE_CMDID,
1363 	WMI_10X_PDEV_GET_TPC_CONFIG_CMDID,
1364 
1365 	/* VDEV(virtual device) specific commands */
1366 	WMI_10X_VDEV_CREATE_CMDID,
1367 	WMI_10X_VDEV_DELETE_CMDID,
1368 	WMI_10X_VDEV_START_REQUEST_CMDID,
1369 	WMI_10X_VDEV_RESTART_REQUEST_CMDID,
1370 	WMI_10X_VDEV_UP_CMDID,
1371 	WMI_10X_VDEV_STOP_CMDID,
1372 	WMI_10X_VDEV_DOWN_CMDID,
1373 	WMI_10X_VDEV_STANDBY_RESPONSE_CMDID,
1374 	WMI_10X_VDEV_RESUME_RESPONSE_CMDID,
1375 	WMI_10X_VDEV_SET_PARAM_CMDID,
1376 	WMI_10X_VDEV_INSTALL_KEY_CMDID,
1377 
1378 	/* peer specific commands */
1379 	WMI_10X_PEER_CREATE_CMDID,
1380 	WMI_10X_PEER_DELETE_CMDID,
1381 	WMI_10X_PEER_FLUSH_TIDS_CMDID,
1382 	WMI_10X_PEER_SET_PARAM_CMDID,
1383 	WMI_10X_PEER_ASSOC_CMDID,
1384 	WMI_10X_PEER_ADD_WDS_ENTRY_CMDID,
1385 	WMI_10X_PEER_REMOVE_WDS_ENTRY_CMDID,
1386 	WMI_10X_PEER_MCAST_GROUP_CMDID,
1387 
1388 	/* beacon/management specific commands */
1389 
1390 	WMI_10X_BCN_TX_CMDID,
1391 	WMI_10X_BCN_PRB_TMPL_CMDID,
1392 	WMI_10X_BCN_FILTER_RX_CMDID,
1393 	WMI_10X_PRB_REQ_FILTER_RX_CMDID,
1394 	WMI_10X_MGMT_TX_CMDID,
1395 
1396 	/* commands to directly control ba negotiation directly from host. */
1397 	WMI_10X_ADDBA_CLEAR_RESP_CMDID,
1398 	WMI_10X_ADDBA_SEND_CMDID,
1399 	WMI_10X_ADDBA_STATUS_CMDID,
1400 	WMI_10X_DELBA_SEND_CMDID,
1401 	WMI_10X_ADDBA_SET_RESP_CMDID,
1402 	WMI_10X_SEND_SINGLEAMSDU_CMDID,
1403 
1404 	/* Station power save specific config */
1405 	WMI_10X_STA_POWERSAVE_MODE_CMDID,
1406 	WMI_10X_STA_POWERSAVE_PARAM_CMDID,
1407 	WMI_10X_STA_MIMO_PS_MODE_CMDID,
1408 
1409 	/* set debug log config */
1410 	WMI_10X_DBGLOG_CFG_CMDID,
1411 
1412 	/* DFS-specific commands */
1413 	WMI_10X_PDEV_DFS_ENABLE_CMDID,
1414 	WMI_10X_PDEV_DFS_DISABLE_CMDID,
1415 
1416 	/* QVIT specific command id */
1417 	WMI_10X_PDEV_QVIT_CMDID,
1418 
1419 	/* Offload Scan and Roaming related  commands */
1420 	WMI_10X_ROAM_SCAN_MODE,
1421 	WMI_10X_ROAM_SCAN_RSSI_THRESHOLD,
1422 	WMI_10X_ROAM_SCAN_PERIOD,
1423 	WMI_10X_ROAM_SCAN_RSSI_CHANGE_THRESHOLD,
1424 	WMI_10X_ROAM_AP_PROFILE,
1425 	WMI_10X_OFL_SCAN_ADD_AP_PROFILE,
1426 	WMI_10X_OFL_SCAN_REMOVE_AP_PROFILE,
1427 	WMI_10X_OFL_SCAN_PERIOD,
1428 
1429 	/* P2P specific commands */
1430 	WMI_10X_P2P_DEV_SET_DEVICE_INFO,
1431 	WMI_10X_P2P_DEV_SET_DISCOVERABILITY,
1432 	WMI_10X_P2P_GO_SET_BEACON_IE,
1433 	WMI_10X_P2P_GO_SET_PROBE_RESP_IE,
1434 
1435 	/* AP power save specific config */
1436 	WMI_10X_AP_PS_PEER_PARAM_CMDID,
1437 	WMI_10X_AP_PS_PEER_UAPSD_COEX_CMDID,
1438 
1439 	/* Rate-control specific commands */
1440 	WMI_10X_PEER_RATE_RETRY_SCHED_CMDID,
1441 
1442 	/* WLAN Profiling commands. */
1443 	WMI_10X_WLAN_PROFILE_TRIGGER_CMDID,
1444 	WMI_10X_WLAN_PROFILE_SET_HIST_INTVL_CMDID,
1445 	WMI_10X_WLAN_PROFILE_GET_PROFILE_DATA_CMDID,
1446 	WMI_10X_WLAN_PROFILE_ENABLE_PROFILE_ID_CMDID,
1447 	WMI_10X_WLAN_PROFILE_LIST_PROFILE_ID_CMDID,
1448 
1449 	/* Suspend resume command Ids */
1450 	WMI_10X_PDEV_SUSPEND_CMDID,
1451 	WMI_10X_PDEV_RESUME_CMDID,
1452 
1453 	/* Beacon filter commands */
1454 	WMI_10X_ADD_BCN_FILTER_CMDID,
1455 	WMI_10X_RMV_BCN_FILTER_CMDID,
1456 
1457 	/* WOW Specific WMI commands*/
1458 	WMI_10X_WOW_ADD_WAKE_PATTERN_CMDID,
1459 	WMI_10X_WOW_DEL_WAKE_PATTERN_CMDID,
1460 	WMI_10X_WOW_ENABLE_DISABLE_WAKE_EVENT_CMDID,
1461 	WMI_10X_WOW_ENABLE_CMDID,
1462 	WMI_10X_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID,
1463 
1464 	/* RTT measurement related cmd */
1465 	WMI_10X_RTT_MEASREQ_CMDID,
1466 	WMI_10X_RTT_TSF_CMDID,
1467 
1468 	/* transmit beacon by value */
1469 	WMI_10X_PDEV_SEND_BCN_CMDID,
1470 
1471 	/* F/W stats */
1472 	WMI_10X_VDEV_SPECTRAL_SCAN_CONFIGURE_CMDID,
1473 	WMI_10X_VDEV_SPECTRAL_SCAN_ENABLE_CMDID,
1474 	WMI_10X_REQUEST_STATS_CMDID,
1475 
1476 	/* GPIO Configuration */
1477 	WMI_10X_GPIO_CONFIG_CMDID,
1478 	WMI_10X_GPIO_OUTPUT_CMDID,
1479 
1480 	WMI_10X_PDEV_UTF_CMDID = WMI_10X_END_CMDID - 1,
1481 };
1482 
1483 enum wmi_10x_event_id {
1484 	WMI_10X_SERVICE_READY_EVENTID = 0x8000,
1485 	WMI_10X_READY_EVENTID,
1486 	WMI_10X_START_EVENTID = 0x9000,
1487 	WMI_10X_END_EVENTID = 0x9FFF,
1488 
1489 	/* Scan specific events */
1490 	WMI_10X_SCAN_EVENTID = WMI_10X_START_EVENTID,
1491 	WMI_10X_ECHO_EVENTID,
1492 	WMI_10X_DEBUG_MESG_EVENTID,
1493 	WMI_10X_UPDATE_STATS_EVENTID,
1494 
1495 	/* Instantaneous RSSI event */
1496 	WMI_10X_INST_RSSI_STATS_EVENTID,
1497 
1498 	/* VDEV specific events */
1499 	WMI_10X_VDEV_START_RESP_EVENTID,
1500 	WMI_10X_VDEV_STANDBY_REQ_EVENTID,
1501 	WMI_10X_VDEV_RESUME_REQ_EVENTID,
1502 	WMI_10X_VDEV_STOPPED_EVENTID,
1503 
1504 	/* peer  specific events */
1505 	WMI_10X_PEER_STA_KICKOUT_EVENTID,
1506 
1507 	/* beacon/mgmt specific events */
1508 	WMI_10X_HOST_SWBA_EVENTID,
1509 	WMI_10X_TBTTOFFSET_UPDATE_EVENTID,
1510 	WMI_10X_MGMT_RX_EVENTID,
1511 
1512 	/* Channel stats event */
1513 	WMI_10X_CHAN_INFO_EVENTID,
1514 
1515 	/* PHY Error specific WMI event */
1516 	WMI_10X_PHYERR_EVENTID,
1517 
1518 	/* Roam event to trigger roaming on host */
1519 	WMI_10X_ROAM_EVENTID,
1520 
1521 	/* matching AP found from list of profiles */
1522 	WMI_10X_PROFILE_MATCH,
1523 
1524 	/* debug print message used for tracing FW code while debugging */
1525 	WMI_10X_DEBUG_PRINT_EVENTID,
1526 	/* VI spoecific event */
1527 	WMI_10X_PDEV_QVIT_EVENTID,
1528 	/* FW code profile data in response to profile request */
1529 	WMI_10X_WLAN_PROFILE_DATA_EVENTID,
1530 
1531 	/*RTT related event ID*/
1532 	WMI_10X_RTT_MEASUREMENT_REPORT_EVENTID,
1533 	WMI_10X_TSF_MEASUREMENT_REPORT_EVENTID,
1534 	WMI_10X_RTT_ERROR_REPORT_EVENTID,
1535 
1536 	WMI_10X_WOW_WAKEUP_HOST_EVENTID,
1537 	WMI_10X_DCS_INTERFERENCE_EVENTID,
1538 
1539 	/* TPC config for the current operating channel */
1540 	WMI_10X_PDEV_TPC_CONFIG_EVENTID,
1541 
1542 	WMI_10X_GPIO_INPUT_EVENTID,
1543 	WMI_10X_PDEV_UTF_EVENTID = WMI_10X_END_EVENTID - 1,
1544 };
1545 
1546 enum wmi_10_2_cmd_id {
1547 	WMI_10_2_START_CMDID = 0x9000,
1548 	WMI_10_2_END_CMDID = 0x9FFF,
1549 	WMI_10_2_INIT_CMDID,
1550 	WMI_10_2_START_SCAN_CMDID = WMI_10_2_START_CMDID,
1551 	WMI_10_2_STOP_SCAN_CMDID,
1552 	WMI_10_2_SCAN_CHAN_LIST_CMDID,
1553 	WMI_10_2_ECHO_CMDID,
1554 	WMI_10_2_PDEV_SET_REGDOMAIN_CMDID,
1555 	WMI_10_2_PDEV_SET_CHANNEL_CMDID,
1556 	WMI_10_2_PDEV_SET_PARAM_CMDID,
1557 	WMI_10_2_PDEV_PKTLOG_ENABLE_CMDID,
1558 	WMI_10_2_PDEV_PKTLOG_DISABLE_CMDID,
1559 	WMI_10_2_PDEV_SET_WMM_PARAMS_CMDID,
1560 	WMI_10_2_PDEV_SET_HT_CAP_IE_CMDID,
1561 	WMI_10_2_PDEV_SET_VHT_CAP_IE_CMDID,
1562 	WMI_10_2_PDEV_SET_BASE_MACADDR_CMDID,
1563 	WMI_10_2_PDEV_SET_QUIET_MODE_CMDID,
1564 	WMI_10_2_PDEV_GREEN_AP_PS_ENABLE_CMDID,
1565 	WMI_10_2_PDEV_GET_TPC_CONFIG_CMDID,
1566 	WMI_10_2_VDEV_CREATE_CMDID,
1567 	WMI_10_2_VDEV_DELETE_CMDID,
1568 	WMI_10_2_VDEV_START_REQUEST_CMDID,
1569 	WMI_10_2_VDEV_RESTART_REQUEST_CMDID,
1570 	WMI_10_2_VDEV_UP_CMDID,
1571 	WMI_10_2_VDEV_STOP_CMDID,
1572 	WMI_10_2_VDEV_DOWN_CMDID,
1573 	WMI_10_2_VDEV_STANDBY_RESPONSE_CMDID,
1574 	WMI_10_2_VDEV_RESUME_RESPONSE_CMDID,
1575 	WMI_10_2_VDEV_SET_PARAM_CMDID,
1576 	WMI_10_2_VDEV_INSTALL_KEY_CMDID,
1577 	WMI_10_2_VDEV_SET_DSCP_TID_MAP_CMDID,
1578 	WMI_10_2_PEER_CREATE_CMDID,
1579 	WMI_10_2_PEER_DELETE_CMDID,
1580 	WMI_10_2_PEER_FLUSH_TIDS_CMDID,
1581 	WMI_10_2_PEER_SET_PARAM_CMDID,
1582 	WMI_10_2_PEER_ASSOC_CMDID,
1583 	WMI_10_2_PEER_ADD_WDS_ENTRY_CMDID,
1584 	WMI_10_2_PEER_UPDATE_WDS_ENTRY_CMDID,
1585 	WMI_10_2_PEER_REMOVE_WDS_ENTRY_CMDID,
1586 	WMI_10_2_PEER_MCAST_GROUP_CMDID,
1587 	WMI_10_2_BCN_TX_CMDID,
1588 	WMI_10_2_BCN_PRB_TMPL_CMDID,
1589 	WMI_10_2_BCN_FILTER_RX_CMDID,
1590 	WMI_10_2_PRB_REQ_FILTER_RX_CMDID,
1591 	WMI_10_2_MGMT_TX_CMDID,
1592 	WMI_10_2_ADDBA_CLEAR_RESP_CMDID,
1593 	WMI_10_2_ADDBA_SEND_CMDID,
1594 	WMI_10_2_ADDBA_STATUS_CMDID,
1595 	WMI_10_2_DELBA_SEND_CMDID,
1596 	WMI_10_2_ADDBA_SET_RESP_CMDID,
1597 	WMI_10_2_SEND_SINGLEAMSDU_CMDID,
1598 	WMI_10_2_STA_POWERSAVE_MODE_CMDID,
1599 	WMI_10_2_STA_POWERSAVE_PARAM_CMDID,
1600 	WMI_10_2_STA_MIMO_PS_MODE_CMDID,
1601 	WMI_10_2_DBGLOG_CFG_CMDID,
1602 	WMI_10_2_PDEV_DFS_ENABLE_CMDID,
1603 	WMI_10_2_PDEV_DFS_DISABLE_CMDID,
1604 	WMI_10_2_PDEV_QVIT_CMDID,
1605 	WMI_10_2_ROAM_SCAN_MODE,
1606 	WMI_10_2_ROAM_SCAN_RSSI_THRESHOLD,
1607 	WMI_10_2_ROAM_SCAN_PERIOD,
1608 	WMI_10_2_ROAM_SCAN_RSSI_CHANGE_THRESHOLD,
1609 	WMI_10_2_ROAM_AP_PROFILE,
1610 	WMI_10_2_OFL_SCAN_ADD_AP_PROFILE,
1611 	WMI_10_2_OFL_SCAN_REMOVE_AP_PROFILE,
1612 	WMI_10_2_OFL_SCAN_PERIOD,
1613 	WMI_10_2_P2P_DEV_SET_DEVICE_INFO,
1614 	WMI_10_2_P2P_DEV_SET_DISCOVERABILITY,
1615 	WMI_10_2_P2P_GO_SET_BEACON_IE,
1616 	WMI_10_2_P2P_GO_SET_PROBE_RESP_IE,
1617 	WMI_10_2_AP_PS_PEER_PARAM_CMDID,
1618 	WMI_10_2_AP_PS_PEER_UAPSD_COEX_CMDID,
1619 	WMI_10_2_PEER_RATE_RETRY_SCHED_CMDID,
1620 	WMI_10_2_WLAN_PROFILE_TRIGGER_CMDID,
1621 	WMI_10_2_WLAN_PROFILE_SET_HIST_INTVL_CMDID,
1622 	WMI_10_2_WLAN_PROFILE_GET_PROFILE_DATA_CMDID,
1623 	WMI_10_2_WLAN_PROFILE_ENABLE_PROFILE_ID_CMDID,
1624 	WMI_10_2_WLAN_PROFILE_LIST_PROFILE_ID_CMDID,
1625 	WMI_10_2_PDEV_SUSPEND_CMDID,
1626 	WMI_10_2_PDEV_RESUME_CMDID,
1627 	WMI_10_2_ADD_BCN_FILTER_CMDID,
1628 	WMI_10_2_RMV_BCN_FILTER_CMDID,
1629 	WMI_10_2_WOW_ADD_WAKE_PATTERN_CMDID,
1630 	WMI_10_2_WOW_DEL_WAKE_PATTERN_CMDID,
1631 	WMI_10_2_WOW_ENABLE_DISABLE_WAKE_EVENT_CMDID,
1632 	WMI_10_2_WOW_ENABLE_CMDID,
1633 	WMI_10_2_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID,
1634 	WMI_10_2_RTT_MEASREQ_CMDID,
1635 	WMI_10_2_RTT_TSF_CMDID,
1636 	WMI_10_2_RTT_KEEPALIVE_CMDID,
1637 	WMI_10_2_PDEV_SEND_BCN_CMDID,
1638 	WMI_10_2_VDEV_SPECTRAL_SCAN_CONFIGURE_CMDID,
1639 	WMI_10_2_VDEV_SPECTRAL_SCAN_ENABLE_CMDID,
1640 	WMI_10_2_REQUEST_STATS_CMDID,
1641 	WMI_10_2_GPIO_CONFIG_CMDID,
1642 	WMI_10_2_GPIO_OUTPUT_CMDID,
1643 	WMI_10_2_VDEV_RATEMASK_CMDID,
1644 	WMI_10_2_PDEV_SMART_ANT_ENABLE_CMDID,
1645 	WMI_10_2_PDEV_SMART_ANT_SET_RX_ANTENNA_CMDID,
1646 	WMI_10_2_PEER_SMART_ANT_SET_TX_ANTENNA_CMDID,
1647 	WMI_10_2_PEER_SMART_ANT_SET_TRAIN_INFO_CMDID,
1648 	WMI_10_2_PEER_SMART_ANT_SET_NODE_CONFIG_OPS_CMDID,
1649 	WMI_10_2_FORCE_FW_HANG_CMDID,
1650 	WMI_10_2_PDEV_SET_ANTENNA_SWITCH_TABLE_CMDID,
1651 	WMI_10_2_PDEV_SET_CTL_TABLE_CMDID,
1652 	WMI_10_2_PDEV_SET_MIMOGAIN_TABLE_CMDID,
1653 	WMI_10_2_PDEV_RATEPWR_TABLE_CMDID,
1654 	WMI_10_2_PDEV_RATEPWR_CHAINMSK_TABLE_CMDID,
1655 	WMI_10_2_PDEV_GET_INFO,
1656 	WMI_10_2_VDEV_GET_INFO,
1657 	WMI_10_2_VDEV_ATF_REQUEST_CMDID,
1658 	WMI_10_2_PEER_ATF_REQUEST_CMDID,
1659 	WMI_10_2_PDEV_GET_TEMPERATURE_CMDID,
1660 	WMI_10_2_MU_CAL_START_CMDID,
1661 	WMI_10_2_SET_LTEU_CONFIG_CMDID,
1662 	WMI_10_2_SET_CCA_PARAMS,
1663 	WMI_10_2_PDEV_BSS_CHAN_INFO_REQUEST_CMDID,
1664 	WMI_10_2_FWTEST_CMDID,
1665 	WMI_10_2_PDEV_SET_BB_TIMING_CONFIG_CMDID,
1666 	WMI_10_2_PDEV_UTF_CMDID = WMI_10_2_END_CMDID - 1,
1667 };
1668 
1669 enum wmi_10_2_event_id {
1670 	WMI_10_2_SERVICE_READY_EVENTID = 0x8000,
1671 	WMI_10_2_READY_EVENTID,
1672 	WMI_10_2_DEBUG_MESG_EVENTID,
1673 	WMI_10_2_START_EVENTID = 0x9000,
1674 	WMI_10_2_END_EVENTID = 0x9FFF,
1675 	WMI_10_2_SCAN_EVENTID = WMI_10_2_START_EVENTID,
1676 	WMI_10_2_ECHO_EVENTID,
1677 	WMI_10_2_UPDATE_STATS_EVENTID,
1678 	WMI_10_2_INST_RSSI_STATS_EVENTID,
1679 	WMI_10_2_VDEV_START_RESP_EVENTID,
1680 	WMI_10_2_VDEV_STANDBY_REQ_EVENTID,
1681 	WMI_10_2_VDEV_RESUME_REQ_EVENTID,
1682 	WMI_10_2_VDEV_STOPPED_EVENTID,
1683 	WMI_10_2_PEER_STA_KICKOUT_EVENTID,
1684 	WMI_10_2_HOST_SWBA_EVENTID,
1685 	WMI_10_2_TBTTOFFSET_UPDATE_EVENTID,
1686 	WMI_10_2_MGMT_RX_EVENTID,
1687 	WMI_10_2_CHAN_INFO_EVENTID,
1688 	WMI_10_2_PHYERR_EVENTID,
1689 	WMI_10_2_ROAM_EVENTID,
1690 	WMI_10_2_PROFILE_MATCH,
1691 	WMI_10_2_DEBUG_PRINT_EVENTID,
1692 	WMI_10_2_PDEV_QVIT_EVENTID,
1693 	WMI_10_2_WLAN_PROFILE_DATA_EVENTID,
1694 	WMI_10_2_RTT_MEASUREMENT_REPORT_EVENTID,
1695 	WMI_10_2_TSF_MEASUREMENT_REPORT_EVENTID,
1696 	WMI_10_2_RTT_ERROR_REPORT_EVENTID,
1697 	WMI_10_2_RTT_KEEPALIVE_EVENTID,
1698 	WMI_10_2_WOW_WAKEUP_HOST_EVENTID,
1699 	WMI_10_2_DCS_INTERFERENCE_EVENTID,
1700 	WMI_10_2_PDEV_TPC_CONFIG_EVENTID,
1701 	WMI_10_2_GPIO_INPUT_EVENTID,
1702 	WMI_10_2_PEER_RATECODE_LIST_EVENTID,
1703 	WMI_10_2_GENERIC_BUFFER_EVENTID,
1704 	WMI_10_2_MCAST_BUF_RELEASE_EVENTID,
1705 	WMI_10_2_MCAST_LIST_AGEOUT_EVENTID,
1706 	WMI_10_2_WDS_PEER_EVENTID,
1707 	WMI_10_2_PEER_STA_PS_STATECHG_EVENTID,
1708 	WMI_10_2_PDEV_TEMPERATURE_EVENTID,
1709 	WMI_10_2_MU_REPORT_EVENTID,
1710 	WMI_10_2_PDEV_BSS_CHAN_INFO_EVENTID,
1711 	WMI_10_2_PDEV_UTF_EVENTID = WMI_10_2_END_EVENTID - 1,
1712 };
1713 
1714 enum wmi_10_4_cmd_id {
1715 	WMI_10_4_START_CMDID = 0x9000,
1716 	WMI_10_4_END_CMDID = 0x9FFF,
1717 	WMI_10_4_INIT_CMDID,
1718 	WMI_10_4_START_SCAN_CMDID = WMI_10_4_START_CMDID,
1719 	WMI_10_4_STOP_SCAN_CMDID,
1720 	WMI_10_4_SCAN_CHAN_LIST_CMDID,
1721 	WMI_10_4_SCAN_SCH_PRIO_TBL_CMDID,
1722 	WMI_10_4_SCAN_UPDATE_REQUEST_CMDID,
1723 	WMI_10_4_ECHO_CMDID,
1724 	WMI_10_4_PDEV_SET_REGDOMAIN_CMDID,
1725 	WMI_10_4_PDEV_SET_CHANNEL_CMDID,
1726 	WMI_10_4_PDEV_SET_PARAM_CMDID,
1727 	WMI_10_4_PDEV_PKTLOG_ENABLE_CMDID,
1728 	WMI_10_4_PDEV_PKTLOG_DISABLE_CMDID,
1729 	WMI_10_4_PDEV_SET_WMM_PARAMS_CMDID,
1730 	WMI_10_4_PDEV_SET_HT_CAP_IE_CMDID,
1731 	WMI_10_4_PDEV_SET_VHT_CAP_IE_CMDID,
1732 	WMI_10_4_PDEV_SET_BASE_MACADDR_CMDID,
1733 	WMI_10_4_PDEV_SET_DSCP_TID_MAP_CMDID,
1734 	WMI_10_4_PDEV_SET_QUIET_MODE_CMDID,
1735 	WMI_10_4_PDEV_GREEN_AP_PS_ENABLE_CMDID,
1736 	WMI_10_4_PDEV_GET_TPC_CONFIG_CMDID,
1737 	WMI_10_4_VDEV_CREATE_CMDID,
1738 	WMI_10_4_VDEV_DELETE_CMDID,
1739 	WMI_10_4_VDEV_START_REQUEST_CMDID,
1740 	WMI_10_4_VDEV_RESTART_REQUEST_CMDID,
1741 	WMI_10_4_VDEV_UP_CMDID,
1742 	WMI_10_4_VDEV_STOP_CMDID,
1743 	WMI_10_4_VDEV_DOWN_CMDID,
1744 	WMI_10_4_VDEV_STANDBY_RESPONSE_CMDID,
1745 	WMI_10_4_VDEV_RESUME_RESPONSE_CMDID,
1746 	WMI_10_4_VDEV_SET_PARAM_CMDID,
1747 	WMI_10_4_VDEV_INSTALL_KEY_CMDID,
1748 	WMI_10_4_WLAN_PEER_CACHING_ADD_PEER_CMDID,
1749 	WMI_10_4_WLAN_PEER_CACHING_EVICT_PEER_CMDID,
1750 	WMI_10_4_WLAN_PEER_CACHING_RESTORE_PEER_CMDID,
1751 	WMI_10_4_WLAN_PEER_CACHING_PRINT_ALL_PEERS_INFO_CMDID,
1752 	WMI_10_4_PEER_CREATE_CMDID,
1753 	WMI_10_4_PEER_DELETE_CMDID,
1754 	WMI_10_4_PEER_FLUSH_TIDS_CMDID,
1755 	WMI_10_4_PEER_SET_PARAM_CMDID,
1756 	WMI_10_4_PEER_ASSOC_CMDID,
1757 	WMI_10_4_PEER_ADD_WDS_ENTRY_CMDID,
1758 	WMI_10_4_PEER_UPDATE_WDS_ENTRY_CMDID,
1759 	WMI_10_4_PEER_REMOVE_WDS_ENTRY_CMDID,
1760 	WMI_10_4_PEER_ADD_PROXY_STA_ENTRY_CMDID,
1761 	WMI_10_4_PEER_MCAST_GROUP_CMDID,
1762 	WMI_10_4_BCN_TX_CMDID,
1763 	WMI_10_4_PDEV_SEND_BCN_CMDID,
1764 	WMI_10_4_BCN_PRB_TMPL_CMDID,
1765 	WMI_10_4_BCN_FILTER_RX_CMDID,
1766 	WMI_10_4_PRB_REQ_FILTER_RX_CMDID,
1767 	WMI_10_4_MGMT_TX_CMDID,
1768 	WMI_10_4_PRB_TMPL_CMDID,
1769 	WMI_10_4_ADDBA_CLEAR_RESP_CMDID,
1770 	WMI_10_4_ADDBA_SEND_CMDID,
1771 	WMI_10_4_ADDBA_STATUS_CMDID,
1772 	WMI_10_4_DELBA_SEND_CMDID,
1773 	WMI_10_4_ADDBA_SET_RESP_CMDID,
1774 	WMI_10_4_SEND_SINGLEAMSDU_CMDID,
1775 	WMI_10_4_STA_POWERSAVE_MODE_CMDID,
1776 	WMI_10_4_STA_POWERSAVE_PARAM_CMDID,
1777 	WMI_10_4_STA_MIMO_PS_MODE_CMDID,
1778 	WMI_10_4_DBGLOG_CFG_CMDID,
1779 	WMI_10_4_PDEV_DFS_ENABLE_CMDID,
1780 	WMI_10_4_PDEV_DFS_DISABLE_CMDID,
1781 	WMI_10_4_PDEV_QVIT_CMDID,
1782 	WMI_10_4_ROAM_SCAN_MODE,
1783 	WMI_10_4_ROAM_SCAN_RSSI_THRESHOLD,
1784 	WMI_10_4_ROAM_SCAN_PERIOD,
1785 	WMI_10_4_ROAM_SCAN_RSSI_CHANGE_THRESHOLD,
1786 	WMI_10_4_ROAM_AP_PROFILE,
1787 	WMI_10_4_OFL_SCAN_ADD_AP_PROFILE,
1788 	WMI_10_4_OFL_SCAN_REMOVE_AP_PROFILE,
1789 	WMI_10_4_OFL_SCAN_PERIOD,
1790 	WMI_10_4_P2P_DEV_SET_DEVICE_INFO,
1791 	WMI_10_4_P2P_DEV_SET_DISCOVERABILITY,
1792 	WMI_10_4_P2P_GO_SET_BEACON_IE,
1793 	WMI_10_4_P2P_GO_SET_PROBE_RESP_IE,
1794 	WMI_10_4_P2P_SET_VENDOR_IE_DATA_CMDID,
1795 	WMI_10_4_AP_PS_PEER_PARAM_CMDID,
1796 	WMI_10_4_AP_PS_PEER_UAPSD_COEX_CMDID,
1797 	WMI_10_4_PEER_RATE_RETRY_SCHED_CMDID,
1798 	WMI_10_4_WLAN_PROFILE_TRIGGER_CMDID,
1799 	WMI_10_4_WLAN_PROFILE_SET_HIST_INTVL_CMDID,
1800 	WMI_10_4_WLAN_PROFILE_GET_PROFILE_DATA_CMDID,
1801 	WMI_10_4_WLAN_PROFILE_ENABLE_PROFILE_ID_CMDID,
1802 	WMI_10_4_WLAN_PROFILE_LIST_PROFILE_ID_CMDID,
1803 	WMI_10_4_PDEV_SUSPEND_CMDID,
1804 	WMI_10_4_PDEV_RESUME_CMDID,
1805 	WMI_10_4_ADD_BCN_FILTER_CMDID,
1806 	WMI_10_4_RMV_BCN_FILTER_CMDID,
1807 	WMI_10_4_WOW_ADD_WAKE_PATTERN_CMDID,
1808 	WMI_10_4_WOW_DEL_WAKE_PATTERN_CMDID,
1809 	WMI_10_4_WOW_ENABLE_DISABLE_WAKE_EVENT_CMDID,
1810 	WMI_10_4_WOW_ENABLE_CMDID,
1811 	WMI_10_4_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID,
1812 	WMI_10_4_RTT_MEASREQ_CMDID,
1813 	WMI_10_4_RTT_TSF_CMDID,
1814 	WMI_10_4_RTT_KEEPALIVE_CMDID,
1815 	WMI_10_4_OEM_REQ_CMDID,
1816 	WMI_10_4_NAN_CMDID,
1817 	WMI_10_4_VDEV_SPECTRAL_SCAN_CONFIGURE_CMDID,
1818 	WMI_10_4_VDEV_SPECTRAL_SCAN_ENABLE_CMDID,
1819 	WMI_10_4_REQUEST_STATS_CMDID,
1820 	WMI_10_4_GPIO_CONFIG_CMDID,
1821 	WMI_10_4_GPIO_OUTPUT_CMDID,
1822 	WMI_10_4_VDEV_RATEMASK_CMDID,
1823 	WMI_10_4_CSA_OFFLOAD_ENABLE_CMDID,
1824 	WMI_10_4_GTK_OFFLOAD_CMDID,
1825 	WMI_10_4_QBOOST_CFG_CMDID,
1826 	WMI_10_4_CSA_OFFLOAD_CHANSWITCH_CMDID,
1827 	WMI_10_4_PDEV_SMART_ANT_ENABLE_CMDID,
1828 	WMI_10_4_PDEV_SMART_ANT_SET_RX_ANTENNA_CMDID,
1829 	WMI_10_4_PEER_SMART_ANT_SET_TX_ANTENNA_CMDID,
1830 	WMI_10_4_PEER_SMART_ANT_SET_TRAIN_INFO_CMDID,
1831 	WMI_10_4_PEER_SMART_ANT_SET_NODE_CONFIG_OPS_CMDID,
1832 	WMI_10_4_VDEV_SET_KEEPALIVE_CMDID,
1833 	WMI_10_4_VDEV_GET_KEEPALIVE_CMDID,
1834 	WMI_10_4_FORCE_FW_HANG_CMDID,
1835 	WMI_10_4_PDEV_SET_ANTENNA_SWITCH_TABLE_CMDID,
1836 	WMI_10_4_PDEV_SET_CTL_TABLE_CMDID,
1837 	WMI_10_4_PDEV_SET_MIMOGAIN_TABLE_CMDID,
1838 	WMI_10_4_PDEV_RATEPWR_TABLE_CMDID,
1839 	WMI_10_4_PDEV_RATEPWR_CHAINMSK_TABLE_CMDID,
1840 	WMI_10_4_PDEV_FIPS_CMDID,
1841 	WMI_10_4_TT_SET_CONF_CMDID,
1842 	WMI_10_4_FWTEST_CMDID,
1843 	WMI_10_4_VDEV_ATF_REQUEST_CMDID,
1844 	WMI_10_4_PEER_ATF_REQUEST_CMDID,
1845 	WMI_10_4_PDEV_GET_ANI_CCK_CONFIG_CMDID,
1846 	WMI_10_4_PDEV_GET_ANI_OFDM_CONFIG_CMDID,
1847 	WMI_10_4_PDEV_RESERVE_AST_ENTRY_CMDID,
1848 	WMI_10_4_PDEV_GET_NFCAL_POWER_CMDID,
1849 	WMI_10_4_PDEV_GET_TPC_CMDID,
1850 	WMI_10_4_PDEV_GET_AST_INFO_CMDID,
1851 	WMI_10_4_VDEV_SET_DSCP_TID_MAP_CMDID,
1852 	WMI_10_4_PDEV_GET_TEMPERATURE_CMDID,
1853 	WMI_10_4_PDEV_GET_INFO_CMDID,
1854 	WMI_10_4_VDEV_GET_INFO_CMDID,
1855 	WMI_10_4_VDEV_FILTER_NEIGHBOR_RX_PACKETS_CMDID,
1856 	WMI_10_4_MU_CAL_START_CMDID,
1857 	WMI_10_4_SET_CCA_PARAMS_CMDID,
1858 	WMI_10_4_PDEV_BSS_CHAN_INFO_REQUEST_CMDID,
1859 	WMI_10_4_EXT_RESOURCE_CFG_CMDID,
1860 	WMI_10_4_VDEV_SET_IE_CMDID,
1861 	WMI_10_4_SET_LTEU_CONFIG_CMDID,
1862 	WMI_10_4_ATF_SSID_GROUPING_REQUEST_CMDID,
1863 	WMI_10_4_PEER_ATF_EXT_REQUEST_CMDID,
1864 	WMI_10_4_SET_PERIODIC_CHANNEL_STATS_CONFIG,
1865 	WMI_10_4_PEER_BWF_REQUEST_CMDID,
1866 	WMI_10_4_BTCOEX_CFG_CMDID,
1867 	WMI_10_4_PEER_TX_MU_TXMIT_COUNT_CMDID,
1868 	WMI_10_4_PEER_TX_MU_TXMIT_RSTCNT_CMDID,
1869 	WMI_10_4_PEER_GID_USERPOS_LIST_CMDID,
1870 	WMI_10_4_PDEV_CHECK_CAL_VERSION_CMDID,
1871 	WMI_10_4_COEX_VERSION_CFG_CMID,
1872 	WMI_10_4_PDEV_GET_RX_FILTER_CMDID,
1873 	WMI_10_4_PDEV_EXTENDED_NSS_CFG_CMDID,
1874 	WMI_10_4_VDEV_SET_SCAN_NAC_RSSI_CMDID,
1875 	WMI_10_4_PROG_GPIO_BAND_SELECT_CMDID,
1876 	WMI_10_4_CONFIG_SMART_LOGGING_CMDID,
1877 	WMI_10_4_DEBUG_FATAL_CONDITION_CMDID,
1878 	WMI_10_4_GET_TSF_TIMER_CMDID,
1879 	WMI_10_4_PDEV_GET_TPC_TABLE_CMDID,
1880 	WMI_10_4_VDEV_SIFS_TRIGGER_TIME_CMDID,
1881 	WMI_10_4_PDEV_WDS_ENTRY_LIST_CMDID,
1882 	WMI_10_4_TDLS_SET_STATE_CMDID,
1883 	WMI_10_4_TDLS_PEER_UPDATE_CMDID,
1884 	WMI_10_4_TDLS_SET_OFFCHAN_MODE_CMDID,
1885 	WMI_10_4_PDEV_SEND_FD_CMDID,
1886 	WMI_10_4_ENABLE_FILS_CMDID,
1887 	WMI_10_4_PDEV_SET_BRIDGE_MACADDR_CMDID,
1888 	WMI_10_4_ATF_GROUP_WMM_AC_CONFIG_REQUEST_CMDID,
1889 	WMI_10_4_RADAR_FOUND_CMDID,
1890 	WMI_10_4_PEER_CFR_CAPTURE_CMDID,
1891 	WMI_10_4_PER_PEER_PER_TID_CONFIG_CMDID,
1892 	WMI_10_4_PDEV_UTF_CMDID = WMI_10_4_END_CMDID - 1,
1893 };
1894 
1895 enum wmi_10_4_event_id {
1896 	WMI_10_4_SERVICE_READY_EVENTID = 0x8000,
1897 	WMI_10_4_READY_EVENTID,
1898 	WMI_10_4_DEBUG_MESG_EVENTID,
1899 	WMI_10_4_START_EVENTID = 0x9000,
1900 	WMI_10_4_END_EVENTID = 0x9FFF,
1901 	WMI_10_4_SCAN_EVENTID = WMI_10_4_START_EVENTID,
1902 	WMI_10_4_ECHO_EVENTID,
1903 	WMI_10_4_UPDATE_STATS_EVENTID,
1904 	WMI_10_4_INST_RSSI_STATS_EVENTID,
1905 	WMI_10_4_VDEV_START_RESP_EVENTID,
1906 	WMI_10_4_VDEV_STANDBY_REQ_EVENTID,
1907 	WMI_10_4_VDEV_RESUME_REQ_EVENTID,
1908 	WMI_10_4_VDEV_STOPPED_EVENTID,
1909 	WMI_10_4_PEER_STA_KICKOUT_EVENTID,
1910 	WMI_10_4_HOST_SWBA_EVENTID,
1911 	WMI_10_4_TBTTOFFSET_UPDATE_EVENTID,
1912 	WMI_10_4_MGMT_RX_EVENTID,
1913 	WMI_10_4_CHAN_INFO_EVENTID,
1914 	WMI_10_4_PHYERR_EVENTID,
1915 	WMI_10_4_ROAM_EVENTID,
1916 	WMI_10_4_PROFILE_MATCH,
1917 	WMI_10_4_DEBUG_PRINT_EVENTID,
1918 	WMI_10_4_PDEV_QVIT_EVENTID,
1919 	WMI_10_4_WLAN_PROFILE_DATA_EVENTID,
1920 	WMI_10_4_RTT_MEASUREMENT_REPORT_EVENTID,
1921 	WMI_10_4_TSF_MEASUREMENT_REPORT_EVENTID,
1922 	WMI_10_4_RTT_ERROR_REPORT_EVENTID,
1923 	WMI_10_4_RTT_KEEPALIVE_EVENTID,
1924 	WMI_10_4_OEM_CAPABILITY_EVENTID,
1925 	WMI_10_4_OEM_MEASUREMENT_REPORT_EVENTID,
1926 	WMI_10_4_OEM_ERROR_REPORT_EVENTID,
1927 	WMI_10_4_NAN_EVENTID,
1928 	WMI_10_4_WOW_WAKEUP_HOST_EVENTID,
1929 	WMI_10_4_GTK_OFFLOAD_STATUS_EVENTID,
1930 	WMI_10_4_GTK_REKEY_FAIL_EVENTID,
1931 	WMI_10_4_DCS_INTERFERENCE_EVENTID,
1932 	WMI_10_4_PDEV_TPC_CONFIG_EVENTID,
1933 	WMI_10_4_CSA_HANDLING_EVENTID,
1934 	WMI_10_4_GPIO_INPUT_EVENTID,
1935 	WMI_10_4_PEER_RATECODE_LIST_EVENTID,
1936 	WMI_10_4_GENERIC_BUFFER_EVENTID,
1937 	WMI_10_4_MCAST_BUF_RELEASE_EVENTID,
1938 	WMI_10_4_MCAST_LIST_AGEOUT_EVENTID,
1939 	WMI_10_4_VDEV_GET_KEEPALIVE_EVENTID,
1940 	WMI_10_4_WDS_PEER_EVENTID,
1941 	WMI_10_4_PEER_STA_PS_STATECHG_EVENTID,
1942 	WMI_10_4_PDEV_FIPS_EVENTID,
1943 	WMI_10_4_TT_STATS_EVENTID,
1944 	WMI_10_4_PDEV_CHANNEL_HOPPING_EVENTID,
1945 	WMI_10_4_PDEV_ANI_CCK_LEVEL_EVENTID,
1946 	WMI_10_4_PDEV_ANI_OFDM_LEVEL_EVENTID,
1947 	WMI_10_4_PDEV_RESERVE_AST_ENTRY_EVENTID,
1948 	WMI_10_4_PDEV_NFCAL_POWER_EVENTID,
1949 	WMI_10_4_PDEV_TPC_EVENTID,
1950 	WMI_10_4_PDEV_GET_AST_INFO_EVENTID,
1951 	WMI_10_4_PDEV_TEMPERATURE_EVENTID,
1952 	WMI_10_4_PDEV_NFCAL_POWER_ALL_CHANNELS_EVENTID,
1953 	WMI_10_4_PDEV_BSS_CHAN_INFO_EVENTID,
1954 	WMI_10_4_MU_REPORT_EVENTID,
1955 	WMI_10_4_TX_DATA_TRAFFIC_CTRL_EVENTID,
1956 	WMI_10_4_PEER_TX_MU_TXMIT_COUNT_EVENTID,
1957 	WMI_10_4_PEER_GID_USERPOS_LIST_EVENTID,
1958 	WMI_10_4_PDEV_CHECK_CAL_VERSION_EVENTID,
1959 	WMI_10_4_ATF_PEER_STATS_EVENTID,
1960 	WMI_10_4_PDEV_GET_RX_FILTER_EVENTID,
1961 	WMI_10_4_NAC_RSSI_EVENTID,
1962 	WMI_10_4_DEBUG_FATAL_CONDITION_EVENTID,
1963 	WMI_10_4_GET_TSF_TIMER_RESP_EVENTID,
1964 	WMI_10_4_PDEV_TPC_TABLE_EVENTID,
1965 	WMI_10_4_PDEV_WDS_ENTRY_LIST_EVENTID,
1966 	WMI_10_4_TDLS_PEER_EVENTID,
1967 	WMI_10_4_HOST_SWFDA_EVENTID,
1968 	WMI_10_4_ESP_ESTIMATE_EVENTID,
1969 	WMI_10_4_DFS_STATUS_CHECK_EVENTID,
1970 	WMI_10_4_PDEV_UTF_EVENTID = WMI_10_4_END_EVENTID - 1,
1971 };
1972 
1973 enum wmi_phy_mode {
1974 	MODE_11A        = 0,   /* 11a Mode */
1975 	MODE_11G        = 1,   /* 11b/g Mode */
1976 	MODE_11B        = 2,   /* 11b Mode */
1977 	MODE_11GONLY    = 3,   /* 11g only Mode */
1978 	MODE_11NA_HT20   = 4,  /* 11a HT20 mode */
1979 	MODE_11NG_HT20   = 5,  /* 11g HT20 mode */
1980 	MODE_11NA_HT40   = 6,  /* 11a HT40 mode */
1981 	MODE_11NG_HT40   = 7,  /* 11g HT40 mode */
1982 	MODE_11AC_VHT20 = 8,
1983 	MODE_11AC_VHT40 = 9,
1984 	MODE_11AC_VHT80 = 10,
1985 	/*    MODE_11AC_VHT160 = 11, */
1986 	MODE_11AC_VHT20_2G = 11,
1987 	MODE_11AC_VHT40_2G = 12,
1988 	MODE_11AC_VHT80_2G = 13,
1989 	MODE_11AC_VHT80_80 = 14,
1990 	MODE_11AC_VHT160 = 15,
1991 	MODE_UNKNOWN    = 16,
1992 	MODE_MAX        = 16
1993 };
1994 
ath10k_wmi_phymode_str(enum wmi_phy_mode mode)1995 static inline const char *ath10k_wmi_phymode_str(enum wmi_phy_mode mode)
1996 {
1997 	switch (mode) {
1998 	case MODE_11A:
1999 		return "11a";
2000 	case MODE_11G:
2001 		return "11g";
2002 	case MODE_11B:
2003 		return "11b";
2004 	case MODE_11GONLY:
2005 		return "11gonly";
2006 	case MODE_11NA_HT20:
2007 		return "11na-ht20";
2008 	case MODE_11NG_HT20:
2009 		return "11ng-ht20";
2010 	case MODE_11NA_HT40:
2011 		return "11na-ht40";
2012 	case MODE_11NG_HT40:
2013 		return "11ng-ht40";
2014 	case MODE_11AC_VHT20:
2015 		return "11ac-vht20";
2016 	case MODE_11AC_VHT40:
2017 		return "11ac-vht40";
2018 	case MODE_11AC_VHT80:
2019 		return "11ac-vht80";
2020 	case MODE_11AC_VHT160:
2021 		return "11ac-vht160";
2022 	case MODE_11AC_VHT80_80:
2023 		return "11ac-vht80+80";
2024 	case MODE_11AC_VHT20_2G:
2025 		return "11ac-vht20-2g";
2026 	case MODE_11AC_VHT40_2G:
2027 		return "11ac-vht40-2g";
2028 	case MODE_11AC_VHT80_2G:
2029 		return "11ac-vht80-2g";
2030 	case MODE_UNKNOWN:
2031 		/* skip */
2032 		break;
2033 
2034 		/* no default handler to allow compiler to check that the
2035 		 * enum is fully handled
2036 		 */
2037 	}
2038 
2039 	return "<unknown>";
2040 }
2041 
2042 #define WMI_CHAN_LIST_TAG	0x1
2043 #define WMI_SSID_LIST_TAG	0x2
2044 #define WMI_BSSID_LIST_TAG	0x3
2045 #define WMI_IE_TAG		0x4
2046 
2047 struct wmi_channel {
2048 	__le32 mhz;
2049 	__le32 band_center_freq1;
2050 	__le32 band_center_freq2; /* valid for 11ac, 80plus80 */
2051 	union {
2052 		__le32 flags; /* WMI_CHAN_FLAG_ */
2053 		struct {
2054 			u8 mode; /* only 6 LSBs */
2055 		} __packed;
2056 	} __packed;
2057 	union {
2058 		__le32 reginfo0;
2059 		struct {
2060 			/* note: power unit is 0.5 dBm */
2061 			u8 min_power;
2062 			u8 max_power;
2063 			u8 reg_power;
2064 			u8 reg_classid;
2065 		} __packed;
2066 	} __packed;
2067 	union {
2068 		__le32 reginfo1;
2069 		struct {
2070 			/* note: power unit is 1 dBm */
2071 			u8 antenna_max;
2072 			/* note: power unit is 0.5 dBm */
2073 			u8 max_tx_power;
2074 		} __packed;
