boot/dts/imx27-phytec-phycore-rdk.dts

1 // SPDX-License-Identifier: GPL-2.0-or-later
5 #include "imx27-phytec-phycore-som.dtsi"
9 	compatible = "phytec,imx27-pcm970", "phytec,imx27-pcm038", "fsl,imx27";
12 		stdout-path = &uart1;
16 		model = "Sharp-LQ035Q7";
17 		bits-per-pixel = <16>;
20 		display-timings {
21 			native-mode = <&timing0>;
23 				clock-frequency = <5500000>;
26 				hback-porch = <5>;
27 				hsync-len = <7>;
28 				hfront-porch = <16>;
29 				vback-porch = <7>;
30 				vsync-len = <1>;
31 				vfront-porch = <9>;
32 				pixelclk-active = <1>;
33 				hsync-active = <1>;
34 				vsync-active = <1>;
35 				de-active = <0>;
42 			compatible = "regulator-fixed";
43 			pinctrl-names = "default";
44 			pinctrl-0 = <&pinctrl_csien>;
46 			regulator-name = "CSI_EN";
47 			regulator-min-microvolt = <3300000>;
48 			regulator-max-microvolt = <3300000>;
50 			regulator-always-on;
56 			compatible = "usb-nop-xceiv";
58 			vcc-supply = <&reg_5v0>;
60 			clock-names = "main_clk";
61 			#phy-cells = <0>;
67 	pinctrl-0 = <&pinctrl_cspi1>, <&pinctrl_cspi1cs1>;
68 	cs-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>,
73 	pinctrl-names = "default";
74 	pinctrl-0 = <&pinctrl_imxfb1>;
76 	lcd-supply = <&reg_5v0>;
84 	clock-frequency = <400000>;
85 	pinctrl-names = "default";
86 	pinctrl-0 = <&pinctrl_i2c1>;
92 		gpio-controller;
93 		#gpio-cells = <2>;
215 	pinctrl-names = "default";
216 	pinctrl-0 = <&pinctrl_owire1>;
254 		linux,default-trigger = "nand-disk";
260 		linux,default-trigger = "heartbeat";
266 		linux,default-trigger = "cpu0";
271 	pinctrl-names = "default";
272 	pinctrl-0 = <&pinctrl_sdhc2>;
273 	bus-width = <4>;
274 	cd-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
275 	wp-gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>;
276 	vmmc-supply = <&vmmc1_reg>;
281 	uart-has-rtscts;
282 	pinctrl-names = "default";
283 	pinctrl-0 = <&pinctrl_uart1>;
288 	uart-has-rtscts;
289 	pinctrl-names = "default";
290 	pinctrl-0 = <&pinctrl_uart2>;
295 	pinctrl-names = "default";
296 	pinctrl-0 = <&pinctrl_usbh2>;
299 	vbus-supply = <&reg_5v0>;
301 	disable-over-current;
306 	pinctrl-names = "default";
307 	pinctrl-0 = <&pinctrl_weim>;
312 		interrupt-parent = <&gpio5>;
314 		nxp,external-clock-frequency = <16000000>;
315 		nxp,tx-output-config = <0x16>;
316 		nxp,no-comparator-bypass;
317 		fsl,weim-cs-timing = <0x0000dcf6 0x444a0301 0x44443302>;