Lines Matching +full:imx27 +full:- +full:clock
1 // SPDX-License-Identifier: GPL-2.0-or-later
6 /dts-v1/;
7 #include "imx27.dtsi"
11 compatible = "phytec,imx27-pcm038", "fsl,imx27";
19 compatible = "simple-bus";
20 #address-cells = <1>;
21 #size-cells = <0>;
24 compatible = "regulator-fixed";
26 regulator-name = "3V3";
27 regulator-min-microvolt = <3300000>;
28 regulator-max-microvolt = <3300000>;
32 compatible = "regulator-fixed";
34 regulator-name = "5V0";
35 regulator-min-microvolt = <5000000>;
36 regulator-max-microvolt = <5000000>;
41 compatible = "simple-bus";
42 #address-cells = <1>;
43 #size-cells = <0>;
46 compatible = "usb-nop-xceiv";
48 vcc-supply = <&sw3_reg>;
50 clock-names = "main_clk";
51 #phy-cells = <0>;
61 fsl,audmux-port = <0>;
62 fsl,port-config = <0xcb205000>;
66 fsl,audmux-port = <2>;
67 fsl,port-config = <0x00001000>;
72 pinctrl-names = "default";
73 pinctrl-0 = <&pinctrl_cspi1>;
74 cs-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
79 pinctrl-names = "default";
80 pinctrl-0 = <&pinctrl_pmic>;
82 spi-cs-high;
83 spi-max-frequency = <20000000>;
84 interrupt-parent = <&gpio2>;
86 fsl,mc13xxx-uses-adc;
87 fsl,mc13xxx-uses-rtc;
90 #address-cells = <1>;
91 #size-cells = <0>;
92 led-control = <0x001 0x000 0x000 0x000 0x000 0x000>;
98 regulator-min-microvolt = <1200000>;
99 regulator-max-microvolt = <1520000>;
100 regulator-always-on;
101 regulator-boot-on;
106 regulator-min-microvolt = <1800000>;
107 regulator-max-microvolt = <1800000>;
108 regulator-always-on;
109 regulator-boot-on;
113 regulator-min-microvolt = <5000000>;
114 regulator-max-microvolt = <5000000>;
115 regulator-always-on;
116 regulator-boot-on;
120 regulator-always-on;
121 regulator-boot-on;
125 regulator-min-microvolt = <1800000>;
126 regulator-max-microvolt = <1800000>;
127 regulator-always-on;
128 regulator-boot-on;
132 regulator-always-on;
133 regulator-boot-on;
137 regulator-min-microvolt = <1500000>;
138 regulator-max-microvolt = <1500000>;
139 regulator-always-on;
140 regulator-boot-on;
144 regulator-min-microvolt = <2800000>;
145 regulator-max-microvolt = <2800000>;
149 regulator-min-microvolt = <2775000>;
150 regulator-max-microvolt = <2775000>;
151 regulator-always-on;
152 regulator-boot-on;
156 regulator-min-microvolt = <2775000>;
157 regulator-max-microvolt = <2775000>;
158 regulator-always-on;
159 regulator-boot-on;
163 regulator-min-microvolt = <1600000>;
164 regulator-max-microvolt = <3000000>;
170 regulator-always-on;
177 phy-mode = "mii";
178 phy-reset-gpios = <&gpio3 30 GPIO_ACTIVE_LOW>;
179 phy-supply = <®_3v3>;
180 pinctrl-names = "default";
181 pinctrl-0 = <&pinctrl_fec1>;
186 clock-frequency = <400000>;
187 pinctrl-names = "default";
188 pinctrl-0 = <&pinctrl_i2c2>;
297 pinctrl-names = "default";
298 pinctrl-0 = <&pinctrl_nfc>;
299 nand-bus-width = <8>;
300 nand-ecc-mode = "hw";
301 nand-on-flash-bbt;
306 pinctrl-names = "default";
307 pinctrl-0 = <&pinctrl_ssi1>;
312 pinctrl-names = "default";
313 pinctrl-0 = <&pinctrl_usbotg>;
317 vbus-supply = <&sw3_reg>;
318 disable-over-current;
326 compatible = "cfi-flash";
328 bank-width = <2>;
329 linux,mtd-name = "physmap-flash.0";
330 fsl,weim-cs-timing = <0x22c2cf00 0x75000d01 0x00000900>;
331 #address-cells = <1>;
332 #size-cells = <1>;
336 compatible = "mtd-ram";
338 bank-width = <2>;
339 linux,mtd-name = "mtd-ram.0";
340 fsl,weim-cs-timing = <0x0000d843 0x22252521 0x22220a00>;
341 #address-cells = <1>;
342 #size-cells = <1>;