2075 	} __packed;
2076 } __packed;
2077 
2078 struct wmi_channel_arg {
2079 	u32 freq;
2080 	u32 band_center_freq1;
2081 	u32 band_center_freq2;
2082 	bool passive;
2083 	bool allow_ibss;
2084 	bool allow_ht;
2085 	bool allow_vht;
2086 	bool ht40plus;
2087 	bool chan_radar;
2088 	/* note: power unit is 0.5 dBm */
2089 	u32 min_power;
2090 	u32 max_power;
2091 	u32 max_reg_power;
2092 	/* note: power unit is 1 dBm */
2093 	u32 max_antenna_gain;
2094 	u32 reg_class_id;
2095 	enum wmi_phy_mode mode;
2096 };
2097 
2098 enum wmi_channel_change_cause {
2099 	WMI_CHANNEL_CHANGE_CAUSE_NONE = 0,
2100 	WMI_CHANNEL_CHANGE_CAUSE_CSA,
2101 };
2102 
2103 #define WMI_CHAN_FLAG_HT40_PLUS      (1 << 6)
2104 #define WMI_CHAN_FLAG_PASSIVE        (1 << 7)
2105 #define WMI_CHAN_FLAG_ADHOC_ALLOWED  (1 << 8)
2106 #define WMI_CHAN_FLAG_AP_DISABLED    (1 << 9)
2107 #define WMI_CHAN_FLAG_DFS            (1 << 10)
2108 #define WMI_CHAN_FLAG_ALLOW_HT       (1 << 11)
2109 #define WMI_CHAN_FLAG_ALLOW_VHT      (1 << 12)
2110 
2111 /* Indicate reason for channel switch */
2112 #define WMI_CHANNEL_CHANGE_CAUSE_CSA (1 << 13)
2113 /* DFS required on channel for 2nd segment of VHT160 and VHT80+80*/
2114 #define WMI_CHAN_FLAG_DFS_CFREQ2  (1 << 15)
2115 #define WMI_MAX_SPATIAL_STREAM        3 /* default max ss */
2116 
2117 /* HT Capabilities*/
2118 #define WMI_HT_CAP_ENABLED                0x0001   /* HT Enabled/ disabled */
2119 #define WMI_HT_CAP_HT20_SGI       0x0002   /* Short Guard Interval with HT20 */
2120 #define WMI_HT_CAP_DYNAMIC_SMPS           0x0004   /* Dynamic MIMO powersave */
2121 #define WMI_HT_CAP_TX_STBC                0x0008   /* B3 TX STBC */
2122 #define WMI_HT_CAP_TX_STBC_MASK_SHIFT     3
2123 #define WMI_HT_CAP_RX_STBC                0x0030   /* B4-B5 RX STBC */
2124 #define WMI_HT_CAP_RX_STBC_MASK_SHIFT     4
2125 #define WMI_HT_CAP_LDPC                   0x0040   /* LDPC supported */
2126 #define WMI_HT_CAP_L_SIG_TXOP_PROT        0x0080   /* L-SIG TXOP Protection */
2127 #define WMI_HT_CAP_MPDU_DENSITY           0x0700   /* MPDU Density */
2128 #define WMI_HT_CAP_MPDU_DENSITY_MASK_SHIFT 8
2129 #define WMI_HT_CAP_HT40_SGI               0x0800
2130 #define WMI_HT_CAP_RX_LDPC                0x1000   /* LDPC RX support */
2131 #define WMI_HT_CAP_TX_LDPC                0x2000   /* LDPC TX support */
2132 
2133 #define WMI_HT_CAP_DEFAULT_ALL (WMI_HT_CAP_ENABLED       | \
2134 				WMI_HT_CAP_HT20_SGI      | \
2135 				WMI_HT_CAP_HT40_SGI      | \
2136 				WMI_HT_CAP_TX_STBC       | \
2137 				WMI_HT_CAP_RX_STBC       | \
2138 				WMI_HT_CAP_LDPC)
2139 
2140 /*
2141  * WMI_VHT_CAP_* these maps to ieee 802.11ac vht capability information
2142  * field. The fields not defined here are not supported, or reserved.
2143  * Do not change these masks and if you have to add new one follow the
2144  * bitmask as specified by 802.11ac draft.
2145  */
2146 
2147 #define WMI_VHT_CAP_MAX_MPDU_LEN_MASK            0x00000003
2148 #define WMI_VHT_CAP_RX_LDPC                      0x00000010
2149 #define WMI_VHT_CAP_SGI_80MHZ                    0x00000020
2150 #define WMI_VHT_CAP_SGI_160MHZ                   0x00000040
2151 #define WMI_VHT_CAP_TX_STBC                      0x00000080
2152 #define WMI_VHT_CAP_RX_STBC_MASK                 0x00000300
2153 #define WMI_VHT_CAP_RX_STBC_MASK_SHIFT           8
2154 #define WMI_VHT_CAP_SU_BFER                      0x00000800
2155 #define WMI_VHT_CAP_SU_BFEE                      0x00001000
2156 #define WMI_VHT_CAP_MAX_CS_ANT_MASK              0x0000E000
2157 #define WMI_VHT_CAP_MAX_CS_ANT_MASK_SHIFT        13
2158 #define WMI_VHT_CAP_MAX_SND_DIM_MASK             0x00070000
2159 #define WMI_VHT_CAP_MAX_SND_DIM_MASK_SHIFT       16
2160 #define WMI_VHT_CAP_MU_BFER                      0x00080000
2161 #define WMI_VHT_CAP_MU_BFEE                      0x00100000
2162 #define WMI_VHT_CAP_MAX_AMPDU_LEN_EXP            0x03800000
2163 #define WMI_VHT_CAP_MAX_AMPDU_LEN_EXP_SHIFT      23
2164 #define WMI_VHT_CAP_RX_FIXED_ANT                 0x10000000
2165 #define WMI_VHT_CAP_TX_FIXED_ANT                 0x20000000
2166 
2167 /* The following also refer for max HT AMSDU */
2168 #define WMI_VHT_CAP_MAX_MPDU_LEN_3839            0x00000000
2169 #define WMI_VHT_CAP_MAX_MPDU_LEN_7935            0x00000001
2170 #define WMI_VHT_CAP_MAX_MPDU_LEN_11454           0x00000002
2171 
2172 #define WMI_VHT_CAP_DEFAULT_ALL (WMI_VHT_CAP_MAX_MPDU_LEN_11454  | \
2173 				 WMI_VHT_CAP_RX_LDPC             | \
2174 				 WMI_VHT_CAP_SGI_80MHZ           | \
2175 				 WMI_VHT_CAP_TX_STBC             | \
2176 				 WMI_VHT_CAP_RX_STBC_MASK        | \
2177 				 WMI_VHT_CAP_MAX_AMPDU_LEN_EXP   | \
2178 				 WMI_VHT_CAP_RX_FIXED_ANT        | \
2179 				 WMI_VHT_CAP_TX_FIXED_ANT)
2180 
2181 /*
2182  * Interested readers refer to Rx/Tx MCS Map definition as defined in
2183  * 802.11ac
2184  */
2185 #define WMI_VHT_MAX_MCS_4_SS_MASK(r, ss)      ((3 & (r)) << (((ss) - 1) << 1))
2186 #define WMI_VHT_MAX_SUPP_RATE_MASK           0x1fff0000
2187 #define WMI_VHT_MAX_SUPP_RATE_MASK_SHIFT     16
2188 
2189 enum {
2190 	REGDMN_MODE_11A              = 0x00001, /* 11a channels */
2191 	REGDMN_MODE_TURBO            = 0x00002, /* 11a turbo-only channels */
2192 	REGDMN_MODE_11B              = 0x00004, /* 11b channels */
2193 	REGDMN_MODE_PUREG            = 0x00008, /* 11g channels (OFDM only) */
2194 	REGDMN_MODE_11G              = 0x00008, /* XXX historical */
2195 	REGDMN_MODE_108G             = 0x00020, /* 11a+Turbo channels */
2196 	REGDMN_MODE_108A             = 0x00040, /* 11g+Turbo channels */
2197 	REGDMN_MODE_XR               = 0x00100, /* XR channels */
2198 	REGDMN_MODE_11A_HALF_RATE    = 0x00200, /* 11A half rate channels */
2199 	REGDMN_MODE_11A_QUARTER_RATE = 0x00400, /* 11A quarter rate channels */
2200 	REGDMN_MODE_11NG_HT20        = 0x00800, /* 11N-G HT20 channels */
2201 	REGDMN_MODE_11NA_HT20        = 0x01000, /* 11N-A HT20 channels */
2202 	REGDMN_MODE_11NG_HT40PLUS    = 0x02000, /* 11N-G HT40 + channels */
2203 	REGDMN_MODE_11NG_HT40MINUS   = 0x04000, /* 11N-G HT40 - channels */
2204 	REGDMN_MODE_11NA_HT40PLUS    = 0x08000, /* 11N-A HT40 + channels */
2205 	REGDMN_MODE_11NA_HT40MINUS   = 0x10000, /* 11N-A HT40 - channels */
2206 	REGDMN_MODE_11AC_VHT20       = 0x20000, /* 5Ghz, VHT20 */
2207 	REGDMN_MODE_11AC_VHT40PLUS   = 0x40000, /* 5Ghz, VHT40 + channels */
2208 	REGDMN_MODE_11AC_VHT40MINUS  = 0x80000, /* 5Ghz  VHT40 - channels */
2209 	REGDMN_MODE_11AC_VHT80       = 0x100000, /* 5Ghz, VHT80 channels */
2210 	REGDMN_MODE_11AC_VHT160      = 0x200000,     /* 5Ghz, VHT160 channels */
2211 	REGDMN_MODE_11AC_VHT80_80    = 0x400000,     /* 5Ghz, VHT80+80 channels */
2212 	REGDMN_MODE_ALL              = 0xffffffff
2213 };
2214 
2215 #define REGDMN_CAP1_CHAN_HALF_RATE        0x00000001
2216 #define REGDMN_CAP1_CHAN_QUARTER_RATE     0x00000002
2217 #define REGDMN_CAP1_CHAN_HAL49GHZ         0x00000004
2218 
2219 /* regulatory capabilities */
2220 #define REGDMN_EEPROM_EEREGCAP_EN_FCC_MIDBAND   0x0040
2221 #define REGDMN_EEPROM_EEREGCAP_EN_KK_U1_EVEN    0x0080
2222 #define REGDMN_EEPROM_EEREGCAP_EN_KK_U2         0x0100
2223 #define REGDMN_EEPROM_EEREGCAP_EN_KK_MIDBAND    0x0200
2224 #define REGDMN_EEPROM_EEREGCAP_EN_KK_U1_ODD     0x0400
2225 #define REGDMN_EEPROM_EEREGCAP_EN_KK_NEW_11A    0x0800
2226 
2227 struct hal_reg_capabilities {
2228 	/* regdomain value specified in EEPROM */
2229 	__le32 eeprom_rd;
2230 	/*regdomain */
2231 	__le32 eeprom_rd_ext;
2232 	/* CAP1 capabilities bit map. */
2233 	__le32 regcap1;
2234 	/* REGDMN EEPROM CAP. */
2235 	__le32 regcap2;
2236 	/* REGDMN MODE */
2237 	__le32 wireless_modes;
2238 	__le32 low_2ghz_chan;
2239 	__le32 high_2ghz_chan;
2240 	__le32 low_5ghz_chan;
2241 	__le32 high_5ghz_chan;
2242 } __packed;
2243 
2244 enum wlan_mode_capability {
2245 	WHAL_WLAN_11A_CAPABILITY   = 0x1,
2246 	WHAL_WLAN_11G_CAPABILITY   = 0x2,
2247 	WHAL_WLAN_11AG_CAPABILITY  = 0x3,
2248 };
2249 
2250 /* structure used by FW for requesting host memory */
2251 struct wlan_host_mem_req {
2252 	/* ID of the request */
2253 	__le32 req_id;
2254 	/* size of the  of each unit */
2255 	__le32 unit_size;
2256 	/* flags to  indicate that
2257 	 * the number units is dependent
2258 	 * on number of resources(num vdevs num peers .. etc)
2259 	 */
2260 	__le32 num_unit_info;
2261 	/*
2262 	 * actual number of units to allocate . if flags in the num_unit_info
2263 	 * indicate that number of units is tied to number of a particular
2264 	 * resource to allocate then  num_units filed is set to 0 and host
2265 	 * will derive the number units from number of the resources it is
2266 	 * requesting.
2267 	 */
2268 	__le32 num_units;
2269 } __packed;
2270 
2271 /*
2272  * The following struct holds optional payload for
2273  * wmi_service_ready_event,e.g., 11ac pass some of the
2274  * device capability to the host.
2275  */
2276 struct wmi_service_ready_event {
2277 	__le32 sw_version;
2278 	__le32 sw_version_1;
2279 	__le32 abi_version;
2280 	/* WMI_PHY_CAPABILITY */
2281 	__le32 phy_capability;
2282 	/* Maximum number of frag table entries that SW will populate less 1 */
2283 	__le32 max_frag_entry;
2284 	__le32 wmi_service_bitmap[16];
2285 	__le32 num_rf_chains;
2286 	/*
2287 	 * The following field is only valid for service type
2288 	 * WMI_SERVICE_11AC
2289 	 */
2290 	__le32 ht_cap_info; /* WMI HT Capability */
2291 	__le32 vht_cap_info; /* VHT capability info field of 802.11ac */
2292 	__le32 vht_supp_mcs; /* VHT Supported MCS Set field Rx/Tx same */
2293 	__le32 hw_min_tx_power;
2294 	__le32 hw_max_tx_power;
2295 	struct hal_reg_capabilities hal_reg_capabilities;
2296 	__le32 sys_cap_info;
2297 	__le32 min_pkt_size_enable; /* Enterprise mode short pkt enable */
2298 	/*
2299 	 * Max beacon and Probe Response IE offload size
2300 	 * (includes optional P2P IEs)
2301 	 */
2302 	__le32 max_bcn_ie_size;
2303 	/*
2304 	 * request to host to allocate a chuck of memory and pss it down to FW
2305 	 * via WM_INIT. FW uses this as FW extesnsion memory for saving its
2306 	 * data structures. Only valid for low latency interfaces like PCIE
2307 	 * where FW can access this memory directly (or) by DMA.
2308 	 */
2309 	__le32 num_mem_reqs;
2310 	struct wlan_host_mem_req mem_reqs[];
2311 } __packed;
2312 
2313 /* This is the definition from 10.X firmware branch */
2314 struct wmi_10x_service_ready_event {
2315 	__le32 sw_version;
2316 	__le32 abi_version;
2317 
2318 	/* WMI_PHY_CAPABILITY */
2319 	__le32 phy_capability;
2320 
2321 	/* Maximum number of frag table entries that SW will populate less 1 */
2322 	__le32 max_frag_entry;
2323 	__le32 wmi_service_bitmap[16];
2324 	__le32 num_rf_chains;
2325 
2326 	/*
2327 	 * The following field is only valid for service type
2328 	 * WMI_SERVICE_11AC
2329 	 */
2330 	__le32 ht_cap_info; /* WMI HT Capability */
2331 	__le32 vht_cap_info; /* VHT capability info field of 802.11ac */
2332 	__le32 vht_supp_mcs; /* VHT Supported MCS Set field Rx/Tx same */
2333 	__le32 hw_min_tx_power;
2334 	__le32 hw_max_tx_power;
2335 
2336 	struct hal_reg_capabilities hal_reg_capabilities;
2337 
2338 	__le32 sys_cap_info;
2339 	__le32 min_pkt_size_enable; /* Enterprise mode short pkt enable */
2340 
2341 	/*
2342 	 * request to host to allocate a chuck of memory and pss it down to FW
2343 	 * via WM_INIT. FW uses this as FW extesnsion memory for saving its
2344 	 * data structures. Only valid for low latency interfaces like PCIE
2345 	 * where FW can access this memory directly (or) by DMA.
2346 	 */
2347 	__le32 num_mem_reqs;
2348 
2349 	struct wlan_host_mem_req mem_reqs[];
2350 } __packed;
2351 
2352 #define WMI_SERVICE_READY_TIMEOUT_HZ (5 * HZ)
2353 #define WMI_UNIFIED_READY_TIMEOUT_HZ (5 * HZ)
2354 
2355 struct wmi_ready_event {
2356 	__le32 sw_version;
2357 	__le32 abi_version;
2358 	struct wmi_mac_addr mac_addr;
2359 	__le32 status;
2360 } __packed;
2361 
2362 struct wmi_resource_config {
2363 	/* number of virtual devices (VAPs) to support */
2364 	__le32 num_vdevs;
2365 
2366 	/* number of peer nodes to support */
2367 	__le32 num_peers;
2368 
2369 	/*
2370 	 * In offload mode target supports features like WOW, chatter and
2371 	 * other protocol offloads. In order to support them some
2372 	 * functionalities like reorder buffering, PN checking need to be
2373 	 * done in target. This determines maximum number of peers supported
2374 	 * by target in offload mode
2375 	 */
2376 	__le32 num_offload_peers;
2377 
2378 	/* For target-based RX reordering */
2379 	__le32 num_offload_reorder_bufs;
2380 
2381 	/* number of keys per peer */
2382 	__le32 num_peer_keys;
2383 
2384 	/* total number of TX/RX data TIDs */
2385 	__le32 num_tids;
2386 
2387 	/*
2388 	 * max skid for resolving hash collisions
2389 	 *
2390 	 *   The address search table is sparse, so that if two MAC addresses
2391 	 *   result in the same hash value, the second of these conflicting
2392 	 *   entries can slide to the next index in the address search table,
2393 	 *   and use it, if it is unoccupied.  This ast_skid_limit parameter
2394 	 *   specifies the upper bound on how many subsequent indices to search
2395 	 *   over to find an unoccupied space.
2396 	 */
2397 	__le32 ast_skid_limit;
2398 
2399 	/*
2400 	 * the nominal chain mask for transmit
2401 	 *
2402 	 *   The chain mask may be modified dynamically, e.g. to operate AP
2403 	 *   tx with a reduced number of chains if no clients are associated.
2404 	 *   This configuration parameter specifies the nominal chain-mask that
2405 	 *   should be used when not operating with a reduced set of tx chains.
2406 	 */
2407 	__le32 tx_chain_mask;
2408 
2409 	/*
2410 	 * the nominal chain mask for receive
2411 	 *
2412 	 *   The chain mask may be modified dynamically, e.g. for a client
2413 	 *   to use a reduced number of chains for receive if the traffic to
2414 	 *   the client is low enough that it doesn't require downlink MIMO
2415 	 *   or antenna diversity.
2416 	 *   This configuration parameter specifies the nominal chain-mask that
2417 	 *   should be used when not operating with a reduced set of rx chains.
2418 	 */
2419 	__le32 rx_chain_mask;
2420 
2421 	/*
2422 	 * what rx reorder timeout (ms) to use for the AC
2423 	 *
2424 	 *   Each WMM access class (voice, video, best-effort, background) will
2425 	 *   have its own timeout value to dictate how long to wait for missing
2426 	 *   rx MPDUs to arrive before flushing subsequent MPDUs that have
2427 	 *   already been received.
2428 	 *   This parameter specifies the timeout in milliseconds for each
2429 	 *   class.
2430 	 */
2431 	__le32 rx_timeout_pri_vi;
2432 	__le32 rx_timeout_pri_vo;
2433 	__le32 rx_timeout_pri_be;
2434 	__le32 rx_timeout_pri_bk;
2435 
2436 	/*
2437 	 * what mode the rx should decap packets to
2438 	 *
2439 	 *   MAC can decap to RAW (no decap), native wifi or Ethernet types
2440 	 *   THis setting also determines the default TX behavior, however TX
2441 	 *   behavior can be modified on a per VAP basis during VAP init
2442 	 */
2443 	__le32 rx_decap_mode;
2444 
2445 	/* what is the maximum number of scan requests that can be queued */
2446 	__le32 scan_max_pending_reqs;
2447 
2448 	/* maximum VDEV that could use BMISS offload */
2449 	__le32 bmiss_offload_max_vdev;
2450 
2451 	/* maximum VDEV that could use offload roaming */
2452 	__le32 roam_offload_max_vdev;
2453 
2454 	/* maximum AP profiles that would push to offload roaming */
2455 	__le32 roam_offload_max_ap_profiles;
2456 
2457 	/*
2458 	 * how many groups to use for mcast->ucast conversion
2459 	 *
2460 	 *   The target's WAL maintains a table to hold information regarding
2461 	 *   which peers belong to a given multicast group, so that if
2462 	 *   multicast->unicast conversion is enabled, the target can convert
2463 	 *   multicast tx frames to a series of unicast tx frames, to each
2464 	 *   peer within the multicast group.
2465 	     This num_mcast_groups configuration parameter tells the target how
2466 	 *   many multicast groups to provide storage for within its multicast
2467 	 *   group membership table.
2468 	 */
2469 	__le32 num_mcast_groups;
2470 
2471 	/*
2472 	 * size to alloc for the mcast membership table
2473 	 *
2474 	 *   This num_mcast_table_elems configuration parameter tells the
2475 	 *   target how many peer elements it needs to provide storage for in
2476 	 *   its multicast group membership table.
2477 	 *   These multicast group membership table elements are shared by the
2478 	 *   multicast groups stored within the table.
2479 	 */
2480 	__le32 num_mcast_table_elems;
2481 
2482 	/*
2483 	 * whether/how to do multicast->unicast conversion
2484 	 *
2485 	 *   This configuration parameter specifies whether the target should
2486 	 *   perform multicast --> unicast conversion on transmit, and if so,
2487 	 *   what to do if it finds no entries in its multicast group
2488 	 *   membership table for the multicast IP address in the tx frame.
2489 	 *   Configuration value:
2490 	 *   0 -> Do not perform multicast to unicast conversion.
2491 	 *   1 -> Convert multicast frames to unicast, if the IP multicast
2492 	 *        address from the tx frame is found in the multicast group
2493 	 *        membership table.  If the IP multicast address is not found,
2494 	 *        drop the frame.
2495 	 *   2 -> Convert multicast frames to unicast, if the IP multicast
2496 	 *        address from the tx frame is found in the multicast group
2497 	 *        membership table.  If the IP multicast address is not found,
2498 	 *        transmit the frame as multicast.
2499 	 */
2500 	__le32 mcast2ucast_mode;
2501 
2502 	/*
2503 	 * how much memory to allocate for a tx PPDU dbg log
2504 	 *
2505 	 *   This parameter controls how much memory the target will allocate
2506 	 *   to store a log of tx PPDU meta-information (how large the PPDU
2507 	 *   was, when it was sent, whether it was successful, etc.)
2508 	 */
2509 	__le32 tx_dbg_log_size;
2510 
2511 	/* how many AST entries to be allocated for WDS */
2512 	__le32 num_wds_entries;
2513 
2514 	/*
2515 	 * MAC DMA burst size, e.g., For target PCI limit can be
2516 	 * 0 -default, 1 256B
2517 	 */
2518 	__le32 dma_burst_size;
2519 
2520 	/*
2521 	 * Fixed delimiters to be inserted after every MPDU to
2522 	 * account for interface latency to avoid underrun.
2523 	 */
2524 	__le32 mac_aggr_delim;
2525 
2526 	/*
2527 	 *   determine whether target is responsible for detecting duplicate
2528 	 *   non-aggregate MPDU and timing out stale fragments.
2529 	 *
2530 	 *   A-MPDU reordering is always performed on the target.
2531 	 *
2532 	 *   0: target responsible for frag timeout and dup checking
2533 	 *   1: host responsible for frag timeout and dup checking
2534 	 */
2535 	__le32 rx_skip_defrag_timeout_dup_detection_check;
2536 
2537 	/*
2538 	 * Configuration for VoW :
2539 	 * No of Video Nodes to be supported
2540 	 * and Max no of descriptors for each Video link (node).
2541 	 */
2542 	__le32 vow_config;
2543 
2544 	/* maximum VDEV that could use GTK offload */
2545 	__le32 gtk_offload_max_vdev;
2546 
2547 	/* Number of msdu descriptors target should use */
2548 	__le32 num_msdu_desc;
2549 
2550 	/*
2551 	 * Max. number of Tx fragments per MSDU
2552 	 *  This parameter controls the max number of Tx fragments per MSDU.
2553 	 *  This is sent by the target as part of the WMI_SERVICE_READY event
2554 	 *  and is overridden by the OS shim as required.
2555 	 */
2556 	__le32 max_frag_entries;
2557 } __packed;
2558 
2559 struct wmi_resource_config_10x {
2560 	/* number of virtual devices (VAPs) to support */
2561 	__le32 num_vdevs;
2562 
2563 	/* number of peer nodes to support */
2564 	__le32 num_peers;
2565 
2566 	/* number of keys per peer */
2567 	__le32 num_peer_keys;
2568 
2569 	/* total number of TX/RX data TIDs */
2570 	__le32 num_tids;
2571 
2572 	/*
2573 	 * max skid for resolving hash collisions
2574 	 *
2575 	 *   The address search table is sparse, so that if two MAC addresses
2576 	 *   result in the same hash value, the second of these conflicting
2577 	 *   entries can slide to the next index in the address search table,
2578 	 *   and use it, if it is unoccupied.  This ast_skid_limit parameter
2579 	 *   specifies the upper bound on how many subsequent indices to search
2580 	 *   over to find an unoccupied space.
2581 	 */
2582 	__le32 ast_skid_limit;
2583 
2584 	/*
2585 	 * the nominal chain mask for transmit
2586 	 *
2587 	 *   The chain mask may be modified dynamically, e.g. to operate AP
2588 	 *   tx with a reduced number of chains if no clients are associated.
2589 	 *   This configuration parameter specifies the nominal chain-mask that
2590 	 *   should be used when not operating with a reduced set of tx chains.
2591 	 */
2592 	__le32 tx_chain_mask;
2593 
2594 	/*
2595 	 * the nominal chain mask for receive
2596 	 *
2597 	 *   The chain mask may be modified dynamically, e.g. for a client
2598 	 *   to use a reduced number of chains for receive if the traffic to
2599 	 *   the client is low enough that it doesn't require downlink MIMO
2600 	 *   or antenna diversity.
2601 	 *   This configuration parameter specifies the nominal chain-mask that
2602 	 *   should be used when not operating with a reduced set of rx chains.
2603 	 */
2604 	__le32 rx_chain_mask;
2605 
2606 	/*
2607 	 * what rx reorder timeout (ms) to use for the AC
2608 	 *
2609 	 *   Each WMM access class (voice, video, best-effort, background) will
2610 	 *   have its own timeout value to dictate how long to wait for missing
2611 	 *   rx MPDUs to arrive before flushing subsequent MPDUs that have
2612 	 *   already been received.
2613 	 *   This parameter specifies the timeout in milliseconds for each
2614 	 *   class.
2615 	 */
2616 	__le32 rx_timeout_pri_vi;
2617 	__le32 rx_timeout_pri_vo;
2618 	__le32 rx_timeout_pri_be;
2619 	__le32 rx_timeout_pri_bk;
2620 
2621 	/*
2622 	 * what mode the rx should decap packets to
2623 	 *
2624 	 *   MAC can decap to RAW (no decap), native wifi or Ethernet types
2625 	 *   THis setting also determines the default TX behavior, however TX
2626 	 *   behavior can be modified on a per VAP basis during VAP init
2627 	 */
2628 	__le32 rx_decap_mode;
2629 
2630 	/* what is the maximum number of scan requests that can be queued */
2631 	__le32 scan_max_pending_reqs;
2632 
2633 	/* maximum VDEV that could use BMISS offload */
2634 	__le32 bmiss_offload_max_vdev;
2635 
2636 	/* maximum VDEV that could use offload roaming */
2637 	__le32 roam_offload_max_vdev;
2638 
2639 	/* maximum AP profiles that would push to offload roaming */
2640 	__le32 roam_offload_max_ap_profiles;
2641 
2642 	/*
2643 	 * how many groups to use for mcast->ucast conversion
2644 	 *
2645 	 *   The target's WAL maintains a table to hold information regarding
2646 	 *   which peers belong to a given multicast group, so that if
2647 	 *   multicast->unicast conversion is enabled, the target can convert
2648 	 *   multicast tx frames to a series of unicast tx frames, to each
2649 	 *   peer within the multicast group.
2650 	     This num_mcast_groups configuration parameter tells the target how
2651 	 *   many multicast groups to provide storage for within its multicast
2652 	 *   group membership table.
2653 	 */
2654 	__le32 num_mcast_groups;
2655 
2656 	/*
2657 	 * size to alloc for the mcast membership table
2658 	 *
2659 	 *   This num_mcast_table_elems configuration parameter tells the
2660 	 *   target how many peer elements it needs to provide storage for in
2661 	 *   its multicast group membership table.
2662 	 *   These multicast group membership table elements are shared by the
2663 	 *   multicast groups stored within the table.
2664 	 */
2665 	__le32 num_mcast_table_elems;
2666 
2667 	/*
2668 	 * whether/how to do multicast->unicast conversion
2669 	 *
2670 	 *   This configuration parameter specifies whether the target should
2671 	 *   perform multicast --> unicast conversion on transmit, and if so,
2672 	 *   what to do if it finds no entries in its multicast group
2673 	 *   membership table for the multicast IP address in the tx frame.
2674 	 *   Configuration value:
2675 	 *   0 -> Do not perform multicast to unicast conversion.
2676 	 *   1 -> Convert multicast frames to unicast, if the IP multicast
2677 	 *        address from the tx frame is found in the multicast group
2678 	 *        membership table.  If the IP multicast address is not found,
2679 	 *        drop the frame.
2680 	 *   2 -> Convert multicast frames to unicast, if the IP multicast
2681 	 *        address from the tx frame is found in the multicast group
2682 	 *        membership table.  If the IP multicast address is not found,
2683 	 *        transmit the frame as multicast.
2684 	 */
2685 	__le32 mcast2ucast_mode;
2686 
2687 	/*
2688 	 * how much memory to allocate for a tx PPDU dbg log
2689 	 *
2690 	 *   This parameter controls how much memory the target will allocate
2691 	 *   to store a log of tx PPDU meta-information (how large the PPDU
2692 	 *   was, when it was sent, whether it was successful, etc.)
2693 	 */
2694 	__le32 tx_dbg_log_size;
2695 
2696 	/* how many AST entries to be allocated for WDS */
2697 	__le32 num_wds_entries;
2698 
2699 	/*
2700 	 * MAC DMA burst size, e.g., For target PCI limit can be
2701 	 * 0 -default, 1 256B
2702 	 */
2703 	__le32 dma_burst_size;
2704 
2705 	/*
2706 	 * Fixed delimiters to be inserted after every MPDU to
2707 	 * account for interface latency to avoid underrun.
