Lines Matching +full:panic +full:- +full:indicator
1 // SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
3 * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
9 #include "stm32mp15xx-dhcor-io1v8.dtsi"
22 cec_clock: clk-cec-fixed {
23 #clock-cells = <0>;
24 compatible = "fixed-clock";
25 clock-frequency = <24000000>;
29 stdout-path = "serial0:115200n8";
32 hdmi-out {
33 compatible = "hdmi-connector";
38 remote-endpoint = <&adv7513_out>;
44 compatible = "gpio-leds";
48 linux,default-trigger = "heartbeat";
49 default-state = "off";
55 linux,default-trigger = "mmc0";
56 default-state = "off";
62 linux,default-trigger = "mmc1";
63 default-state = "off";
69 linux,default-trigger = "none";
70 default-state = "off";
71 panic-indicator;
75 sd_switch: regulator-sd_switch {
76 compatible = "regulator-gpio";
77 regulator-name = "sd_switch";
78 regulator-min-microvolt = <1800000>;
79 regulator-max-microvolt = <2900000>;
80 regulator-type = "voltage";
81 regulator-always-on;
84 gpios-states = <0>;
90 compatible = "audio-graph-card";
91 label = "STM32MP1-AV96-HDMI";
96 wlan_pwr: regulator-wlan {
97 compatible = "regulator-fixed";
99 regulator-name = "wl-reg";
100 regulator-min-microvolt = <3300000>;
101 regulator-max-microvolt = <3300000>;
104 enable-active-high;
109 pinctrl-names = "default";
110 pinctrl-0 = <&adc12_ain_pins_b>;
111 vdd-supply = <&vdd>;
112 vdda-supply = <&vdda>;
113 vref-supply = <&vdda>;
117 st,adc-channels = <0 1 6>;
118 st,min-sample-time-nsecs = <5000>;
123 st,adc-channels = <0 1 2>;
124 st,min-sample-time-nsecs = <5000>;
131 pinctrl-0 = <ðernet0_rgmii_pins_c>;
132 pinctrl-1 = <ðernet0_rgmii_sleep_pins_c>;
133 pinctrl-names = "default", "sleep";
134 phy-mode = "rgmii";
135 max-speed = <1000>;
136 phy-handle = <&phy0>;
139 #address-cells = <1>;
140 #size-cells = <0>;
141 compatible = "snps,dwmac-mdio";
142 reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
143 reset-delay-us = <1000>;
145 phy0: ethernet-phy@7 {
148 rxc-skew-ps = <1500>;
149 rxdv-skew-ps = <540>;
150 rxd0-skew-ps = <420>;
151 rxd1-skew-ps = <420>;
152 rxd2-skew-ps = <420>;
153 rxd3-skew-ps = <420>;
155 txc-skew-ps = <1440>;
156 txen-skew-ps = <540>;
157 txd0-skew-ps = <420>;
158 txd1-skew-ps = <420>;
159 txd2-skew-ps = <420>;
160 txd3-skew-ps = <420>;
166 pinctrl-names = "default";
167 pinctrl-0 = <&i2c1_pins_b>;
168 i2c-scl-rising-time-ns = <185>;
169 i2c-scl-falling-time-ns = <20>;
171 /delete-property/dmas;
172 /delete-property/dma-names;
176 pinctrl-names = "default";
177 pinctrl-0 = <&i2c2_pins_c>;
178 i2c-scl-rising-time-ns = <185>;
179 i2c-scl-falling-time-ns = <20>;
181 /delete-property/dmas;
182 /delete-property/dma-names;
186 hdmi-transmitter@3d {
189 reg-names = "main", "cec", "edid", "packet";
191 clock-names = "cec";
193 avdd-supply = <&v3v3>;
194 dvdd-supply = <&v3v3>;
195 pvdd-supply = <&v3v3>;
196 dvdd-3v-supply = <&v3v3>;
197 bgvdd-supply = <&v3v3>;
200 interrupt-parent = <&gpiog>;
204 adi,input-depth = <8>;
