Lines Matching +full:reg +full:- +full:names
1 // SPDX-License-Identifier: GPL-2.0+
5 // Based on imx6qdl-sabresd.dtsi which is:
9 #include <dt-bindings/clock/imx6qdl-clock.h>
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/input/input.h>
15 stdout-path = &uart4;
20 reg = <0x10000000 0x80000000>;
23 reg_usb_otg_vbus: regulator-usb-otg-vbus {
24 compatible = "regulator-fixed";
25 regulator-name = "usb_otg_vbus";
26 regulator-min-microvolt = <5000000>;
27 regulator-max-microvolt = <5000000>;
30 reg_usb_h1_vbus: regulator-usb-h1-vbus {
31 compatible = "regulator-fixed";
32 regulator-name = "usb_h1_vbus";
33 regulator-min-microvolt = <5000000>;
34 regulator-max-microvolt = <5000000>;
38 compatible = "gpio-leds";
39 pinctrl-names = "default";
40 pinctrl-0 = <&pinctrl_gpio_leds>;
42 led-0 {
44 default-state = "on";
45 linux,default-trigger = "heartbeat";
51 bus-width = <8>;
52 data-shift = <12>; /* Lines 19:12 used */
53 hsync-active = <1>;
54 vsync-active = <1>;
58 remote-endpoint = <&ov2659_to_ipu1_csi0_mux>;
62 pinctrl-names = "default";
63 pinctrl-0 = <&pinctrl_ipu1_csi0>;
68 cs-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
69 pinctrl-names = "default";
70 pinctrl-0 = <&pinctrl_ecspi1>, <&pinctrl_ecspi1_gpio>;
74 #address-cells = <1>;
75 #size-cells = <1>;
76 compatible = "st,m25p80", "jedec,spi-nor";
77 spi-max-frequency = <20000000>;
78 reg = <0>;
83 pinctrl-names = "default";
84 pinctrl-0 = <&pinctrl_enet>;
85 phy-mode = "rgmii-id";
86 phy-handle = <&phy>;
87 fsl,magic-packet;
91 #address-cells = <1>;
92 #size-cells = <0>;
94 phy: ethernet-phy@1 {
95 reg = <1>;
96 qca,clk-out-frequency = <125000000>;
97 reset-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
98 reset-assert-us = <10000>;
104 pinctrl-names = "default";
105 pinctrl-0 = <&pinctrl_hdmi_cec>;
106 ddc-i2c-bus = <&i2c3>;
111 clock-frequency = <100000>;
112 pinctrl-names = "default";
113 pinctrl-0 = <&pinctrl_i2c2>;
118 reg = <0x08>;
122 regulator-min-microvolt = <300000>;
123 regulator-max-microvolt = <1875000>;
124 regulator-boot-on;
125 regulator-always-on;
126 regulator-ramp-delay = <6250>;
130 regulator-min-microvolt = <300000>;
131 regulator-max-microvolt = <1875000>;
132 regulator-boot-on;
133 regulator-always-on;
134 regulator-ramp-delay = <6250>;
138 regulator-min-microvolt = <800000>;
139 regulator-max-microvolt = <3300000>;
140 regulator-boot-on;
141 regulator-always-on;
142 regulator-ramp-delay = <6250>;
146 regulator-min-microvolt = <400000>;
147 regulator-max-microvolt = <1975000>;
148 regulator-boot-on;
149 regulator-always-on;
153 regulator-min-microvolt = <400000>;
154 regulator-max-microvolt = <1975000>;
155 regulator-boot-on;
156 regulator-always-on;
160 regulator-min-microvolt = <800000>;
161 regulator-max-microvolt = <3300000>;
162 regulator-always-on;
166 regulator-min-microvolt = <5000000>;
167 regulator-max-microvolt = <5150000>;
171 regulator-min-microvolt = <1000000>;
172 regulator-max-microvolt = <3000000>;
173 regulator-boot-on;
174 regulator-always-on;
178 regulator-boot-on;
179 regulator-always-on;
183 regulator-min-microvolt = <800000>;
184 regulator-max-microvolt = <1550000>;
188 regulator-min-microvolt = <800000>;
189 regulator-max-microvolt = <1550000>;
193 regulator-min-microvolt = <1800000>;
194 regulator-max-microvolt = <3300000>;
198 regulator-min-microvolt = <1800000>;
199 regulator-max-microvolt = <3300000>;
200 regulator-always-on;
204 regulator-min-microvolt = <1800000>;
205 regulator-max-microvolt = <3300000>;
206 regulator-always-on;
210 regulator-min-microvolt = <1800000>;
211 regulator-max-microvolt = <3300000>;
212 regulator-always-on;
219 clock-frequency = <100000>;
220 pinctrl-names = "default";
221 pinctrl-0 = <&pinctrl_i2c3>;
226 pinctrl-names = "default";
227 pinctrl-0 = <&pinctrl_ov2659>;
229 clock-names = "xvclk";
230 reg = <0x30>;
231 powerdown-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
232 reset-gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
237 remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
238 link-frequencies = /bits/ 64 <70000000>;
239 bus-width = <8>;
240 hsync-active = <1>;
241 vsync-active = <1>;
405 pinctrl-names = "default";
406 pinctrl-0 = <&pinctrl_uart4>;
411 vbus-supply = <®_usb_h1_vbus>;
416 vbus-supply = <®_usb_otg_vbus>;
417 pinctrl-names = "default";
418 pinctrl-0 = <&pinctrl_usbotg>;
419 disable-over-current;
424 pinctrl-names = "default";
425 pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>;
426 bus-width = <4>;
427 cd-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
432 pinctrl-names = "default";
433 pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
434 bus-width = <4>;
435 cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
436 wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
441 pinctrl-names = "default";
442 pinctrl-0 = <&pinctrl_usdhc3>;
443 bus-width = <8>;
444 non-removable;
445 no-1-8-v;
454 pinctrl-names = "default";
455 pinctrl-0 = <&pinctrl_wdog>;
456 fsl,ext-reset-output;