2708 	 */
2709 	__le32 mac_aggr_delim;
2710 
2711 	/*
2712 	 *   determine whether target is responsible for detecting duplicate
2713 	 *   non-aggregate MPDU and timing out stale fragments.
2714 	 *
2715 	 *   A-MPDU reordering is always performed on the target.
2716 	 *
2717 	 *   0: target responsible for frag timeout and dup checking
2718 	 *   1: host responsible for frag timeout and dup checking
2719 	 */
2720 	__le32 rx_skip_defrag_timeout_dup_detection_check;
2721 
2722 	/*
2723 	 * Configuration for VoW :
2724 	 * No of Video Nodes to be supported
2725 	 * and Max no of descriptors for each Video link (node).
2726 	 */
2727 	__le32 vow_config;
2728 
2729 	/* Number of msdu descriptors target should use */
2730 	__le32 num_msdu_desc;
2731 
2732 	/*
2733 	 * Max. number of Tx fragments per MSDU
2734 	 *  This parameter controls the max number of Tx fragments per MSDU.
2735 	 *  This is sent by the target as part of the WMI_SERVICE_READY event
2736 	 *  and is overridden by the OS shim as required.
2737 	 */
2738 	__le32 max_frag_entries;
2739 } __packed;
2740 
2741 enum wmi_10_2_feature_mask {
2742 	WMI_10_2_RX_BATCH_MODE = BIT(0),
2743 	WMI_10_2_ATF_CONFIG    = BIT(1),
2744 	WMI_10_2_COEX_GPIO     = BIT(3),
2745 	WMI_10_2_BSS_CHAN_INFO = BIT(6),
2746 	WMI_10_2_PEER_STATS    = BIT(7),
2747 };
2748 
2749 struct wmi_resource_config_10_2 {
2750 	struct wmi_resource_config_10x common;
2751 	__le32 max_peer_ext_stats;
2752 	__le32 smart_ant_cap; /* 0-disable, 1-enable */
2753 	__le32 bk_min_free;
2754 	__le32 be_min_free;
2755 	__le32 vi_min_free;
2756 	__le32 vo_min_free;
2757 	__le32 feature_mask;
2758 } __packed;
2759 
2760 #define NUM_UNITS_IS_NUM_VDEVS         BIT(0)
2761 #define NUM_UNITS_IS_NUM_PEERS         BIT(1)
2762 #define NUM_UNITS_IS_NUM_ACTIVE_PEERS  BIT(2)
2763 
2764 struct wmi_resource_config_10_4 {
2765 	/* Number of virtual devices (VAPs) to support */
2766 	__le32 num_vdevs;
2767 
2768 	/* Number of peer nodes to support */
2769 	__le32 num_peers;
2770 
2771 	/* Number of active peer nodes to support */
2772 	__le32 num_active_peers;
2773 
2774 	/* In offload mode, target supports features like WOW, chatter and other
2775 	 * protocol offloads. In order to support them some functionalities like
2776 	 * reorder buffering, PN checking need to be done in target.
2777 	 * This determines maximum number of peers supported by target in
2778 	 * offload mode.
2779 	 */
2780 	__le32 num_offload_peers;
2781 
2782 	/* Number of reorder buffers available for doing target based reorder
2783 	 * Rx reorder buffering
2784 	 */
2785 	__le32 num_offload_reorder_buffs;
2786 
2787 	/* Number of keys per peer */
2788 	__le32 num_peer_keys;
2789 
2790 	/* Total number of TX/RX data TIDs */
2791 	__le32 num_tids;
2792 
2793 	/* Max skid for resolving hash collisions.
2794 	 * The address search table is sparse, so that if two MAC addresses
2795 	 * result in the same hash value, the second of these conflicting
2796 	 * entries can slide to the next index in the address search table,
2797 	 * and use it, if it is unoccupied.  This ast_skid_limit parameter
2798 	 * specifies the upper bound on how many subsequent indices to search
2799 	 * over to find an unoccupied space.
2800 	 */
2801 	__le32 ast_skid_limit;
2802 
2803 	/* The nominal chain mask for transmit.
2804 	 * The chain mask may be modified dynamically, e.g. to operate AP tx
2805 	 * with a reduced number of chains if no clients are associated.
2806 	 * This configuration parameter specifies the nominal chain-mask that
2807 	 * should be used when not operating with a reduced set of tx chains.
2808 	 */
2809 	__le32 tx_chain_mask;
2810 
2811 	/* The nominal chain mask for receive.
2812 	 * The chain mask may be modified dynamically, e.g. for a client to use
2813 	 * a reduced number of chains for receive if the traffic to the client
2814 	 * is low enough that it doesn't require downlink MIMO or antenna
2815 	 * diversity. This configuration parameter specifies the nominal
2816 	 * chain-mask that should be used when not operating with a reduced
2817 	 * set of rx chains.
2818 	 */
2819 	__le32 rx_chain_mask;
2820 
2821 	/* What rx reorder timeout (ms) to use for the AC.
2822 	 * Each WMM access class (voice, video, best-effort, background) will
2823 	 * have its own timeout value to dictate how long to wait for missing
2824 	 * rx MPDUs to arrive before flushing subsequent MPDUs that have already
2825 	 * been received. This parameter specifies the timeout in milliseconds
2826 	 * for each class.
2827 	 */
2828 	__le32 rx_timeout_pri[4];
2829 
2830 	/* What mode the rx should decap packets to.
2831 	 * MAC can decap to RAW (no decap), native wifi or Ethernet types.
2832 	 * This setting also determines the default TX behavior, however TX
2833 	 * behavior can be modified on a per VAP basis during VAP init
2834 	 */
2835 	__le32 rx_decap_mode;
2836 
2837 	__le32 scan_max_pending_req;
2838 
2839 	__le32 bmiss_offload_max_vdev;
2840 
2841 	__le32 roam_offload_max_vdev;
2842 
2843 	__le32 roam_offload_max_ap_profiles;
2844 
2845 	/* How many groups to use for mcast->ucast conversion.
2846 	 * The target's WAL maintains a table to hold information regarding
2847 	 * which peers belong to a given multicast group, so that if
2848 	 * multicast->unicast conversion is enabled, the target can convert
2849 	 * multicast tx frames to a series of unicast tx frames, to each peer
2850 	 * within the multicast group. This num_mcast_groups configuration
2851 	 * parameter tells the target how many multicast groups to provide
2852 	 * storage for within its multicast group membership table.
2853 	 */
2854 	__le32 num_mcast_groups;
2855 
2856 	/* Size to alloc for the mcast membership table.
2857 	 * This num_mcast_table_elems configuration parameter tells the target
2858 	 * how many peer elements it needs to provide storage for in its
2859 	 * multicast group membership table. These multicast group membership
2860 	 * table elements are shared by the multicast groups stored within
2861 	 * the table.
2862 	 */
2863 	__le32 num_mcast_table_elems;
2864 
2865 	/* Whether/how to do multicast->unicast conversion.
2866 	 * This configuration parameter specifies whether the target should
2867 	 * perform multicast --> unicast conversion on transmit, and if so,
2868 	 * what to do if it finds no entries in its multicast group membership
2869 	 * table for the multicast IP address in the tx frame.
2870 	 * Configuration value:
2871 	 * 0 -> Do not perform multicast to unicast conversion.
2872 	 * 1 -> Convert multicast frames to unicast, if the IP multicast address
2873 	 *      from the tx frame is found in the multicast group membership
2874 	 *      table.  If the IP multicast address is not found, drop the frame
2875 	 * 2 -> Convert multicast frames to unicast, if the IP multicast address
2876 	 *      from the tx frame is found in the multicast group membership
2877 	 *      table.  If the IP multicast address is not found, transmit the
2878 	 *      frame as multicast.
2879 	 */
2880 	__le32 mcast2ucast_mode;
2881 
2882 	/* How much memory to allocate for a tx PPDU dbg log.
2883 	 * This parameter controls how much memory the target will allocate to
2884 	 * store a log of tx PPDU meta-information (how large the PPDU was,
2885 	 * when it was sent, whether it was successful, etc.)
2886 	 */
2887 	__le32 tx_dbg_log_size;
2888 
2889 	/* How many AST entries to be allocated for WDS */
2890 	__le32 num_wds_entries;
2891 
2892 	/* MAC DMA burst size. 0 -default, 1 -256B */
2893 	__le32 dma_burst_size;
2894 
2895 	/* Fixed delimiters to be inserted after every MPDU to account for
2896 	 * interface latency to avoid underrun.
2897 	 */
2898 	__le32 mac_aggr_delim;
2899 
2900 	/* Determine whether target is responsible for detecting duplicate
2901 	 * non-aggregate MPDU and timing out stale fragments. A-MPDU reordering
2902 	 * is always performed on the target.
2903 	 *
2904 	 * 0: target responsible for frag timeout and dup checking
2905 	 * 1: host responsible for frag timeout and dup checking
2906 	 */
2907 	__le32 rx_skip_defrag_timeout_dup_detection_check;
2908 
2909 	/* Configuration for VoW : No of Video nodes to be supported and max
2910 	 * no of descriptors for each video link (node).
2911 	 */
2912 	__le32 vow_config;
2913 
2914 	/* Maximum vdev that could use gtk offload */
2915 	__le32 gtk_offload_max_vdev;
2916 
2917 	/* Number of msdu descriptors target should use */
2918 	__le32 num_msdu_desc;
2919 
2920 	/* Max number of tx fragments per MSDU.
2921 	 * This parameter controls the max number of tx fragments per MSDU.
2922 	 * This will passed by target as part of the WMI_SERVICE_READY event
2923 	 * and is overridden by the OS shim as required.
2924 	 */
2925 	__le32 max_frag_entries;
2926 
2927 	/* Max number of extended peer stats.
2928 	 * This parameter controls the max number of peers for which extended
2929 	 * statistics are supported by target
2930 	 */
2931 	__le32 max_peer_ext_stats;
2932 
2933 	/* Smart antenna capabilities information.
2934 	 * 1 - Smart antenna is enabled
2935 	 * 0 - Smart antenna is disabled
2936 	 * In future this can contain smart antenna specific capabilities.
2937 	 */
2938 	__le32 smart_ant_cap;
2939 
2940 	/* User can configure the buffers allocated for each AC (BE, BK, VI, VO)
2941 	 * during init.
2942 	 */
2943 	__le32 bk_minfree;
2944 	__le32 be_minfree;
2945 	__le32 vi_minfree;
2946 	__le32 vo_minfree;
2947 
2948 	/* Rx batch mode capability.
2949 	 * 1 - Rx batch mode enabled
2950 	 * 0 - Rx batch mode disabled
2951 	 */
2952 	__le32 rx_batchmode;
2953 
2954 	/* Thermal throttling capability.
2955 	 * 1 - Capable of thermal throttling
2956 	 * 0 - Not capable of thermal throttling
2957 	 */
2958 	__le32 tt_support;
2959 
2960 	/* ATF configuration.
2961 	 * 1  - Enable ATF
2962 	 * 0  - Disable ATF
2963 	 */
2964 	__le32 atf_config;
2965 
2966 	/* Configure padding to manage IP header un-alignment
2967 	 * 1  - Enable padding
2968 	 * 0  - Disable padding
2969 	 */
2970 	__le32 iphdr_pad_config;
2971 
2972 	/* qwrap configuration (bits 15-0)
2973 	 * 1  - This is qwrap configuration
2974 	 * 0  - This is not qwrap
2975 	 *
2976 	 * Bits 31-16 is alloc_frag_desc_for_data_pkt (1 enables, 0 disables)
2977 	 * In order to get ack-RSSI reporting and to specify the tx-rate for
2978 	 * individual frames, this option must be enabled.  This uses an extra
2979 	 * 4 bytes per tx-msdu descriptor, so don't enable it unless you need it.
2980 	 */
2981 	__le32 qwrap_config;
2982 } __packed;
2983 
2984 enum wmi_coex_version {
2985 	WMI_NO_COEX_VERSION_SUPPORT	= 0,
2986 	/* 3 wire coex support*/
2987 	WMI_COEX_VERSION_1		= 1,
2988 	/* 2.5 wire coex support*/
2989 	WMI_COEX_VERSION_2		= 2,
2990 	/* 2.5 wire coex with duty cycle support */
2991 	WMI_COEX_VERSION_3		= 3,
2992 	/* 4 wire coex support*/
2993 	WMI_COEX_VERSION_4		= 4,
2994 };
2995 
2996 /**
2997  * enum wmi_10_4_feature_mask - WMI 10.4 feature enable/disable flags
2998  * @WMI_10_4_LTEU_SUPPORT: LTEU config
2999  * @WMI_10_4_COEX_GPIO_SUPPORT: COEX GPIO config
3000  * @WMI_10_4_AUX_RADIO_SPECTRAL_INTF: AUX Radio Enhancement for spectral scan
3001  * @WMI_10_4_AUX_RADIO_CHAN_LOAD_INTF: AUX Radio Enhancement for chan load scan
3002  * @WMI_10_4_BSS_CHANNEL_INFO_64: BSS channel info stats
3003  * @WMI_10_4_PEER_STATS: Per station stats
3004  * @WMI_10_4_VDEV_STATS: Per vdev stats
3005  * @WMI_10_4_TDLS: Implicit TDLS support in firmware enable/disable
3006  * @WMI_10_4_TDLS_OFFCHAN: TDLS offchannel support enable/disable
3007  * @WMI_10_4_TDLS_UAPSD_BUFFER_STA: TDLS buffer sta support enable/disable
3008  * @WMI_10_4_TDLS_UAPSD_SLEEP_STA: TDLS sleep sta support enable/disable
3009  * @WMI_10_4_TDLS_CONN_TRACKER_IN_HOST_MODE: TDLS connection tracker in host
3010  *	enable/disable
3011  * @WMI_10_4_TDLS_EXPLICIT_MODE_ONLY: Explicit TDLS mode enable/disable
3012  * @WMI_10_4_TX_DATA_ACK_RSSI: Enable DATA ACK RSSI if firmware is capable
3013  * @WMI_10_4_EXT_PEER_TID_CONFIGS_SUPPORT:  Firmware supports Extended Peer
3014  *	TID configuration for QoS related settings
3015  * @WMI_10_4_REPORT_AIRTIME: Firmware supports transmit airtime reporting
3016  */
3017 enum wmi_10_4_feature_mask {
3018 	WMI_10_4_LTEU_SUPPORT			= BIT(0),
3019 	WMI_10_4_COEX_GPIO_SUPPORT		= BIT(1),
3020 	WMI_10_4_AUX_RADIO_SPECTRAL_INTF	= BIT(2),
3021 	WMI_10_4_AUX_RADIO_CHAN_LOAD_INTF	= BIT(3),
3022 	WMI_10_4_BSS_CHANNEL_INFO_64		= BIT(4),
3023 	WMI_10_4_PEER_STATS			= BIT(5),
3024 	WMI_10_4_VDEV_STATS			= BIT(6),
3025 	WMI_10_4_TDLS				= BIT(7),
3026 	WMI_10_4_TDLS_OFFCHAN			= BIT(8),
3027 	WMI_10_4_TDLS_UAPSD_BUFFER_STA		= BIT(9),
3028 	WMI_10_4_TDLS_UAPSD_SLEEP_STA		= BIT(10),
3029 	WMI_10_4_TDLS_CONN_TRACKER_IN_HOST_MODE = BIT(11),
3030 	WMI_10_4_TDLS_EXPLICIT_MODE_ONLY	= BIT(12),
3031 	WMI_10_4_TX_DATA_ACK_RSSI               = BIT(16),
3032 	WMI_10_4_EXT_PEER_TID_CONFIGS_SUPPORT	= BIT(17),
3033 	WMI_10_4_REPORT_AIRTIME			= BIT(18),
3034 
3035 };
3036 
3037 /* WMI_GPIO_CONFIG_CMDID */
3038 enum {
3039 	WMI_GPIO_PULL_NONE,
3040 	WMI_GPIO_PULL_UP,
3041 	WMI_GPIO_PULL_DOWN,
3042 };
3043 
3044 enum {
3045 	WMI_GPIO_INTTYPE_DISABLE,
3046 	WMI_GPIO_INTTYPE_RISING_EDGE,
3047 	WMI_GPIO_INTTYPE_FALLING_EDGE,
3048 	WMI_GPIO_INTTYPE_BOTH_EDGE,
3049 	WMI_GPIO_INTTYPE_LEVEL_LOW,
3050 	WMI_GPIO_INTTYPE_LEVEL_HIGH
3051 };
3052 
3053 /* WMI_GPIO_CONFIG_CMDID */
3054 struct wmi_gpio_config_cmd {
3055 	__le32 gpio_num;             /* GPIO number to be setup */
3056 	__le32 input;                /* 0 - Output/ 1 - Input */
3057 	__le32 pull_type;            /* Pull type defined above */
3058 	__le32 intr_mode;            /* Interrupt mode defined above (Input) */
3059 } __packed;
3060 
3061 /* WMI_GPIO_OUTPUT_CMDID */
3062 struct wmi_gpio_output_cmd {
3063 	__le32 gpio_num;    /* GPIO number to be setup */
3064 	__le32 set;         /* Set the GPIO pin*/
3065 } __packed;
3066 
3067 /* WMI_GPIO_INPUT_EVENTID */
3068 struct wmi_gpio_input_event {
3069 	__le32 gpio_num;    /* GPIO number which changed state */
3070 } __packed;
3071 
3072 struct wmi_ext_resource_config_10_4_cmd {
3073 	/* contains enum wmi_host_platform_type */
3074 	__le32 host_platform_config;
3075 	/* see enum wmi_10_4_feature_mask */
3076 	__le32 fw_feature_bitmap;
3077 	/* WLAN priority GPIO number */
3078 	__le32 wlan_gpio_priority;
3079 	/* see enum wmi_coex_version */
3080 	__le32 coex_version;
3081 	/* COEX GPIO config */
3082 	__le32 coex_gpio_pin1;
3083 	__le32 coex_gpio_pin2;
3084 	__le32 coex_gpio_pin3;
3085 	/* number of vdevs allowed to perform tdls */
3086 	__le32 num_tdls_vdevs;
3087 	/* number of peers to track per TDLS vdev */
3088 	__le32 num_tdls_conn_table_entries;
3089 	/* number of tdls sleep sta supported */
3090 	__le32 max_tdls_concurrent_sleep_sta;
3091 	/* number of tdls buffer sta supported */
3092 	__le32 max_tdls_concurrent_buffer_sta;
3093 };
3094 
3095 /* structure describing host memory chunk. */
3096 struct host_memory_chunk {
3097 	/* id of the request that is passed up in service ready */
3098 	__le32 req_id;
3099 	/* the physical address the memory chunk */
3100 	__le32 ptr;
3101 	/* size of the chunk */
3102 	__le32 size;
3103 } __packed;
3104 
3105 #define WMI_IRAM_RECOVERY_HOST_MEM_REQ_ID 8
3106 
3107 struct wmi_host_mem_chunks {
3108 	__le32 count;
3109 	/* some fw revisions require at least 1 chunk regardless of count */
3110 	union {
3111 		struct host_memory_chunk item;
3112 		DECLARE_FLEX_ARRAY(struct host_memory_chunk, items);
3113 	};
3114 } __packed;
3115 
3116 struct wmi_init_cmd {
3117 	struct wmi_resource_config resource_config;
3118 	struct wmi_host_mem_chunks mem_chunks;
3119 } __packed;
3120 
3121 /* _10x structure is from 10.X FW API */
3122 struct wmi_init_cmd_10x {
3123 	struct wmi_resource_config_10x resource_config;
3124 	struct wmi_host_mem_chunks mem_chunks;
3125 } __packed;
3126 
3127 struct wmi_init_cmd_10_2 {
3128 	struct wmi_resource_config_10_2 resource_config;
3129 	struct wmi_host_mem_chunks mem_chunks;
3130 } __packed;
3131 
3132 struct wmi_init_cmd_10_4 {
3133 	struct wmi_resource_config_10_4 resource_config;
3134 	struct wmi_host_mem_chunks mem_chunks;
3135 } __packed;
3136 
3137 struct wmi_chan_list_entry {
3138 	__le16 freq;
3139 	u8 phy_mode; /* valid for 10.2 only */
3140 	u8 reserved;
3141 } __packed;
3142 
3143 /* TLV for channel list */
3144 struct wmi_chan_list {
3145 	__le32 tag; /* WMI_CHAN_LIST_TAG */
3146 	__le32 num_chan;
3147 	struct wmi_chan_list_entry channel_list[];
3148 } __packed;
3149 
3150 struct wmi_bssid_list {
3151 	__le32 tag; /* WMI_BSSID_LIST_TAG */
3152 	__le32 num_bssid;
3153 	struct wmi_mac_addr bssid_list[];
3154 } __packed;
3155 
3156 struct wmi_ie_data {
3157 	__le32 tag; /* WMI_IE_TAG */
3158 	__le32 ie_len;
3159 	u8 ie_data[];
3160 } __packed;
3161 
3162 struct wmi_ssid {
3163 	__le32 ssid_len;
3164 	u8 ssid[32];
3165 } __packed;
3166 
3167 struct wmi_ssid_list {
3168 	__le32 tag; /* WMI_SSID_LIST_TAG */
3169 	__le32 num_ssids;
3170 	struct wmi_ssid ssids[];
3171 } __packed;
3172 
3173 /* prefix used by scan requestor ids on the host */
3174 #define WMI_HOST_SCAN_REQUESTOR_ID_PREFIX 0xA000
3175 
3176 /* prefix used by scan request ids generated on the host */
3177 /* host cycles through the lower 12 bits to generate ids */
3178 #define WMI_HOST_SCAN_REQ_ID_PREFIX 0xA000
3179 
3180 #define WLAN_SCAN_PARAMS_MAX_SSID    16
3181 #define WLAN_SCAN_PARAMS_MAX_BSSID   4
3182 #define WLAN_SCAN_PARAMS_MAX_IE_LEN  256
3183 
3184 /* Values lower than this may be refused by some firmware revisions with a scan
3185  * completion with a timedout reason.
3186  */
3187 #define WMI_SCAN_CHAN_MIN_TIME_MSEC 40
3188 
3189 /* Scan priority numbers must be sequential, starting with 0 */
3190 enum wmi_scan_priority {
3191 	WMI_SCAN_PRIORITY_VERY_LOW = 0,
3192 	WMI_SCAN_PRIORITY_LOW,
3193 	WMI_SCAN_PRIORITY_MEDIUM,
3194 	WMI_SCAN_PRIORITY_HIGH,
3195 	WMI_SCAN_PRIORITY_VERY_HIGH,
3196 	WMI_SCAN_PRIORITY_COUNT   /* number of priorities supported */
3197 };
3198 
3199 struct wmi_start_scan_common {
3200 	/* Scan ID */
3201 	__le32 scan_id;
3202 	/* Scan requestor ID */
3203 	__le32 scan_req_id;
3204 	/* VDEV id(interface) that is requesting scan */
3205 	__le32 vdev_id;
3206 	/* Scan Priority, input to scan scheduler */
3207 	__le32 scan_priority;
3208 	/* Scan events subscription */
3209 	__le32 notify_scan_events;
3210 	/* dwell time in msec on active channels */
3211 	__le32 dwell_time_active;
3212 	/* dwell time in msec on passive channels */
3213 	__le32 dwell_time_passive;
3214 	/*
3215 	 * min time in msec on the BSS channel,only valid if at least one
3216 	 * VDEV is active
3217 	 */
3218 	__le32 min_rest_time;
3219 	/*
3220 	 * max rest time in msec on the BSS channel,only valid if at least
3221 	 * one VDEV is active
3222 	 */
3223 	/*
3224 	 * the scanner will rest on the bss channel at least min_rest_time
3225 	 * after min_rest_time the scanner will start checking for tx/rx
3226 	 * activity on all VDEVs. if there is no activity the scanner will
3227 	 * switch to off channel. if there is activity the scanner will let
3228 	 * the radio on the bss channel until max_rest_time expires.at
3229 	 * max_rest_time scanner will switch to off channel irrespective of
3230 	 * activity. activity is determined by the idle_time parameter.
3231 	 */
3232 	__le32 max_rest_time;
3233 	/*
3234 	 * time before sending next set of probe requests.
3235 	 * The scanner keeps repeating probe requests transmission with
3236 	 * period specified by repeat_probe_time.
3237 	 * The number of probe requests specified depends on the ssid_list
3238 	 * and bssid_list
3239 	 */
3240 	__le32 repeat_probe_time;
3241 	/* time in msec between 2 consecutive probe requests with in a set. */
3242 	__le32 probe_spacing_time;
3243 	/*
3244 	 * data inactivity time in msec on bss channel that will be used by
3245 	 * scanner for measuring the inactivity.
3246 	 */
3247 	__le32 idle_time;
3248 	/* maximum time in msec allowed for scan  */
3249 	__le32 max_scan_time;
3250 	/*
3251 	 * delay in msec before sending first probe request after switching
3252 	 * to a channel
3253 	 */
3254 	__le32 probe_delay;
3255 	/* Scan control flags */
3256 	__le32 scan_ctrl_flags;
3257 } __packed;
3258 
3259 struct wmi_start_scan_cmd {
3260 	struct wmi_start_scan_common common;
3261 	__le32 burst_duration_ms;
3262 	u8 tlvs[];
3263 } __packed;
3264 
3265 /* This is the definition from 10.X firmware branch */
3266 struct wmi_10x_start_scan_cmd {
3267 	struct wmi_start_scan_common common;
3268 	u8 tlvs[];
3269 } __packed;
3270 
3271 struct wmi_ssid_arg {
3272 	int len;
3273 	const u8 *ssid;
3274 };
3275 
3276 struct wmi_bssid_arg {
3277 	const u8 *bssid;
3278 };
3279 
3280 struct wmi_start_scan_arg {
3281 	u32 scan_id;
3282 	u32 scan_req_id;
3283 	u32 vdev_id;
3284 	u32 scan_priority;
3285 	u32 notify_scan_events;
3286 	u32 dwell_time_active;
3287 	u32 dwell_time_passive;
3288 	u32 min_rest_time;
3289 	u32 max_rest_time;
3290 	u32 repeat_probe_time;
3291 	u32 probe_spacing_time;
3292 	u32 idle_time;
3293 	u32 max_scan_time;
3294 	u32 probe_delay;
3295 	u32 scan_ctrl_flags;
3296 	u32 burst_duration_ms;
3297 
3298 	u32 ie_len;
3299 	u32 n_channels;
3300 	u32 n_ssids;
3301 	u32 n_bssids;
3302 
3303 	u8 ie[WLAN_SCAN_PARAMS_MAX_IE_LEN];
3304 	u16 channels[64];
3305 	struct wmi_ssid_arg ssids[WLAN_SCAN_PARAMS_MAX_SSID];
3306 	struct wmi_bssid_arg bssids[WLAN_SCAN_PARAMS_MAX_BSSID];
3307 	struct wmi_mac_addr mac_addr;
3308 	struct wmi_mac_addr mac_mask;
3309 };
3310 
3311 /* scan control flags */
3312 
3313 /* passively scan all channels including active channels */
3314 #define WMI_SCAN_FLAG_PASSIVE        0x1
3315 /* add wild card ssid probe request even though ssid_list is specified. */
3316 #define WMI_SCAN_ADD_BCAST_PROBE_REQ 0x2
3317 /* add cck rates to rates/xrate ie for the generated probe request */
3318 #define WMI_SCAN_ADD_CCK_RATES 0x4
3319 /* add ofdm rates to rates/xrate ie for the generated probe request */
3320 #define WMI_SCAN_ADD_OFDM_RATES 0x8
3321 /* To enable indication of Chan load and Noise floor to host */
3322 #define WMI_SCAN_CHAN_STAT_EVENT 0x10
3323 /* Filter Probe request frames  */
3324 #define WMI_SCAN_FILTER_PROBE_REQ 0x20
3325 /* When set, DFS channels will not be scanned */
3326 #define WMI_SCAN_BYPASS_DFS_CHN 0x40
3327 /* Different FW scan engine may choose to bail out on errors.
3328  * Allow the driver to have influence over that.
3329  */
3330 #define WMI_SCAN_CONTINUE_ON_ERROR 0x80
3331 
3332 /* Use random MAC address for TA for Probe Request frame and add
3333  * OUI specified by WMI_SCAN_PROB_REQ_OUI_CMDID to the Probe Request frame.
3334  * if OUI is not set by WMI_SCAN_PROB_REQ_OUI_CMDID then the flag is ignored.
3335  */
3336 #define WMI_SCAN_ADD_SPOOFED_MAC_IN_PROBE_REQ   0x1000
3337 
3338 /* WMI_SCAN_CLASS_MASK must be the same value as IEEE80211_SCAN_CLASS_MASK */
3339 #define WMI_SCAN_CLASS_MASK 0xFF000000
3340 
3341 enum wmi_stop_scan_type {
3342 	WMI_SCAN_STOP_ONE	= 0x00000000, /* stop by scan_id */
3343 	WMI_SCAN_STOP_VDEV_ALL	= 0x01000000, /* stop by vdev_id */
3344 	WMI_SCAN_STOP_ALL	= 0x04000000, /* stop all scans */
3345 };
3346 
3347 struct wmi_stop_scan_cmd {
3348 	__le32 scan_req_id;
3349 	__le32 scan_id;
3350 	__le32 req_type;
3351 	__le32 vdev_id;
3352 } __packed;
3353 
3354 struct wmi_stop_scan_arg {
3355 	u32 req_id;
3356 	enum wmi_stop_scan_type req_type;
3357 	union {
3358 		u32 scan_id;
3359 		u32 vdev_id;
3360 	} u;
3361 };
3362 
3363 struct wmi_scan_chan_list_cmd {
3364 	__le32 num_scan_chans;
3365 	struct wmi_channel chan_info[];
3366 } __packed;
3367 
3368 struct wmi_scan_chan_list_arg {
3369 	u32 n_channels;
3370 	struct wmi_channel_arg *channels;
3371 };
3372 
3373 enum wmi_bss_filter {
3374 	WMI_BSS_FILTER_NONE = 0,        /* no beacons forwarded */
3375 	WMI_BSS_FILTER_ALL,             /* all beacons forwarded */
3376 	WMI_BSS_FILTER_PROFILE,         /* only beacons matching profile */
3377 	WMI_BSS_FILTER_ALL_BUT_PROFILE, /* all but beacons matching profile */
3378 	WMI_BSS_FILTER_CURRENT_BSS,     /* only beacons matching current BSS */
3379 	WMI_BSS_FILTER_ALL_BUT_BSS,     /* all but beacons matching BSS */
3380 	WMI_BSS_FILTER_PROBED_SSID,     /* beacons matching probed ssid */
3381 	WMI_BSS_FILTER_LAST_BSS,        /* marker only */
3382 };
3383 
3384 enum wmi_scan_event_type {
3385 	WMI_SCAN_EVENT_STARTED              = BIT(0),
3386 	WMI_SCAN_EVENT_COMPLETED            = BIT(1),
3387 	WMI_SCAN_EVENT_BSS_CHANNEL          = BIT(2),
3388 	WMI_SCAN_EVENT_FOREIGN_CHANNEL      = BIT(3),
3389 	WMI_SCAN_EVENT_DEQUEUED             = BIT(4),
3390 	/* possibly by high-prio scan */
3391 	WMI_SCAN_EVENT_PREEMPTED            = BIT(5),
3392 	WMI_SCAN_EVENT_START_FAILED         = BIT(6),
3393 	WMI_SCAN_EVENT_RESTARTED            = BIT(7),
3394 	WMI_SCAN_EVENT_FOREIGN_CHANNEL_EXIT = BIT(8),
3395 	WMI_SCAN_EVENT_MAX                  = BIT(15),
3396 };
3397 
3398 enum wmi_scan_completion_reason {
3399 	WMI_SCAN_REASON_COMPLETED,
3400 	WMI_SCAN_REASON_CANCELLED,
3401 	WMI_SCAN_REASON_PREEMPTED,
3402 	WMI_SCAN_REASON_TIMEDOUT,
3403 	WMI_SCAN_REASON_INTERNAL_FAILURE,
3404 	WMI_SCAN_REASON_MAX,
3405 };
3406 
3407 struct wmi_scan_event {
3408 	__le32 event_type; /* %WMI_SCAN_EVENT_ */
3409 	__le32 reason; /* %WMI_SCAN_REASON_ */
3410 	__le32 channel_freq; /* only valid for WMI_SCAN_EVENT_FOREIGN_CHANNEL */
3411 	__le32 scan_req_id;
3412 	__le32 scan_id;
3413 	__le32 vdev_id;
3414 } __packed;
3415 
3416 /*
3417  * This defines how much headroom is kept in the
3418  * receive frame between the descriptor and the
3419  * payload, in order for the WMI PHY error and
3420  * management handler to insert header contents.
3421  *
3422  * This is in bytes.
3423  */
3424 #define WMI_MGMT_RX_HDR_HEADROOM    52
3425 
3426 /*
3427  * This event will be used for sending scan results
3428  * as well as rx mgmt frames to the host. The rx buffer
3429  * will be sent as part of this WMI event. It would be a
3430  * good idea to pass all the fields in the RX status
3431  * descriptor up to the host.
