dts/renesas/r8a7790-stout.dts

1 // SPDX-License-Identifier: GPL-2.0
8 /dts-v1/;
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/input/input.h>
23 		stdout-path = "serial0:115200n8";
32 		compatible = "gpio-leds";
47 	fixedregulator1v8: regulator-1v8 {
48 		compatible = "regulator-fixed";
49 		regulator-name = "fixed-1.8V";
50 		regulator-min-microvolt = <1800000>;
51 		regulator-max-microvolt = <1800000>;
52 		regulator-boot-on;
53 		regulator-always-on;
56 	fixedregulator3v3: regulator-3v3 {
57 		compatible = "regulator-fixed";
58 		regulator-name = "fixed-3.3V";
59 		regulator-min-microvolt = <3300000>;
60 		regulator-max-microvolt = <3300000>;
61 		regulator-boot-on;
62 		regulator-always-on;
65 	vcc_sdhi0: regulator-vcc-sdhi0 {
66 		compatible = "regulator-fixed";
68 		regulator-name = "SDHI0 Vcc";
69 		regulator-min-microvolt = <3300000>;
70 		regulator-max-microvolt = <3300000>;
73 		enable-active-high;
76 	hdmi-out {
77 		compatible = "hdmi-connector";
82 				remote-endpoint = <&adv7511_out>;
87 	osc1_clk: osc1-clock {
88 		compatible = "fixed-clock";
89 		#clock-cells = <0>;
90 		clock-frequency = <148500000>;
93 	osc4_clk: osc4-clock {
94 		compatible = "fixed-clock";
95 		#clock-cells = <0>;
96 		clock-frequency = <12000000>;
101 	pinctrl-0 = <&du_pins>;
102 	pinctrl-names = "default";
107 	clock-names = "du.0", "du.1", "du.2", "dclkin.0";
112 				remote-endpoint = <&adv7511_in>;
137 	clock-frequency = <20000000>;
142 	pinctrl-0 = <&scif_clk_pins>;
143 	pinctrl-names = "default";
160 	ether_pins: ether {
173 		power-source = <3300>;
202 &ether {
203 	pinctrl-0 = <&ether_pins>, <&phy1_pins>;
204 	pinctrl-names = "default";
206 	phy-handle = <&phy1>;
207 	renesas,ether-link-active-low;
210 	phy1: ethernet-phy@1 {
211 		compatible = "ethernet-phy-id0022.1537",
212 			     "ethernet-phy-ieee802.3-c22";
214 		interrupts-extended = <&irqc0 1 IRQ_TYPE_LEVEL_LOW>;
215 		micrel,led-mode = <1>;
216 		reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
225 	pinctrl-0 = <&qspi_pins>;
226 	pinctrl-names = "default";
231 		compatible = "spansion,s25fl512s", "jedec,spi-nor";
233 		spi-max-frequency = <30000000>;
234 		spi-tx-bus-width = <4>;
235 		spi-rx-bus-width = <4>;
236 		spi-cpha;
237 		spi-cpol;
238 		m25p,fast-read;
241 			compatible = "fixed-partitions";
242 			#address-cells = <1>;
243 			#size-cells = <1>;
248 				read-only;
253 				read-only;
256 				label = "uboot-env";
258 				read-only;
269 	pinctrl-0 = <&scifa0_pins>;
270 	pinctrl-names = "default";
271 	bootph-all;
277 	clock-frequency = <14745600>;
281 	pinctrl-0 = <&sdhi0_pins>;
282 	pinctrl-names = "default";
284 	vmmc-supply = <&vcc_sdhi0>;
285 	cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
290 	cpu0-supply = <&vdd_dvfs>;
295 	pinctrl-0 = <&iic2_pins>;
296 	pinctrl-names = "default";
298 	clock-frequency = <100000>;
303 		interrupts-extended = <&gpio1 15 IRQ_TYPE_LEVEL_LOW>;
305 		clock-names = "cec";
307 		avdd-supply = <&fixedregulator1v8>;
308 		dvdd-supply = <&fixedregulator1v8>;
309 		pvdd-supply = <&fixedregulator1v8>;
310 		dvdd-3v-supply = <&fixedregulator3v3>;
311 		bgvdd-supply = <&fixedregulator1v8>;
313 		adi,input-depth = <8>;
314 		adi,input-colorspace = "rgb";
315 		adi,input-clock = "1x";
318 			#address-cells = <1>;
319 			#size-cells = <0>;
324 					remote-endpoint = <&du_out_rgb>;
331 					remote-endpoint = <&hdmi_con_out>;
339 	pinctrl-names = "default";
340 	pinctrl-0 = <&iic3_pins>, <&pmic_irq_pins>;
346 		interrupts-extended = <&irqc0 2 IRQ_TYPE_LEVEL_LOW>;
347 		interrupt-controller;
348 		#interrupt-cells = <2>;
351 			compatible = "dlg,da9063-onkey";
355 			compatible = "dlg,da9063-rtc";
359 			compatible = "dlg,da9063-watchdog";
366 		interrupts-extended = <&irqc0 2 IRQ_TYPE_LEVEL_LOW>;
368 		regulator-min-microvolt = <1000000>;
369 		regulator-max-microvolt = <1000000>;
370 		regulator-boot-on;
371 		regulator-always-on;
377 		interrupts-extended = <&irqc0 2 IRQ_TYPE_LEVEL_LOW>;
379 		regulator-min-microvolt = <1000000>;
380 		regulator-max-microvolt = <1000000>;
381 		regulator-boot-on;
382 		regulator-always-on;
388 	pinctrl-0 = <&usb0_pins>;
389 	pinctrl-names = "default";