Lines Matching full:pause
173 phylink_set(tmp, Pause); in phylink_is_empty_linkmode()
356 * Set all possible pause, speed and duplex linkmodes in @linkmodes that are
443 /* The MAC must support asymmetric pause towards the local in phylink_get_capabilities()
444 * device for this. We could allow just symmetric pause, but in phylink_get_capabilities()
446 * doesn't support pause. This is because there's no way to in phylink_get_capabilities()
447 * accept pause frames without transmitting them if we only in phylink_get_capabilities()
448 * support symmetric pause. in phylink_get_capabilities()
666 /* We treat the "pause" and "asym-pause" terminology as in phylink_parse_fixedlink()
669 if (fwnode_property_read_bool(fixed_node, "pause")) in phylink_parse_fixedlink()
672 if (fwnode_property_read_bool(fixed_node, "asym-pause")) in phylink_parse_fixedlink()
787 phylink_set(pl->supported, Pause); in phylink_parse_mode()
836 /* If autoneg is disabled, pause AN is also disabled */ in phylink_apply_manual_flow()
839 state->pause &= ~MLO_PAUSE_AN; in phylink_apply_manual_flow()
841 /* Manual configuration of pause modes */ in phylink_apply_manual_flow()
842 if (!(pl->link_config.pause & MLO_PAUSE_AN)) in phylink_apply_manual_flow()
843 state->pause = pl->link_config.pause; in phylink_apply_manual_flow()
855 state->pause |= MLO_PAUSE_TX; in phylink_resolve_an_pause()
857 state->pause |= MLO_PAUSE_RX; in phylink_resolve_an_pause()
993 "%s: mode=%s/%s/%s adv=%*pb pause=%02x\n", in phylink_mac_config()
998 st.pause); in phylink_mac_config()
1290 !!(pl->link_config.pause & MLO_PAUSE_AN)); in phylink_major_config()
1344 phylink_dbg(pl, "%s: mode=%s/%s adv=%*pb pause=%02x\n", __func__, in phylink_change_inband_advert()
1348 pl->link_config.pause); in phylink_change_inband_advert()
1359 !!(pl->link_config.pause & MLO_PAUSE_AN)); in phylink_change_inband_advert()
1386 state->pause = MLO_PAUSE_NONE; in phylink_mac_pcs_get_state()
1390 state->pause = pl->link_config.pause; in phylink_mac_pcs_get_state()
1412 state->pause = MLO_PAUSE_NONE; in phylink_get_fixed_state()
1432 link_state.pause = MLO_PAUSE_NONE; in phylink_mac_initial_config()
1445 static const char *phylink_pause_to_str(int pause) in phylink_pause_to_str() argument
1447 switch (pause & MLO_PAUSE_TXRX_MASK) { in phylink_pause_to_str()
1508 rx_pause = !!(link_state.pause & MLO_PAUSE_RX); in phylink_link_up()
1514 * pause frames to the MAC to limit its transmission speed. in phylink_link_up()
1538 !!(link_state.pause & MLO_PAUSE_TX), rx_pause); in phylink_link_up()
1550 phylink_pause_to_str(link_state.pause)); in phylink_link_up()
1641 link_state.pause = pl->phy_state.pause; in phylink_resolve()
1847 pl->link_config.pause = MLO_PAUSE_AN; in phylink_create()
1935 pl->phy_state.pause = MLO_PAUSE_NONE; in phylink_phy_change()
1937 pl->phy_state.pause |= MLO_PAUSE_TX; in phylink_phy_change()
1939 pl->phy_state.pause |= MLO_PAUSE_RX; in phylink_phy_change()
1958 phylink_pause_to_str(pl->phy_state.pause), in phylink_phy_change()
2046 * phy drivers should not set SUPPORTED_[Asym_]Pause") except in phylink_bringup_phy()
2080 pl->phy_state.pause = MLO_PAUSE_NONE; in phylink_bringup_phy()
2758 * represent the supported speeds/duplex/pause modes. in phylink_ethtool_ksettings_get()
2834 * - other configuration changes (e.g. pause modes) are in phylink_ethtool_ksettings_set()
2838 * link_config.{speed,duplex,an_enabled,pause} are not used. in phylink_ethtool_ksettings_set()
2840 * pause modes when in 1000base-X mode with a PHY, but in in phylink_ethtool_ksettings_set()
2995 * phylink_ethtool_get_pauseparam() - get the current pause parameters
2997 * @pause: a pointer to a &struct ethtool_pauseparam
3000 struct ethtool_pauseparam *pause) in phylink_ethtool_get_pauseparam() argument
3004 pause->autoneg = !!(pl->link_config.pause & MLO_PAUSE_AN); in phylink_ethtool_get_pauseparam()
3005 pause->rx_pause = !!(pl->link_config.pause & MLO_PAUSE_RX); in phylink_ethtool_get_pauseparam()
3006 pause->tx_pause = !!(pl->link_config.pause & MLO_PAUSE_TX); in phylink_ethtool_get_pauseparam()
3011 * phylink_ethtool_set_pauseparam() - set the current pause parameters
3013 * @pause: a pointer to a &struct ethtool_pauseparam
3016 struct ethtool_pauseparam *pause) in phylink_ethtool_set_pauseparam() argument
3027 if (!phylink_test(pl->supported, Pause) && in phylink_ethtool_set_pauseparam()
3032 pause->rx_pause != pause->tx_pause) in phylink_ethtool_set_pauseparam()
3036 if (pause->autoneg) in phylink_ethtool_set_pauseparam()
3038 if (pause->rx_pause) in phylink_ethtool_set_pauseparam()
3040 if (pause->tx_pause) in phylink_ethtool_set_pauseparam()
3049 * rx tx Pause AsymDir in phylink_ethtool_set_pauseparam()
3055 * rx/tx pause resolution. in phylink_ethtool_set_pauseparam()
3057 linkmode_set_pause(config->advertising, pause->tx_pause, in phylink_ethtool_set_pauseparam()
3058 pause->rx_pause); in phylink_ethtool_set_pauseparam()
3060 manual_changed = (config->pause ^ pause_state) & MLO_PAUSE_AN || in phylink_ethtool_set_pauseparam()
3062 (config->pause ^ pause_state) & MLO_PAUSE_TXRX_MASK); in phylink_ethtool_set_pauseparam()
3064 config->pause = pause_state; in phylink_ethtool_set_pauseparam()
3074 /* If we have a PHY, a change of the pause frame advertisement will in phylink_ethtool_set_pauseparam()
3080 phy_set_asym_pause(pl->phydev, pause->rx_pause, in phylink_ethtool_set_pauseparam()
3081 pause->tx_pause); in phylink_ethtool_set_pauseparam()
3083 /* If the manual pause settings changed, make sure we trigger a in phylink_ethtool_set_pauseparam()
3195 fs.pause = test_bit(ETHTOOL_LINK_MODE_Pause_BIT, lpa); in phylink_mii_emul_read()
3540 config.pause = MLO_PAUSE_AN; in phylink_sfp_config_phy()
3605 config.pause = MLO_PAUSE_AN; in phylink_sfp_config_optical()
3731 * phy drivers should not set SUPPORTED_[Asym_]Pause") except in phylink_sfp_connect_phy()
3966 state->pause |= MLO_PAUSE_TX | MLO_PAUSE_RX; in phylink_mii_c22_pcs_decode_state()
3976 state->pause |= MLO_PAUSE_TX | MLO_PAUSE_RX; in phylink_mii_c22_pcs_decode_state()