3432  */
3433 struct wmi_mgmt_rx_hdr_v1 {
3434 	__le32 channel;
3435 	__le32 snr;
3436 	__le32 rate;
3437 	__le32 phy_mode;
3438 	__le32 buf_len;
3439 	__le32 status; /* %WMI_RX_STATUS_ */
3440 } __packed;
3441 
3442 struct wmi_mgmt_rx_hdr_v2 {
3443 	struct wmi_mgmt_rx_hdr_v1 v1;
3444 	__le32 rssi_ctl[4];
3445 } __packed;
3446 
3447 struct wmi_mgmt_rx_event_v1 {
3448 	struct wmi_mgmt_rx_hdr_v1 hdr;
3449 	u8 buf[];
3450 } __packed;
3451 
3452 struct wmi_mgmt_rx_event_v2 {
3453 	struct wmi_mgmt_rx_hdr_v2 hdr;
3454 	u8 buf[];
3455 } __packed;
3456 
3457 struct wmi_10_4_mgmt_rx_hdr {
3458 	__le32 channel;
3459 	__le32 snr;
3460 	    u8 rssi_ctl[4];
3461 	__le32 rate;
3462 	__le32 phy_mode;
3463 	__le32 buf_len;
3464 	__le32 status;
3465 } __packed;
3466 
3467 struct wmi_10_4_mgmt_rx_event {
3468 	struct wmi_10_4_mgmt_rx_hdr hdr;
3469 	u8 buf[];
3470 } __packed;
3471 
3472 struct wmi_mgmt_rx_ext_info {
3473 	__le64 rx_mac_timestamp;
3474 } __packed __aligned(4);
3475 
3476 #define WMI_RX_STATUS_OK			0x00
3477 #define WMI_RX_STATUS_ERR_CRC			0x01
3478 #define WMI_RX_STATUS_ERR_DECRYPT		0x08
3479 #define WMI_RX_STATUS_ERR_MIC			0x10
3480 #define WMI_RX_STATUS_ERR_KEY_CACHE_MISS	0x20
3481 /* Extension data at the end of mgmt frame */
3482 #define WMI_RX_STATUS_EXT_INFO		0x40
3483 
3484 #define PHY_ERROR_GEN_SPECTRAL_SCAN		0x26
3485 #define PHY_ERROR_GEN_FALSE_RADAR_EXT		0x24
3486 #define PHY_ERROR_GEN_RADAR			0x05
3487 
3488 #define PHY_ERROR_10_4_RADAR_MASK               0x4
3489 #define PHY_ERROR_10_4_SPECTRAL_SCAN_MASK       0x4000000
3490 
3491 enum phy_err_type {
3492 	PHY_ERROR_UNKNOWN,
3493 	PHY_ERROR_SPECTRAL_SCAN,
3494 	PHY_ERROR_FALSE_RADAR_EXT,
3495 	PHY_ERROR_RADAR
3496 };
3497 
3498 struct wmi_phyerr {
3499 	__le32 tsf_timestamp;
3500 	__le16 freq1;
3501 	__le16 freq2;
3502 	u8 rssi_combined;
3503 	u8 chan_width_mhz;
3504 	u8 phy_err_code;
3505 	u8 rsvd0;
3506 	__le32 rssi_chains[4];
3507 	__le16 nf_chains[4];
3508 	__le32 buf_len;
3509 	u8 buf[];
3510 } __packed;
3511 
3512 struct wmi_phyerr_event {
3513 	__le32 num_phyerrs;
3514 	__le32 tsf_l32;
3515 	__le32 tsf_u32;
3516 
3517 	/* array of struct wmi_phyerr */
3518 	u8 phyerrs[];
3519 } __packed;
3520 
3521 struct wmi_10_4_phyerr_event {
3522 	__le32 tsf_l32;
3523 	__le32 tsf_u32;
3524 	__le16 freq1;
3525 	__le16 freq2;
3526 	u8 rssi_combined;
3527 	u8 chan_width_mhz;
3528 	u8 phy_err_code;
3529 	u8 rsvd0;
3530 	__le32 rssi_chains[4];
3531 	__le16 nf_chains[4];
3532 	__le32 phy_err_mask[2];
3533 	__le32 tsf_timestamp;
3534 	__le32 buf_len;
3535 	u8 buf[];
3536 } __packed;
3537 
3538 struct wmi_radar_found_info {
3539 	__le32 pri_min;
3540 	__le32 pri_max;
3541 	__le32 width_min;
3542 	__le32 width_max;
3543 	__le32 sidx_min;
3544 	__le32 sidx_max;
3545 } __packed;
3546 
3547 enum wmi_radar_confirmation_status {
3548 	/* Detected radar was due to SW pulses */
3549 	WMI_SW_RADAR_DETECTED    = 0,
3550 
3551 	WMI_RADAR_DETECTION_FAIL = 1,
3552 
3553 	/* Real radar detected */
3554 	WMI_HW_RADAR_DETECTED    = 2,
3555 };
3556 
3557 #define PHYERR_TLV_SIG				0xBB
3558 #define PHYERR_TLV_TAG_SEARCH_FFT_REPORT	0xFB
3559 #define PHYERR_TLV_TAG_RADAR_PULSE_SUMMARY	0xF8
3560 #define PHYERR_TLV_TAG_SPECTRAL_SUMMARY_REPORT	0xF9
3561 
3562 struct phyerr_radar_report {
3563 	__le32 reg0; /* RADAR_REPORT_REG0_* */
3564 	__le32 reg1; /* RADAR_REPORT_REG1_* */
3565 } __packed;
3566 
3567 #define RADAR_REPORT_REG0_PULSE_IS_CHIRP_MASK		0x80000000
3568 #define RADAR_REPORT_REG0_PULSE_IS_CHIRP_LSB		31
3569 
3570 #define RADAR_REPORT_REG0_PULSE_IS_MAX_WIDTH_MASK	0x40000000
3571 #define RADAR_REPORT_REG0_PULSE_IS_MAX_WIDTH_LSB	30
3572 
3573 #define RADAR_REPORT_REG0_AGC_TOTAL_GAIN_MASK		0x3FF00000
3574 #define RADAR_REPORT_REG0_AGC_TOTAL_GAIN_LSB		20
3575 
3576 #define RADAR_REPORT_REG0_PULSE_DELTA_DIFF_MASK		0x000F0000
3577 #define RADAR_REPORT_REG0_PULSE_DELTA_DIFF_LSB		16
3578 
3579 #define RADAR_REPORT_REG0_PULSE_DELTA_PEAK_MASK		0x0000FC00
3580 #define RADAR_REPORT_REG0_PULSE_DELTA_PEAK_LSB		10
3581 
3582 #define RADAR_REPORT_REG0_PULSE_SIDX_MASK		0x000003FF
3583 #define RADAR_REPORT_REG0_PULSE_SIDX_LSB		0
3584 
3585 #define RADAR_REPORT_REG1_PULSE_SRCH_FFT_VALID_MASK	0x80000000
3586 #define RADAR_REPORT_REG1_PULSE_SRCH_FFT_VALID_LSB	31
3587 
3588 #define RADAR_REPORT_REG1_PULSE_AGC_MB_GAIN_MASK	0x7F000000
3589 #define RADAR_REPORT_REG1_PULSE_AGC_MB_GAIN_LSB		24
3590 
3591 #define RADAR_REPORT_REG1_PULSE_SUBCHAN_MASK_MASK	0x00FF0000
3592 #define RADAR_REPORT_REG1_PULSE_SUBCHAN_MASK_LSB	16
3593 
3594 #define RADAR_REPORT_REG1_PULSE_TSF_OFFSET_MASK		0x0000FF00
3595 #define RADAR_REPORT_REG1_PULSE_TSF_OFFSET_LSB		8
3596 
3597 #define RADAR_REPORT_REG1_PULSE_DUR_MASK		0x000000FF
3598 #define RADAR_REPORT_REG1_PULSE_DUR_LSB			0
3599 
3600 struct phyerr_fft_report {
3601 	__le32 reg0; /* SEARCH_FFT_REPORT_REG0_ * */
3602 	__le32 reg1; /* SEARCH_FFT_REPORT_REG1_ * */
3603 } __packed;
3604 
3605 #define SEARCH_FFT_REPORT_REG0_TOTAL_GAIN_DB_MASK	0xFF800000
3606 #define SEARCH_FFT_REPORT_REG0_TOTAL_GAIN_DB_LSB	23
3607 
3608 #define SEARCH_FFT_REPORT_REG0_BASE_PWR_DB_MASK		0x007FC000
3609 #define SEARCH_FFT_REPORT_REG0_BASE_PWR_DB_LSB		14
3610 
3611 #define SEARCH_FFT_REPORT_REG0_FFT_CHN_IDX_MASK		0x00003000
3612 #define SEARCH_FFT_REPORT_REG0_FFT_CHN_IDX_LSB		12
3613 
3614 #define SEARCH_FFT_REPORT_REG0_PEAK_SIDX_MASK		0x00000FFF
3615 #define SEARCH_FFT_REPORT_REG0_PEAK_SIDX_LSB		0
3616 
3617 #define SEARCH_FFT_REPORT_REG1_RELPWR_DB_MASK		0xFC000000
3618 #define SEARCH_FFT_REPORT_REG1_RELPWR_DB_LSB		26
3619 
3620 #define SEARCH_FFT_REPORT_REG1_AVGPWR_DB_MASK		0x03FC0000
3621 #define SEARCH_FFT_REPORT_REG1_AVGPWR_DB_LSB		18
3622 
3623 #define SEARCH_FFT_REPORT_REG1_PEAK_MAG_MASK		0x0003FF00
3624 #define SEARCH_FFT_REPORT_REG1_PEAK_MAG_LSB		8
3625 
3626 #define SEARCH_FFT_REPORT_REG1_NUM_STR_BINS_IB_MASK	0x000000FF
3627 #define SEARCH_FFT_REPORT_REG1_NUM_STR_BINS_IB_LSB	0
3628 
3629 struct phyerr_tlv {
3630 	__le16 len;
3631 	u8 tag;
3632 	u8 sig;
3633 } __packed;
3634 
3635 #define DFS_RSSI_POSSIBLY_FALSE			50
3636 #define DFS_PEAK_MAG_THOLD_POSSIBLY_FALSE	40
3637 
3638 struct wmi_mgmt_tx_hdr {
3639 	__le32 vdev_id;
3640 	struct wmi_mac_addr peer_macaddr;
3641 	__le32 tx_rate;
3642 	__le32 tx_power;
3643 	__le32 buf_len;
3644 } __packed;
3645 
3646 struct wmi_mgmt_tx_cmd {
3647 	struct wmi_mgmt_tx_hdr hdr;
3648 	u8 buf[];
3649 } __packed;
3650 
3651 struct wmi_echo_event {
3652 	__le32 value;
3653 } __packed;
3654 
3655 struct wmi_echo_cmd {
3656 	__le32 value;
3657 } __packed;
3658 
3659 struct wmi_pdev_set_regdomain_cmd {
3660 	__le32 reg_domain;
3661 	__le32 reg_domain_2G;
3662 	__le32 reg_domain_5G;
3663 	__le32 conformance_test_limit_2G;
3664 	__le32 conformance_test_limit_5G;
3665 } __packed;
3666 
3667 enum wmi_dfs_region {
3668 	/* Uninitialized dfs domain */
3669 	WMI_UNINIT_DFS_DOMAIN = 0,
3670 
3671 	/* FCC3 dfs domain */
3672 	WMI_FCC_DFS_DOMAIN = 1,
3673 
3674 	/* ETSI dfs domain */
3675 	WMI_ETSI_DFS_DOMAIN = 2,
3676 
3677 	/*Japan dfs domain */
3678 	WMI_MKK4_DFS_DOMAIN = 3,
3679 };
3680 
3681 struct wmi_pdev_set_regdomain_cmd_10x {
3682 	__le32 reg_domain;
3683 	__le32 reg_domain_2G;
3684 	__le32 reg_domain_5G;
3685 	__le32 conformance_test_limit_2G;
3686 	__le32 conformance_test_limit_5G;
3687 
3688 	/* dfs domain from wmi_dfs_region */
3689 	__le32 dfs_domain;
3690 } __packed;
3691 
3692 /* Command to set/unset chip in quiet mode */
3693 struct wmi_pdev_set_quiet_cmd {
3694 	/* period in TUs */
3695 	__le32 period;
3696 
3697 	/* duration in TUs */
3698 	__le32 duration;
3699 
3700 	/* offset in TUs */
3701 	__le32 next_start;
3702 
3703 	/* enable/disable */
3704 	__le32 enabled;
3705 } __packed;
3706 
3707 /*
3708  * 802.11g protection mode.
3709  */
3710 enum ath10k_protmode {
3711 	ATH10K_PROT_NONE     = 0,    /* no protection */
3712 	ATH10K_PROT_CTSONLY  = 1,    /* CTS to self */
3713 	ATH10K_PROT_RTSCTS   = 2,    /* RTS-CTS */
3714 };
3715 
3716 enum wmi_rtscts_profile {
3717 	WMI_RTSCTS_FOR_NO_RATESERIES = 0,
3718 	WMI_RTSCTS_FOR_SECOND_RATESERIES,
3719 	WMI_RTSCTS_ACROSS_SW_RETRIES
3720 };
3721 
3722 #define WMI_RTSCTS_ENABLED		1
3723 #define WMI_RTSCTS_SET_MASK		0x0f
3724 #define WMI_RTSCTS_SET_LSB		0
3725 
3726 #define WMI_RTSCTS_PROFILE_MASK		0xf0
3727 #define WMI_RTSCTS_PROFILE_LSB		4
3728 
3729 enum wmi_beacon_gen_mode {
3730 	WMI_BEACON_STAGGERED_MODE = 0,
3731 	WMI_BEACON_BURST_MODE = 1
3732 };
3733 
3734 enum wmi_csa_event_ies_present_flag {
3735 	WMI_CSA_IE_PRESENT = 0x00000001,
3736 	WMI_XCSA_IE_PRESENT = 0x00000002,
3737 	WMI_WBW_IE_PRESENT = 0x00000004,
3738 	WMI_CSWARP_IE_PRESENT = 0x00000008,
3739 };
3740 
3741 /* wmi CSA receive event from beacon frame */
3742 struct wmi_csa_event {
3743 	__le32 i_fc_dur;
3744 	/* Bit 0-15: FC */
3745 	/* Bit 16-31: DUR */
3746 	struct wmi_mac_addr i_addr1;
3747 	struct wmi_mac_addr i_addr2;
3748 	__le32 csa_ie[2];
3749 	__le32 xcsa_ie[2];
3750 	__le32 wb_ie[2];
3751 	__le32 cswarp_ie;
3752 	__le32 ies_present_flag; /* wmi_csa_event_ies_present_flag */
3753 } __packed;
3754 
3755 /* the definition of different PDEV parameters */
3756 #define PDEV_DEFAULT_STATS_UPDATE_PERIOD    500
3757 #define VDEV_DEFAULT_STATS_UPDATE_PERIOD    500
3758 #define PEER_DEFAULT_STATS_UPDATE_PERIOD    500
3759 
3760 struct wmi_pdev_param_map {
3761 	u32 tx_chain_mask;
3762 	u32 rx_chain_mask;
3763 	u32 txpower_limit2g;
3764 	u32 txpower_limit5g;
3765 	u32 txpower_scale;
3766 	u32 beacon_gen_mode;
3767 	u32 beacon_tx_mode;
3768 	u32 resmgr_offchan_mode;
3769 	u32 protection_mode;
3770 	u32 dynamic_bw;
3771 	u32 non_agg_sw_retry_th;
3772 	u32 agg_sw_retry_th;
3773 	u32 sta_kickout_th;
3774 	u32 ac_aggrsize_scaling;
3775 	u32 ltr_enable;
3776 	u32 ltr_ac_latency_be;
3777 	u32 ltr_ac_latency_bk;
3778 	u32 ltr_ac_latency_vi;
3779 	u32 ltr_ac_latency_vo;
3780 	u32 ltr_ac_latency_timeout;
3781 	u32 ltr_sleep_override;
3782 	u32 ltr_rx_override;
3783 	u32 ltr_tx_activity_timeout;
3784 	u32 l1ss_enable;
3785 	u32 dsleep_enable;
3786 	u32 pcielp_txbuf_flush;
3787 	u32 pcielp_txbuf_watermark;
3788 	u32 pcielp_txbuf_tmo_en;
3789 	u32 pcielp_txbuf_tmo_value;
3790 	u32 pdev_stats_update_period;
3791 	u32 vdev_stats_update_period;
3792 	u32 peer_stats_update_period;
3793 	u32 bcnflt_stats_update_period;
3794 	u32 pmf_qos;
3795 	u32 arp_ac_override;
3796 	u32 dcs;
3797 	u32 ani_enable;
3798 	u32 ani_poll_period;
3799 	u32 ani_listen_period;
3800 	u32 ani_ofdm_level;
3801 	u32 ani_cck_level;
3802 	u32 dyntxchain;
3803 	u32 proxy_sta;
3804 	u32 idle_ps_config;
3805 	u32 power_gating_sleep;
3806 	u32 fast_channel_reset;
3807 	u32 burst_dur;
3808 	u32 burst_enable;
3809 	u32 cal_period;
3810 	u32 aggr_burst;
3811 	u32 rx_decap_mode;
3812 	u32 smart_antenna_default_antenna;
3813 	u32 igmpmld_override;
3814 	u32 igmpmld_tid;
3815 	u32 antenna_gain;
3816 	u32 rx_filter;
3817 	u32 set_mcast_to_ucast_tid;
3818 	u32 proxy_sta_mode;
3819 	u32 set_mcast2ucast_mode;
3820 	u32 set_mcast2ucast_buffer;
3821 	u32 remove_mcast2ucast_buffer;
3822 	u32 peer_sta_ps_statechg_enable;
3823 	u32 igmpmld_ac_override;
3824 	u32 block_interbss;
3825 	u32 set_disable_reset_cmdid;
3826 	u32 set_msdu_ttl_cmdid;
3827 	u32 set_ppdu_duration_cmdid;
3828 	u32 txbf_sound_period_cmdid;
3829 	u32 set_promisc_mode_cmdid;
3830 	u32 set_burst_mode_cmdid;
3831 	u32 en_stats;
3832 	u32 mu_group_policy;
3833 	u32 noise_detection;
3834 	u32 noise_threshold;
3835 	u32 dpd_enable;
3836 	u32 set_mcast_bcast_echo;
3837 	u32 atf_strict_sch;
3838 	u32 atf_sched_duration;
3839 	u32 ant_plzn;
3840 	u32 mgmt_retry_limit;
3841 	u32 sensitivity_level;
3842 	u32 signed_txpower_2g;
3843 	u32 signed_txpower_5g;
3844 	u32 enable_per_tid_amsdu;
3845 	u32 enable_per_tid_ampdu;
3846 	u32 cca_threshold;
3847 	u32 rts_fixed_rate;
3848 	u32 pdev_reset;
3849 	u32 wapi_mbssid_offset;
3850 	u32 arp_srcaddr;
3851 	u32 arp_dstaddr;
3852 	u32 enable_btcoex;
3853 	u32 rfkill_config;
3854 	u32 rfkill_enable;
3855 	u32 peer_stats_info_enable;
3856 };
3857 
3858 #define WMI_PDEV_PARAM_UNSUPPORTED 0
3859 
3860 enum wmi_pdev_param {
3861 	/* TX chain mask */
3862 	WMI_PDEV_PARAM_TX_CHAIN_MASK = 0x1,
3863 	/* RX chain mask */
3864 	WMI_PDEV_PARAM_RX_CHAIN_MASK,
3865 	/* TX power limit for 2G Radio */
3866 	WMI_PDEV_PARAM_TXPOWER_LIMIT2G,
3867 	/* TX power limit for 5G Radio */
3868 	WMI_PDEV_PARAM_TXPOWER_LIMIT5G,
3869 	/* TX power scale */
3870 	WMI_PDEV_PARAM_TXPOWER_SCALE,
3871 	/* Beacon generation mode . 0: host, 1: target   */
3872 	WMI_PDEV_PARAM_BEACON_GEN_MODE,
3873 	/* Beacon generation mode . 0: staggered 1: bursted   */
3874 	WMI_PDEV_PARAM_BEACON_TX_MODE,
3875 	/*
3876 	 * Resource manager off chan mode .
3877 	 * 0: turn off offchan mode. 1: turn on offchan mode
3878 	 */
3879 	WMI_PDEV_PARAM_RESMGR_OFFCHAN_MODE,
3880 	/*
3881 	 * Protection mode:
3882 	 * 0: no protection 1:use CTS-to-self 2: use RTS/CTS
3883 	 */
3884 	WMI_PDEV_PARAM_PROTECTION_MODE,
3885 	/*
3886 	 * Dynamic bandwidth - 0: disable, 1: enable
3887 	 *
3888 	 * When enabled HW rate control tries different bandwidths when
3889 	 * retransmitting frames.
3890 	 */
3891 	WMI_PDEV_PARAM_DYNAMIC_BW,
3892 	/* Non aggregate/ 11g sw retry threshold.0-disable */
3893 	WMI_PDEV_PARAM_NON_AGG_SW_RETRY_TH,
3894 	/* aggregate sw retry threshold. 0-disable*/
3895 	WMI_PDEV_PARAM_AGG_SW_RETRY_TH,
3896 	/* Station kickout threshold (non of consecutive failures).0-disable */
3897 	WMI_PDEV_PARAM_STA_KICKOUT_TH,
3898 	/* Aggerate size scaling configuration per AC */
3899 	WMI_PDEV_PARAM_AC_AGGRSIZE_SCALING,
3900 	/* LTR enable */
3901 	WMI_PDEV_PARAM_LTR_ENABLE,
3902 	/* LTR latency for BE, in us */
3903 	WMI_PDEV_PARAM_LTR_AC_LATENCY_BE,
3904 	/* LTR latency for BK, in us */
3905 	WMI_PDEV_PARAM_LTR_AC_LATENCY_BK,
3906 	/* LTR latency for VI, in us */
3907 	WMI_PDEV_PARAM_LTR_AC_LATENCY_VI,
3908 	/* LTR latency for VO, in us  */
3909 	WMI_PDEV_PARAM_LTR_AC_LATENCY_VO,
3910 	/* LTR AC latency timeout, in ms */
3911 	WMI_PDEV_PARAM_LTR_AC_LATENCY_TIMEOUT,
3912 	/* LTR platform latency override, in us */
3913 	WMI_PDEV_PARAM_LTR_SLEEP_OVERRIDE,
3914 	/* LTR-RX override, in us */
3915 	WMI_PDEV_PARAM_LTR_RX_OVERRIDE,
3916 	/* Tx activity timeout for LTR, in us */
3917 	WMI_PDEV_PARAM_LTR_TX_ACTIVITY_TIMEOUT,
3918 	/* L1SS state machine enable */
3919 	WMI_PDEV_PARAM_L1SS_ENABLE,
3920 	/* Deep sleep state machine enable */
3921 	WMI_PDEV_PARAM_DSLEEP_ENABLE,
3922 	/* RX buffering flush enable */
3923 	WMI_PDEV_PARAM_PCIELP_TXBUF_FLUSH,
3924 	/* RX buffering matermark */
3925 	WMI_PDEV_PARAM_PCIELP_TXBUF_WATERMARK,
3926 	/* RX buffering timeout enable */
3927 	WMI_PDEV_PARAM_PCIELP_TXBUF_TMO_EN,
3928 	/* RX buffering timeout value */
3929 	WMI_PDEV_PARAM_PCIELP_TXBUF_TMO_VALUE,
3930 	/* pdev level stats update period in ms */
3931 	WMI_PDEV_PARAM_PDEV_STATS_UPDATE_PERIOD,
3932 	/* vdev level stats update period in ms */
3933 	WMI_PDEV_PARAM_VDEV_STATS_UPDATE_PERIOD,
3934 	/* peer level stats update period in ms */
3935 	WMI_PDEV_PARAM_PEER_STATS_UPDATE_PERIOD,
3936 	/* beacon filter status update period */
3937 	WMI_PDEV_PARAM_BCNFLT_STATS_UPDATE_PERIOD,
3938 	/* QOS Mgmt frame protection MFP/PMF 0: disable, 1: enable */
3939 	WMI_PDEV_PARAM_PMF_QOS,
3940 	/* Access category on which ARP frames are sent */
3941 	WMI_PDEV_PARAM_ARP_AC_OVERRIDE,
3942 	/* DCS configuration */
3943 	WMI_PDEV_PARAM_DCS,
3944 	/* Enable/Disable ANI on target */
3945 	WMI_PDEV_PARAM_ANI_ENABLE,
3946 	/* configure the ANI polling period */
3947 	WMI_PDEV_PARAM_ANI_POLL_PERIOD,
3948 	/* configure the ANI listening period */
3949 	WMI_PDEV_PARAM_ANI_LISTEN_PERIOD,
3950 	/* configure OFDM immunity level */
3951 	WMI_PDEV_PARAM_ANI_OFDM_LEVEL,
3952 	/* configure CCK immunity level */
3953 	WMI_PDEV_PARAM_ANI_CCK_LEVEL,
3954 	/* Enable/Disable CDD for 1x1 STAs in rate control module */
3955 	WMI_PDEV_PARAM_DYNTXCHAIN,
3956 	/* Enable/Disable proxy STA */
3957 	WMI_PDEV_PARAM_PROXY_STA,
3958 	/* Enable/Disable low power state when all VDEVs are inactive/idle. */
3959 	WMI_PDEV_PARAM_IDLE_PS_CONFIG,
3960 	/* Enable/Disable power gating sleep */
3961 	WMI_PDEV_PARAM_POWER_GATING_SLEEP,
3962 };
3963 
3964 enum wmi_10x_pdev_param {
3965 	/* TX chian mask */
3966 	WMI_10X_PDEV_PARAM_TX_CHAIN_MASK = 0x1,
3967 	/* RX chian mask */
3968 	WMI_10X_PDEV_PARAM_RX_CHAIN_MASK,
3969 	/* TX power limit for 2G Radio */
3970 	WMI_10X_PDEV_PARAM_TXPOWER_LIMIT2G,
3971 	/* TX power limit for 5G Radio */
3972 	WMI_10X_PDEV_PARAM_TXPOWER_LIMIT5G,
3973 	/* TX power scale */
3974 	WMI_10X_PDEV_PARAM_TXPOWER_SCALE,
3975 	/* Beacon generation mode . 0: host, 1: target   */
3976 	WMI_10X_PDEV_PARAM_BEACON_GEN_MODE,
3977 	/* Beacon generation mode . 0: staggered 1: bursted   */
3978 	WMI_10X_PDEV_PARAM_BEACON_TX_MODE,
3979 	/*
3980 	 * Resource manager off chan mode .
3981 	 * 0: turn off offchan mode. 1: turn on offchan mode
3982 	 */
3983 	WMI_10X_PDEV_PARAM_RESMGR_OFFCHAN_MODE,
3984 	/*
3985 	 * Protection mode:
3986 	 * 0: no protection 1:use CTS-to-self 2: use RTS/CTS
3987 	 */
3988 	WMI_10X_PDEV_PARAM_PROTECTION_MODE,
3989 	/* Dynamic bandwidth 0: disable 1: enable */
3990 	WMI_10X_PDEV_PARAM_DYNAMIC_BW,
3991 	/* Non aggregate/ 11g sw retry threshold.0-disable */
3992 	WMI_10X_PDEV_PARAM_NON_AGG_SW_RETRY_TH,
3993 	/* aggregate sw retry threshold. 0-disable*/
3994 	WMI_10X_PDEV_PARAM_AGG_SW_RETRY_TH,
3995 	/* Station kickout threshold (non of consecutive failures).0-disable */
3996 	WMI_10X_PDEV_PARAM_STA_KICKOUT_TH,
3997 	/* Aggerate size scaling configuration per AC */
3998 	WMI_10X_PDEV_PARAM_AC_AGGRSIZE_SCALING,
3999 	/* LTR enable */
4000 	WMI_10X_PDEV_PARAM_LTR_ENABLE,
4001 	/* LTR latency for BE, in us */
4002 	WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_BE,
4003 	/* LTR latency for BK, in us */
4004 	WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_BK,
4005 	/* LTR latency for VI, in us */
4006 	WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_VI,
4007 	/* LTR latency for VO, in us  */
4008 	WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_VO,
4009 	/* LTR AC latency timeout, in ms */
4010 	WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_TIMEOUT,
4011 	/* LTR platform latency override, in us */
4012 	WMI_10X_PDEV_PARAM_LTR_SLEEP_OVERRIDE,
4013 	/* LTR-RX override, in us */
4014 	WMI_10X_PDEV_PARAM_LTR_RX_OVERRIDE,
4015 	/* Tx activity timeout for LTR, in us */
4016 	WMI_10X_PDEV_PARAM_LTR_TX_ACTIVITY_TIMEOUT,
4017 	/* L1SS state machine enable */
4018 	WMI_10X_PDEV_PARAM_L1SS_ENABLE,
4019 	/* Deep sleep state machine enable */
4020 	WMI_10X_PDEV_PARAM_DSLEEP_ENABLE,
4021 	/* pdev level stats update period in ms */
4022 	WMI_10X_PDEV_PARAM_PDEV_STATS_UPDATE_PERIOD,
4023 	/* vdev level stats update period in ms */
4024 	WMI_10X_PDEV_PARAM_VDEV_STATS_UPDATE_PERIOD,
4025 	/* peer level stats update period in ms */
4026 	WMI_10X_PDEV_PARAM_PEER_STATS_UPDATE_PERIOD,
4027 	/* beacon filter status update period */
4028 	WMI_10X_PDEV_PARAM_BCNFLT_STATS_UPDATE_PERIOD,
4029 	/* QOS Mgmt frame protection MFP/PMF 0: disable, 1: enable */
4030 	WMI_10X_PDEV_PARAM_PMF_QOS,
4031 	/* Access category on which ARP and DHCP frames are sent */
4032 	WMI_10X_PDEV_PARAM_ARPDHCP_AC_OVERRIDE,
4033 	/* DCS configuration */
4034 	WMI_10X_PDEV_PARAM_DCS,
4035 	/* Enable/Disable ANI on target */
4036 	WMI_10X_PDEV_PARAM_ANI_ENABLE,
4037 	/* configure the ANI polling period */
4038 	WMI_10X_PDEV_PARAM_ANI_POLL_PERIOD,
4039 	/* configure the ANI listening period */
4040 	WMI_10X_PDEV_PARAM_ANI_LISTEN_PERIOD,
4041 	/* configure OFDM immunity level */
4042 	WMI_10X_PDEV_PARAM_ANI_OFDM_LEVEL,
4043 	/* configure CCK immunity level */
4044 	WMI_10X_PDEV_PARAM_ANI_CCK_LEVEL,
4045 	/* Enable/Disable CDD for 1x1 STAs in rate control module */
4046 	WMI_10X_PDEV_PARAM_DYNTXCHAIN,
4047 	/* Enable/Disable Fast channel reset*/
4048 	WMI_10X_PDEV_PARAM_FAST_CHANNEL_RESET,
4049 	/* Set Bursting DUR */
4050 	WMI_10X_PDEV_PARAM_BURST_DUR,
4051 	/* Set Bursting Enable*/
4052 	WMI_10X_PDEV_PARAM_BURST_ENABLE,
4053 
4054 	/* following are available as of firmware 10.2 */
4055 	WMI_10X_PDEV_PARAM_SMART_ANTENNA_DEFAULT_ANTENNA,
4056 	WMI_10X_PDEV_PARAM_IGMPMLD_OVERRIDE,
4057 	WMI_10X_PDEV_PARAM_IGMPMLD_TID,
4058 	WMI_10X_PDEV_PARAM_ANTENNA_GAIN,
4059 	WMI_10X_PDEV_PARAM_RX_DECAP_MODE,
4060 	WMI_10X_PDEV_PARAM_RX_FILTER,
4061 	WMI_10X_PDEV_PARAM_SET_MCAST_TO_UCAST_TID,
4062 	WMI_10X_PDEV_PARAM_PROXY_STA_MODE,
4063 	WMI_10X_PDEV_PARAM_SET_MCAST2UCAST_MODE,
4064 	WMI_10X_PDEV_PARAM_SET_MCAST2UCAST_BUFFER,
4065 	WMI_10X_PDEV_PARAM_REMOVE_MCAST2UCAST_BUFFER,
4066 	WMI_10X_PDEV_PARAM_PEER_STA_PS_STATECHG_ENABLE,
4067 	WMI_10X_PDEV_PARAM_RTS_FIXED_RATE,
4068 	WMI_10X_PDEV_PARAM_CAL_PERIOD,
4069 	WMI_10X_PDEV_PARAM_ATF_STRICT_SCH,
4070 	WMI_10X_PDEV_PARAM_ATF_SCHED_DURATION,
4071 	WMI_10X_PDEV_PARAM_SET_PROMISC_MODE_CMDID,
4072 	WMI_10X_PDEV_PARAM_PDEV_RESET
4073 };
4074 
4075 enum wmi_10_4_pdev_param {
4076 	WMI_10_4_PDEV_PARAM_TX_CHAIN_MASK = 0x1,
4077 	WMI_10_4_PDEV_PARAM_RX_CHAIN_MASK,
4078 	WMI_10_4_PDEV_PARAM_TXPOWER_LIMIT2G,
4079 	WMI_10_4_PDEV_PARAM_TXPOWER_LIMIT5G,
4080 	WMI_10_4_PDEV_PARAM_TXPOWER_SCALE,
4081 	WMI_10_4_PDEV_PARAM_BEACON_GEN_MODE,
4082 	WMI_10_4_PDEV_PARAM_BEACON_TX_MODE,
4083 	WMI_10_4_PDEV_PARAM_RESMGR_OFFCHAN_MODE,
4084 	WMI_10_4_PDEV_PARAM_PROTECTION_MODE,
4085 	WMI_10_4_PDEV_PARAM_DYNAMIC_BW,
4086 	WMI_10_4_PDEV_PARAM_NON_AGG_SW_RETRY_TH,
4087 	WMI_10_4_PDEV_PARAM_AGG_SW_RETRY_TH,
4088 	WMI_10_4_PDEV_PARAM_STA_KICKOUT_TH,
4089 	WMI_10_4_PDEV_PARAM_AC_AGGRSIZE_SCALING,
4090 	WMI_10_4_PDEV_PARAM_LTR_ENABLE,
4091 	WMI_10_4_PDEV_PARAM_LTR_AC_LATENCY_BE,
4092 	WMI_10_4_PDEV_PARAM_LTR_AC_LATENCY_BK,
4093 	WMI_10_4_PDEV_PARAM_LTR_AC_LATENCY_VI,
4094 	WMI_10_4_PDEV_PARAM_LTR_AC_LATENCY_VO,
4095 	WMI_10_4_PDEV_PARAM_LTR_AC_LATENCY_TIMEOUT,
4096 	WMI_10_4_PDEV_PARAM_LTR_SLEEP_OVERRIDE,
4097 	WMI_10_4_PDEV_PARAM_LTR_RX_OVERRIDE,
4098 	WMI_10_4_PDEV_PARAM_LTR_TX_ACTIVITY_TIMEOUT,
4099 	WMI_10_4_PDEV_PARAM_L1SS_ENABLE,
4100 	WMI_10_4_PDEV_PARAM_DSLEEP_ENABLE,
4101 	WMI_10_4_PDEV_PARAM_PCIELP_TXBUF_FLUSH,
4102 	WMI_10_4_PDEV_PARAM_PCIELP_TXBUF_WATERMARK,
4103 	WMI_10_4_PDEV_PARAM_PCIELP_TXBUF_TMO_EN,
4104 	WMI_10_4_PDEV_PARAM_PCIELP_TXBUF_TMO_VALUE,
4105 	WMI_10_4_PDEV_PARAM_PDEV_STATS_UPDATE_PERIOD,
4106 	WMI_10_4_PDEV_PARAM_VDEV_STATS_UPDATE_PERIOD,
4107 	WMI_10_4_PDEV_PARAM_PEER_STATS_UPDATE_PERIOD,
4108 	WMI_10_4_PDEV_PARAM_BCNFLT_STATS_UPDATE_PERIOD,
4109 	WMI_10_4_PDEV_PARAM_PMF_QOS,
4110 	WMI_10_4_PDEV_PARAM_ARP_AC_OVERRIDE,
4111 	WMI_10_4_PDEV_PARAM_DCS,
4112 	WMI_10_4_PDEV_PARAM_ANI_ENABLE,
4113 	WMI_10_4_PDEV_PARAM_ANI_POLL_PERIOD,
4114 	WMI_10_4_PDEV_PARAM_ANI_LISTEN_PERIOD,
4115 	WMI_10_4_PDEV_PARAM_ANI_OFDM_LEVEL,
4116 	WMI_10_4_PDEV_PARAM_ANI_CCK_LEVEL,
4117 	WMI_10_4_PDEV_PARAM_DYNTXCHAIN,
4118 	WMI_10_4_PDEV_PARAM_PROXY_STA,
4119 	WMI_10_4_PDEV_PARAM_IDLE_PS_CONFIG,
4120 	WMI_10_4_PDEV_PARAM_POWER_GATING_SLEEP,
4121 	WMI_10_4_PDEV_PARAM_AGGR_BURST,
4122 	WMI_10_4_PDEV_PARAM_RX_DECAP_MODE,
4123 	WMI_10_4_PDEV_PARAM_FAST_CHANNEL_RESET,
4124 	WMI_10_4_PDEV_PARAM_BURST_DUR,
4125 	WMI_10_4_PDEV_PARAM_BURST_ENABLE,
4126 	WMI_10_4_PDEV_PARAM_SMART_ANTENNA_DEFAULT_ANTENNA,
4127 	WMI_10_4_PDEV_PARAM_IGMPMLD_OVERRIDE,
4128 	WMI_10_4_PDEV_PARAM_IGMPMLD_TID,
4129 	WMI_10_4_PDEV_PARAM_ANTENNA_GAIN,
4130 	WMI_10_4_PDEV_PARAM_RX_FILTER,
4131 	WMI_10_4_PDEV_SET_MCAST_TO_UCAST_TID,
4132 	WMI_10_4_PDEV_PARAM_PROXY_STA_MODE,
4133 	WMI_10_4_PDEV_PARAM_SET_MCAST2UCAST_MODE,
4134 	WMI_10_4_PDEV_PARAM_SET_MCAST2UCAST_BUFFER,
4135 	WMI_10_4_PDEV_PARAM_REMOVE_MCAST2UCAST_BUFFER,
4136 	WMI_10_4_PDEV_PEER_STA_PS_STATECHG_ENABLE,
4137 	WMI_10_4_PDEV_PARAM_IGMPMLD_AC_OVERRIDE,
4138 	WMI_10_4_PDEV_PARAM_BLOCK_INTERBSS,
4139 	WMI_10_4_PDEV_PARAM_SET_DISABLE_RESET_CMDID,
4140 	WMI_10_4_PDEV_PARAM_SET_MSDU_TTL_CMDID,
4141 	WMI_10_4_PDEV_PARAM_SET_PPDU_DURATION_CMDID,
4142 	WMI_10_4_PDEV_PARAM_TXBF_SOUND_PERIOD_CMDID,
4143 	WMI_10_4_PDEV_PARAM_SET_PROMISC_MODE_CMDID,
4144 	WMI_10_4_PDEV_PARAM_SET_BURST_MODE_CMDID,
4145 	WMI_10_4_PDEV_PARAM_EN_STATS,
4146 	WMI_10_4_PDEV_PARAM_MU_GROUP_POLICY,
4147 	WMI_10_4_PDEV_PARAM_NOISE_DETECTION,
4148 	WMI_10_4_PDEV_PARAM_NOISE_THRESHOLD,
4149 	WMI_10_4_PDEV_PARAM_DPD_ENABLE,
4150 	WMI_10_4_PDEV_PARAM_SET_MCAST_BCAST_ECHO,
4151 	WMI_10_4_PDEV_PARAM_ATF_STRICT_SCH,
4152 	WMI_10_4_PDEV_PARAM_ATF_SCHED_DURATION,
4153 	WMI_10_4_PDEV_PARAM_ANT_PLZN,
4154 	WMI_10_4_PDEV_PARAM_MGMT_RETRY_LIMIT,
4155 	WMI_10_4_PDEV_PARAM_SENSITIVITY_LEVEL,
4156 	WMI_10_4_PDEV_PARAM_SIGNED_TXPOWER_2G,
4157 	WMI_10_4_PDEV_PARAM_SIGNED_TXPOWER_5G,
4158 	WMI_10_4_PDEV_PARAM_ENABLE_PER_TID_AMSDU,
4159 	WMI_10_4_PDEV_PARAM_ENABLE_PER_TID_AMPDU,
4160 	WMI_10_4_PDEV_PARAM_CCA_THRESHOLD,
4161 	WMI_10_4_PDEV_PARAM_RTS_FIXED_RATE,
4162 	WMI_10_4_PDEV_PARAM_CAL_PERIOD,
4163 	WMI_10_4_PDEV_PARAM_PDEV_RESET,
4164 	WMI_10_4_PDEV_PARAM_WAPI_MBSSID_OFFSET,
4165 	WMI_10_4_PDEV_PARAM_ARP_SRCADDR,
4166 	WMI_10_4_PDEV_PARAM_ARP_DSTADDR,
4167 	WMI_10_4_PDEV_PARAM_TXPOWER_DECR_DB,
4168 	WMI_10_4_PDEV_PARAM_RX_BATCHMODE,
4169 	WMI_10_4_PDEV_PARAM_PACKET_AGGR_DELAY,
4170 	WMI_10_4_PDEV_PARAM_ATF_OBSS_NOISE_SCH,
4171 	WMI_10_4_PDEV_PARAM_ATF_OBSS_NOISE_SCALING_FACTOR,
4172 	WMI_10_4_PDEV_PARAM_CUST_TXPOWER_SCALE,
4173 	WMI_10_4_PDEV_PARAM_ATF_DYNAMIC_ENABLE,
4174 	WMI_10_4_PDEV_PARAM_ATF_SSID_GROUP_POLICY,
4175 	WMI_10_4_PDEV_PARAM_ENABLE_BTCOEX,
4176 };
4177 
4178 struct wmi_pdev_set_param_cmd {
4179 	__le32 param_id;
4180 	__le32 param_value;
4181 } __packed;
4182 
4183 struct wmi_pdev_set_base_macaddr_cmd {
4184 	struct wmi_mac_addr mac_addr;
4185 } __packed;
4186 
4187 /* valid period is 1 ~ 60000ms, unit in millisecond */
4188 #define WMI_PDEV_PARAM_CAL_PERIOD_MAX 60000
4189 
4190 struct wmi_pdev_get_tpc_config_cmd {
4191 	/* parameter   */
4192 	__le32 param;
4193 } __packed;
4194 
4195 #define WMI_TPC_CONFIG_PARAM		1
4196 #define WMI_TPC_FINAL_RATE_MAX		240
4197 #define WMI_TPC_TX_N_CHAIN		4
4198 #define WMI_TPC_RATE_MAX               (WMI_TPC_TX_N_CHAIN * 65)
4199 #define WMI_TPC_PREAM_TABLE_MAX		10
4200 #define WMI_TPC_FLAG			3
4201 #define WMI_TPC_BUF_SIZE		10
4202 #define WMI_TPC_BEAMFORMING		2
4203 
4204 enum wmi_tpc_table_type {
4205 	WMI_TPC_TABLE_TYPE_CDD = 0,
4206 	WMI_TPC_TABLE_TYPE_STBC = 1,
4207 	WMI_TPC_TABLE_TYPE_TXBF = 2,
4208 };
4209 
4210 enum wmi_tpc_config_event_flag {
4211 	WMI_TPC_CONFIG_EVENT_FLAG_TABLE_CDD	= 0x1,
4212 	WMI_TPC_CONFIG_EVENT_FLAG_TABLE_STBC	= 0x2,
4213 	WMI_TPC_CONFIG_EVENT_FLAG_TABLE_TXBF	= 0x4,
4214 };
4215 
4216 struct wmi_pdev_tpc_config_event {
4217 	__le32 reg_domain;
4218 	__le32 chan_freq;
4219 	__le32 phy_mode;
4220 	__le32 twice_antenna_reduction;
4221 	__le32 twice_max_rd_power;
4222 	a_sle32 twice_antenna_gain;
4223 	__le32 power_limit;
4224 	__le32 rate_max;
4225 	__le32 num_tx_chain;
4226 	__le32 ctl;
4227 	__le32 flags;
4228 	s8 max_reg_allow_pow[WMI_TPC_TX_N_CHAIN];
4229 	s8 max_reg_allow_pow_agcdd[WMI_TPC_TX_N_CHAIN][WMI_TPC_TX_N_CHAIN];
4230 	s8 max_reg_allow_pow_agstbc[WMI_TPC_TX_N_CHAIN][WMI_TPC_TX_N_CHAIN];
4231 	s8 max_reg_allow_pow_agtxbf[WMI_TPC_TX_N_CHAIN][WMI_TPC_TX_N_CHAIN];
4232 	u8 rates_array[WMI_TPC_RATE_MAX];
4233 } __packed;
4234 
4235 /* Transmit power scale factor. */
4236 enum wmi_tp_scale {
4237 	WMI_TP_SCALE_MAX    = 0,	/* no scaling (default) */
4238 	WMI_TP_SCALE_50     = 1,	/* 50% of max (-3 dBm) */
4239 	WMI_TP_SCALE_25     = 2,	/* 25% of max (-6 dBm) */
4240 	WMI_TP_SCALE_12     = 3,	/* 12% of max (-9 dBm) */
4241 	WMI_TP_SCALE_MIN    = 4,	/* min, but still on   */
4242 	WMI_TP_SCALE_SIZE   = 5,	/* max num of enum     */
4243 };
4244 
4245 struct wmi_pdev_tpc_final_table_event {
4246 	__le32 reg_domain;
4247 	__le32 chan_freq;
4248 	__le32 phy_mode;
4249 	__le32 twice_antenna_reduction;
4250 	__le32 twice_max_rd_power;
4251 	a_sle32 twice_antenna_gain;
4252 	__le32 power_limit;
4253 	__le32 rate_max;
4254 	__le32 num_tx_chain;
4255 	__le32 ctl;
4256 	__le32 flags;
4257 	s8 max_reg_allow_pow[WMI_TPC_TX_N_CHAIN];
4258 	s8 max_reg_allow_pow_agcdd[WMI_TPC_TX_N_CHAIN][WMI_TPC_TX_N_CHAIN];
