Lines Matching +full:select +full:- +full:gpios
8 Select this config option from the architecture Kconfig, if
11 Select this instead of ARCH_REQUIRE_GPIOLIB, if your architecture does
12 not depend on GPIOs being available, but rather let the user
17 select GPIOLIB
19 Platforms select gpiolib if they use this infrastructure
20 for all their GPIOs, usually starting with ones integrated
30 select GENERIC_GPIO
45 These checks help ensure that GPIOs have been properly initialized
47 non-sleeping contexts. They can make bitbanged serial protocols
55 Say Y here to add a sysfs interface for GPIOs.
83 tristate "Generic memory-mapped GPIO controller support (MMIO platform device)"
84 select GPIO_GENERIC
86 Say yes here to support basic platform_device memory-mapped GPIO controllers.
97 select GPIO_GENERIC
109 MPC512x/831x/834x/837x/8572/8610 GPIOs.
130 select GPIO_GENERIC
131 select GENERIC_IRQ_CHIP
136 select GPIO_GENERIC
137 select GENERIC_IRQ_CHIP
142 select GENERIC_IRQ_CHIP
159 tristate "NEC VR4100 series General-purpose I/O Uint support"
162 Say yes here to support the NEC VR4100 series General-purpose I/O Uint
167 select MFD_CORE
168 select LPC_SCH
172 The Intel SCH contains a total of 14 GPIO pins. Ten GPIOs are
174 modes (S3 and higher). The remaining four GPIOs are powered by
175 the Intel SCH suspend power supply. These GPIOs remain
176 active during S3. The suspend powered GPIOs can be used to wake the
177 system from the Suspend-to-RAM state.
178 The Intel Tunnel Creek processor has 5 GPIOs powered by the
184 select MFD_CORE
185 select MFD_VX855
198 select GPIO_MAX730X
200 GPIO driver for Maxim MAX7301 I2C-based GPIO expander.
203 tristate "MAX7319, MAX7320-7327 I2C Port Expanders"
206 Say yes here to support the MAX7319, MAX7320-7327 series of I2C
208 Input (designated by 'I'), Push-Pull Output ('O'), or Open-Drain
219 number for these GPIOs.
232 Say yes here to provide access to several register-oriented
254 Say yes here to provide access to most "quasi-bidirectional" I2C
267 use, and assign numbers to the GPIOs they expose. Those GPIOs
269 other GPIOs, but only accessible from task contexts.
271 This driver provides an in-kernel interface to those GPIOs using
272 platform-neutral GPIO calls.
279 Say yes here to provide support for Semtech SX150-series I2C
286 bool "STMPE GPIOs"
289 This enables support for the GPIOs found on the STMPE I/O
293 bool "TC3589X GPIOs"
296 This enables support for the GPIOs found on the TC3589X
306 tristate "TWL4030, TWL5030, and TPS659x0 GPIOs"
309 Say yes here to access the GPIO signals of various multi-function
313 tristate "WM831x GPIOs"
320 tristate "WM8350 GPIOs"
327 tristate "WM8994 GPIOs"
337 This option enables support for on-chip GPIO found
344 This option enables support for 18 GPIOs found
373 This chip can be found on Miro, Hauppauge and STB TV-cards.
391 select GENERIC_IRQ_CHIP
407 select GENERIC_IRQ_CHIP
411 Hub) which is for IVI(In-Vehicle Infotainment) use.
417 ---help---
421 tristate "RDC R-321x GPIO support"
423 select MFD_CORE
424 select MFD_RDC321X
426 Support for the RDC R321x SoC GPIOs over southbridge
434 select GPIO_MAX730X
436 GPIO driver for Maxim MAX7301 SPI-based GPIO expander.
447 tristate "Freescale MC33880 high-side/low-side switch"
450 SPI driver for Freescale MC33880 high-side/low-side switch.
454 tristate "74x164 serial-in/parallel-out 8-bits shift register"
457 Platform driver for 74x164 compatible serial-in/parallel-out
458 8-outputs shift registers. This driver can be used to provide access
473 tristate "Janz VMOD-TTL Digital IO Module"
476 This enables support for the Janz VMOD-TTL Digital IO module.
481 bool "ST-Ericsson AB8500 Mixed Signal Circuit gpio functions"
484 Select this to enable the AB8500 IC GPIO driver
490 Select this option to enable GPIO driver for the TPS65910