drivers/regulator/core.c

122 		rdev_err(rdev, "no constraints\n");
431 		rdev_err(rdev, "voltage operation not allowed\n");
441 		rdev_err(rdev, "unsupportable voltage range: %d-%duV\n",
481 		rdev_err(rdev, "Restricting voltage, %u-%uuV\n",
496 		rdev_err(rdev, "current operation not allowed\n");
507 		rdev_err(rdev, "unsupportable current range: %d-%duA\n",
526 		rdev_err(rdev, "invalid mode %x specified\n", *mode);
531 		rdev_err(rdev, "mode operation not allowed\n");
1002 			rdev_err(rdev, "failed to set load %d: %pe\n",
1048 			rdev_err(rdev, "failed to get optimum mode @ %d uA %d -> %d uV: %pe\n",
1055 			rdev_err(rdev, "failed to set optimum mode %x: %pe\n",
1077 		rdev_err(rdev, "failed to enabled/disable: %pe\n", ERR_PTR(ret));
1084 			rdev_err(rdev, "failed to set voltage: %pe\n", ERR_PTR(ret));
1092 			rdev_err(rdev, "failed to set mode: %pe\n", ERR_PTR(ret));
1227 				rdev_err(rdev,
1257 				rdev_err(rdev,
1292 			rdev_err(rdev, "invalid voltage constraints\n");
1317 			rdev_err(rdev,
1349 		rdev_err(rdev, "Invalid current constraints\n");
1362 		rdev_err(rdev, "Failed to set current constraint, %d\n", ret);
1446 			rdev_err(rdev, "failed to set input limit: %pe\n", ERR_PTR(ret));
1455 			rdev_err(rdev, "failed to set suspend state: %pe\n", ERR_PTR(ret));
1462 			rdev_err(rdev, "no set_mode operation\n");
1468 			rdev_err(rdev, "failed to set initial mode: %pe\n", ERR_PTR(ret));
1483 			rdev_err(rdev, "failed to set ramp_delay: %pe\n", ERR_PTR(ret));
1491 			rdev_err(rdev, "failed to set pull down: %pe\n", ERR_PTR(ret));
1499 			rdev_err(rdev, "failed to set soft start: %pe\n", ERR_PTR(ret));
1526 			rdev_err(rdev, "failed to set over current protection: %pe\n",
1538 			rdev_err(rdev, "failed to set over current limits: %pe\n",
1552 			rdev_err(rdev, "failed to set over voltage limits %pe\n",
1566 			rdev_err(rdev, "failed to set under voltage limits %pe\n",
1580 			rdev_err(rdev, "failed to set temperature limits %pe\n",
1594 			rdev_err(rdev, "failed to set active discharge: %pe\n", ERR_PTR(ret));
1644 			rdev_err(rdev, "failed to enable: %pe\n", ERR_PTR(ret));
2811 			rdev_err(rdev, "Enabled check timed out\n");
2876 		rdev_err(rdev, "Underflow of regulator enable count\n");
2932 			rdev_err(rdev, "is_enabled() failed: %pe\n", ERR_PTR(ret));
3036 					rdev_err(rdev, "failed to disable: %pe\n", ERR_PTR(ret));
3106 		rdev_err(rdev, "failed to force disable: %pe\n", ERR_PTR(ret));
3187 				rdev_err(rdev, "Deferred disable failed: %pe\n",
4241 		rdev_err(rdev, "Not all coupled regulators registered\n");
4344 		rdev_err(rdev, "The suspend voltage can't be changed!\n");
4556 				rdev_err(rdev,
5601 	rdev_err(rdev,
5626 			rdev_err(rdev, "coupler mismatch with %s\n",
5679 			rdev_err(rdev, "failed to detach from coupler: %pe\n",
5725 		rdev_err(rdev, "failed to get coupler: %pe\n", ERR_PTR(err));
5736 		rdev_err(rdev,
5742 		rdev_err(rdev,
5929 			rdev_err(rdev, "Failed to request enable GPIO: %pe\n",
6512 			rdev_err(rdev, "couldn't disable: %pe\n", ERR_PTR(ret));