Lines Matching full:command
103 command = event-type. (one of the constants ISDN_STAT_...)
110 int (*command)(isdn_ctrl*);
120 command = command to perform. (one of the constants ISDN_CMD_...)
121 arg = depends on command.
122 num = depends on command.
212 All commands will be performed by calling the function command() described
213 above from within the LL. The field command of the struct-parameter will
214 contain the desired command, the field driver is always set to the
225 This command is intended for performing ioctl-calls for configuring
232 called with the field command set to 1.
236 command = ISDN_CMD_IOCTL
246 This command is used to tell the HL-driver it should dial a given
251 command = ISDN_CMD_DIAL
268 With this command, the HL-driver is told to accept a D-Channel-setup.
273 command = ISDN_CMD_ACCEPTD
279 With this command, the HL-driver is told to perform a B-Channel-setup.
284 command = ISDN_CMD_ACCEPTB
290 With this command, the HL-driver is told to hangup (B-Channel if
291 established first, then D-Channel). This command is also used for
296 command = ISDN_CMD_HANGUP
302 With this command, the HL-driver is told not to signal incoming
307 command = ISDN_CMD_CLREAZ
313 With this command, the HL-driver is told to signal incoming calls for
318 command = ISDN_CMD_SETEAZ
328 With this command, the HL-driver is told to report the current setting
333 command = ISDN_CMD_GETEAZ
339 With this command, the HL-driver is told to signal only incoming
344 command = ISDN_CMD_SETSIL
350 With this command, the HL-driver is told to return the current
355 command = ISDN_CMD_SETSIL
361 With this command, the HL-driver is told to select the given Layer-2-
362 protocol. This command is issued by the LL prior to ISDN_CMD_DIAL or
368 command = ISDN_CMD_SETL2
376 With this command, the HL-driver is told to return the current
381 command = ISDN_CMD_GETL2
389 With this command, the HL-driver is told to select the given Layer-3-
390 protocol. This command is issued by the LL prior to ISDN_CMD_DIAL or
396 command = ISDN_CMD_SETL3
404 With this command, the HL-driver is told to return the current
409 command = ISDN_CMD_GETL3
417 With this command, the HL-driver is told to proceed with a incoming call.
421 command = ISDN_CMD_PROCEED
428 With this command, the HL-driver is told to alert a proceeding call.
432 command = ISDN_CMD_ALERT
439 With this command, the HL-driver is told to redirect a call in proceeding
444 command = ISDN_CMD_REDIR
458 command = ISDN_CMD_PROT_IO
468 With this command the HL-driver receives a fax sub-command.
473 command = ISDN_CMD_FAXCMD
481 function statcallb(). The field command of the struct isdn_cmd has
496 command = ISDN_STAT_STAVAIL
509 command = ISDN_STAT_ICALL
537 The keypad support now is included in the dial command.
547 command = ISDN_STAT_RUN
558 command = ISDN_STAT_STOP
569 command = ISDN_STAT_DCONN
584 command = ISDN_STAT_BCONN
599 command = ISDN_STAT_DHUP
614 command = ISDN_STAT_BHUP
625 command = ISDN_STAT_CINF
638 command = ISDN_STAT_UNLOAD
650 command = ISDN_STAT_BSENT
663 command = ISDN_STAT_NODCH
677 command = ISDN_STAT_ADDCH
690 command = ISDN_STAT_NODCH
701 command = ISDN_STAT_DISPLAY
712 command = ISDN_STAT_PROT
732 command = ISDN_STAT_DISCH
745 command = ISDN_STAT_L1ERR
751 With this call the HL-driver signals a fax sub-command to the LL.
756 command = ISDN_STAT_FAXIND