4259 	s8 max_reg_allow_pow_agstbc[WMI_TPC_TX_N_CHAIN][WMI_TPC_TX_N_CHAIN];
4260 	s8 max_reg_allow_pow_agtxbf[WMI_TPC_TX_N_CHAIN][WMI_TPC_TX_N_CHAIN];
4261 	u8 rates_array[WMI_TPC_FINAL_RATE_MAX];
4262 	u8 ctl_power_table[WMI_TPC_BEAMFORMING][WMI_TPC_TX_N_CHAIN]
4263 	   [WMI_TPC_TX_N_CHAIN];
4264 } __packed;
4265 
4266 struct wmi_pdev_get_tpc_table_cmd {
4267 	__le32 param;
4268 } __packed;
4269 
4270 enum wmi_tpc_pream_2ghz {
4271 	WMI_TPC_PREAM_2GHZ_CCK = 0,
4272 	WMI_TPC_PREAM_2GHZ_OFDM,
4273 	WMI_TPC_PREAM_2GHZ_HT20,
4274 	WMI_TPC_PREAM_2GHZ_HT40,
4275 	WMI_TPC_PREAM_2GHZ_VHT20,
4276 	WMI_TPC_PREAM_2GHZ_VHT40,
4277 	WMI_TPC_PREAM_2GHZ_VHT80,
4278 };
4279 
4280 enum wmi_tpc_pream_5ghz {
4281 	WMI_TPC_PREAM_5GHZ_OFDM = 1,
4282 	WMI_TPC_PREAM_5GHZ_HT20,
4283 	WMI_TPC_PREAM_5GHZ_HT40,
4284 	WMI_TPC_PREAM_5GHZ_VHT20,
4285 	WMI_TPC_PREAM_5GHZ_VHT40,
4286 	WMI_TPC_PREAM_5GHZ_VHT80,
4287 	WMI_TPC_PREAM_5GHZ_HTCUP,
4288 };
4289 
4290 #define	WMI_PEER_PS_STATE_DISABLED	2
4291 
4292 struct wmi_peer_sta_ps_state_chg_event {
4293 	struct wmi_mac_addr peer_macaddr;
4294 	__le32 peer_ps_state;
4295 } __packed;
4296 
4297 #define WMI_MAX_DEBUG_MESG (sizeof(u32) * 32)
4298 
4299 struct wmi_debug_mesg_event {
4300 	/* message buffer, NULL terminated */
4301 	char bufp[WMI_MAX_DEBUG_MESG];
4302 } __packed;
4303 
4304 enum {
4305 	/* P2P device */
4306 	VDEV_SUBTYPE_P2PDEV = 0,
4307 	/* P2P client */
4308 	VDEV_SUBTYPE_P2PCLI,
4309 	/* P2P GO */
4310 	VDEV_SUBTYPE_P2PGO,
4311 	/* BT3.0 HS */
4312 	VDEV_SUBTYPE_BT,
4313 };
4314 
4315 struct wmi_pdev_set_channel_cmd {
4316 	/* idnore power , only use flags , mode and freq */
4317 	struct wmi_channel chan;
4318 } __packed;
4319 
4320 struct wmi_pdev_pktlog_enable_cmd {
4321 	__le32 ev_bitmap;
4322 } __packed;
4323 
4324 /* Customize the DSCP (bit) to TID (0-7) mapping for QOS */
4325 #define WMI_DSCP_MAP_MAX    (64)
4326 struct wmi_pdev_set_dscp_tid_map_cmd {
4327 	/* map indicating DSCP to TID conversion */
4328 	__le32 dscp_to_tid_map[WMI_DSCP_MAP_MAX];
4329 } __packed;
4330 
4331 enum mcast_bcast_rate_id {
4332 	WMI_SET_MCAST_RATE,
4333 	WMI_SET_BCAST_RATE
4334 };
4335 
4336 struct mcast_bcast_rate {
4337 	enum mcast_bcast_rate_id rate_id;
4338 	__le32 rate;
4339 } __packed;
4340 
4341 struct wmi_wmm_params {
4342 	__le32 cwmin;
4343 	__le32 cwmax;
4344 	__le32 aifs;
4345 	__le32 txop;
4346 	__le32 acm;
4347 	__le32 no_ack;
4348 } __packed;
4349 
4350 struct wmi_pdev_set_wmm_params {
4351 	struct wmi_wmm_params ac_be;
4352 	struct wmi_wmm_params ac_bk;
4353 	struct wmi_wmm_params ac_vi;
4354 	struct wmi_wmm_params ac_vo;
4355 } __packed;
4356 
4357 struct wmi_wmm_params_arg {
4358 	u32 cwmin;
4359 	u32 cwmax;
4360 	u32 aifs;
4361 	u32 txop;
4362 	u32 acm;
4363 	u32 no_ack;
4364 };
4365 
4366 struct wmi_wmm_params_all_arg {
4367 	struct wmi_wmm_params_arg ac_be;
4368 	struct wmi_wmm_params_arg ac_bk;
4369 	struct wmi_wmm_params_arg ac_vi;
4370 	struct wmi_wmm_params_arg ac_vo;
4371 };
4372 
4373 struct wmi_pdev_stats_tx {
4374 	/* Num HTT cookies queued to dispatch list */
4375 	__le32 comp_queued;
4376 
4377 	/* Num HTT cookies dispatched */
4378 	__le32 comp_delivered;
4379 
4380 	/* Num MSDU queued to WAL */
4381 	__le32 msdu_enqued;
4382 
4383 	/* Num MPDU queue to WAL */
4384 	__le32 mpdu_enqued;
4385 
4386 	/* Num MSDUs dropped by WMM limit */
4387 	__le32 wmm_drop;
4388 
4389 	/* Num Local frames queued */
4390 	__le32 local_enqued;
4391 
4392 	/* Num Local frames done */
4393 	__le32 local_freed;
4394 
4395 	/* Num queued to HW */
4396 	__le32 hw_queued;
4397 
4398 	/* Num PPDU reaped from HW */
4399 	__le32 hw_reaped;
4400 
4401 	/* Num underruns */
4402 	__le32 underrun;
4403 
4404 	/* Num PPDUs cleaned up in TX abort */
4405 	__le32 tx_abort;
4406 
4407 	/* Num MPDUs requeued by SW */
4408 	__le32 mpdus_requeued;
4409 
4410 	/* excessive retries */
4411 	__le32 tx_ko;
4412 
4413 	/* data hw rate code */
4414 	__le32 data_rc;
4415 
4416 	/* Scheduler self triggers */
4417 	__le32 self_triggers;
4418 
4419 	/* frames dropped due to excessive sw retries */
4420 	__le32 sw_retry_failure;
4421 
4422 	/* illegal rate phy errors  */
4423 	__le32 illgl_rate_phy_err;
4424 
4425 	/* wal pdev continuous xretry */
4426 	__le32 pdev_cont_xretry;
4427 
4428 	/* wal pdev continuous xretry */
4429 	__le32 pdev_tx_timeout;
4430 
4431 	/* wal pdev resets  */
4432 	__le32 pdev_resets;
4433 
4434 	/* frames dropped due to non-availability of stateless TIDs */
4435 	__le32 stateless_tid_alloc_failure;
4436 
4437 	__le32 phy_underrun;
4438 
4439 	/* MPDU is more than txop limit */
4440 	__le32 txop_ovf;
4441 } __packed;
4442 
4443 struct wmi_10_4_pdev_stats_tx {
4444 	/* Num HTT cookies queued to dispatch list */
4445 	__le32 comp_queued;
4446 
4447 	/* Num HTT cookies dispatched */
4448 	__le32 comp_delivered;
4449 
4450 	/* Num MSDU queued to WAL */
4451 	__le32 msdu_enqued;
4452 
4453 	/* Num MPDU queue to WAL */
4454 	__le32 mpdu_enqued;
4455 
4456 	/* Num MSDUs dropped by WMM limit */
4457 	__le32 wmm_drop;
4458 
4459 	/* Num Local frames queued */
4460 	__le32 local_enqued;
4461 
4462 	/* Num Local frames done */
4463 	__le32 local_freed;
4464 
4465 	/* Num queued to HW */
4466 	__le32 hw_queued;
4467 
4468 	/* Num PPDU reaped from HW */
4469 	__le32 hw_reaped;
4470 
4471 	/* Num underruns */
4472 	__le32 underrun;
4473 
4474 	/* HW Paused. */
4475 	__le32  hw_paused;
4476 
4477 	/* Num PPDUs cleaned up in TX abort */
4478 	__le32 tx_abort;
4479 
4480 	/* Num MPDUs requeued by SW */
4481 	__le32 mpdus_requeued;
4482 
4483 	/* excessive retries */
4484 	__le32 tx_ko;
4485 
4486 	/* data hw rate code */
4487 	__le32 data_rc;
4488 
4489 	/* Scheduler self triggers */
4490 	__le32 self_triggers;
4491 
4492 	/* frames dropped due to excessive sw retries */
4493 	__le32 sw_retry_failure;
4494 
4495 	/* illegal rate phy errors  */
4496 	__le32 illgl_rate_phy_err;
4497 
4498 	/* wal pdev continuous xretry */
4499 	__le32 pdev_cont_xretry;
4500 
4501 	/* wal pdev tx timeouts */
4502 	__le32 pdev_tx_timeout;
4503 
4504 	/* wal pdev resets  */
4505 	__le32 pdev_resets;
4506 
4507 	/* frames dropped due to non-availability of stateless TIDs */
4508 	__le32 stateless_tid_alloc_failure;
4509 
4510 	__le32 phy_underrun;
4511 
4512 	/* MPDU is more than txop limit */
4513 	__le32 txop_ovf;
4514 
4515 	/* Number of Sequences posted */
4516 	__le32 seq_posted;
4517 
4518 	/* Number of Sequences failed queueing */
4519 	__le32 seq_failed_queueing;
4520 
4521 	/* Number of Sequences completed */
4522 	__le32 seq_completed;
4523 
4524 	/* Number of Sequences restarted */
4525 	__le32 seq_restarted;
4526 
4527 	/* Number of MU Sequences posted */
4528 	__le32 mu_seq_posted;
4529 
4530 	/* Num MPDUs flushed by SW, HWPAUSED,SW TXABORT(Reset,channel change) */
4531 	__le32 mpdus_sw_flush;
4532 
4533 	/* Num MPDUs filtered by HW, all filter condition (TTL expired) */
4534 	__le32 mpdus_hw_filter;
4535 
4536 	/* Num MPDUs truncated by PDG
4537 	 * (TXOP, TBTT, PPDU_duration based on rate, dyn_bw)
4538 	 */
4539 	__le32 mpdus_truncated;
4540 
4541 	/* Num MPDUs that was tried but didn't receive ACK or BA */
4542 	__le32 mpdus_ack_failed;
4543 
4544 	/* Num MPDUs that was dropped due to expiry. */
4545 	__le32 mpdus_expired;
4546 } __packed;
4547 
4548 struct wmi_pdev_stats_rx {
4549 	/* Cnts any change in ring routing mid-ppdu */
4550 	__le32 mid_ppdu_route_change;
4551 
4552 	/* Total number of statuses processed */
4553 	__le32 status_rcvd;
4554 
4555 	/* Extra frags on rings 0-3 */
4556 	__le32 r0_frags;
4557 	__le32 r1_frags;
4558 	__le32 r2_frags;
4559 	__le32 r3_frags;
4560 
4561 	/* MSDUs / MPDUs delivered to HTT */
4562 	__le32 htt_msdus;
4563 	__le32 htt_mpdus;
4564 
4565 	/* MSDUs / MPDUs delivered to local stack */
4566 	__le32 loc_msdus;
4567 	__le32 loc_mpdus;
4568 
4569 	/* AMSDUs that have more MSDUs than the status ring size */
4570 	__le32 oversize_amsdu;
4571 
4572 	/* Number of PHY errors */
4573 	__le32 phy_errs;
4574 
4575 	/* Number of PHY errors drops */
4576 	__le32 phy_err_drop;
4577 
4578 	/* Number of mpdu errors - FCS, MIC, ENC etc. */
4579 	__le32 mpdu_errs;
4580 } __packed;
4581 
4582 struct wmi_pdev_stats_peer {
4583 	/* REMOVE THIS ONCE REAL PEER STAT COUNTERS ARE ADDED */
4584 	__le32 dummy;
4585 } __packed;
4586 
4587 enum wmi_stats_id {
4588 	WMI_STAT_PEER = BIT(0),
4589 	WMI_STAT_AP = BIT(1),
4590 	WMI_STAT_PDEV = BIT(2),
4591 	WMI_STAT_VDEV = BIT(3),
4592 	WMI_STAT_BCNFLT = BIT(4),
4593 	WMI_STAT_VDEV_RATE = BIT(5),
4594 };
4595 
4596 enum wmi_10_4_stats_id {
4597 	WMI_10_4_STAT_PEER		= BIT(0),
4598 	WMI_10_4_STAT_AP		= BIT(1),
4599 	WMI_10_4_STAT_INST		= BIT(2),
4600 	WMI_10_4_STAT_PEER_EXTD		= BIT(3),
4601 	WMI_10_4_STAT_VDEV_EXTD		= BIT(4),
4602 };
4603 
4604 enum wmi_tlv_stats_id {
4605 	WMI_TLV_STAT_PEER	= BIT(0),
4606 	WMI_TLV_STAT_AP		= BIT(1),
4607 	WMI_TLV_STAT_PDEV	= BIT(2),
4608 	WMI_TLV_STAT_VDEV	= BIT(3),
4609 	WMI_TLV_STAT_PEER_EXTD  = BIT(10),
4610 };
4611 
4612 struct wlan_inst_rssi_args {
4613 	__le16 cfg_retry_count;
4614 	__le16 retry_count;
4615 };
4616 
4617 struct wmi_request_stats_cmd {
4618 	__le32 stats_id;
4619 
4620 	__le32 vdev_id;
4621 
4622 	/* peer MAC address */
4623 	struct wmi_mac_addr peer_macaddr;
4624 
4625 	/* Instantaneous RSSI arguments */
4626 	struct wlan_inst_rssi_args inst_rssi_args;
4627 } __packed;
4628 
4629 enum wmi_peer_stats_info_request_type {
4630 	/* request stats of one specified peer */
4631 	WMI_REQUEST_ONE_PEER_STATS_INFO = 0x01,
4632 	/* request stats of all peers belong to specified VDEV */
4633 	WMI_REQUEST_VDEV_ALL_PEER_STATS_INFO = 0x02,
4634 };
4635 
4636 /* Suspend option */
4637 enum {
4638 	/* suspend */
4639 	WMI_PDEV_SUSPEND,
4640 
4641 	/* suspend and disable all interrupts */
4642 	WMI_PDEV_SUSPEND_AND_DISABLE_INTR,
4643 };
4644 
4645 struct wmi_pdev_suspend_cmd {
4646 	/* suspend option sent to target */
4647 	__le32 suspend_opt;
4648 } __packed;
4649 
4650 struct wmi_stats_event {
4651 	__le32 stats_id; /* WMI_STAT_ */
4652 	/*
4653 	 * number of pdev stats event structures
4654 	 * (wmi_pdev_stats) 0 or 1
4655 	 */
4656 	__le32 num_pdev_stats;
4657 	/*
4658 	 * number of vdev stats event structures
4659 	 * (wmi_vdev_stats) 0 or max vdevs
4660 	 */
4661 	__le32 num_vdev_stats;
4662 	/*
4663 	 * number of peer stats event structures
4664 	 * (wmi_peer_stats) 0 or max peers
4665 	 */
4666 	__le32 num_peer_stats;
4667 	__le32 num_bcnflt_stats;
4668 	/*
4669 	 * followed by
4670 	 *   num_pdev_stats * size of(struct wmi_pdev_stats)
4671 	 *   num_vdev_stats * size of(struct wmi_vdev_stats)
4672 	 *   num_peer_stats * size of(struct wmi_peer_stats)
4673 	 *
4674 	 *  By having a zero sized array, the pointer to data area
4675 	 *  becomes available without increasing the struct size
4676 	 */
4677 	u8 data[];
4678 } __packed;
4679 
4680 struct wmi_10_2_stats_event {
4681 	__le32 stats_id; /* %WMI_REQUEST_ */
4682 	__le32 num_pdev_stats;
4683 	__le32 num_pdev_ext_stats;
4684 	__le32 num_vdev_stats;
4685 	__le32 num_peer_stats;
4686 	__le32 num_bcnflt_stats;
4687 	u8 data[];
4688 } __packed;
4689 
4690 /*
4691  * PDEV statistics
4692  * TODO: add all PDEV stats here
4693  */
4694 struct wmi_pdev_stats_base {
4695 	__le32 chan_nf;
4696 	__le32 tx_frame_count; /* Cycles spent transmitting frames */
4697 	__le32 rx_frame_count; /* Cycles spent receiving frames */
4698 	__le32 rx_clear_count; /* Total channel busy time, evidently */
4699 	__le32 cycle_count; /* Total on-channel time */
4700 	__le32 phy_err_count;
4701 	__le32 chan_tx_pwr;
4702 } __packed;
4703 
4704 struct wmi_pdev_stats {
4705 	struct wmi_pdev_stats_base base;
4706 	struct wmi_pdev_stats_tx tx;
4707 	struct wmi_pdev_stats_rx rx;
4708 	struct wmi_pdev_stats_peer peer;
4709 } __packed;
4710 
4711 struct wmi_pdev_stats_extra {
4712 	__le32 ack_rx_bad;
4713 	__le32 rts_bad;
4714 	__le32 rts_good;
4715 	__le32 fcs_bad;
4716 	__le32 no_beacons;
4717 	__le32 mib_int_count;
4718 } __packed;
4719 
4720 struct wmi_10x_pdev_stats {
4721 	struct wmi_pdev_stats_base base;
4722 	struct wmi_pdev_stats_tx tx;
4723 	struct wmi_pdev_stats_rx rx;
4724 	struct wmi_pdev_stats_peer peer;
4725 	struct wmi_pdev_stats_extra extra;
4726 } __packed;
4727 
4728 struct wmi_pdev_stats_mem {
4729 	__le32 dram_free;
4730 	__le32 iram_free;
4731 } __packed;
4732 
4733 struct wmi_10_2_pdev_stats {
4734 	struct wmi_pdev_stats_base base;
4735 	struct wmi_pdev_stats_tx tx;
4736 	__le32 mc_drop;
4737 	struct wmi_pdev_stats_rx rx;
4738 	__le32 pdev_rx_timeout;
4739 	struct wmi_pdev_stats_mem mem;
4740 	struct wmi_pdev_stats_peer peer;
4741 	struct wmi_pdev_stats_extra extra;
4742 } __packed;
4743 
4744 struct wmi_10_4_pdev_stats {
4745 	struct wmi_pdev_stats_base base;
4746 	struct wmi_10_4_pdev_stats_tx tx;
4747 	struct wmi_pdev_stats_rx rx;
4748 	__le32 rx_ovfl_errs;
4749 	struct wmi_pdev_stats_mem mem;
4750 	__le32 sram_free_size;
4751 	struct wmi_pdev_stats_extra extra;
4752 } __packed;
4753 
4754 /*
4755  * VDEV statistics
4756  */
4757 
4758 #define WMI_VDEV_STATS_FTM_COUNT_VALID	BIT(31)
4759 #define WMI_VDEV_STATS_FTM_COUNT_LSB	0
4760 #define WMI_VDEV_STATS_FTM_COUNT_MASK	0x7fffffff
4761 
4762 struct wmi_vdev_stats {
4763 	__le32 vdev_id;
4764 } __packed;
4765 
4766 struct wmi_vdev_stats_extd {
4767 	__le32 vdev_id;
4768 	__le32 ppdu_aggr_cnt;
4769 	__le32 ppdu_noack;
4770 	__le32 mpdu_queued;
4771 	__le32 ppdu_nonaggr_cnt;
4772 	__le32 mpdu_sw_requeued;
4773 	__le32 mpdu_suc_retry;
4774 	__le32 mpdu_suc_multitry;
4775 	__le32 mpdu_fail_retry;
4776 	__le32 tx_ftm_suc;
4777 	__le32 tx_ftm_suc_retry;
4778 	__le32 tx_ftm_fail;
4779 	__le32 rx_ftmr_cnt;
4780 	__le32 rx_ftmr_dup_cnt;
4781 	__le32 rx_iftmr_cnt;
4782 	__le32 rx_iftmr_dup_cnt;
4783 	__le32 reserved[6];
4784 } __packed;
4785 
4786 /*
4787  * peer statistics.
4788  * TODO: add more stats
4789  */
4790 struct wmi_peer_stats {
4791 	struct wmi_mac_addr peer_macaddr;
4792 	__le32 peer_rssi;
4793 	__le32 peer_tx_rate;
4794 } __packed;
4795 
4796 struct wmi_10x_peer_stats {
4797 	struct wmi_peer_stats old;
4798 	__le32 peer_rx_rate;
4799 } __packed;
4800 
4801 struct wmi_10_2_peer_stats {
4802 	struct wmi_peer_stats old;
4803 	__le32 peer_rx_rate;
4804 	__le32 current_per;
4805 	__le32 retries;
4806 	__le32 tx_rate_count;
4807 	__le32 max_4ms_frame_len;
4808 	__le32 total_sub_frames;
4809 	__le32 tx_bytes;
4810 	__le32 num_pkt_loss_overflow[4];
4811 	__le32 num_pkt_loss_excess_retry[4];
4812 } __packed;
4813 
4814 struct wmi_10_2_4_peer_stats {
4815 	struct wmi_10_2_peer_stats common;
4816 	__le32 peer_rssi_changed;
4817 } __packed;
4818 
4819 struct wmi_10_2_4_ext_peer_stats {
4820 	struct wmi_10_2_peer_stats common;
4821 	__le32 peer_rssi_changed;
4822 	__le32 rx_duration;
4823 } __packed;
4824 
4825 struct wmi_10_4_peer_stats {
4826 	struct wmi_mac_addr peer_macaddr;
4827 	__le32 peer_rssi;
4828 	__le32 peer_rssi_seq_num;
4829 	__le32 peer_tx_rate;
4830 	__le32 peer_rx_rate;
4831 	__le32 current_per;
4832 	__le32 retries;
4833 	__le32 tx_rate_count;
4834 	__le32 max_4ms_frame_len;
4835 	__le32 total_sub_frames;
4836 	__le32 tx_bytes;
4837 	__le32 num_pkt_loss_overflow[4];
4838 	__le32 num_pkt_loss_excess_retry[4];
4839 	__le32 peer_rssi_changed;
4840 } __packed;
4841 
4842 struct wmi_10_4_peer_extd_stats {
4843 	struct wmi_mac_addr peer_macaddr;
4844 	__le32 inactive_time;
4845 	__le32 peer_chain_rssi;
4846 	__le32 rx_duration;
4847 	__le32 reserved[10];
4848 } __packed;
4849 
4850 struct wmi_10_4_bss_bcn_stats {
4851 	__le32 vdev_id;
4852 	__le32 bss_bcns_dropped;
4853 	__le32 bss_bcn_delivered;
4854 } __packed;
4855 
4856 struct wmi_10_4_bss_bcn_filter_stats {
4857 	__le32 bcns_dropped;
4858 	__le32 bcns_delivered;
4859 	__le32 active_filters;
4860 	struct wmi_10_4_bss_bcn_stats bss_stats;
4861 } __packed;
4862 
4863 struct wmi_10_2_pdev_ext_stats {
4864 	__le32 rx_rssi_comb;
4865 	__le32 rx_rssi[4];
4866 	__le32 rx_mcs[10];
4867 	__le32 tx_mcs[10];
4868 	__le32 ack_rssi;
4869 } __packed;
4870 
4871 struct wmi_vdev_create_cmd {
4872 	__le32 vdev_id;
4873 	__le32 vdev_type;
4874 	__le32 vdev_subtype;
4875 	struct wmi_mac_addr vdev_macaddr;
4876 } __packed;
4877 
4878 enum wmi_vdev_type {
4879 	WMI_VDEV_TYPE_AP      = 1,
4880 	WMI_VDEV_TYPE_STA     = 2,
4881 	WMI_VDEV_TYPE_IBSS    = 3,
4882 	WMI_VDEV_TYPE_MONITOR = 4,
4883 };
4884 
4885 enum wmi_vdev_subtype {
4886 	WMI_VDEV_SUBTYPE_NONE,
4887 	WMI_VDEV_SUBTYPE_P2P_DEVICE,
4888 	WMI_VDEV_SUBTYPE_P2P_CLIENT,
4889 	WMI_VDEV_SUBTYPE_P2P_GO,
4890 	WMI_VDEV_SUBTYPE_PROXY_STA,
4891 	WMI_VDEV_SUBTYPE_MESH_11S,
4892 	WMI_VDEV_SUBTYPE_MESH_NON_11S,
4893 };
4894 
4895 enum wmi_vdev_subtype_legacy {
4896 	WMI_VDEV_SUBTYPE_LEGACY_NONE      = 0,
4897 	WMI_VDEV_SUBTYPE_LEGACY_P2P_DEV   = 1,
4898 	WMI_VDEV_SUBTYPE_LEGACY_P2P_CLI   = 2,
4899 	WMI_VDEV_SUBTYPE_LEGACY_P2P_GO    = 3,
4900 	WMI_VDEV_SUBTYPE_LEGACY_PROXY_STA = 4,
4901 };
4902 
4903 enum wmi_vdev_subtype_10_2_4 {
4904 	WMI_VDEV_SUBTYPE_10_2_4_NONE      = 0,
4905 	WMI_VDEV_SUBTYPE_10_2_4_P2P_DEV   = 1,
4906 	WMI_VDEV_SUBTYPE_10_2_4_P2P_CLI   = 2,
4907 	WMI_VDEV_SUBTYPE_10_2_4_P2P_GO    = 3,
4908 	WMI_VDEV_SUBTYPE_10_2_4_PROXY_STA = 4,
4909 	WMI_VDEV_SUBTYPE_10_2_4_MESH_11S  = 5,
4910 };
4911 
4912 enum wmi_vdev_subtype_10_4 {
4913 	WMI_VDEV_SUBTYPE_10_4_NONE         = 0,
4914 	WMI_VDEV_SUBTYPE_10_4_P2P_DEV      = 1,
4915 	WMI_VDEV_SUBTYPE_10_4_P2P_CLI      = 2,
4916 	WMI_VDEV_SUBTYPE_10_4_P2P_GO       = 3,
4917 	WMI_VDEV_SUBTYPE_10_4_PROXY_STA    = 4,
4918 	WMI_VDEV_SUBTYPE_10_4_MESH_NON_11S = 5,
4919 	WMI_VDEV_SUBTYPE_10_4_MESH_11S     = 6,
4920 };
4921 
4922 /* values for vdev_subtype */
4923 
4924 /* values for vdev_start_request flags */
4925 /*
4926  * Indicates that AP VDEV uses hidden ssid. only valid for
4927  *  AP/GO
4928  */
4929 #define WMI_VDEV_START_HIDDEN_SSID  (1 << 0)
4930 /*
4931  * Indicates if robust management frame/management frame
4932  *  protection is enabled. For GO/AP vdevs, it indicates that
4933  *  it may support station/client associations with RMF enabled.
4934  *  For STA/client vdevs, it indicates that sta will
4935  *  associate with AP with RMF enabled.
4936  */
4937 #define WMI_VDEV_START_PMF_ENABLED  (1 << 1)
4938 
4939 struct wmi_p2p_noa_descriptor {
4940 	__le32 type_count; /* 255: continuous schedule, 0: reserved */
4941 	__le32 duration;  /* Absent period duration in micro seconds */
4942 	__le32 interval;   /* Absent period interval in micro seconds */
4943 	__le32 start_time; /* 32 bit tsf time when in starts */
4944 } __packed;
4945 
4946 struct wmi_vdev_start_request_cmd {
4947 	/* WMI channel */
4948 	struct wmi_channel chan;
4949 	/* unique id identifying the VDEV, generated by the caller */
4950 	__le32 vdev_id;
4951 	/* requestor id identifying the caller module */
4952 	__le32 requestor_id;
4953 	/* beacon interval from received beacon */
4954 	__le32 beacon_interval;
4955 	/* DTIM Period from the received beacon */
4956 	__le32 dtim_period;
4957 	/* Flags */
4958 	__le32 flags;
4959 	/* ssid field. Only valid for AP/GO/IBSS/BTAmp VDEV type. */
4960 	struct wmi_ssid ssid;
4961 	/* beacon/probe response xmit rate. Applicable for SoftAP. */
4962 	__le32 bcn_tx_rate;
4963 	/* beacon/probe response xmit power. Applicable for SoftAP. */
4964 	__le32 bcn_tx_power;
4965 	/* number of p2p NOA descriptor(s) from scan entry */
4966 	__le32 num_noa_descriptors;
4967 	/*
4968 	 * Disable H/W ack. This used by WMI_VDEV_RESTART_REQUEST_CMDID.
4969 	 * During CAC, Our HW shouldn't ack ditected frames
4970 	 */
4971 	__le32 disable_hw_ack;
4972 	/* actual p2p NOA descriptor from scan entry */
4973 	struct wmi_p2p_noa_descriptor noa_descriptors[2];
4974 } __packed;
4975 
4976 struct wmi_vdev_restart_request_cmd {
4977 	struct wmi_vdev_start_request_cmd vdev_start_request_cmd;
4978 } __packed;
4979 
4980 struct wmi_vdev_start_request_arg {
4981 	u32 vdev_id;
4982 	struct wmi_channel_arg channel;
4983 	u32 bcn_intval;
4984 	u32 dtim_period;
4985 	u8 *ssid;
4986 	u32 ssid_len;
4987 	u32 bcn_tx_rate;
4988 	u32 bcn_tx_power;
4989 	bool disable_hw_ack;
4990 	bool hidden_ssid;
4991 	bool pmf_enabled;
4992 };
4993 
4994 struct wmi_vdev_delete_cmd {
4995 	/* unique id identifying the VDEV, generated by the caller */
4996 	__le32 vdev_id;
4997 } __packed;
4998 
4999 struct wmi_vdev_up_cmd {
5000 	__le32 vdev_id;
5001 	__le32 vdev_assoc_id;
5002 	struct wmi_mac_addr vdev_bssid;
5003 } __packed;
5004 
5005 struct wmi_vdev_stop_cmd {
5006 	__le32 vdev_id;
5007 } __packed;
5008 
5009 struct wmi_vdev_down_cmd {
5010 	__le32 vdev_id;
5011 } __packed;
5012 
5013 struct wmi_vdev_standby_response_cmd {
5014 	/* unique id identifying the VDEV, generated by the caller */
5015 	__le32 vdev_id;
5016 } __packed;
5017 
5018 struct wmi_vdev_resume_response_cmd {
5019 	/* unique id identifying the VDEV, generated by the caller */
5020 	__le32 vdev_id;
5021 } __packed;
5022 
5023 struct wmi_vdev_set_param_cmd {
5024 	__le32 vdev_id;
5025 	__le32 param_id;
5026 	__le32 param_value;
5027 } __packed;
5028 
5029 #define WMI_MAX_KEY_INDEX   3
5030 #define WMI_MAX_KEY_LEN     32
5031 
5032 #define WMI_KEY_PAIRWISE 0x00
5033 #define WMI_KEY_GROUP    0x01
5034 #define WMI_KEY_TX_USAGE 0x02 /* default tx key - static wep */
5035 
5036 struct wmi_key_seq_counter {
5037 	__le32 key_seq_counter_l;
5038 	__le32 key_seq_counter_h;
5039 } __packed;
5040 
5041 enum wmi_cipher_suites {
5042 	WMI_CIPHER_NONE,
5043 	WMI_CIPHER_WEP,
5044 	WMI_CIPHER_TKIP,
5045 	WMI_CIPHER_AES_OCB,
5046 	WMI_CIPHER_AES_CCM,
5047 	WMI_CIPHER_WAPI,
5048 	WMI_CIPHER_CKIP,
5049 	WMI_CIPHER_AES_CMAC,
5050 	WMI_CIPHER_AES_GCM,
5051 };
5052 
5053 enum wmi_tlv_cipher_suites {
5054 	WMI_TLV_CIPHER_NONE,
5055 	WMI_TLV_CIPHER_WEP,
5056 	WMI_TLV_CIPHER_TKIP,
5057 	WMI_TLV_CIPHER_AES_OCB,
5058 	WMI_TLV_CIPHER_AES_CCM,
5059 	WMI_TLV_CIPHER_WAPI,
5060 	WMI_TLV_CIPHER_CKIP,
5061 	WMI_TLV_CIPHER_AES_CMAC,
5062 	WMI_TLV_CIPHER_ANY,
5063 	WMI_TLV_CIPHER_AES_GCM,
5064 };
5065 
5066 struct wmi_vdev_install_key_cmd {
5067 	__le32 vdev_id;
5068 	struct wmi_mac_addr peer_macaddr;
5069 	__le32 key_idx;
5070 	__le32 key_flags;
5071 	__le32 key_cipher; /* %WMI_CIPHER_ */
5072 	struct wmi_key_seq_counter key_rsc_counter;
5073 	struct wmi_key_seq_counter key_global_rsc_counter;
5074 	struct wmi_key_seq_counter key_tsc_counter;
5075 	u8 wpi_key_rsc_counter[16];
5076 	u8 wpi_key_tsc_counter[16];
5077 	__le32 key_len;
5078 	__le32 key_txmic_len;
5079 	__le32 key_rxmic_len;
5080 
5081 	/* contains key followed by tx mic followed by rx mic */
5082 	u8 key_data[];
5083 } __packed;
5084 
5085 struct wmi_vdev_install_key_arg {
5086 	u32 vdev_id;
5087 	const u8 *macaddr;
5088 	u32 key_idx;
5089 	u32 key_flags;
5090 	u32 key_cipher;
5091 	u32 key_len;
5092 	u32 key_txmic_len;
5093 	u32 key_rxmic_len;
5094 	const void *key_data;
5095 };
5096 
5097 /*
5098  * vdev fixed rate format:
5099  * - preamble - b7:b6 - see WMI_RATE_PREMABLE_
5100  * - nss      - b5:b4 - ss number (0 mean 1ss)
5101  * - rate_mcs - b3:b0 - as below
5102  *    CCK:  0 - 11Mbps, 1 - 5,5Mbps, 2 - 2Mbps, 3 - 1Mbps,
5103  *          4 - 11Mbps (s), 5 - 5,5Mbps (s), 6 - 2Mbps (s)
5104  *    OFDM: 0 - 48Mbps, 1 - 24Mbps, 2 - 12Mbps, 3 - 6Mbps,
5105  *          4 - 54Mbps, 5 - 36Mbps, 6 - 18Mbps, 7 - 9Mbps
5106  *    HT/VHT: MCS index
5107  */
5108 
5109 /* Preamble types to be used with VDEV fixed rate configuration */
5110 enum wmi_rate_preamble {
5111 	WMI_RATE_PREAMBLE_OFDM,
5112 	WMI_RATE_PREAMBLE_CCK,
5113 	WMI_RATE_PREAMBLE_HT,
5114 	WMI_RATE_PREAMBLE_VHT,
5115 };
5116 
5117 #define ATH10K_HW_NSS(rate)		(1 + (((rate) >> 4) & 0x3))
5118 #define ATH10K_HW_PREAMBLE(rate)	(((rate) >> 6) & 0x3)
5119 #define ATH10K_HW_MCS_RATE(rate)	((rate) & 0xf)
5120 #define ATH10K_HW_LEGACY_RATE(rate)	((rate) & 0x3f)
5121 #define ATH10K_HW_BW(flags)		(((flags) >> 3) & 0x3)
5122 #define ATH10K_HW_GI(flags)		(((flags) >> 5) & 0x1)
5123 #define ATH10K_HW_RATECODE(rate, nss, preamble) \
5124 	(((preamble) << 6) | ((nss) << 4) | (rate))
5125 #define ATH10K_HW_AMPDU(flags)		((flags) & 0x1)
5126 #define ATH10K_HW_BA_FAIL(flags)	(((flags) >> 1) & 0x3)
5127 #define ATH10K_FW_SKIPPED_RATE_CTRL(flags)	(((flags) >> 6) & 0x1)
5128 
5129 #define ATH10K_VHT_MCS_NUM	10
5130 #define ATH10K_BW_NUM		6
5131 #define ATH10K_NSS_NUM		4
5132 #define ATH10K_LEGACY_NUM	12
5133 #define ATH10K_GI_NUM		2
5134 #define ATH10K_HT_MCS_NUM	32
5135 #define ATH10K_RATE_TABLE_NUM	320
5136 #define ATH10K_RATE_INFO_FLAGS_SGI_BIT	2
5137 
5138 /* Value to disable fixed rate setting */
5139 #define WMI_FIXED_RATE_NONE    (0xff)
5140 
5141 struct wmi_peer_param_map {
5142 	u32 smps_state;
5143 	u32 ampdu;
5144 	u32 authorize;
5145 	u32 chan_width;
5146 	u32 nss;
5147 	u32 use_4addr;
5148 	u32 membership;
5149 	u32 use_fixed_power;
5150 	u32 user_pos;
5151 	u32 crit_proto_hint_enabled;
5152 	u32 tx_fail_cnt_thr;
5153 	u32 set_hw_retry_cts2s;
5154 	u32 ibss_atim_win_len;
5155 	u32 debug;
5156 	u32 phymode;
5157 	u32 dummy_var;
5158 };
5159 
5160 struct wmi_vdev_param_map {
5161 	u32 rts_threshold;
5162 	u32 fragmentation_threshold;
5163 	u32 beacon_interval;
5164 	u32 listen_interval;
5165 	u32 multicast_rate;
5166 	u32 mgmt_tx_rate;
5167 	u32 slot_time;
5168 	u32 preamble;
5169 	u32 swba_time;
5170 	u32 wmi_vdev_stats_update_period;
5171 	u32 wmi_vdev_pwrsave_ageout_time;
5172 	u32 wmi_vdev_host_swba_interval;
5173 	u32 dtim_period;
5174 	u32 wmi_vdev_oc_scheduler_air_time_limit;
5175 	u32 wds;
5176 	u32 atim_window;
5177 	u32 bmiss_count_max;
5178 	u32 bmiss_first_bcnt;
5179 	u32 bmiss_final_bcnt;
5180 	u32 feature_wmm;
5181 	u32 chwidth;
5182 	u32 chextoffset;
5183 	u32 disable_htprotection;
5184 	u32 sta_quickkickout;
5185 	u32 mgmt_rate;
5186 	u32 protection_mode;
5187 	u32 fixed_rate;
5188 	u32 sgi;
5189 	u32 ldpc;
5190 	u32 tx_stbc;
5191 	u32 rx_stbc;
5192 	u32 intra_bss_fwd;
5193 	u32 def_keyid;
5194 	u32 nss;
5195 	u32 bcast_data_rate;
5196 	u32 mcast_data_rate;
5197 	u32 mcast_indicate;
5198 	u32 dhcp_indicate;
5199 	u32 unknown_dest_indicate;
5200 	u32 ap_keepalive_min_idle_inactive_time_secs;
5201 	u32 ap_keepalive_max_idle_inactive_time_secs;
5202 	u32 ap_keepalive_max_unresponsive_time_secs;
5203 	u32 ap_enable_nawds;
5204 	u32 mcast2ucast_set;
5205 	u32 enable_rtscts;
5206 	u32 txbf;
5207 	u32 packet_powersave;
5208 	u32 drop_unencry;
5209 	u32 tx_encap_type;
5210 	u32 ap_detect_out_of_sync_sleeping_sta_time_secs;
5211 	u32 rc_num_retries;
5212 	u32 cabq_maxdur;
5213 	u32 mfptest_set;
5214 	u32 rts_fixed_rate;
5215 	u32 vht_sgimask;
5216 	u32 vht80_ratemask;
5217 	u32 early_rx_adjust_enable;
5218 	u32 early_rx_tgt_bmiss_num;
5219 	u32 early_rx_bmiss_sample_cycle;
5220 	u32 early_rx_slop_step;
5221 	u32 early_rx_init_slop;
5222 	u32 early_rx_adjust_pause;
5223 	u32 proxy_sta;
5224 	u32 meru_vc;
5225 	u32 rx_decap_type;
5226 	u32 bw_nss_ratemask;
5227 	u32 inc_tsf;
5228 	u32 dec_tsf;
5229 	u32 disable_4addr_src_lrn;
5230 	u32 rtt_responder_role;
5231 };
5232 
5233 #define WMI_VDEV_PARAM_UNSUPPORTED 0
5234 
5235 /* the definition of different VDEV parameters */
5236 enum wmi_vdev_param {
5237 	/* RTS Threshold */
5238 	WMI_VDEV_PARAM_RTS_THRESHOLD = 0x1,
5239 	/* Fragmentation threshold */
5240 	WMI_VDEV_PARAM_FRAGMENTATION_THRESHOLD,
5241 	/* beacon interval in TUs */
5242 	WMI_VDEV_PARAM_BEACON_INTERVAL,
5243 	/* Listen interval in TUs */
5244 	WMI_VDEV_PARAM_LISTEN_INTERVAL,
5245 	/* multicast rate in Mbps */
5246 	WMI_VDEV_PARAM_MULTICAST_RATE,
5247 	/* management frame rate in Mbps */
5248 	WMI_VDEV_PARAM_MGMT_TX_RATE,
5249 	/* slot time (long vs short) */
5250 	WMI_VDEV_PARAM_SLOT_TIME,
5251 	/* preamble (long vs short) */
5252 	WMI_VDEV_PARAM_PREAMBLE,
5253 	/* SWBA time (time before tbtt in msec) */
5254 	WMI_VDEV_PARAM_SWBA_TIME,
5255 	/* time period for updating VDEV stats */
5256 	WMI_VDEV_STATS_UPDATE_PERIOD,
5257 	/* age out time in msec for frames queued for station in power save */
5258 	WMI_VDEV_PWRSAVE_AGEOUT_TIME,
5259 	/*
5260 	 * Host SWBA interval (time in msec before tbtt for SWBA event
5261 	 * generation).
