linux/usb/pd_vdo.h

26  * <12:11>  :: reserved
73 #define VDO_CMD_CURRENT		VDO_CMD_VENDOR(11)
119  * <20:16>  :: Reserved, Shall be set to zero
184  * <23:22> :: Connector type (10b == receptacle, 11b == captive plug)
185  * <21:11> :: Reserved
247  * <23:22> :: Connector type (10b == receptacle, 11b == captive plug)
269  * <23:20> :: Reserved, Shall be set to zero
270  * <19:18> :: type-C to Type-A/B/C/Captive (00b == A, 01 == B, 10 == C, 11 == Captive)
271  * <17>    :: Reserved, Shall be set to zero
273  * <12:11> :: cable termination type (11b == both ends active VCONN req)
288  * <20>    :: Reserved, Shall be set to zero
289  * <19:18> :: Type-C to Type-C/Captive (10b == C, 11b == Captive)
290  * <17>    :: Reserved, Shall be set to zero
292  * <12:11> :: cable termination type (10b == Vconn not req, 01b == Vconn req)
293  * <10:9>  :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
294  * <8:7>   :: Reserved, Shall be set to zero
296  * <4:3>   :: Reserved, Shall be set to zero
304  * <20>    :: Reserved, Shall be set to zero
305  * <19:18> :: Connector type (10b == C, 11b == Captive)
306  * <17>    :: Reserved, Shall be set to zero
308  * <12:11> :: cable termination type (10b == one end active, 11b == both ends active VCONN req)
309  * <10:9>  :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
373 	 | ((lat) & 0x7) << 13 | ((term) & 0x3) << 11 | (tx1d) << 10		\
378 	 | ((conn) & 0x3) << 18 | ((lat) & 0xf) << 13 | ((term) & 0x3) << 11	\
382 	 | ((conn) & 0x3) << 18	| ((lat) & 0xf) << 13 | ((term) & 0x3) << 11	\
394  * <15>    :: Reserved, Shall be set to zero
396  * <11>    :: U3 to U0 transition mode (0b == direct, 1b == through U3S)
405  * <1>     :: Reserved, Shall be set to zero
439 	 | (trans) << 11 | (phy) << 10 | (ele) << 9 | (u4) << 8			\
448  * <23:12> :: Reserved, Shall be set to zero
449  * <11>    :: SSTX1 Directionality support (0b == fixed, 1b == cfgable)
460 	 | (tx1d) << 11 | (tx2d) << 10 | (rx1d) << 9 | (rx2d) << 8	\
478  * <20:17> :: Reserved, Shall be set to zero
479  * <16:15> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
481  * <13>    :: Reserved, Shall be set to zero
506  * mark the end of SVIDs.  If more than 12 SVIDs are supported command SHOULD be