205 adi,input-colorspace = "rgb";
206 adi,input-clock = "1x";
207 adi,input-style = <1>;
208 adi,input-justification = "evenly";
211 #address-cells = <1>;
212 #size-cells = <0>;
217 remote-endpoint = <<dc_ep0_out>;
224 remote-endpoint = <&hdmi_con>;
231 remote-endpoint = <&sai2a_endpoint>;
239 pinctrl-names = "default", "sleep";
240 pinctrl-0 = <<dc_pins_d>;
241 pinctrl-1 = <<dc_sleep_pins_d>;
245 #address-cells = <1>;
246 #size-cells = <0>;
250 remote-endpoint = <&adv7513_in>;
257 pinctrl-names = "default", "sleep";
258 pinctrl-0 = <&sai2a_pins_c>;
259 pinctrl-1 = <&sai2a_sleep_pins_c>;
260 clock-names = "pclk", "x8k", "x11k";
263 sai2a: audio-controller@4400b004 {
264 #clock-cells = <0>;
265 dma-names = "tx";
267 clock-names = "sai_ck";
272 remote-endpoint = <&adv7513_i2s0>;
274 mclk-fs = <256>;
281 pinctrl-names = "default", "opendrain", "sleep";
282 pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
283 pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
284 pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
285 cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
286 disable-wp;
287 st,sig-dir;
288 st,neg-edge;
289 st,use-ckin;
290 bus-width = <4>;
291 vmmc-supply = <&vdd_sd>;
292 vqmmc-supply = <&sd_switch>;
297 pinctrl-names = "default", "opendrain", "sleep";
298 pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
299 pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_c>;
300 pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_c>;
301 bus-width = <8>;
302 mmc-ddr-1_8v;
303 no-sd;
304 no-sdio;
305 non-removable;
306 st,neg-edge;
307 vmmc-supply = <&v3v3>;
308 vqmmc-supply = <&vdd_io>;
313 pinctrl-names = "default", "opendrain", "sleep";
314 pinctrl-0 = <&sdmmc3_b4_pins_b>;
315 pinctrl-1 = <&sdmmc3_b4_od_pins_b>;
316 pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>;
317 broken-cd;
318 non-removable;
319 st,neg-edge;
320 bus-width = <4>;
321 vmmc-supply = <&wlan_pwr>;
324 #address-cells = <1>;
325 #size-cells = <0>;
328 compatible = "brcm,bcm4329-fmac";
333 pinctrl-names = "default";
334 pinctrl-0 = <&spi2_pins_a>;
335 cs-gpios = <&gpioi 0 0>;
337 /delete-property/dmas;
338 /delete-property/dma-names;
343 label = "LS-UART1";
344 pinctrl-names = "default";
345 pinctrl-0 = <&uart4_pins_b>;
351 label = "LS-UART0";
352 pinctrl-names = "default";
353 pinctrl-0 = <&uart7_pins_a>;
354 uart-has-rtscts;
360 pinctrl-names = "default", "sleep";
361 pinctrl-0 = <&usart2_pins_a>;
362 pinctrl-1 = <&usart2_sleep_pins_a>;
363 st,hw-flow-ctrl;
367 compatible = "brcm,bcm43438-bt";
368 max-speed = <3000000>;
369 shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
375 phy-names = "usb";
380 pinctrl-0 = <&usbotg_hs_pins_a>;
381 pinctrl-names = "default";
382 phy-names = "usb2-phy";
385 vbus-supply = <&vbus_otg>;
393 phy-supply = <&vdd_usb>;
394 vdda1v1-supply = <®11>;
395 vdda1v8-supply = <®18>;
399 phy-supply = <&vdd_usb>;
400 vdda1v1-supply = <®11>;
401 vdda1v8-supply = <®18>;