5262 	 */
5263 	WMI_VDEV_HOST_SWBA_INTERVAL,
5264 	/* DTIM period (specified in units of num beacon intervals) */
5265 	WMI_VDEV_PARAM_DTIM_PERIOD,
5266 	/*
5267 	 * scheduler air time limit for this VDEV. used by off chan
5268 	 * scheduler.
5269 	 */
5270 	WMI_VDEV_OC_SCHEDULER_AIR_TIME_LIMIT,
5271 	/* enable/disable WDS for this VDEV  */
5272 	WMI_VDEV_PARAM_WDS,
5273 	/* ATIM Window */
5274 	WMI_VDEV_PARAM_ATIM_WINDOW,
5275 	/* BMISS max */
5276 	WMI_VDEV_PARAM_BMISS_COUNT_MAX,
5277 	/* BMISS first time */
5278 	WMI_VDEV_PARAM_BMISS_FIRST_BCNT,
5279 	/* BMISS final time */
5280 	WMI_VDEV_PARAM_BMISS_FINAL_BCNT,
5281 	/* WMM enables/disabled */
5282 	WMI_VDEV_PARAM_FEATURE_WMM,
5283 	/* Channel width */
5284 	WMI_VDEV_PARAM_CHWIDTH,
5285 	/* Channel Offset */
5286 	WMI_VDEV_PARAM_CHEXTOFFSET,
5287 	/* Disable HT Protection */
5288 	WMI_VDEV_PARAM_DISABLE_HTPROTECTION,
5289 	/* Quick STA Kickout */
5290 	WMI_VDEV_PARAM_STA_QUICKKICKOUT,
5291 	/* Rate to be used with Management frames */
5292 	WMI_VDEV_PARAM_MGMT_RATE,
5293 	/* Protection Mode */
5294 	WMI_VDEV_PARAM_PROTECTION_MODE,
5295 	/* Fixed rate setting */
5296 	WMI_VDEV_PARAM_FIXED_RATE,
5297 	/* Short GI Enable/Disable */
5298 	WMI_VDEV_PARAM_SGI,
5299 	/* Enable LDPC */
5300 	WMI_VDEV_PARAM_LDPC,
5301 	/* Enable Tx STBC */
5302 	WMI_VDEV_PARAM_TX_STBC,
5303 	/* Enable Rx STBC */
5304 	WMI_VDEV_PARAM_RX_STBC,
5305 	/* Intra BSS forwarding  */
5306 	WMI_VDEV_PARAM_INTRA_BSS_FWD,
5307 	/* Setting Default xmit key for Vdev */
5308 	WMI_VDEV_PARAM_DEF_KEYID,
5309 	/* NSS width */
5310 	WMI_VDEV_PARAM_NSS,
5311 	/* Set the custom rate for the broadcast data frames */
5312 	WMI_VDEV_PARAM_BCAST_DATA_RATE,
5313 	/* Set the custom rate (rate-code) for multicast data frames */
5314 	WMI_VDEV_PARAM_MCAST_DATA_RATE,
5315 	/* Tx multicast packet indicate Enable/Disable */
5316 	WMI_VDEV_PARAM_MCAST_INDICATE,
5317 	/* Tx DHCP packet indicate Enable/Disable */
5318 	WMI_VDEV_PARAM_DHCP_INDICATE,
5319 	/* Enable host inspection of Tx unicast packet to unknown destination */
5320 	WMI_VDEV_PARAM_UNKNOWN_DEST_INDICATE,
5321 
5322 	/* The minimum amount of time AP begins to consider STA inactive */
5323 	WMI_VDEV_PARAM_AP_KEEPALIVE_MIN_IDLE_INACTIVE_TIME_SECS,
5324 
5325 	/*
5326 	 * An associated STA is considered inactive when there is no recent
5327 	 * TX/RX activity and no downlink frames are buffered for it. Once a
5328 	 * STA exceeds the maximum idle inactive time, the AP will send an
5329 	 * 802.11 data-null as a keep alive to verify the STA is still
5330 	 * associated. If the STA does ACK the data-null, or if the data-null
5331 	 * is buffered and the STA does not retrieve it, the STA will be
5332 	 * considered unresponsive
5333 	 * (see WMI_VDEV_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS).
5334 	 */
5335 	WMI_VDEV_PARAM_AP_KEEPALIVE_MAX_IDLE_INACTIVE_TIME_SECS,
5336 
5337 	/*
5338 	 * An associated STA is considered unresponsive if there is no recent
5339 	 * TX/RX activity and downlink frames are buffered for it. Once a STA
5340 	 * exceeds the maximum unresponsive time, the AP will send a
5341 	 * WMI_STA_KICKOUT event to the host so the STA can be deleted.
5342 	 */
5343 	WMI_VDEV_PARAM_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS,
5344 
5345 	/* Enable NAWDS : MCAST INSPECT Enable, NAWDS Flag set */
5346 	WMI_VDEV_PARAM_AP_ENABLE_NAWDS,
5347 	/* Enable/Disable RTS-CTS */
5348 	WMI_VDEV_PARAM_ENABLE_RTSCTS,
5349 	/* Enable TXBFee/er */
5350 	WMI_VDEV_PARAM_TXBF,
5351 
5352 	/* Set packet power save */
5353 	WMI_VDEV_PARAM_PACKET_POWERSAVE,
5354 
5355 	/*
5356 	 * Drops un-encrypted packets if eceived in an encrypted connection
5357 	 * otherwise forwards to host.
5358 	 */
5359 	WMI_VDEV_PARAM_DROP_UNENCRY,
5360 
5361 	/*
5362 	 * Set the encapsulation type for frames.
5363 	 */
5364 	WMI_VDEV_PARAM_TX_ENCAP_TYPE,
5365 };
5366 
5367 /* the definition of different VDEV parameters */
5368 enum wmi_10x_vdev_param {
5369 	/* RTS Threshold */
5370 	WMI_10X_VDEV_PARAM_RTS_THRESHOLD = 0x1,
5371 	/* Fragmentation threshold */
5372 	WMI_10X_VDEV_PARAM_FRAGMENTATION_THRESHOLD,
5373 	/* beacon interval in TUs */
5374 	WMI_10X_VDEV_PARAM_BEACON_INTERVAL,
5375 	/* Listen interval in TUs */
5376 	WMI_10X_VDEV_PARAM_LISTEN_INTERVAL,
5377 	/* multicast rate in Mbps */
5378 	WMI_10X_VDEV_PARAM_MULTICAST_RATE,
5379 	/* management frame rate in Mbps */
5380 	WMI_10X_VDEV_PARAM_MGMT_TX_RATE,
5381 	/* slot time (long vs short) */
5382 	WMI_10X_VDEV_PARAM_SLOT_TIME,
5383 	/* preamble (long vs short) */
5384 	WMI_10X_VDEV_PARAM_PREAMBLE,
5385 	/* SWBA time (time before tbtt in msec) */
5386 	WMI_10X_VDEV_PARAM_SWBA_TIME,
5387 	/* time period for updating VDEV stats */
5388 	WMI_10X_VDEV_STATS_UPDATE_PERIOD,
5389 	/* age out time in msec for frames queued for station in power save */
5390 	WMI_10X_VDEV_PWRSAVE_AGEOUT_TIME,
5391 	/*
5392 	 * Host SWBA interval (time in msec before tbtt for SWBA event
5393 	 * generation).
5394 	 */
5395 	WMI_10X_VDEV_HOST_SWBA_INTERVAL,
5396 	/* DTIM period (specified in units of num beacon intervals) */
5397 	WMI_10X_VDEV_PARAM_DTIM_PERIOD,
5398 	/*
5399 	 * scheduler air time limit for this VDEV. used by off chan
5400 	 * scheduler.
5401 	 */
5402 	WMI_10X_VDEV_OC_SCHEDULER_AIR_TIME_LIMIT,
5403 	/* enable/disable WDS for this VDEV  */
5404 	WMI_10X_VDEV_PARAM_WDS,
5405 	/* ATIM Window */
5406 	WMI_10X_VDEV_PARAM_ATIM_WINDOW,
5407 	/* BMISS max */
5408 	WMI_10X_VDEV_PARAM_BMISS_COUNT_MAX,
5409 	/* WMM enables/disabled */
5410 	WMI_10X_VDEV_PARAM_FEATURE_WMM,
5411 	/* Channel width */
5412 	WMI_10X_VDEV_PARAM_CHWIDTH,
5413 	/* Channel Offset */
5414 	WMI_10X_VDEV_PARAM_CHEXTOFFSET,
5415 	/* Disable HT Protection */
5416 	WMI_10X_VDEV_PARAM_DISABLE_HTPROTECTION,
5417 	/* Quick STA Kickout */
5418 	WMI_10X_VDEV_PARAM_STA_QUICKKICKOUT,
5419 	/* Rate to be used with Management frames */
5420 	WMI_10X_VDEV_PARAM_MGMT_RATE,
5421 	/* Protection Mode */
5422 	WMI_10X_VDEV_PARAM_PROTECTION_MODE,
5423 	/* Fixed rate setting */
5424 	WMI_10X_VDEV_PARAM_FIXED_RATE,
5425 	/* Short GI Enable/Disable */
5426 	WMI_10X_VDEV_PARAM_SGI,
5427 	/* Enable LDPC */
5428 	WMI_10X_VDEV_PARAM_LDPC,
5429 	/* Enable Tx STBC */
5430 	WMI_10X_VDEV_PARAM_TX_STBC,
5431 	/* Enable Rx STBC */
5432 	WMI_10X_VDEV_PARAM_RX_STBC,
5433 	/* Intra BSS forwarding  */
5434 	WMI_10X_VDEV_PARAM_INTRA_BSS_FWD,
5435 	/* Setting Default xmit key for Vdev */
5436 	WMI_10X_VDEV_PARAM_DEF_KEYID,
5437 	/* NSS width */
5438 	WMI_10X_VDEV_PARAM_NSS,
5439 	/* Set the custom rate for the broadcast data frames */
5440 	WMI_10X_VDEV_PARAM_BCAST_DATA_RATE,
5441 	/* Set the custom rate (rate-code) for multicast data frames */
5442 	WMI_10X_VDEV_PARAM_MCAST_DATA_RATE,
5443 	/* Tx multicast packet indicate Enable/Disable */
5444 	WMI_10X_VDEV_PARAM_MCAST_INDICATE,
5445 	/* Tx DHCP packet indicate Enable/Disable */
5446 	WMI_10X_VDEV_PARAM_DHCP_INDICATE,
5447 	/* Enable host inspection of Tx unicast packet to unknown destination */
5448 	WMI_10X_VDEV_PARAM_UNKNOWN_DEST_INDICATE,
5449 
5450 	/* The minimum amount of time AP begins to consider STA inactive */
5451 	WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MIN_IDLE_INACTIVE_TIME_SECS,
5452 
5453 	/*
5454 	 * An associated STA is considered inactive when there is no recent
5455 	 * TX/RX activity and no downlink frames are buffered for it. Once a
5456 	 * STA exceeds the maximum idle inactive time, the AP will send an
5457 	 * 802.11 data-null as a keep alive to verify the STA is still
5458 	 * associated. If the STA does ACK the data-null, or if the data-null
5459 	 * is buffered and the STA does not retrieve it, the STA will be
5460 	 * considered unresponsive
5461 	 * (see WMI_10X_VDEV_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS).
5462 	 */
5463 	WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MAX_IDLE_INACTIVE_TIME_SECS,
5464 
5465 	/*
5466 	 * An associated STA is considered unresponsive if there is no recent
5467 	 * TX/RX activity and downlink frames are buffered for it. Once a STA
5468 	 * exceeds the maximum unresponsive time, the AP will send a
5469 	 * WMI_10X_STA_KICKOUT event to the host so the STA can be deleted.
5470 	 */
5471 	WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS,
5472 
5473 	/* Enable NAWDS : MCAST INSPECT Enable, NAWDS Flag set */
5474 	WMI_10X_VDEV_PARAM_AP_ENABLE_NAWDS,
5475 
5476 	WMI_10X_VDEV_PARAM_MCAST2UCAST_SET,
5477 	/* Enable/Disable RTS-CTS */
5478 	WMI_10X_VDEV_PARAM_ENABLE_RTSCTS,
5479 
5480 	WMI_10X_VDEV_PARAM_AP_DETECT_OUT_OF_SYNC_SLEEPING_STA_TIME_SECS,
5481 
5482 	/* following are available as of firmware 10.2 */
5483 	WMI_10X_VDEV_PARAM_TX_ENCAP_TYPE,
5484 	WMI_10X_VDEV_PARAM_CABQ_MAXDUR,
5485 	WMI_10X_VDEV_PARAM_MFPTEST_SET,
5486 	WMI_10X_VDEV_PARAM_RTS_FIXED_RATE,
5487 	WMI_10X_VDEV_PARAM_VHT_SGIMASK,
5488 	WMI_10X_VDEV_PARAM_VHT80_RATEMASK,
5489 	WMI_10X_VDEV_PARAM_TSF_INCREMENT,
5490 };
5491 
5492 enum wmi_10_4_vdev_param {
5493 	WMI_10_4_VDEV_PARAM_RTS_THRESHOLD = 0x1,
5494 	WMI_10_4_VDEV_PARAM_FRAGMENTATION_THRESHOLD,
5495 	WMI_10_4_VDEV_PARAM_BEACON_INTERVAL,
5496 	WMI_10_4_VDEV_PARAM_LISTEN_INTERVAL,
5497 	WMI_10_4_VDEV_PARAM_MULTICAST_RATE,
5498 	WMI_10_4_VDEV_PARAM_MGMT_TX_RATE,
5499 	WMI_10_4_VDEV_PARAM_SLOT_TIME,
5500 	WMI_10_4_VDEV_PARAM_PREAMBLE,
5501 	WMI_10_4_VDEV_PARAM_SWBA_TIME,
5502 	WMI_10_4_VDEV_STATS_UPDATE_PERIOD,
5503 	WMI_10_4_VDEV_PWRSAVE_AGEOUT_TIME,
5504 	WMI_10_4_VDEV_HOST_SWBA_INTERVAL,
5505 	WMI_10_4_VDEV_PARAM_DTIM_PERIOD,
5506 	WMI_10_4_VDEV_OC_SCHEDULER_AIR_TIME_LIMIT,
5507 	WMI_10_4_VDEV_PARAM_WDS,
5508 	WMI_10_4_VDEV_PARAM_ATIM_WINDOW,
5509 	WMI_10_4_VDEV_PARAM_BMISS_COUNT_MAX,
5510 	WMI_10_4_VDEV_PARAM_BMISS_FIRST_BCNT,
5511 	WMI_10_4_VDEV_PARAM_BMISS_FINAL_BCNT,
5512 	WMI_10_4_VDEV_PARAM_FEATURE_WMM,
5513 	WMI_10_4_VDEV_PARAM_CHWIDTH,
5514 	WMI_10_4_VDEV_PARAM_CHEXTOFFSET,
5515 	WMI_10_4_VDEV_PARAM_DISABLE_HTPROTECTION,
5516 	WMI_10_4_VDEV_PARAM_STA_QUICKKICKOUT,
5517 	WMI_10_4_VDEV_PARAM_MGMT_RATE,
5518 	WMI_10_4_VDEV_PARAM_PROTECTION_MODE,
5519 	WMI_10_4_VDEV_PARAM_FIXED_RATE,
5520 	WMI_10_4_VDEV_PARAM_SGI,
5521 	WMI_10_4_VDEV_PARAM_LDPC,
5522 	WMI_10_4_VDEV_PARAM_TX_STBC,
5523 	WMI_10_4_VDEV_PARAM_RX_STBC,
5524 	WMI_10_4_VDEV_PARAM_INTRA_BSS_FWD,
5525 	WMI_10_4_VDEV_PARAM_DEF_KEYID,
5526 	WMI_10_4_VDEV_PARAM_NSS,
5527 	WMI_10_4_VDEV_PARAM_BCAST_DATA_RATE,
5528 	WMI_10_4_VDEV_PARAM_MCAST_DATA_RATE,
5529 	WMI_10_4_VDEV_PARAM_MCAST_INDICATE,
5530 	WMI_10_4_VDEV_PARAM_DHCP_INDICATE,
5531 	WMI_10_4_VDEV_PARAM_UNKNOWN_DEST_INDICATE,
5532 	WMI_10_4_VDEV_PARAM_AP_KEEPALIVE_MIN_IDLE_INACTIVE_TIME_SECS,
5533 	WMI_10_4_VDEV_PARAM_AP_KEEPALIVE_MAX_IDLE_INACTIVE_TIME_SECS,
5534 	WMI_10_4_VDEV_PARAM_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS,
5535 	WMI_10_4_VDEV_PARAM_AP_ENABLE_NAWDS,
5536 	WMI_10_4_VDEV_PARAM_MCAST2UCAST_SET,
5537 	WMI_10_4_VDEV_PARAM_ENABLE_RTSCTS,
5538 	WMI_10_4_VDEV_PARAM_RC_NUM_RETRIES,
5539 	WMI_10_4_VDEV_PARAM_TXBF,
5540 	WMI_10_4_VDEV_PARAM_PACKET_POWERSAVE,
5541 	WMI_10_4_VDEV_PARAM_DROP_UNENCRY,
5542 	WMI_10_4_VDEV_PARAM_TX_ENCAP_TYPE,
5543 	WMI_10_4_VDEV_PARAM_AP_DETECT_OUT_OF_SYNC_SLEEPING_STA_TIME_SECS,
5544 	WMI_10_4_VDEV_PARAM_CABQ_MAXDUR,
5545 	WMI_10_4_VDEV_PARAM_MFPTEST_SET,
5546 	WMI_10_4_VDEV_PARAM_RTS_FIXED_RATE,
5547 	WMI_10_4_VDEV_PARAM_VHT_SGIMASK,
5548 	WMI_10_4_VDEV_PARAM_VHT80_RATEMASK,
5549 	WMI_10_4_VDEV_PARAM_EARLY_RX_ADJUST_ENABLE,
5550 	WMI_10_4_VDEV_PARAM_EARLY_RX_TGT_BMISS_NUM,
5551 	WMI_10_4_VDEV_PARAM_EARLY_RX_BMISS_SAMPLE_CYCLE,
5552 	WMI_10_4_VDEV_PARAM_EARLY_RX_SLOP_STEP,
5553 	WMI_10_4_VDEV_PARAM_EARLY_RX_INIT_SLOP,
5554 	WMI_10_4_VDEV_PARAM_EARLY_RX_ADJUST_PAUSE,
5555 	WMI_10_4_VDEV_PARAM_PROXY_STA,
5556 	WMI_10_4_VDEV_PARAM_MERU_VC,
5557 	WMI_10_4_VDEV_PARAM_RX_DECAP_TYPE,
5558 	WMI_10_4_VDEV_PARAM_BW_NSS_RATEMASK,
5559 	WMI_10_4_VDEV_PARAM_SENSOR_AP,
5560 	WMI_10_4_VDEV_PARAM_BEACON_RATE,
5561 	WMI_10_4_VDEV_PARAM_DTIM_ENABLE_CTS,
5562 	WMI_10_4_VDEV_PARAM_STA_KICKOUT,
5563 	WMI_10_4_VDEV_PARAM_CAPABILITIES,
5564 	WMI_10_4_VDEV_PARAM_TSF_INCREMENT,
5565 	WMI_10_4_VDEV_PARAM_RX_FILTER,
5566 	WMI_10_4_VDEV_PARAM_MGMT_TX_POWER,
5567 	WMI_10_4_VDEV_PARAM_ATF_SSID_SCHED_POLICY,
5568 	WMI_10_4_VDEV_PARAM_DISABLE_DYN_BW_RTS,
5569 	WMI_10_4_VDEV_PARAM_TSF_DECREMENT,
5570 	WMI_10_4_VDEV_PARAM_SELFGEN_FIXED_RATE,
5571 	WMI_10_4_VDEV_PARAM_AMPDU_SUBFRAME_SIZE_PER_AC,
5572 	WMI_10_4_VDEV_PARAM_NSS_VHT160,
5573 	WMI_10_4_VDEV_PARAM_NSS_VHT80_80,
5574 	WMI_10_4_VDEV_PARAM_AMSDU_SUBFRAME_SIZE_PER_AC,
5575 	WMI_10_4_VDEV_PARAM_DISABLE_CABQ,
5576 	WMI_10_4_VDEV_PARAM_SIFS_TRIGGER_RATE,
5577 	WMI_10_4_VDEV_PARAM_TX_POWER,
5578 	WMI_10_4_VDEV_PARAM_ENABLE_DISABLE_RTT_RESPONDER_ROLE,
5579 	WMI_10_4_VDEV_PARAM_DISABLE_4_ADDR_SRC_LRN,
5580 };
5581 
5582 #define WMI_VDEV_DISABLE_4_ADDR_SRC_LRN 1
5583 
5584 #define WMI_VDEV_PARAM_TXBF_SU_TX_BFEE BIT(0)
5585 #define WMI_VDEV_PARAM_TXBF_MU_TX_BFEE BIT(1)
5586 #define WMI_VDEV_PARAM_TXBF_SU_TX_BFER BIT(2)
5587 #define WMI_VDEV_PARAM_TXBF_MU_TX_BFER BIT(3)
5588 
5589 #define WMI_TXBF_STS_CAP_OFFSET_LSB	4
5590 #define WMI_TXBF_STS_CAP_OFFSET_MASK	0x70
5591 #define WMI_TXBF_CONF_IMPLICIT_BF       BIT(7)
5592 #define WMI_BF_SOUND_DIM_OFFSET_LSB	8
5593 #define WMI_BF_SOUND_DIM_OFFSET_MASK	0xf00
5594 
5595 /* slot time long */
5596 #define WMI_VDEV_SLOT_TIME_LONG		0x1
5597 /* slot time short */
5598 #define WMI_VDEV_SLOT_TIME_SHORT	0x2
5599 /* preablbe long */
5600 #define WMI_VDEV_PREAMBLE_LONG		0x1
5601 /* preablbe short */
5602 #define WMI_VDEV_PREAMBLE_SHORT		0x2
5603 
5604 enum wmi_start_event_param {
5605 	WMI_VDEV_RESP_START_EVENT = 0,
5606 	WMI_VDEV_RESP_RESTART_EVENT,
5607 };
5608 
5609 struct wmi_vdev_start_response_event {
5610 	__le32 vdev_id;
5611 	__le32 req_id;
5612 	__le32 resp_type; /* %WMI_VDEV_RESP_ */
5613 	__le32 status;
5614 } __packed;
5615 
5616 struct wmi_vdev_standby_req_event {
5617 	/* unique id identifying the VDEV, generated by the caller */
5618 	__le32 vdev_id;
5619 } __packed;
5620 
5621 struct wmi_vdev_resume_req_event {
5622 	/* unique id identifying the VDEV, generated by the caller */
5623 	__le32 vdev_id;
5624 } __packed;
5625 
5626 struct wmi_vdev_stopped_event {
5627 	/* unique id identifying the VDEV, generated by the caller */
5628 	__le32 vdev_id;
5629 } __packed;
5630 
5631 /*
5632  * common structure used for simple events
5633  * (stopped, resume_req, standby response)
5634  */
5635 struct wmi_vdev_simple_event {
5636 	/* unique id identifying the VDEV, generated by the caller */
5637 	__le32 vdev_id;
5638 } __packed;
5639 
5640 /* VDEV start response status codes */
5641 /* VDEV successfully started */
5642 #define WMI_INIFIED_VDEV_START_RESPONSE_STATUS_SUCCESS	0x0
5643 
5644 /* requested VDEV not found */
5645 #define WMI_INIFIED_VDEV_START_RESPONSE_INVALID_VDEVID	0x1
5646 
5647 /* unsupported VDEV combination */
5648 #define WMI_INIFIED_VDEV_START_RESPONSE_NOT_SUPPORTED	0x2
5649 
5650 /* TODO: please add more comments if you have in-depth information */
5651 struct wmi_vdev_spectral_conf_cmd {
5652 	__le32 vdev_id;
5653 
5654 	/* number of fft samples to send (0 for infinite) */
5655 	__le32 scan_count;
5656 	__le32 scan_period;
5657 	__le32 scan_priority;
5658 
5659 	/* number of bins in the FFT: 2^(fft_size - bin_scale) */
5660 	__le32 scan_fft_size;
5661 	__le32 scan_gc_ena;
5662 	__le32 scan_restart_ena;
5663 	__le32 scan_noise_floor_ref;
5664 	__le32 scan_init_delay;
5665 	__le32 scan_nb_tone_thr;
5666 	__le32 scan_str_bin_thr;
5667 	__le32 scan_wb_rpt_mode;
5668 	__le32 scan_rssi_rpt_mode;
5669 	__le32 scan_rssi_thr;
5670 	__le32 scan_pwr_format;
5671 
5672 	/* rpt_mode: Format of FFT report to software for spectral scan
5673 	 * triggered FFTs:
5674 	 *	0: No FFT report (only spectral scan summary report)
5675 	 *	1: 2-dword summary of metrics for each completed FFT + spectral
5676 	 *	   scan	summary report
5677 	 *	2: 2-dword summary of metrics for each completed FFT +
5678 	 *	   1x- oversampled bins(in-band) per FFT + spectral scan summary
5679 	 *	   report
5680 	 *	3: 2-dword summary of metrics for each completed FFT +
5681 	 *	   2x- oversampled bins	(all) per FFT + spectral scan summary
5682 	 */
5683 	__le32 scan_rpt_mode;
5684 	__le32 scan_bin_scale;
5685 	__le32 scan_dbm_adj;
5686 	__le32 scan_chn_mask;
5687 } __packed;
5688 
5689 struct wmi_vdev_spectral_conf_arg {
5690 	u32 vdev_id;
5691 	u32 scan_count;
5692 	u32 scan_period;
5693 	u32 scan_priority;
5694 	u32 scan_fft_size;
5695 	u32 scan_gc_ena;
5696 	u32 scan_restart_ena;
5697 	u32 scan_noise_floor_ref;
5698 	u32 scan_init_delay;
5699 	u32 scan_nb_tone_thr;
5700 	u32 scan_str_bin_thr;
5701 	u32 scan_wb_rpt_mode;
5702 	u32 scan_rssi_rpt_mode;
5703 	u32 scan_rssi_thr;
5704 	u32 scan_pwr_format;
5705 	u32 scan_rpt_mode;
5706 	u32 scan_bin_scale;
5707 	u32 scan_dbm_adj;
5708 	u32 scan_chn_mask;
5709 };
5710 
5711 #define WMI_SPECTRAL_ENABLE_DEFAULT              0
5712 #define WMI_SPECTRAL_COUNT_DEFAULT               0
5713 #define WMI_SPECTRAL_PERIOD_DEFAULT             35
5714 #define WMI_SPECTRAL_PRIORITY_DEFAULT            1
5715 #define WMI_SPECTRAL_FFT_SIZE_DEFAULT            7
5716 #define WMI_SPECTRAL_GC_ENA_DEFAULT              1
5717 #define WMI_SPECTRAL_RESTART_ENA_DEFAULT         0
5718 #define WMI_SPECTRAL_NOISE_FLOOR_REF_DEFAULT   -96
5719 #define WMI_SPECTRAL_INIT_DELAY_DEFAULT         80
5720 #define WMI_SPECTRAL_NB_TONE_THR_DEFAULT        12
5721 #define WMI_SPECTRAL_STR_BIN_THR_DEFAULT         8
5722 #define WMI_SPECTRAL_WB_RPT_MODE_DEFAULT         0
5723 #define WMI_SPECTRAL_RSSI_RPT_MODE_DEFAULT       0
5724 #define WMI_SPECTRAL_RSSI_THR_DEFAULT         0xf0
5725 #define WMI_SPECTRAL_PWR_FORMAT_DEFAULT          0
5726 #define WMI_SPECTRAL_RPT_MODE_DEFAULT            2
5727 #define WMI_SPECTRAL_BIN_SCALE_DEFAULT           1
5728 #define WMI_SPECTRAL_DBM_ADJ_DEFAULT             1
5729 #define WMI_SPECTRAL_CHN_MASK_DEFAULT            1
5730 
5731 struct wmi_vdev_spectral_enable_cmd {
5732 	__le32 vdev_id;
5733 	__le32 trigger_cmd;
5734 	__le32 enable_cmd;
5735 } __packed;
5736 
5737 #define WMI_SPECTRAL_TRIGGER_CMD_TRIGGER  1
5738 #define WMI_SPECTRAL_TRIGGER_CMD_CLEAR    2
5739 #define WMI_SPECTRAL_ENABLE_CMD_ENABLE    1
5740 #define WMI_SPECTRAL_ENABLE_CMD_DISABLE   2
5741 
5742 /* Beacon processing related command and event structures */
5743 struct wmi_bcn_tx_hdr {
5744 	__le32 vdev_id;
5745 	__le32 tx_rate;
5746 	__le32 tx_power;
5747 	__le32 bcn_len;
5748 } __packed;
5749 
5750 struct wmi_bcn_tx_cmd {
5751 	struct wmi_bcn_tx_hdr hdr;
5752 	u8 *bcn[];
5753 } __packed;
5754 
5755 struct wmi_bcn_tx_arg {
5756 	u32 vdev_id;
5757 	u32 tx_rate;
5758 	u32 tx_power;
5759 	u32 bcn_len;
5760 	const void *bcn;
5761 };
5762 
5763 enum wmi_bcn_tx_ref_flags {
5764 	WMI_BCN_TX_REF_FLAG_DTIM_ZERO = 0x1,
5765 	WMI_BCN_TX_REF_FLAG_DELIVER_CAB = 0x2,
5766 };
5767 
5768 /* TODO: It is unclear why "no antenna" works while any other seemingly valid
5769  * chainmask yields no beacons on the air at all.
5770  */
5771 #define WMI_BCN_TX_REF_DEF_ANTENNA 0
5772 
5773 struct wmi_bcn_tx_ref_cmd {
5774 	__le32 vdev_id;
5775 	__le32 data_len;
5776 	/* physical address of the frame - dma pointer */
5777 	__le32 data_ptr;
5778 	/* id for host to track */
5779 	__le32 msdu_id;
5780 	/* frame ctrl to setup PPDU desc */
5781 	__le32 frame_control;
5782 	/* to control CABQ traffic: WMI_BCN_TX_REF_FLAG_ */
5783 	__le32 flags;
5784 	/* introduced in 10.2 */
5785 	__le32 antenna_mask;
5786 } __packed;
5787 
5788 /* Beacon filter */
5789 #define WMI_BCN_FILTER_ALL   0 /* Filter all beacons */
5790 #define WMI_BCN_FILTER_NONE  1 /* Pass all beacons */
5791 #define WMI_BCN_FILTER_RSSI  2 /* Pass Beacons RSSI >= RSSI threshold */
5792 #define WMI_BCN_FILTER_BSSID 3 /* Pass Beacons with matching BSSID */
5793 #define WMI_BCN_FILTER_SSID  4 /* Pass Beacons with matching SSID */
5794 
5795 struct wmi_bcn_filter_rx_cmd {
5796 	/* Filter ID */
5797 	__le32 bcn_filter_id;
5798 	/* Filter type - wmi_bcn_filter */
5799 	__le32 bcn_filter;
5800 	/* Buffer len */
5801 	__le32 bcn_filter_len;
5802 	/* Filter info (threshold, BSSID, RSSI) */
5803 	u8 *bcn_filter_buf;
5804 } __packed;
5805 
5806 /* Capabilities and IEs to be passed to firmware */
5807 struct wmi_bcn_prb_info {
5808 	/* Capabilities */
5809 	__le32 caps;
5810 	/* ERP info */
5811 	__le32 erp;
5812 	/* Advanced capabilities */
5813 	/* HT capabilities */
5814 	/* HT Info */
5815 	/* ibss_dfs */
5816 	/* wpa Info */
5817 	/* rsn Info */
5818 	/* rrm info */
5819 	/* ath_ext */
5820 	/* app IE */
5821 } __packed;
5822 
5823 enum wmi_sta_ps_mode {
5824 	/* enable power save for the given STA VDEV */
5825 	WMI_STA_PS_MODE_DISABLED = 0,
5826 	/* disable power save  for a given STA VDEV */
5827 	WMI_STA_PS_MODE_ENABLED = 1,
5828 };
5829 
5830 struct wmi_sta_powersave_mode_cmd {
5831 	/* unique id identifying the VDEV, generated by the caller */
5832 	__le32 vdev_id;
5833 
5834 	/*
5835 	 * Power save mode
5836 	 * (see enum wmi_sta_ps_mode)
5837 	 */
5838 	__le32 sta_ps_mode;
5839 } __packed;
5840 
5841 enum wmi_csa_offload_en {
5842 	WMI_CSA_OFFLOAD_DISABLE = 0,
5843 	WMI_CSA_OFFLOAD_ENABLE = 1,
5844 };
5845 
5846 struct wmi_csa_offload_enable_cmd {
5847 	__le32 vdev_id;
5848 	__le32 csa_offload_enable;
5849 } __packed;
5850 
5851 struct wmi_csa_offload_chanswitch_cmd {
5852 	__le32 vdev_id;
5853 	struct wmi_channel chan;
5854 } __packed;
5855 
5856 /*
5857  * This parameter controls the policy for retrieving frames from AP while the
5858  * STA is in sleep state.
5859  *
5860  * Only takes affect if the sta_ps_mode is enabled
5861  */
5862 enum wmi_sta_ps_param_rx_wake_policy {
5863 	/*
5864 	 * Wake up when ever there is an  RX activity on the VDEV. In this mode
5865 	 * the Power save SM(state machine) will come out of sleep by either
5866 	 * sending null frame (or) a data frame (with PS==0) in response to TIM
5867 	 * bit set in the received beacon frame from AP.
5868 	 */
5869 	WMI_STA_PS_RX_WAKE_POLICY_WAKE = 0,
5870 
5871 	/*
5872 	 * Here the power save state machine will not wakeup in response to TIM
5873 	 * bit, instead it will send a PSPOLL (or) UASPD trigger based on UAPSD
5874 	 * configuration setup by WMISET_PS_SET_UAPSD  WMI command.  When all
5875 	 * access categories are delivery-enabled, the station will send a
5876 	 * UAPSD trigger frame, otherwise it will send a PS-Poll.
5877 	 */
5878 	WMI_STA_PS_RX_WAKE_POLICY_POLL_UAPSD = 1,
5879 };
5880 
5881 /*
5882  * Number of tx frames/beacon  that cause the power save SM to wake up.
5883  *
5884  * Value 1 causes the SM to wake up for every TX. Value 0 has a special
5885  * meaning, It will cause the SM to never wake up. This is useful if you want
5886  * to keep the system to sleep all the time for some kind of test mode . host
5887  * can change this parameter any time.  It will affect at the next tx frame.
