boot/dts/tqm5200.dts

24 		#size-cells = <0>;
26 		PowerPC,5200@0 {
28 			reg = <0>;
31 			d-cache-size = <0x4000>;	// L1, 16K
32 			i-cache-size = <0x4000>;	// L1, 16K
33 			timebase-frequency = <0>;	// from bootloader
34 			bus-frequency = <0>;		// from bootloader
35 			clock-frequency = <0>;		// from bootloader
41 		reg = <0x00000000 0x04000000>;	// 64MB
48 		ranges = <0 0xf0000000 0x0000c000>;
49 		reg = <0xf0000000 0x00000100>;
50 		bus-frequency = <0>;		// from bootloader
51 		system-frequency = <0>;		// from bootloader
55 			reg = <0x200 0x38>;
63 			reg = <0x500 0x80>;
68 			reg = <0x600 0x10>;
69 			interrupts = <1 9 0>;
75 			interrupts = <2 17 0>;
76 			reg = <0x900 0x80>;
81 			interrupts = <2 18 0>;
82 			reg = <0x980 0x80>;
87 			reg = <0xb00 0x40>;
88 			interrupts = <1 7 0>;
95 			reg = <0x1000 0xff>;
96 			interrupts = <2 6 0>;
101 			reg = <0x1200 0x80>;
102 			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
103 			              3 4 0  3 5 0  3 6 0  3 7 0
104 			              3 8 0  3 9 0  3 10 0  3 11 0
105 			              3 12 0  3 13 0  3 14 0  3 15 0>;
110 			reg = <0x1f00 0x100>;
115 			reg = <0x2000 0x100>;
116 			interrupts = <2 1 0>;
121 			reg = <0x2200 0x100>;
122 			interrupts = <2 2 0>;
127 			reg = <0x2400 0x100>;
128 			interrupts = <2 3 0>;
133 			reg = <0x3000 0x400>;
135 			interrupts = <2 5 0>;
141 			#size-cells = <0>;
143 			reg = <0x3000 0x400>;       // fec range, since we need to setup fec interrupts
144 			interrupts = <2 5 0>;   // these are for "mii command finished", not link changes & co.
146 			phy0: ethernet-phy@0 {
147 				reg = <0>;
153 			reg = <0x3a00 0x100>;
154 			interrupts = <2 7 0>;
159 			#size-cells = <0>;
161 			reg = <0x3d40 0x40>;
162 			interrupts = <2 16 0>;
166 				reg = <0x68>;
172 			reg = <0x8000 0x4000>;
180 		ranges = <0 0 0xfc000000 0x02000000>;
182 		flash@0,0 {
184 			reg = <0 0 0x02000000>;
198 		reg = <0xf0000d00 0x100>;
199 		interrupt-map-mask = <0xf800 0 0 7>;
200 		interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3
201 				 0xc000 0 0 2 &mpc5200_pic 0 0 3
202 				 0xc000 0 0 3 &mpc5200_pic 0 0 3
203 				 0xc000 0 0 4 &mpc5200_pic 0 0 3>;
204 		clock-frequency = <0>; // From boot loader
205 		interrupts = <2 8 0 2 9 0 2 10 0>;
206 		bus-range = <0 0>;
207 		ranges = <0x42000000 0 0x80000000 0x80000000 0 0x10000000
208 			  0x02000000 0 0x90000000 0x90000000 0 0x10000000
209 			  0x01000000 0 0x00000000 0xa0000000 0 0x01000000>;