Lines Matching full:lcd

20 	tristate "Character LCD core support" if COMPILE_TEST
22 	  This is the base system for character-based LCD displays.
25 	  This is some character LCD core interface that multiple drivers can
35 	tristate "Common functions for HD44780 (and compatibles) LCD displays" if COMPILE_TEST
45 	tristate "HD44780 Character LCD support"
50 	  The LCD is accessible through the /dev/lcd char device (10, 156).
56 	tristate "KS0108 LCD Controller"
60 	  If you have a LCD controlled by one or more KS0108
62 	  driver for your LCD.
74 	hex "Parallel port where the LCD is connected"
78 	  The address of the parallel port where the LCD is connected.
103 	  If your LCD seems to miss random writings, increment this.
111 	tristate "CFAG12864B LCD"
118 	  If you have a Crystalfontz 128x64 2-color LCD, cfag12864b Series,
119 	  say Y. You also need the ks0108 LCD Controller driver.
121 	  For help about how to wire your LCD to the parallel port,
126 	  The LCD framebuffer driver can be attached to a console.
140 	  Refresh rate of the LCD.
142 	  As the LCD is not memory mapped, the driver has to make the work by
148 	  You can freeze the computer, or the LCD maybe can't draw as fast as you
157 	tristate "Imagination Technologies ASCII LCD Display"
163 	  Enable this to support the simple ASCII LCD displays found on
191 	bool "ARM Ltd. Character LCD Driver"
194 	  This is a driver for the character LCD found on the ARM Ltd.
201 	tristate "Parallel port LCD/Keypad Panel support"
205 	  Say Y here if you have an HD44780 or KS-0074 LCD connected to your
206 	  parallel port. This driver also features 4 and 6-key keypads. The LCD
207 	  is accessible through the /dev/lcd char device (10, 156), and the
221 	  and LCD are connected to two separate ports, you have to start two
236 	    1 = 2x16 parallel LCD, old keypad
237 	    2 = 2x16 serial LCD (KS-0074), new keypad
238 	    3 = 2x16 parallel LCD (Hantronix), no keypad
239 	    4 = 2x16 parallel LCD (Nexcom NSA1045) with Nexcom's keypad
240 	    5 = 2x40 parallel LCD (old one), with old keypad
265 	int "LCD type (0=none, 1=custom, 2=old //, 3=ks0074, 4=hantronix, 5=Nexcom)"
269 	   This enables and configures an LCD connected to the parallel port.
271 	   '\e[L' which are specific to the LCD, and a few ANSI codes. The
273 	   under the name '/dev/lcd'. There are a total of 6 supported types :
277 	     2 : 2x16 & 2x40 parallel LCD (old wiring)
278 	     3 : 2x16 serial LCD (KS-0074 based)
279 	     4 : 2x16 parallel LCD (Hantronix wiring)
280 	     5 : 2x16 parallel LCD (Nexcom wiring)
288 	int "Number of lines on the LCD (1-2)"
292 	  This is the number of visible character lines on the LCD in custom profile.
297 	int "Number of characters per line on the LCD (1-40)"
301 	  This is the number of characters per line on the LCD in custom profile.
306 	int "Internal LCD line width (1-40, 40 by default)"
317 	  This option lets you configure the value used by your LCD in 'custom' profile.
322 	int "Hardware LCD line width (1-64, 64 by default)"
331 	  If you don't know what your LCD uses, in doubt let 16 here for a 2x16, and
336 	int "LCD character set (0=normal, 1=KS0074)"
352 	int "LCD communication mode (0=parallel 8 bits, 1=serial)"
356 	  This driver now supports any serial or parallel LCD wired to a parallel
358 	  be driving a serial LCD or a parallel one. Serial LCDs only use 2 wires
361 	  parallel LCD, and 1 for a serial LCD.
365 	int "Parallel port pin number & polarity connected to the LCD E signal (-17...17) "
369 	  This describes the number of the parallel port pin to which the LCD 'E'
380 	int "Parallel port pin number & polarity connected to the LCD RS signal (-17...17) "
384 	  This describes the number of the parallel port pin to which the LCD 'RS'
395 	int "Parallel port pin number & polarity connected to the LCD RW signal (-17...17) "
399 	  This describes the number of the parallel port pin to which the LCD 'RW'
410 	int "Parallel port pin number & polarity connected to the LCD SCL signal (-17...17) "
415 	  LCD 'SCL' signal has been connected. It can be :
425 	int "Parallel port pin number & polarity connected to the LCD SDA signal (-17...17) "
430 	  LCD 'SDA' signal has been connected. It can be :
440 	int "Parallel port pin number & polarity connected to the LCD backlight signal (-17...17) "
444 	  This describes the number of the parallel port pin to which the LCD 'BL' signal
456 	bool "Change LCD initialization message ?"
510 	tristate "Parallel port LCD/Keypad Panel support (OLD OPTION)"