5888  */
5889 enum wmi_sta_ps_param_tx_wake_threshold {
5890 	WMI_STA_PS_TX_WAKE_THRESHOLD_NEVER = 0,
5891 	WMI_STA_PS_TX_WAKE_THRESHOLD_ALWAYS = 1,
5892 
5893 	/*
5894 	 * Values greater than one indicate that many TX attempts per beacon
5895 	 * interval before the STA will wake up
5896 	 */
5897 };
5898 
5899 /*
5900  * The maximum number of PS-Poll frames the FW will send in response to
5901  * traffic advertised in TIM before waking up (by sending a null frame with PS
5902  * = 0). Value 0 has a special meaning: there is no maximum count and the FW
5903  * will send as many PS-Poll as are necessary to retrieve buffered BU. This
5904  * parameter is used when the RX wake policy is
5905  * WMI_STA_PS_RX_WAKE_POLICY_POLL_UAPSD and ignored when the RX wake
5906  * policy is WMI_STA_PS_RX_WAKE_POLICY_WAKE.
5907  */
5908 enum wmi_sta_ps_param_pspoll_count {
5909 	WMI_STA_PS_PSPOLL_COUNT_NO_MAX = 0,
5910 	/*
5911 	 * Values greater than 0 indicate the maximum number of PS-Poll frames
5912 	 * FW will send before waking up.
5913 	 */
5914 
5915 	/* When u-APSD is enabled the firmware will be very reluctant to exit
5916 	 * STA PS. This could result in very poor Rx performance with STA doing
5917 	 * PS-Poll for each and every buffered frame. This value is a bit
5918 	 * arbitrary.
5919 	 */
5920 	WMI_STA_PS_PSPOLL_COUNT_UAPSD = 3,
5921 };
5922 
5923 /*
5924  * This will include the delivery and trigger enabled state for every AC.
5925  * This is the negotiated state with AP. The host MLME needs to set this based
5926  * on AP capability and the state Set in the association request by the
5927  * station MLME.Lower 8 bits of the value specify the UAPSD configuration.
5928  */
5929 #define WMI_UAPSD_AC_TYPE_DELI 0
5930 #define WMI_UAPSD_AC_TYPE_TRIG 1
5931 
5932 #define WMI_UAPSD_AC_BIT_MASK(ac, type) \
5933 	(type == WMI_UAPSD_AC_TYPE_DELI ? 1 << (ac << 1) : 1 << ((ac << 1) + 1))
5934 
5935 enum wmi_sta_ps_param_uapsd {
5936 	WMI_STA_PS_UAPSD_AC0_DELIVERY_EN = (1 << 0),
5937 	WMI_STA_PS_UAPSD_AC0_TRIGGER_EN  = (1 << 1),
5938 	WMI_STA_PS_UAPSD_AC1_DELIVERY_EN = (1 << 2),
5939 	WMI_STA_PS_UAPSD_AC1_TRIGGER_EN  = (1 << 3),
5940 	WMI_STA_PS_UAPSD_AC2_DELIVERY_EN = (1 << 4),
5941 	WMI_STA_PS_UAPSD_AC2_TRIGGER_EN  = (1 << 5),
5942 	WMI_STA_PS_UAPSD_AC3_DELIVERY_EN = (1 << 6),
5943 	WMI_STA_PS_UAPSD_AC3_TRIGGER_EN  = (1 << 7),
5944 };
5945 
5946 #define WMI_STA_UAPSD_MAX_INTERVAL_MSEC UINT_MAX
5947 
5948 struct wmi_sta_uapsd_auto_trig_param {
5949 	__le32 wmm_ac;
5950 	__le32 user_priority;
5951 	__le32 service_interval;
5952 	__le32 suspend_interval;
5953 	__le32 delay_interval;
5954 };
5955 
5956 struct wmi_sta_uapsd_auto_trig_cmd_fixed_param {
5957 	__le32 vdev_id;
5958 	struct wmi_mac_addr peer_macaddr;
5959 	__le32 num_ac;
5960 };
5961 
5962 struct wmi_sta_uapsd_auto_trig_arg {
5963 	u32 wmm_ac;
5964 	u32 user_priority;
5965 	u32 service_interval;
5966 	u32 suspend_interval;
5967 	u32 delay_interval;
5968 };
5969 
5970 enum wmi_sta_powersave_param {
5971 	/*
5972 	 * Controls how frames are retrievd from AP while STA is sleeping
5973 	 *
5974 	 * (see enum wmi_sta_ps_param_rx_wake_policy)
5975 	 */
5976 	WMI_STA_PS_PARAM_RX_WAKE_POLICY = 0,
5977 
5978 	/*
5979 	 * The STA will go active after this many TX
5980 	 *
5981 	 * (see enum wmi_sta_ps_param_tx_wake_threshold)
5982 	 */
5983 	WMI_STA_PS_PARAM_TX_WAKE_THRESHOLD = 1,
5984 
5985 	/*
5986 	 * Number of PS-Poll to send before STA wakes up
5987 	 *
5988 	 * (see enum wmi_sta_ps_param_pspoll_count)
5989 	 *
5990 	 */
5991 	WMI_STA_PS_PARAM_PSPOLL_COUNT = 2,
5992 
5993 	/*
5994 	 * TX/RX inactivity time in msec before going to sleep.
5995 	 *
5996 	 * The power save SM will monitor tx/rx activity on the VDEV, if no
5997 	 * activity for the specified msec of the parameter the Power save
5998 	 * SM will go to sleep.
5999 	 */
6000 	WMI_STA_PS_PARAM_INACTIVITY_TIME = 3,
6001 
6002 	/*
6003 	 * Set uapsd configuration.
6004 	 *
6005 	 * (see enum wmi_sta_ps_param_uapsd)
6006 	 */
6007 	WMI_STA_PS_PARAM_UAPSD = 4,
6008 };
6009 
6010 struct wmi_sta_powersave_param_cmd {
6011 	__le32 vdev_id;
6012 	__le32 param_id; /* %WMI_STA_PS_PARAM_ */
6013 	__le32 param_value;
6014 } __packed;
6015 
6016 /* No MIMO power save */
6017 #define WMI_STA_MIMO_PS_MODE_DISABLE
6018 /* mimo powersave mode static*/
6019 #define WMI_STA_MIMO_PS_MODE_STATIC
6020 /* mimo powersave mode dynamic */
6021 #define WMI_STA_MIMO_PS_MODE_DYNAMIC
6022 
6023 struct wmi_sta_mimo_ps_mode_cmd {
6024 	/* unique id identifying the VDEV, generated by the caller */
6025 	__le32 vdev_id;
6026 	/* mimo powersave mode as defined above */
6027 	__le32 mimo_pwrsave_mode;
6028 } __packed;
6029 
6030 /* U-APSD configuration of peer station from (re)assoc request and TSPECs */
6031 enum wmi_ap_ps_param_uapsd {
6032 	WMI_AP_PS_UAPSD_AC0_DELIVERY_EN = (1 << 0),
6033 	WMI_AP_PS_UAPSD_AC0_TRIGGER_EN  = (1 << 1),
6034 	WMI_AP_PS_UAPSD_AC1_DELIVERY_EN = (1 << 2),
6035 	WMI_AP_PS_UAPSD_AC1_TRIGGER_EN  = (1 << 3),
6036 	WMI_AP_PS_UAPSD_AC2_DELIVERY_EN = (1 << 4),
6037 	WMI_AP_PS_UAPSD_AC2_TRIGGER_EN  = (1 << 5),
6038 	WMI_AP_PS_UAPSD_AC3_DELIVERY_EN = (1 << 6),
6039 	WMI_AP_PS_UAPSD_AC3_TRIGGER_EN  = (1 << 7),
6040 };
6041 
6042 /* U-APSD maximum service period of peer station */
6043 enum wmi_ap_ps_peer_param_max_sp {
6044 	WMI_AP_PS_PEER_PARAM_MAX_SP_UNLIMITED = 0,
6045 	WMI_AP_PS_PEER_PARAM_MAX_SP_2 = 1,
6046 	WMI_AP_PS_PEER_PARAM_MAX_SP_4 = 2,
6047 	WMI_AP_PS_PEER_PARAM_MAX_SP_6 = 3,
6048 	MAX_WMI_AP_PS_PEER_PARAM_MAX_SP,
6049 };
6050 
6051 /*
6052  * AP power save parameter
6053  * Set a power save specific parameter for a peer station
6054  */
6055 enum wmi_ap_ps_peer_param {
6056 	/* Set uapsd configuration for a given peer.
6057 	 *
6058 	 * Include the delivery and trigger enabled state for every AC.
6059 	 * The host  MLME needs to set this based on AP capability and stations
6060 	 * request Set in the association request  received from the station.
6061 	 *
6062 	 * Lower 8 bits of the value specify the UAPSD configuration.
6063 	 *
6064 	 * (see enum wmi_ap_ps_param_uapsd)
6065 	 * The default value is 0.
6066 	 */
6067 	WMI_AP_PS_PEER_PARAM_UAPSD = 0,
6068 
6069 	/*
6070 	 * Set the service period for a UAPSD capable station
6071 	 *
6072 	 * The service period from wme ie in the (re)assoc request frame.
6073 	 *
6074 	 * (see enum wmi_ap_ps_peer_param_max_sp)
6075 	 */
6076 	WMI_AP_PS_PEER_PARAM_MAX_SP = 1,
6077 
6078 	/* Time in seconds for aging out buffered frames for STA in PS */
6079 	WMI_AP_PS_PEER_PARAM_AGEOUT_TIME = 2,
6080 };
6081 
6082 struct wmi_ap_ps_peer_cmd {
6083 	/* unique id identifying the VDEV, generated by the caller */
6084 	__le32 vdev_id;
6085 
6086 	/* peer MAC address */
6087 	struct wmi_mac_addr peer_macaddr;
6088 
6089 	/* AP powersave param (see enum wmi_ap_ps_peer_param) */
6090 	__le32 param_id;
6091 
6092 	/* AP powersave param value */
6093 	__le32 param_value;
6094 } __packed;
6095 
6096 /* 128 clients = 4 words */
6097 #define WMI_TIM_BITMAP_ARRAY_SIZE 4
6098 
6099 struct wmi_tim_info {
6100 	__le32 tim_len;
6101 	__le32 tim_mcast;
6102 	__le32 tim_bitmap[WMI_TIM_BITMAP_ARRAY_SIZE];
6103 	__le32 tim_changed;
6104 	__le32 tim_num_ps_pending;
6105 } __packed;
6106 
6107 struct wmi_tim_info_arg {
6108 	__le32 tim_len;
6109 	__le32 tim_mcast;
6110 	const __le32 *tim_bitmap;
6111 	__le32 tim_changed;
6112 	__le32 tim_num_ps_pending;
6113 } __packed;
6114 
6115 /* Maximum number of NOA Descriptors supported */
6116 #define WMI_P2P_MAX_NOA_DESCRIPTORS 4
6117 #define WMI_P2P_OPPPS_ENABLE_BIT	BIT(0)
6118 #define WMI_P2P_OPPPS_CTWINDOW_OFFSET	1
6119 #define WMI_P2P_NOA_CHANGED_BIT	BIT(0)
6120 
6121 struct wmi_p2p_noa_info {
6122 	/* Bit 0 - Flag to indicate an update in NOA schedule
6123 	 * Bits 7-1 - Reserved
6124 	 */
6125 	u8 changed;
6126 	/* NOA index */
6127 	u8 index;
6128 	/* Bit 0 - Opp PS state of the AP
6129 	 * Bits 1-7 - Ctwindow in TUs
6130 	 */
6131 	u8 ctwindow_oppps;
6132 	/* Number of NOA descriptors */
6133 	u8 num_descriptors;
6134 
6135 	struct wmi_p2p_noa_descriptor descriptors[WMI_P2P_MAX_NOA_DESCRIPTORS];
6136 } __packed;
6137 
6138 struct wmi_bcn_info {
6139 	struct wmi_tim_info tim_info;
6140 	struct wmi_p2p_noa_info p2p_noa_info;
6141 } __packed;
6142 
6143 struct wmi_host_swba_event {
6144 	__le32 vdev_map;
6145 	struct wmi_bcn_info bcn_info[];
6146 } __packed;
6147 
6148 struct wmi_10_2_4_bcn_info {
6149 	struct wmi_tim_info tim_info;
6150 	/* The 10.2.4 FW doesn't have p2p NOA info */
6151 } __packed;
6152 
6153 struct wmi_10_2_4_host_swba_event {
6154 	__le32 vdev_map;
6155 	struct wmi_10_2_4_bcn_info bcn_info[];
6156 } __packed;
6157 
6158 /* 16 words = 512 client + 1 word = for guard */
6159 #define WMI_10_4_TIM_BITMAP_ARRAY_SIZE 17
6160 
6161 struct wmi_10_4_tim_info {
6162 	__le32 tim_len;
6163 	__le32 tim_mcast;
6164 	__le32 tim_bitmap[WMI_10_4_TIM_BITMAP_ARRAY_SIZE];
6165 	__le32 tim_changed;
6166 	__le32 tim_num_ps_pending;
6167 } __packed;
6168 
6169 #define WMI_10_4_P2P_MAX_NOA_DESCRIPTORS 1
6170 
6171 struct wmi_10_4_p2p_noa_info {
6172 	/* Bit 0 - Flag to indicate an update in NOA schedule
6173 	 * Bits 7-1 - Reserved
6174 	 */
6175 	u8 changed;
6176 	/* NOA index */
6177 	u8 index;
6178 	/* Bit 0 - Opp PS state of the AP
6179 	 * Bits 1-7 - Ctwindow in TUs
6180 	 */
6181 	u8 ctwindow_oppps;
6182 	/* Number of NOA descriptors */
6183 	u8 num_descriptors;
6184 
6185 	struct wmi_p2p_noa_descriptor
6186 		noa_descriptors[WMI_10_4_P2P_MAX_NOA_DESCRIPTORS];
6187 } __packed;
6188 
6189 struct wmi_10_4_bcn_info {
6190 	struct wmi_10_4_tim_info tim_info;
6191 	struct wmi_10_4_p2p_noa_info p2p_noa_info;
6192 } __packed;
6193 
6194 struct wmi_10_4_host_swba_event {
6195 	__le32 vdev_map;
6196 	struct wmi_10_4_bcn_info bcn_info[];
6197 } __packed;
6198 
6199 #define WMI_MAX_AP_VDEV 16
6200 
6201 struct wmi_tbtt_offset_event {
6202 	__le32 vdev_map;
6203 	__le32 tbttoffset_list[WMI_MAX_AP_VDEV];
6204 } __packed;
6205 
6206 struct wmi_peer_create_cmd {
6207 	__le32 vdev_id;
6208 	struct wmi_mac_addr peer_macaddr;
6209 	__le32 peer_type;
6210 } __packed;
6211 
6212 enum wmi_peer_type {
6213 	WMI_PEER_TYPE_DEFAULT = 0,
6214 	WMI_PEER_TYPE_BSS = 1,
6215 	WMI_PEER_TYPE_TDLS = 2,
6216 };
6217 
6218 struct wmi_peer_delete_cmd {
6219 	__le32 vdev_id;
6220 	struct wmi_mac_addr peer_macaddr;
6221 } __packed;
6222 
6223 struct wmi_peer_flush_tids_cmd {
6224 	__le32 vdev_id;
6225 	struct wmi_mac_addr peer_macaddr;
6226 	__le32 peer_tid_bitmap;
6227 } __packed;
6228 
6229 struct wmi_fixed_rate {
6230 	/*
6231 	 * rate mode . 0: disable fixed rate (auto rate)
6232 	 *   1: legacy (non 11n) rate  specified as ieee rate 2*Mbps
6233 	 *   2: ht20 11n rate  specified as mcs index
6234 	 *   3: ht40 11n rate  specified as mcs index
6235 	 */
6236 	__le32  rate_mode;
6237 	/*
6238 	 * 4 rate values for 4 rate series. series 0 is stored in byte 0 (LSB)
6239 	 * and series 3 is stored at byte 3 (MSB)
6240 	 */
6241 	__le32  rate_series;
6242 	/*
6243 	 * 4 retry counts for 4 rate series. retry count for rate 0 is stored
6244 	 * in byte 0 (LSB) and retry count for rate 3 is stored at byte 3
6245 	 * (MSB)
6246 	 */
6247 	__le32  rate_retries;
6248 } __packed;
6249 
6250 struct wmi_peer_fixed_rate_cmd {
6251 	/* unique id identifying the VDEV, generated by the caller */
6252 	__le32 vdev_id;
6253 	/* peer MAC address */
6254 	struct wmi_mac_addr peer_macaddr;
6255 	/* fixed rate */
6256 	struct wmi_fixed_rate peer_fixed_rate;
6257 } __packed;
6258 
6259 #define WMI_MGMT_TID    17
6260 
6261 struct wmi_addba_clear_resp_cmd {
6262 	/* unique id identifying the VDEV, generated by the caller */
6263 	__le32 vdev_id;
6264 	/* peer MAC address */
6265 	struct wmi_mac_addr peer_macaddr;
6266 } __packed;
6267 
6268 struct wmi_addba_send_cmd {
6269 	/* unique id identifying the VDEV, generated by the caller */
6270 	__le32 vdev_id;
6271 	/* peer MAC address */
6272 	struct wmi_mac_addr peer_macaddr;
6273 	/* Tid number */
6274 	__le32 tid;
6275 	/* Buffer/Window size*/
6276 	__le32 buffersize;
6277 } __packed;
6278 
6279 struct wmi_delba_send_cmd {
6280 	/* unique id identifying the VDEV, generated by the caller */
6281 	__le32 vdev_id;
6282 	/* peer MAC address */
6283 	struct wmi_mac_addr peer_macaddr;
6284 	/* Tid number */
6285 	__le32 tid;
6286 	/* Is Initiator */
6287 	__le32 initiator;
6288 	/* Reason code */
6289 	__le32 reasoncode;
6290 } __packed;
6291 
6292 struct wmi_addba_setresponse_cmd {
6293 	/* unique id identifying the vdev, generated by the caller */
6294 	__le32 vdev_id;
6295 	/* peer mac address */
6296 	struct wmi_mac_addr peer_macaddr;
6297 	/* Tid number */
6298 	__le32 tid;
6299 	/* status code */
6300 	__le32 statuscode;
6301 } __packed;
6302 
6303 struct wmi_send_singleamsdu_cmd {
6304 	/* unique id identifying the vdev, generated by the caller */
6305 	__le32 vdev_id;
6306 	/* peer mac address */
6307 	struct wmi_mac_addr peer_macaddr;
6308 	/* Tid number */
6309 	__le32 tid;
6310 } __packed;
6311 
6312 enum wmi_peer_smps_state {
6313 	WMI_PEER_SMPS_PS_NONE = 0x0,
6314 	WMI_PEER_SMPS_STATIC  = 0x1,
6315 	WMI_PEER_SMPS_DYNAMIC = 0x2
6316 };
6317 
6318 enum wmi_peer_chwidth {
6319 	WMI_PEER_CHWIDTH_20MHZ = 0,
6320 	WMI_PEER_CHWIDTH_40MHZ = 1,
6321 	WMI_PEER_CHWIDTH_80MHZ = 2,
6322 	WMI_PEER_CHWIDTH_160MHZ = 3,
6323 };
6324 
6325 enum wmi_peer_param {
6326 	WMI_PEER_SMPS_STATE = 0x1, /* see %wmi_peer_smps_state */
6327 	WMI_PEER_AMPDU      = 0x2,
6328 	WMI_PEER_AUTHORIZE  = 0x3,
6329 	WMI_PEER_CHAN_WIDTH = 0x4,
6330 	WMI_PEER_NSS        = 0x5,
6331 	WMI_PEER_USE_4ADDR  = 0x6,
6332 	WMI_PEER_USE_FIXED_PWR = 0x8,
6333 	WMI_PEER_PARAM_FIXED_RATE = 0x9,
6334 	WMI_PEER_DEBUG      = 0xa,
6335 	WMI_PEER_PHYMODE    = 0xd,
6336 	WMI_PEER_DUMMY_VAR  = 0xff, /* dummy parameter for STA PS workaround */
6337 };
6338 
6339 struct wmi_peer_set_param_cmd {
6340 	__le32 vdev_id;
6341 	struct wmi_mac_addr peer_macaddr;
6342 	__le32 param_id;
6343 	__le32 param_value;
6344 } __packed;
6345 
6346 #define MAX_SUPPORTED_RATES 128
6347 
6348 struct wmi_rate_set {
6349 	/* total number of rates */
6350 	__le32 num_rates;
6351 	/*
6352 	 * rates (each 8bit value) packed into a 32 bit word.
6353 	 * the rates are filled from least significant byte to most
6354 	 * significant byte.
6355 	 */
6356 	__le32 rates[(MAX_SUPPORTED_RATES / 4) + 1];
6357 } __packed;
6358 
6359 struct wmi_rate_set_arg {
6360 	unsigned int num_rates;
6361 	u8 rates[MAX_SUPPORTED_RATES];
6362 };
6363 
6364 /*
6365  * NOTE: It would bea good idea to represent the Tx MCS
6366  * info in one word and Rx in another word. This is split
6367  * into multiple words for convenience
6368  */
6369 struct wmi_vht_rate_set {
6370 	__le32 rx_max_rate; /* Max Rx data rate */
6371 	__le32 rx_mcs_set;  /* Negotiated RX VHT rates */
6372 	__le32 tx_max_rate; /* Max Tx data rate */
6373 	__le32 tx_mcs_set;  /* Negotiated TX VHT rates */
6374 } __packed;
6375 
6376 struct wmi_vht_rate_set_arg {
6377 	u32 rx_max_rate;
6378 	u32 rx_mcs_set;
6379 	u32 tx_max_rate;
6380 	u32 tx_mcs_set;
6381 };
6382 
6383 struct wmi_peer_set_rates_cmd {
6384 	/* peer MAC address */
6385 	struct wmi_mac_addr peer_macaddr;
6386 	/* legacy rate set */
6387 	struct wmi_rate_set peer_legacy_rates;
6388 	/* ht rate set */
6389 	struct wmi_rate_set peer_ht_rates;
6390 } __packed;
6391 
6392 struct wmi_peer_set_q_empty_callback_cmd {
6393 	/* unique id identifying the VDEV, generated by the caller */
6394 	__le32 vdev_id;
6395 	/* peer MAC address */
6396 	struct wmi_mac_addr peer_macaddr;
6397 	__le32 callback_enable;
6398 } __packed;
6399 
6400 struct wmi_peer_flags_map {
6401 	u32 auth;
6402 	u32 qos;
6403 	u32 need_ptk_4_way;
6404 	u32 need_gtk_2_way;
6405 	u32 apsd;
6406 	u32 ht;
6407 	u32 bw40;
6408 	u32 stbc;
6409 	u32 ldbc;
6410 	u32 dyn_mimops;
6411 	u32 static_mimops;
6412 	u32 spatial_mux;
6413 	u32 vht;
6414 	u32 bw80;
6415 	u32 vht_2g;
6416 	u32 pmf;
6417 	u32 bw160;
6418 };
6419 
6420 enum wmi_peer_flags {
6421 	WMI_PEER_AUTH = 0x00000001,
6422 	WMI_PEER_QOS = 0x00000002,
6423 	WMI_PEER_NEED_PTK_4_WAY = 0x00000004,
6424 	WMI_PEER_NEED_GTK_2_WAY = 0x00000010,
6425 	WMI_PEER_APSD = 0x00000800,
6426 	WMI_PEER_HT = 0x00001000,
6427 	WMI_PEER_40MHZ = 0x00002000,
6428 	WMI_PEER_STBC = 0x00008000,
6429 	WMI_PEER_LDPC = 0x00010000,
6430 	WMI_PEER_DYN_MIMOPS = 0x00020000,
6431 	WMI_PEER_STATIC_MIMOPS = 0x00040000,
6432 	WMI_PEER_SPATIAL_MUX = 0x00200000,
6433 	WMI_PEER_VHT = 0x02000000,
6434 	WMI_PEER_80MHZ = 0x04000000,
6435 	WMI_PEER_VHT_2G = 0x08000000,
6436 	WMI_PEER_PMF = 0x10000000,
6437 	WMI_PEER_160MHZ = 0x20000000
6438 };
6439 
6440 enum wmi_10x_peer_flags {
6441 	WMI_10X_PEER_AUTH = 0x00000001,
6442 	WMI_10X_PEER_QOS = 0x00000002,
6443 	WMI_10X_PEER_NEED_PTK_4_WAY = 0x00000004,
6444 	WMI_10X_PEER_NEED_GTK_2_WAY = 0x00000010,
6445 	WMI_10X_PEER_APSD = 0x00000800,
6446 	WMI_10X_PEER_HT = 0x00001000,
6447 	WMI_10X_PEER_40MHZ = 0x00002000,
6448 	WMI_10X_PEER_STBC = 0x00008000,
6449 	WMI_10X_PEER_LDPC = 0x00010000,
6450 	WMI_10X_PEER_DYN_MIMOPS = 0x00020000,
6451 	WMI_10X_PEER_STATIC_MIMOPS = 0x00040000,
6452 	WMI_10X_PEER_SPATIAL_MUX = 0x00200000,
6453 	WMI_10X_PEER_VHT = 0x02000000,
6454 	WMI_10X_PEER_80MHZ = 0x04000000,
6455 	WMI_10X_PEER_160MHZ = 0x20000000
6456 };
6457 
6458 enum wmi_10_2_peer_flags {
6459 	WMI_10_2_PEER_AUTH = 0x00000001,
6460 	WMI_10_2_PEER_QOS = 0x00000002,
6461 	WMI_10_2_PEER_NEED_PTK_4_WAY = 0x00000004,
6462 	WMI_10_2_PEER_NEED_GTK_2_WAY = 0x00000010,
6463 	WMI_10_2_PEER_APSD = 0x00000800,
6464 	WMI_10_2_PEER_HT = 0x00001000,
6465 	WMI_10_2_PEER_40MHZ = 0x00002000,
6466 	WMI_10_2_PEER_STBC = 0x00008000,
6467 	WMI_10_2_PEER_LDPC = 0x00010000,
6468 	WMI_10_2_PEER_DYN_MIMOPS = 0x00020000,
6469 	WMI_10_2_PEER_STATIC_MIMOPS = 0x00040000,
6470 	WMI_10_2_PEER_SPATIAL_MUX = 0x00200000,
6471 	WMI_10_2_PEER_VHT = 0x02000000,
6472 	WMI_10_2_PEER_80MHZ = 0x04000000,
6473 	WMI_10_2_PEER_VHT_2G = 0x08000000,
6474 	WMI_10_2_PEER_PMF = 0x10000000,
6475 	WMI_10_2_PEER_160MHZ = 0x20000000
6476 };
6477 
6478 /*
6479  * Peer rate capabilities.
6480  *
6481  * This is of interest to the ratecontrol
6482  * module which resides in the firmware. The bit definitions are
6483  * consistent with that defined in if_athrate.c.
6484  */
6485 #define WMI_RC_DS_FLAG          0x01
6486 #define WMI_RC_CW40_FLAG        0x02
6487 #define WMI_RC_SGI_FLAG         0x04
6488 #define WMI_RC_HT_FLAG          0x08
6489 #define WMI_RC_RTSCTS_FLAG      0x10
6490 #define WMI_RC_TX_STBC_FLAG     0x20
6491 #define WMI_RC_RX_STBC_FLAG     0xC0
6492 #define WMI_RC_RX_STBC_FLAG_S   6
6493 #define WMI_RC_WEP_TKIP_FLAG    0x100
6494 #define WMI_RC_TS_FLAG          0x200
6495 #define WMI_RC_UAPSD_FLAG       0x400
6496 
6497 /* Maximum listen interval supported by hw in units of beacon interval */
6498 #define ATH10K_MAX_HW_LISTEN_INTERVAL 5
6499 
6500 struct wmi_common_peer_assoc_complete_cmd {
6501 	struct wmi_mac_addr peer_macaddr;
6502 	__le32 vdev_id;
6503 	__le32 peer_new_assoc; /* 1=assoc, 0=reassoc */
6504 	__le32 peer_associd; /* 16 LSBs */
6505 	__le32 peer_flags;
6506 	__le32 peer_caps; /* 16 LSBs */
6507 	__le32 peer_listen_intval;
6508 	__le32 peer_ht_caps;
6509 	__le32 peer_max_mpdu;
6510 	__le32 peer_mpdu_density; /* 0..16 */
6511 	__le32 peer_rate_caps;
6512 	struct wmi_rate_set peer_legacy_rates;
6513 	struct wmi_rate_set peer_ht_rates;
6514 	__le32 peer_nss; /* num of spatial streams */
6515 	__le32 peer_vht_caps;
6516 	__le32 peer_phymode;
6517 	struct wmi_vht_rate_set peer_vht_rates;
6518 };
6519 
6520 struct wmi_main_peer_assoc_complete_cmd {
6521 	struct wmi_common_peer_assoc_complete_cmd cmd;
6522 
6523 	/* HT Operation Element of the peer. Five bytes packed in 2
6524 	 *  INT32 array and filled from lsb to msb.
6525 	 */
6526 	__le32 peer_ht_info[2];
6527 } __packed;
6528 
6529 struct wmi_10_1_peer_assoc_complete_cmd {
6530 	struct wmi_common_peer_assoc_complete_cmd cmd;
6531 } __packed;
6532 
6533 #define WMI_PEER_ASSOC_INFO0_MAX_MCS_IDX_LSB 0
6534 #define WMI_PEER_ASSOC_INFO0_MAX_MCS_IDX_MASK 0x0f
6535 #define WMI_PEER_ASSOC_INFO0_MAX_NSS_LSB 4
6536 #define WMI_PEER_ASSOC_INFO0_MAX_NSS_MASK 0xf0
6537 
6538 struct wmi_10_2_peer_assoc_complete_cmd {
6539 	struct wmi_common_peer_assoc_complete_cmd cmd;
6540 	__le32 info0; /* WMI_PEER_ASSOC_INFO0_ */
6541 } __packed;
6542 
6543 /* NSS Mapping to FW */
6544 #define WMI_PEER_NSS_MAP_ENABLE	BIT(31)
6545 #define WMI_PEER_NSS_160MHZ_MASK	GENMASK(2, 0)
6546 #define WMI_PEER_NSS_80_80MHZ_MASK	GENMASK(5, 3)
6547 
6548 struct wmi_10_4_peer_assoc_complete_cmd {
6549 	struct wmi_10_2_peer_assoc_complete_cmd cmd;
6550 	__le32 peer_bw_rxnss_override;
6551 } __packed;
6552 
6553 struct wmi_peer_assoc_complete_arg {
6554 	u8 addr[ETH_ALEN];
6555 	u32 vdev_id;
6556 	bool peer_reassoc;
6557 	u16 peer_aid;
6558 	u32 peer_flags; /* see %WMI_PEER_ */
6559 	u16 peer_caps;
6560 	u32 peer_listen_intval;
6561 	u32 peer_ht_caps;
6562 	u32 peer_max_mpdu;
6563 	u32 peer_mpdu_density; /* 0..16 */
6564 	u32 peer_rate_caps; /* see %WMI_RC_ */
6565 	struct wmi_rate_set_arg peer_legacy_rates;
6566 	struct wmi_rate_set_arg peer_ht_rates;
6567 	u32 peer_num_spatial_streams;
6568 	u32 peer_vht_caps;
6569 	enum wmi_phy_mode peer_phymode;
6570 	struct wmi_vht_rate_set_arg peer_vht_rates;
6571 	u32 peer_bw_rxnss_override;
6572 };
6573 
6574 struct wmi_peer_add_wds_entry_cmd {
6575 	/* peer MAC address */
6576 	struct wmi_mac_addr peer_macaddr;
6577 	/* wds MAC addr */
6578 	struct wmi_mac_addr wds_macaddr;
6579 } __packed;
6580 
6581 struct wmi_peer_remove_wds_entry_cmd {
6582 	/* wds MAC addr */
6583 	struct wmi_mac_addr wds_macaddr;
6584 } __packed;
6585 
6586 struct wmi_peer_q_empty_callback_event {
6587 	/* peer MAC address */
6588 	struct wmi_mac_addr peer_macaddr;
6589 } __packed;
6590 
6591 /*
6592  * Channel info WMI event
6593  */
6594 struct wmi_chan_info_event {
6595 	__le32 err_code;
6596 	__le32 freq;
6597 	__le32 cmd_flags;
6598 	__le32 noise_floor;
6599 	__le32 rx_clear_count;
6600 	__le32 cycle_count;
6601 } __packed;
6602 
6603 struct wmi_10_4_chan_info_event {
6604 	__le32 err_code;
6605 	__le32 freq;
6606 	__le32 cmd_flags;
6607 	__le32 noise_floor;
6608 	__le32 rx_clear_count;
6609 	__le32 cycle_count;
6610 	__le32 chan_tx_pwr_range;
6611 	__le32 chan_tx_pwr_tp;
6612 	__le32 rx_frame_count;
6613 } __packed;
6614 
6615 struct wmi_peer_sta_kickout_event {
6616 	struct wmi_mac_addr peer_macaddr;
6617 } __packed;
6618 
6619 #define WMI_CHAN_INFO_FLAG_COMPLETE BIT(0)
6620 #define WMI_CHAN_INFO_FLAG_PRE_COMPLETE BIT(1)
6621 
6622 /* Beacon filter wmi command info */
6623 #define BCN_FLT_MAX_SUPPORTED_IES	256
6624 #define BCN_FLT_MAX_ELEMS_IE_LIST	(BCN_FLT_MAX_SUPPORTED_IES / 32)
6625 
6626 struct bss_bcn_stats {
6627 	__le32 vdev_id;
6628 	__le32 bss_bcnsdropped;
6629 	__le32 bss_bcnsdelivered;
6630 } __packed;
6631 
6632 struct bcn_filter_stats {
6633 	__le32 bcns_dropped;
6634 	__le32 bcns_delivered;
6635 	__le32 activefilters;
6636 	struct bss_bcn_stats bss_stats;
6637 } __packed;
6638 
6639 struct wmi_add_bcn_filter_cmd {
6640 	u32 vdev_id;
6641 	u32 ie_map[BCN_FLT_MAX_ELEMS_IE_LIST];
6642 } __packed;
6643 
6644 enum wmi_sta_keepalive_method {
6645 	WMI_STA_KEEPALIVE_METHOD_NULL_FRAME = 1,
6646 	WMI_STA_KEEPALIVE_METHOD_UNSOLICITATED_ARP_RESPONSE = 2,
6647 };
6648 
6649 #define WMI_STA_KEEPALIVE_INTERVAL_DISABLE 0
6650 
6651 /* Firmware crashes if keepalive interval exceeds this limit */
6652 #define WMI_STA_KEEPALIVE_INTERVAL_MAX_SECONDS 0xffff
6653 
6654 /* note: ip4 addresses are in network byte order, i.e. big endian */
6655 struct wmi_sta_keepalive_arp_resp {
6656 	__be32 src_ip4_addr;
6657 	__be32 dest_ip4_addr;
6658 	struct wmi_mac_addr dest_mac_addr;
6659 } __packed;
6660 
6661 struct wmi_sta_keepalive_cmd {
6662 	__le32 vdev_id;
6663 	__le32 enabled;
6664 	__le32 method; /* WMI_STA_KEEPALIVE_METHOD_ */
6665 	__le32 interval; /* in seconds */
6666 	struct wmi_sta_keepalive_arp_resp arp_resp;
6667 } __packed;
6668 
6669 struct wmi_sta_keepalive_arg {
6670 	u32 vdev_id;
6671 	u32 enabled;
6672 	u32 method;
6673 	u32 interval;
6674 	__be32 src_ip4_addr;
6675 	__be32 dest_ip4_addr;
6676 	const u8 dest_mac_addr[ETH_ALEN];
6677 };
6678 
6679 enum wmi_force_fw_hang_type {
6680 	WMI_FORCE_FW_HANG_ASSERT = 1,
6681 	WMI_FORCE_FW_HANG_NO_DETECT,
6682 	WMI_FORCE_FW_HANG_CTRL_EP_FULL,
6683 	WMI_FORCE_FW_HANG_EMPTY_POINT,
6684 	WMI_FORCE_FW_HANG_STACK_OVERFLOW,
6685 	WMI_FORCE_FW_HANG_INFINITE_LOOP,
6686 };
6687 
6688 #define WMI_FORCE_FW_HANG_RANDOM_TIME 0xFFFFFFFF
6689 
6690 struct wmi_force_fw_hang_cmd {
6691 	__le32 type;
6692 	__le32 delay_ms;
6693 } __packed;
6694 
6695 enum wmi_pdev_reset_mode_type {
6696 	WMI_RST_MODE_TX_FLUSH = 1,
6697 	WMI_RST_MODE_WARM_RESET,
6698 	WMI_RST_MODE_COLD_RESET,
6699 	WMI_RST_MODE_WARM_RESET_RESTORE_CAL,
6700 	WMI_RST_MODE_COLD_RESET_RESTORE_CAL,
6701 	WMI_RST_MODE_MAX,
6702 };
6703 
6704 enum ath10k_dbglog_level {
6705 	ATH10K_DBGLOG_LEVEL_VERBOSE = 0,
6706 	ATH10K_DBGLOG_LEVEL_INFO = 1,
6707 	ATH10K_DBGLOG_LEVEL_WARN = 2,
6708 	ATH10K_DBGLOG_LEVEL_ERR = 3,
6709 };
6710 
6711 /* VAP ids to enable dbglog */
6712 #define ATH10K_DBGLOG_CFG_VAP_LOG_LSB		0
6713 #define ATH10K_DBGLOG_CFG_VAP_LOG_MASK		0x0000ffff
6714 
6715 /* to enable dbglog in the firmware */
6716 #define ATH10K_DBGLOG_CFG_REPORTING_ENABLE_LSB	16
6717 #define ATH10K_DBGLOG_CFG_REPORTING_ENABLE_MASK	0x00010000
6718 
6719 /* timestamp resolution */
6720 #define ATH10K_DBGLOG_CFG_RESOLUTION_LSB	17
6721 #define ATH10K_DBGLOG_CFG_RESOLUTION_MASK	0x000E0000
6722 
6723 /* number of queued messages before sending them to the host */
6724 #define ATH10K_DBGLOG_CFG_REPORT_SIZE_LSB	20
6725 #define ATH10K_DBGLOG_CFG_REPORT_SIZE_MASK	0x0ff00000
6726 
6727 /*
6728  * Log levels to enable. This defines the minimum level to enable, this is
6729  * not a bitmask. See enum ath10k_dbglog_level for the values.
6730  */
6731 #define ATH10K_DBGLOG_CFG_LOG_LVL_LSB		28
6732 #define ATH10K_DBGLOG_CFG_LOG_LVL_MASK		0x70000000
6733 
6734 /*
6735  * Note: this is a cleaned up version of a struct firmware uses. For
6736  * example, config_valid was hidden inside an array.
6737  */
6738 struct wmi_dbglog_cfg_cmd {
6739 	/* bitmask to hold mod id config*/
6740 	__le32 module_enable;
6741 
6742 	/* see ATH10K_DBGLOG_CFG_ */
6743 	__le32 config_enable;
6744 
6745 	/* mask of module id bits to be changed */
6746 	__le32 module_valid;
6747 
6748 	/* mask of config bits to be changed, see ATH10K_DBGLOG_CFG_ */
6749 	__le32 config_valid;
6750 } __packed;
6751 
6752 struct wmi_10_4_dbglog_cfg_cmd {
6753 	/* bitmask to hold mod id config*/
6754 	__le64 module_enable;
6755 
6756 	/* see ATH10K_DBGLOG_CFG_ */
6757 	__le32 config_enable;
6758 
6759 	/* mask of module id bits to be changed */
6760 	__le64 module_valid;
6761 
6762 	/* mask of config bits to be changed, see ATH10K_DBGLOG_CFG_ */
6763 	__le32 config_valid;
6764 } __packed;
6765 
6766 enum wmi_roam_reason {
6767 	WMI_ROAM_REASON_BETTER_AP = 1,
6768 	WMI_ROAM_REASON_BEACON_MISS = 2,
6769 	WMI_ROAM_REASON_LOW_RSSI = 3,
6770 	WMI_ROAM_REASON_SUITABLE_AP_FOUND = 4,
6771 	WMI_ROAM_REASON_HO_FAILED = 5,
6772 
6773 	/* keep last */
6774 	WMI_ROAM_REASON_MAX,
6775 };
6776 
6777 struct wmi_roam_ev {
6778 	__le32 vdev_id;
6779 	__le32 reason;
6780 } __packed;
6781 
6782 #define ATH10K_FRAGMT_THRESHOLD_MIN	540
6783 #define ATH10K_FRAGMT_THRESHOLD_MAX	2346
6784 
6785 #define WMI_MAX_EVENT 0x1000
6786 /* Maximum number of pending TXed WMI packets */
6787 #define WMI_SKB_HEADROOM sizeof(struct wmi_cmd_hdr)
6788 
6789 /* By default disable power save for IBSS */
6790 #define ATH10K_DEFAULT_ATIM 0
6791 
6792 #define WMI_MAX_MEM_REQS 16
6793 
6794 struct wmi_scan_ev_arg {
6795 	__le32 event_type; /* %WMI_SCAN_EVENT_ */
6796 	__le32 reason; /* %WMI_SCAN_REASON_ */
6797 	__le32 channel_freq; /* only valid for WMI_SCAN_EVENT_FOREIGN_CHANNEL */
6798 	__le32 scan_req_id;
6799 	__le32 scan_id;
6800 	__le32 vdev_id;
6801 };
6802 
6803 struct mgmt_tx_compl_params {
6804 	u32 desc_id;
6805 	u32 status;
6806 	u32 ppdu_id;
6807 	int ack_rssi;
6808 };
6809 
6810 struct wmi_tlv_mgmt_tx_compl_ev_arg {
6811 	__le32 desc_id;
6812 	__le32 status;
6813 	__le32 pdev_id;
6814 	__le32 ppdu_id;
6815 	__le32 ack_rssi;
6816 };
6817 
6818 struct wmi_tlv_mgmt_tx_bundle_compl_ev_arg {
6819 	__le32 num_reports;
6820 	const __le32 *desc_ids;
6821 	const __le32 *status;
6822 	const __le32 *ppdu_ids;
6823 	const __le32 *ack_rssi;
6824 };
6825 
6826 struct wmi_peer_delete_resp_ev_arg {
6827 	__le32 vdev_id;
6828 	struct wmi_mac_addr peer_addr;
6829 };
6830 
6831 #define WMI_MGMT_RX_NUM_RSSI 4
6832 struct wmi_mgmt_rx_ev_arg {
6833 	__le32 channel;
6834 	__le32 snr;
6835 	__le32 rate;
6836 	__le32 phy_mode;
6837 	__le32 buf_len;
6838 	__le32 status; /* %WMI_RX_STATUS_ */
6839 	struct wmi_mgmt_rx_ext_info ext_info;
6840 	__le32 rssi[WMI_MGMT_RX_NUM_RSSI];
6841 };
6842 
6843 struct wmi_ch_info_ev_arg {
6844 	__le32 err_code;
6845 	__le32 freq;
6846 	__le32 cmd_flags;
6847 	__le32 noise_floor;
6848 	__le32 rx_clear_count;
6849 	__le32 cycle_count;
6850 	__le32 chan_tx_pwr_range;
6851 	__le32 chan_tx_pwr_tp;
6852 	__le32 rx_frame_count;
6853 	__le32 my_bss_rx_cycle_count;
6854 	__le32 rx_11b_mode_data_duration;
6855 	__le32 tx_frame_cnt;
6856 	__le32 mac_clk_mhz;
6857 };
6858 
6859 /* From 10.4 firmware, not sure all have the same values. */
6860 enum wmi_vdev_start_status {
6861 	WMI_VDEV_START_OK = 0,
6862 	WMI_VDEV_START_CHAN_INVALID,
6863 };
6864 
6865 struct wmi_vdev_start_ev_arg {
6866 	__le32 vdev_id;
6867 	__le32 req_id;
6868 	__le32 resp_type; /* %WMI_VDEV_RESP_ */
6869 	__le32 status; /* See wmi_vdev_start_status enum above */
6870 };
6871 
6872 struct wmi_peer_kick_ev_arg {
6873 	const u8 *mac_addr;
6874 };
6875 
6876 struct wmi_swba_ev_arg {
6877 	__le32 vdev_map;
6878 	struct wmi_tim_info_arg tim_info[WMI_MAX_AP_VDEV];
6879 	const struct wmi_p2p_noa_info *noa_info[WMI_MAX_AP_VDEV];
6880 };
6881 
6882 struct wmi_phyerr_ev_arg {
6883 	u32 tsf_timestamp;
6884 	u16 freq1;
6885 	u16 freq2;
6886 	u8 rssi_combined;
6887 	u8 chan_width_mhz;
6888 	u8 phy_err_code;
6889 	u16 nf_chains[4];
6890 	u32 buf_len;
6891 	const u8 *buf;
6892 	u8 hdr_len;
6893 };
6894 
6895 struct wmi_phyerr_hdr_arg {
6896 	u32 num_phyerrs;
6897 	u32 tsf_l32;
6898 	u32 tsf_u32;
6899 	u32 buf_len;
6900 	const void *phyerrs;
6901 };
6902 
6903 struct wmi_dfs_status_ev_arg {
6904 	u32 status;
6905 };
6906 
6907 struct wmi_svc_rdy_ev_arg {
6908 	__le32 min_tx_power;
6909 	__le32 max_tx_power;
6910 	__le32 ht_cap;
6911 	__le32 vht_cap;
6912 	__le32 vht_supp_mcs;
6913 	__le32 sw_ver0;
6914 	__le32 sw_ver1;
6915 	__le32 fw_build;
6916 	__le32 phy_capab;
6917 	__le32 num_rf_chains;
6918 	__le32 eeprom_rd;
6919 	__le32 num_mem_reqs;
6920 	__le32 low_2ghz_chan;
6921 	__le32 high_2ghz_chan;
6922 	__le32 low_5ghz_chan;
6923 	__le32 high_5ghz_chan;
6924 	__le32 sys_cap_info;
6925 	const __le32 *service_map;
6926 	size_t service_map_len;
6927 	const struct wlan_host_mem_req *mem_reqs[WMI_MAX_MEM_REQS];
6928 };
6929 
6930 struct wmi_svc_avail_ev_arg {
6931 	bool service_map_ext_valid;
6932 	__le32 service_map_ext_len;
6933 	const __le32 *service_map_ext;
6934 };
6935 
6936 struct wmi_rdy_ev_arg {
6937 	__le32 sw_version;
6938 	__le32 abi_version;
6939 	__le32 status;
6940 	const u8 *mac_addr;
6941 };
6942 
6943 struct wmi_roam_ev_arg {
6944 	__le32 vdev_id;
6945 	__le32 reason;
6946 	__le32 rssi;
6947 };
6948 
6949 struct wmi_echo_ev_arg {
6950 	__le32 value;
6951 };
6952 
6953 struct wmi_pdev_temperature_event {
6954 	/* temperature value in Celsius degree */
6955 	__le32 temperature;
6956 } __packed;
6957 
6958 struct wmi_pdev_bss_chan_info_event {
6959 	__le32 freq;
6960 	__le32 noise_floor;
6961 	__le64 cycle_busy;
6962 	__le64 cycle_total;
6963 	__le64 cycle_tx;
6964 	__le64 cycle_rx;
6965 	__le64 cycle_rx_bss;
6966 	__le32 reserved;
6967 } __packed;
6968 
6969 /* WOW structures */
6970 enum wmi_wow_wakeup_event {
6971 	WOW_BMISS_EVENT = 0,
6972 	WOW_BETTER_AP_EVENT,
6973 	WOW_DEAUTH_RECVD_EVENT,
6974 	WOW_MAGIC_PKT_RECVD_EVENT,
6975 	WOW_GTK_ERR_EVENT,
6976 	WOW_FOURWAY_HSHAKE_EVENT,
6977 	WOW_EAPOL_RECVD_EVENT,
6978 	WOW_NLO_DETECTED_EVENT,
6979 	WOW_DISASSOC_RECVD_EVENT,
6980 	WOW_PATTERN_MATCH_EVENT,
6981 	WOW_CSA_IE_EVENT,
6982 	WOW_PROBE_REQ_WPS_IE_EVENT,
6983 	WOW_AUTH_REQ_EVENT,
6984 	WOW_ASSOC_REQ_EVENT,
6985 	WOW_HTT_EVENT,
6986 	WOW_RA_MATCH_EVENT,
6987 	WOW_HOST_AUTO_SHUTDOWN_EVENT,
6988 	WOW_IOAC_MAGIC_EVENT,
6989 	WOW_IOAC_SHORT_EVENT,
6990 	WOW_IOAC_EXTEND_EVENT,
6991 	WOW_IOAC_TIMER_EVENT,
6992 	WOW_DFS_PHYERR_RADAR_EVENT,
6993 	WOW_BEACON_EVENT,
6994 	WOW_CLIENT_KICKOUT_EVENT,
6995 	WOW_EVENT_MAX,
6996 };
6997 
6998 #define C2S(x) case x: return #x
6999 
wow_wakeup_event(enum wmi_wow_wakeup_event ev)7000 static inline const char *wow_wakeup_event(enum wmi_wow_wakeup_event ev)
7001 {
7002 	switch (ev) {
7003 	C2S(WOW_BMISS_EVENT);
7004 	C2S(WOW_BETTER_AP_EVENT);
7005 	C2S(WOW_DEAUTH_RECVD_EVENT);
7006 	C2S(WOW_MAGIC_PKT_RECVD_EVENT);
7007 	C2S(WOW_GTK_ERR_EVENT);
7008 	C2S(WOW_FOURWAY_HSHAKE_EVENT);
7009 	C2S(WOW_EAPOL_RECVD_EVENT);
7010 	C2S(WOW_NLO_DETECTED_EVENT);
7011 	C2S(WOW_DISASSOC_RECVD_EVENT);
7012 	C2S(WOW_PATTERN_MATCH_EVENT);
7013 	C2S(WOW_CSA_IE_EVENT);
7014 	C2S(WOW_PROBE_REQ_WPS_IE_EVENT);
7015 	C2S(WOW_AUTH_REQ_EVENT);
7016 	C2S(WOW_ASSOC_REQ_EVENT);
7017 	C2S(WOW_HTT_EVENT);
7018 	C2S(WOW_RA_MATCH_EVENT);
7019 	C2S(WOW_HOST_AUTO_SHUTDOWN_EVENT);
7020 	C2S(WOW_IOAC_MAGIC_EVENT);
7021 	C2S(WOW_IOAC_SHORT_EVENT);
7022 	C2S(WOW_IOAC_EXTEND_EVENT);
7023 	C2S(WOW_IOAC_TIMER_EVENT);
7024 	C2S(WOW_DFS_PHYERR_RADAR_EVENT);
7025 	C2S(WOW_BEACON_EVENT);
7026 	C2S(WOW_CLIENT_KICKOUT_EVENT);
7027 	C2S(WOW_EVENT_MAX);
7028 	default:
7029 		return NULL;
7030 	}
7031 }
7032 
7033 enum wmi_wow_wake_reason {
7034 	WOW_REASON_UNSPECIFIED = -1,
7035 	WOW_REASON_NLOD = 0,
7036 	WOW_REASON_AP_ASSOC_LOST,
7037 	WOW_REASON_LOW_RSSI,
7038 	WOW_REASON_DEAUTH_RECVD,
7039 	WOW_REASON_DISASSOC_RECVD,
7040 	WOW_REASON_GTK_HS_ERR,
7041 	WOW_REASON_EAP_REQ,
7042 	WOW_REASON_FOURWAY_HS_RECV,
7043 	WOW_REASON_TIMER_INTR_RECV,
7044 	WOW_REASON_PATTERN_MATCH_FOUND,
7045 	WOW_REASON_RECV_MAGIC_PATTERN,
7046 	WOW_REASON_P2P_DISC,
7047 	WOW_REASON_WLAN_HB,
7048 	WOW_REASON_CSA_EVENT,
7049 	WOW_REASON_PROBE_REQ_WPS_IE_RECV,
7050 	WOW_REASON_AUTH_REQ_RECV,
7051 	WOW_REASON_ASSOC_REQ_RECV,
7052 	WOW_REASON_HTT_EVENT,
7053 	WOW_REASON_RA_MATCH,
7054 	WOW_REASON_HOST_AUTO_SHUTDOWN,
7055 	WOW_REASON_IOAC_MAGIC_EVENT,
7056 	WOW_REASON_IOAC_SHORT_EVENT,
7057 	WOW_REASON_IOAC_EXTEND_EVENT,
7058 	WOW_REASON_IOAC_TIMER_EVENT,
7059 	WOW_REASON_ROAM_HO,
7060 	WOW_REASON_DFS_PHYERR_RADADR_EVENT,
7061 	WOW_REASON_BEACON_RECV,
7062 	WOW_REASON_CLIENT_KICKOUT_EVENT,
7063 	WOW_REASON_DEBUG_TEST = 0xFF,
7064 };
7065 
wow_reason(enum wmi_wow_wake_reason reason)7066 static inline const char *wow_reason(enum wmi_wow_wake_reason reason)
7067 {
7068 	switch (reason) {
7069 	C2S(WOW_REASON_UNSPECIFIED);
7070 	C2S(WOW_REASON_NLOD);
7071 	C2S(WOW_REASON_AP_ASSOC_LOST);
7072 	C2S(WOW_REASON_LOW_RSSI);
7073 	C2S(WOW_REASON_DEAUTH_RECVD);
7074 	C2S(WOW_REASON_DISASSOC_RECVD);
7075 	C2S(WOW_REASON_GTK_HS_ERR);
7076 	C2S(WOW_REASON_EAP_REQ);
7077 	C2S(WOW_REASON_FOURWAY_HS_RECV);
7078 	C2S(WOW_REASON_TIMER_INTR_RECV);
7079 	C2S(WOW_REASON_PATTERN_MATCH_FOUND);
7080 	C2S(WOW_REASON_RECV_MAGIC_PATTERN);
7081 	C2S(WOW_REASON_P2P_DISC);
7082 	C2S(WOW_REASON_WLAN_HB);
7083 	C2S(WOW_REASON_CSA_EVENT);
7084 	C2S(WOW_REASON_PROBE_REQ_WPS_IE_RECV);
7085 	C2S(WOW_REASON_AUTH_REQ_RECV);
7086 	C2S(WOW_REASON_ASSOC_REQ_RECV);
7087 	C2S(WOW_REASON_HTT_EVENT);
7088 	C2S(WOW_REASON_RA_MATCH);
7089 	C2S(WOW_REASON_HOST_AUTO_SHUTDOWN);
7090 	C2S(WOW_REASON_IOAC_MAGIC_EVENT);
7091 	C2S(WOW_REASON_IOAC_SHORT_EVENT);
7092 	C2S(WOW_REASON_IOAC_EXTEND_EVENT);
7093 	C2S(WOW_REASON_IOAC_TIMER_EVENT);
7094 	C2S(WOW_REASON_ROAM_HO);
7095 	C2S(WOW_REASON_DFS_PHYERR_RADADR_EVENT);
7096 	C2S(WOW_REASON_BEACON_RECV);
7097 	C2S(WOW_REASON_CLIENT_KICKOUT_EVENT);
7098 	C2S(WOW_REASON_DEBUG_TEST);
7099 	default:
7100 		return NULL;
7101 	}
7102 }
7103 
7104 #undef C2S
7105 
7106 struct wmi_wow_ev_arg {
7107 	u32 vdev_id;
7108 	u32 flag;
7109 	enum wmi_wow_wake_reason wake_reason;
7110 	u32 data_len;
7111 };
7112 
7113 #define WOW_MIN_PATTERN_SIZE	1
7114 #define WOW_MAX_PATTERN_SIZE	148
7115 #define WOW_MAX_PKT_OFFSET	128
7116 #define WOW_HDR_LEN	(sizeof(struct ieee80211_hdr_3addr) + \
7117 	sizeof(struct rfc1042_hdr))
7118 #define WOW_MAX_REDUCE	(WOW_HDR_LEN - sizeof(struct ethhdr) - \
7119 	offsetof(struct ieee80211_hdr_3addr, addr1))
7120 
7121 enum wmi_tdls_state {
7122 	WMI_TDLS_DISABLE,
7123 	WMI_TDLS_ENABLE_PASSIVE,
7124 	WMI_TDLS_ENABLE_ACTIVE,
7125 	WMI_TDLS_ENABLE_ACTIVE_EXTERNAL_CONTROL,
7126 };
7127 
7128 enum wmi_tdls_peer_state {
7129 	WMI_TDLS_PEER_STATE_PEERING,
7130 	WMI_TDLS_PEER_STATE_CONNECTED,
7131 	WMI_TDLS_PEER_STATE_TEARDOWN,
7132 };
7133 
7134 struct wmi_tdls_peer_update_cmd_arg {
7135 	u32 vdev_id;
7136 	enum wmi_tdls_peer_state peer_state;
7137 	u8 addr[ETH_ALEN];
7138 };
7139 
7140 #define WMI_TDLS_MAX_SUPP_OPER_CLASSES 32
7141 
7142 #define WMI_TDLS_PEER_SP_MASK	0x60
7143 #define WMI_TDLS_PEER_SP_LSB	5
7144 
7145 enum wmi_tdls_options {
7146 	WMI_TDLS_OFFCHAN_EN = BIT(0),
7147 	WMI_TDLS_BUFFER_STA_EN = BIT(1),
7148 	WMI_TDLS_SLEEP_STA_EN = BIT(2),
7149 };
7150 
7151 enum {
7152 	WMI_TDLS_PEER_QOS_AC_VO = BIT(0),
7153 	WMI_TDLS_PEER_QOS_AC_VI = BIT(1),
7154 	WMI_TDLS_PEER_QOS_AC_BK = BIT(2),
7155 	WMI_TDLS_PEER_QOS_AC_BE = BIT(3),
7156 };
7157 
7158 struct wmi_tdls_peer_capab_arg {
7159 	u8 peer_uapsd_queues;
7160 	u8 peer_max_sp;
7161 	u32 buff_sta_support;
7162 	u32 off_chan_support;
7163 	u32 peer_curr_operclass;
7164 	u32 self_curr_operclass;
7165 	u32 peer_chan_len;
7166 	u32 peer_operclass_len;
7167 	u8 peer_operclass[WMI_TDLS_MAX_SUPP_OPER_CLASSES];
7168 	u32 is_peer_responder;
7169 	u32 pref_offchan_num;
7170 	u32 pref_offchan_bw;
7171 };
7172 
7173 struct wmi_10_4_tdls_set_state_cmd {
7174 	__le32 vdev_id;
7175 	__le32 state;
7176 	__le32 notification_interval_ms;
7177 	__le32 tx_discovery_threshold;
7178 	__le32 tx_teardown_threshold;
7179 	__le32 rssi_teardown_threshold;
7180 	__le32 rssi_delta;
7181 	__le32 tdls_options;
7182 	__le32 tdls_peer_traffic_ind_window;
7183 	__le32 tdls_peer_traffic_response_timeout_ms;
7184 	__le32 tdls_puapsd_mask;
7185 	__le32 tdls_puapsd_inactivity_time_ms;
7186 	__le32 tdls_puapsd_rx_frame_threshold;
7187 	__le32 teardown_notification_ms;
7188 	__le32 tdls_peer_kickout_threshold;
7189 } __packed;
7190 
7191 struct wmi_tdls_peer_capabilities {
7192 	__le32 peer_qos;
7193 	__le32 buff_sta_support;
7194 	__le32 off_chan_support;
7195 	__le32 peer_curr_operclass;
7196 	__le32 self_curr_operclass;
7197 	__le32 peer_chan_len;
7198 	__le32 peer_operclass_len;
7199 	u8 peer_operclass[WMI_TDLS_MAX_SUPP_OPER_CLASSES];
7200 	__le32 is_peer_responder;
7201 	__le32 pref_offchan_num;
7202 	__le32 pref_offchan_bw;
7203 	union {
7204 		/* to match legacy implementation allocate room for
7205 		 * at least one record even if peer_chan_len is 0
7206 		 */
7207 		struct wmi_channel peer_chan_min_allocation;
7208 		DECLARE_FLEX_ARRAY(struct wmi_channel, peer_chan_list);
7209 	};
7210 } __packed;
7211 
7212 struct wmi_10_4_tdls_peer_update_cmd {
7213 	__le32 vdev_id;
7214 	struct wmi_mac_addr peer_macaddr;
7215 	__le32 peer_state;
7216 	__le32 reserved[4];
7217 	struct wmi_tdls_peer_capabilities peer_capab;
7218 } __packed;
7219 
7220 enum wmi_tdls_peer_reason {
7221 	WMI_TDLS_TEARDOWN_REASON_TX,
7222 	WMI_TDLS_TEARDOWN_REASON_RSSI,
7223 	WMI_TDLS_TEARDOWN_REASON_SCAN,
7224 	WMI_TDLS_DISCONNECTED_REASON_PEER_DELETE,
7225 	WMI_TDLS_TEARDOWN_REASON_PTR_TIMEOUT,
7226 	WMI_TDLS_TEARDOWN_REASON_BAD_PTR,
7227 	WMI_TDLS_TEARDOWN_REASON_NO_RESPONSE,
7228 	WMI_TDLS_ENTER_BUF_STA,
7229 	WMI_TDLS_EXIT_BUF_STA,
7230 	WMI_TDLS_ENTER_BT_BUSY_MODE,
7231 	WMI_TDLS_EXIT_BT_BUSY_MODE,
7232 	WMI_TDLS_SCAN_STARTED_EVENT,
7233 	WMI_TDLS_SCAN_COMPLETED_EVENT,
7234 };
7235 
7236 enum wmi_tdls_peer_notification {
7237 	WMI_TDLS_SHOULD_DISCOVER,
7238 	WMI_TDLS_SHOULD_TEARDOWN,
7239 	WMI_TDLS_PEER_DISCONNECTED,
7240 	WMI_TDLS_CONNECTION_TRACKER_NOTIFICATION,
7241 };
7242 
7243 struct wmi_tdls_peer_event {
7244 	struct wmi_mac_addr peer_macaddr;
7245 	/* see enum wmi_tdls_peer_notification*/
7246 	__le32 peer_status;
7247 	/* see enum wmi_tdls_peer_reason */
7248 	__le32 peer_reason;
7249 	__le32 vdev_id;
7250 } __packed;
7251 
7252 enum wmi_tid_aggr_control_conf {
7253 	WMI_TID_CONFIG_AGGR_CONTROL_IGNORE,
7254 	WMI_TID_CONFIG_AGGR_CONTROL_ENABLE,
7255 	WMI_TID_CONFIG_AGGR_CONTROL_DISABLE,
7256 };
7257 
7258 enum wmi_noack_tid_conf {
7259 	WMI_NOACK_TID_CONFIG_IGNORE_ACK_POLICY,
7260 	WMI_PEER_TID_CONFIG_ACK,
7261 	WMI_PEER_TID_CONFIG_NOACK,
7262 };
7263 
7264 enum wmi_tid_rate_ctrl_conf {
7265 	WMI_TID_CONFIG_RATE_CONTROL_IGNORE,
7266 	WMI_TID_CONFIG_RATE_CONTROL_AUTO,
7267 	WMI_TID_CONFIG_RATE_CONTROL_FIXED_RATE,
7268 	WMI_TID_CONFIG_RATE_CONTROL_DEFAULT_LOWEST_RATE,
7269 	WMI_PEER_TID_CONFIG_RATE_UPPER_CAP,
7270 };
7271 
7272 enum wmi_tid_rtscts_control_conf {
7273 	WMI_TID_CONFIG_RTSCTS_CONTROL_ENABLE,
7274 	WMI_TID_CONFIG_RTSCTS_CONTROL_DISABLE,
7275 };
7276 
7277 enum wmi_ext_tid_config_map {
7278 	WMI_EXT_TID_RTS_CTS_CONFIG = BIT(0),
7279 };
7280 
7281 struct wmi_per_peer_per_tid_cfg_arg {
7282 	u32 vdev_id;
7283 	struct wmi_mac_addr peer_macaddr;
7284 	u32 tid;
7285 	enum wmi_noack_tid_conf ack_policy;
7286 	enum wmi_tid_aggr_control_conf aggr_control;
7287 	u8 rate_ctrl;
7288 	u32 retry_count;
7289 	u32 rcode_flags;
7290 	u32 ext_tid_cfg_bitmap;
7291 	u32 rtscts_ctrl;
7292 };
7293 
7294 struct wmi_peer_per_tid_cfg_cmd {
7295 	__le32 vdev_id;
7296 	struct wmi_mac_addr peer_macaddr;
7297 	__le32 tid;
7298 
7299 	/* see enum wmi_noack_tid_conf */
7300 	__le32 ack_policy;
7301 
7302 	/* see enum wmi_tid_aggr_control_conf */
7303 	__le32 aggr_control;
7304 
7305 	/* see enum wmi_tid_rate_ctrl_conf */
7306 	__le32 rate_control;
7307 	__le32 rcode_flags;
7308 	__le32 retry_count;
7309 
7310 	/* See enum wmi_ext_tid_config_map */
7311 	__le32 ext_tid_cfg_bitmap;
7312 
7313 	/* see enum wmi_tid_rtscts_control_conf */
7314 	__le32 rtscts_ctrl;
7315 } __packed;
7316 
7317 enum wmi_txbf_conf {
7318 	WMI_TXBF_CONF_UNSUPPORTED,
7319 	WMI_TXBF_CONF_BEFORE_ASSOC,
7320 	WMI_TXBF_CONF_AFTER_ASSOC,
7321 };
7322 
7323 #define	WMI_CCA_DETECT_LEVEL_AUTO	0
7324 #define	WMI_CCA_DETECT_MARGIN_AUTO	0
7325 
7326 struct wmi_pdev_set_adaptive_cca_params {
7327 	__le32 enable;
7328 	__le32 cca_detect_level;
7329 	__le32 cca_detect_margin;
7330 } __packed;
7331 
7332 #define WMI_PNO_MAX_SCHED_SCAN_PLANS      2
7333 #define WMI_PNO_MAX_SCHED_SCAN_PLAN_INT   7200
7334 #define WMI_PNO_MAX_SCHED_SCAN_PLAN_ITRNS 100
7335 #define WMI_PNO_MAX_NETW_CHANNELS         26
7336 #define WMI_PNO_MAX_NETW_CHANNELS_EX      60
7337 #define WMI_PNO_MAX_SUPP_NETWORKS         WLAN_SCAN_PARAMS_MAX_SSID
7338 #define WMI_PNO_MAX_IE_LENGTH             WLAN_SCAN_PARAMS_MAX_IE_LEN
7339 
7340 /*size based of dot11 declaration without extra IEs as we will not carry those for PNO*/
7341 #define WMI_PNO_MAX_PB_REQ_SIZE    450
7342 
7343 #define WMI_PNO_24G_DEFAULT_CH     1
7344 #define WMI_PNO_5G_DEFAULT_CH      36
7345 
7346 #define WMI_ACTIVE_MAX_CHANNEL_TIME 40
7347 #define WMI_PASSIVE_MAX_CHANNEL_TIME   110
7348 
7349 /* SSID broadcast type */
7350 enum wmi_SSID_bcast_type {
7351 	BCAST_UNKNOWN      = 0,
7352 	BCAST_NORMAL       = 1,
7353 	BCAST_HIDDEN       = 2,
7354 };
7355 
7356 struct wmi_network_type {
7357 	struct wmi_ssid ssid;
7358 	u32 authentication;
7359 	u32 encryption;
7360 	u32 bcast_nw_type;
7361 	u8 channel_count;
7362 	u16 channels[WMI_PNO_MAX_NETW_CHANNELS_EX];
7363 	s32 rssi_threshold;
7364 } __packed;
7365 
7366 struct wmi_pno_scan_req {
7367 	u8 enable;
7368 	u8 vdev_id;
7369 	u8 uc_networks_count;
7370 	struct wmi_network_type a_networks[WMI_PNO_MAX_SUPP_NETWORKS];
7371 	u32 fast_scan_period;
7372 	u32 slow_scan_period;
7373 	u8 fast_scan_max_cycles;
7374 
7375 	bool do_passive_scan;
7376 
7377 	u32 delay_start_time;
7378 	u32 active_min_time;
7379 	u32 active_max_time;
7380 	u32 passive_min_time;
7381 	u32 passive_max_time;
7382 
7383 	/* mac address randomization attributes */
7384 	u32 enable_pno_scan_randomization;
7385 	u8 mac_addr[ETH_ALEN];
7386 	u8 mac_addr_mask[ETH_ALEN];
7387 } __packed;
7388 
7389 enum wmi_host_platform_type {
7390 	WMI_HOST_PLATFORM_HIGH_PERF,
7391 	WMI_HOST_PLATFORM_LOW_PERF,
7392 };
7393 
7394 enum wmi_bss_survey_req_type {
7395 	WMI_BSS_SURVEY_REQ_TYPE_READ = 1,
7396 	WMI_BSS_SURVEY_REQ_TYPE_READ_CLEAR,
7397 };
7398 
7399 struct wmi_pdev_chan_info_req_cmd {
7400 	__le32 type;
7401 	__le32 reserved;
7402 } __packed;
7403 
7404 /* bb timing register configurations */
7405 struct wmi_bb_timing_cfg_arg {
7406 	/* Tx_end to pa off timing */
7407 	u32 bb_tx_timing;
7408 
7409 	/* Tx_end to external pa off timing */
7410 	u32 bb_xpa_timing;
7411 };
7412 
7413 struct wmi_pdev_bb_timing_cfg_cmd {
7414 	/* Tx_end to pa off timing */
7415 	__le32 bb_tx_timing;
7416 
7417 	/* Tx_end to external pa off timing */
7418 	__le32 bb_xpa_timing;
7419 } __packed;
7420 
7421 struct ath10k;
7422 struct ath10k_vif;
7423 struct ath10k_fw_stats_pdev;
7424 struct ath10k_fw_stats_peer;
7425 struct ath10k_fw_stats;
7426 
7427 int ath10k_wmi_attach(struct ath10k *ar);
7428 void ath10k_wmi_detach(struct ath10k *ar);
7429 void ath10k_wmi_free_host_mem(struct ath10k *ar);
7430 int ath10k_wmi_wait_for_service_ready(struct ath10k *ar);
7431 int ath10k_wmi_wait_for_unified_ready(struct ath10k *ar);
7432 
7433 struct sk_buff *ath10k_wmi_alloc_skb(struct ath10k *ar, u32 len);
7434 int ath10k_wmi_connect(struct ath10k *ar);
7435 
7436 int ath10k_wmi_cmd_send(struct ath10k *ar, struct sk_buff *skb, u32 cmd_id);
7437 int ath10k_wmi_cmd_send_nowait(struct ath10k *ar, struct sk_buff *skb,
7438 			       u32 cmd_id);
7439 void ath10k_wmi_start_scan_init(struct ath10k *ar, struct wmi_start_scan_arg *arg);
7440 
7441 void ath10k_wmi_pull_pdev_stats_base(const struct wmi_pdev_stats_base *src,
7442 				     struct ath10k_fw_stats_pdev *dst);
7443 void ath10k_wmi_pull_pdev_stats_tx(const struct wmi_pdev_stats_tx *src,
7444 				   struct ath10k_fw_stats_pdev *dst);
7445 void ath10k_wmi_pull_pdev_stats_rx(const struct wmi_pdev_stats_rx *src,
7446 				   struct ath10k_fw_stats_pdev *dst);
7447 void ath10k_wmi_pull_pdev_stats_extra(const struct wmi_pdev_stats_extra *src,
7448 				      struct ath10k_fw_stats_pdev *dst);
7449 void ath10k_wmi_pull_peer_stats(const struct wmi_peer_stats *src,
7450 				struct ath10k_fw_stats_peer *dst);
7451 void ath10k_wmi_put_host_mem_chunks(struct ath10k *ar,
7452 				    struct wmi_host_mem_chunks *chunks);
7453 void ath10k_wmi_put_start_scan_common(struct wmi_start_scan_common *cmn,
7454 				      const struct wmi_start_scan_arg *arg);
7455 void ath10k_wmi_set_wmm_param(struct wmi_wmm_params *params,
7456 			      const struct wmi_wmm_params_arg *arg);
7457 void ath10k_wmi_put_wmi_channel(struct ath10k *ar, struct wmi_channel *ch,
7458 				const struct wmi_channel_arg *arg);
7459 int ath10k_wmi_start_scan_verify(const struct wmi_start_scan_arg *arg);
7460 
7461 int ath10k_wmi_event_scan(struct ath10k *ar, struct sk_buff *skb);
7462 int ath10k_wmi_event_mgmt_rx(struct ath10k *ar, struct sk_buff *skb);
7463 int ath10k_wmi_event_mgmt_tx_compl(struct ath10k *ar, struct sk_buff *skb);
7464 int ath10k_wmi_event_mgmt_tx_bundle_compl(struct ath10k *ar, struct sk_buff *skb);
7465 void ath10k_wmi_event_chan_info(struct ath10k *ar, struct sk_buff *skb);
7466 void ath10k_wmi_event_echo(struct ath10k *ar, struct sk_buff *skb);
7467 int ath10k_wmi_event_debug_mesg(struct ath10k *ar, struct sk_buff *skb);
7468 void ath10k_wmi_event_update_stats(struct ath10k *ar, struct sk_buff *skb);
7469 void ath10k_wmi_event_vdev_start_resp(struct ath10k *ar, struct sk_buff *skb);
7470 void ath10k_wmi_event_vdev_stopped(struct ath10k *ar, struct sk_buff *skb);
7471 void ath10k_wmi_event_peer_sta_kickout(struct ath10k *ar, struct sk_buff *skb);
7472 void ath10k_wmi_event_host_swba(struct ath10k *ar, struct sk_buff *skb);
7473 void ath10k_wmi_event_tbttoffset_update(struct ath10k *ar, struct sk_buff *skb);
7474 void ath10k_wmi_event_dfs(struct ath10k *ar,
7475 			  struct wmi_phyerr_ev_arg *phyerr, u64 tsf);
7476 void ath10k_wmi_event_spectral_scan(struct ath10k *ar,
7477 				    struct wmi_phyerr_ev_arg *phyerr,
7478 				    u64 tsf);
7479 void ath10k_wmi_event_phyerr(struct ath10k *ar, struct sk_buff *skb);
7480 void ath10k_wmi_event_roam(struct ath10k *ar, struct sk_buff *skb);
7481 void ath10k_wmi_event_profile_match(struct ath10k *ar, struct sk_buff *skb);
7482 void ath10k_wmi_event_debug_print(struct ath10k *ar, struct sk_buff *skb);
7483 void ath10k_wmi_event_pdev_qvit(struct ath10k *ar, struct sk_buff *skb);
7484 void ath10k_wmi_event_wlan_profile_data(struct ath10k *ar, struct sk_buff *skb);
7485 void ath10k_wmi_event_rtt_measurement_report(struct ath10k *ar,
7486 					     struct sk_buff *skb);
7487 void ath10k_wmi_event_tsf_measurement_report(struct ath10k *ar,
7488 					     struct sk_buff *skb);
7489 void ath10k_wmi_event_rtt_error_report(struct ath10k *ar, struct sk_buff *skb);
7490 void ath10k_wmi_event_wow_wakeup_host(struct ath10k *ar, struct sk_buff *skb);
7491 void ath10k_wmi_event_dcs_interference(struct ath10k *ar, struct sk_buff *skb);
7492 void ath10k_wmi_event_pdev_tpc_config(struct ath10k *ar, struct sk_buff *skb);
7493 void ath10k_wmi_event_pdev_ftm_intg(struct ath10k *ar, struct sk_buff *skb);
7494 void ath10k_wmi_event_gtk_offload_status(struct ath10k *ar,
7495 					 struct sk_buff *skb);
7496 void ath10k_wmi_event_gtk_rekey_fail(struct ath10k *ar, struct sk_buff *skb);
7497 void ath10k_wmi_event_delba_complete(struct ath10k *ar, struct sk_buff *skb);
7498 void ath10k_wmi_event_addba_complete(struct ath10k *ar, struct sk_buff *skb);
7499 void ath10k_wmi_event_vdev_install_key_complete(struct ath10k *ar,
7500 						struct sk_buff *skb);
7501 void ath10k_wmi_event_inst_rssi_stats(struct ath10k *ar, struct sk_buff *skb);
7502 void ath10k_wmi_event_vdev_standby_req(struct ath10k *ar, struct sk_buff *skb);
7503 void ath10k_wmi_event_vdev_resume_req(struct ath10k *ar, struct sk_buff *skb);
7504 void ath10k_wmi_event_service_ready(struct ath10k *ar, struct sk_buff *skb);
7505 int ath10k_wmi_event_ready(struct ath10k *ar, struct sk_buff *skb);
7506 void ath10k_wmi_event_service_available(struct ath10k *ar, struct sk_buff *skb);
7507 int ath10k_wmi_op_pull_phyerr_ev(struct ath10k *ar, const void *phyerr_buf,
7508 				 int left_len, struct wmi_phyerr_ev_arg *arg);
7509 void ath10k_wmi_main_op_fw_stats_fill(struct ath10k *ar,
7510 				      struct ath10k_fw_stats *fw_stats,
7511 				      char *buf);
7512 void ath10k_wmi_10x_op_fw_stats_fill(struct ath10k *ar,
7513 				     struct ath10k_fw_stats *fw_stats,
7514 				     char *buf);
7515 void ath10k_wmi_10_4_op_fw_stats_fill(struct ath10k *ar,
7516 				      struct ath10k_fw_stats *fw_stats,
7517 				      char *buf);
7518 int ath10k_wmi_op_get_vdev_subtype(struct ath10k *ar,
7519 				   enum wmi_vdev_subtype subtype);
7520 int ath10k_wmi_barrier(struct ath10k *ar);
7521 void ath10k_wmi_tpc_config_get_rate_code(u8 *rate_code, u16 *pream_table,
7522 					 u32 num_tx_chain);
7523 void ath10k_wmi_event_tpc_final_table(struct ath10k *ar, struct sk_buff *skb);
7524 
7525 #endif /* _WMI_H_ */
7526