clk: qcom: dispcc-sm8550: fix DisplayPort clocks

On SM8550 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency

clk: qcom: dispcc-sm8550: fix DisplayPort clocks

On SM8550 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency tables and use clk_byte2_ops for those clocks.

This fixes frequency selection in the OPP core (which otherwise attempts
to use invalid 810 KHz as DP link rate), also fixing the following
message:
msm-dp-display ae90000.displayport-controller: _opp_config_clk_single: failed to set clock rate: -22

Fixes: 90114ca11476 ("clk: qcom: add SM8550 DISPCC driver")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240424-dispcc-dp-clocks-v2-3-b44038f3fa96@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

show more ...

Merge drm/drm-next into drm-xe-next

Backmerging drm-next in order to get up-to-date and in particular
to access commit 9ca5facd0400f610f3f7f71aeb7fc0b949a48c67.

Signed-off-by: Thomas Hellström <tho

Merge drm/drm-next into drm-xe-next

Backmerging drm-next in order to get up-to-date and in particular
to access commit 9ca5facd0400f610f3f7f71aeb7fc0b949a48c67.

Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>

show more ...

Merge tag 'phy_dp_modes_6.10' into msm-next-lumag

Merge DisplayPort subnode API in order to allow DisplayPort driver to
configure the PHYs either to the DP or eDP mode, depending on hardware
configu

Merge tag 'phy_dp_modes_6.10' into msm-next-lumag

Merge DisplayPort subnode API in order to allow DisplayPort driver to
configure the PHYs either to the DP or eDP mode, depending on hardware
configuration.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

show more ...

Merge tag 'asoc-fix-v6.9-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v6.9

A relatively large set of fixes here, the biggest piece of it is a

Merge tag 'asoc-fix-v6.9-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v6.9

A relatively large set of fixes here, the biggest piece of it is a
series correcting some problems with the delay reporting for Intel SOF
cards but there's a bunch of other things. Everything here is driver
specific except for a fix in the core for an issue with sign extension
handling volume controls.

show more ...

Merge drm/drm-next into drm-intel-next

Catching up on 6.9-rc2

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Merge drm/drm-next into drm-misc-next

Backmerging to get v6.9-rc2 changes into drm-misc-next.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge branch 'topic/sound-devel-6.10' into for-next

Merge drm/drm-fixes into drm-misc-fixes

Backmerging to get drm-misc-fixes to the state of v6.9-rc1.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge tag 'v6.9-rc1' into sched/core, to pick up fixes and to refresh the branch

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Cross-merge networking fixes after downstream PR.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'master' into mm-stable

Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux

Pull clk updates from Stephen Boyd:
"Not a ton of stuff happening in the clk framework. We got some more
devm

Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux

Pull clk updates from Stephen Boyd:
"Not a ton of stuff happening in the clk framework. We got some more
devm helpers and we seem to be going in the direction of "just turn
this stuff on already and leave me alone!" with the addition of a
devm_clk_bulk_get_all_enable() API. I'm hoping that we can make that
into a pmdomain that drivers attach instead, but this API should help
drivers simplify in the meantime.

Outside of the devm wrappers, we've got the usual clk driver updates
that are dominated by the major phone SoC vendors (Samsung and
Qualcomm) and the non-critical driver fixes for things like incorrect
topology descriptions and wrong registers or bit fields. More details
are below, but I'd say that it looks pretty ordinary. The only thing
that really jumps out at me is the Renesas clk driver that's ignoring
clks that are assigned to remote processors in DeviceTree. That's a
new feature that they're using to avoid marking clks as
CLK_IGNORE_UNUSED based on the configuration of the system.

Core:
- Increase dev_id len for clkdev lookups
- Add a devm_clk_bulk_get_all_enable() API to get and enable all clks
for a device
- Add a devm variant of clk_rate_exclusive_get()

New Drivers:
- Display, TCSR, GPU, and Camera clock controllers for Qualcomm's X1
Elite SoC
- Google GS101 PERIC0 and PERIC1 clock controllers
- Exynos850 PDMA clocks
- Exynos850 CPU cluster 0 and 1 (CMU_CPUCLK0/CMU_CPUCLK1) clock
controllers

Removed Drivers:
- Remove the unused Qualcomm sc7180 modem clk driver

Updates:
- Fix some static checker errors in the Hisilicon clk driver
- Polarfire MSSPLL hardware has 4 output clocks (the driver supported
previously only one output); each of these 4 outputs feed dividers
and the output of each divider feed individual hardware blocks
(e.g. CAN, Crypto, eMMC); individual hardware block drivers need to
control their clocks thus clock driver support was added for all
MSSPLL output clocks
- Typo fixes in the Qualcomm IPQ5018 GCC driver
- Add "qdss_at" clk on Qualcomm IPQ6018, needed for WiFi
- Properly terminate frequency tables in different Qualcomm clk
drivers
- Add MDSS, crypto, and SDCC resets on Qualcomm MSM8953
- Add missing UFS CLKREF clks on Qualcomm SC8180X
- Avoid significant delays during boot by adding a softdep on rpmhpd
to Qualcomm SDM845 gcc driver
- Add QUPv3 RCGS w/ DFS and video resets to Qualcomm SM8150 GCC
driver
- Fix the custom GPU GX "do-nothing" method in the Qualcomm GDSC
driver
- Add an external regulator to GX GDSC on Qualcomm SC8280XP GPU clk
driver
- Switch display, GPU, video, and camera Qualcomm clk drivers to
module_platform_driver()
- Set a longer delay for Venus resets on many Qualcomm SoCs
- Correct the GDSC wait times in the Qualcomm SDM845 display clk
driver
- Fix clock listing Oops on Amlogic axg
- New pll-rate for Rockchip rk3568
- i2s rate improvements for Rockchip rk3399
- Rockchip rk3588 syscon clock fixes and removal of overall
clock-number from the rk3588 binding header
- A prerequisite for later improvements to the Rockchip rk3588 linked
clocks
- Minor clean-ups and error handling improvements in both
composite-8m and SCU i.MX clock drivers
- Fix for SAI_MCLK_SEL definition for i.MX8MP
- Register the Samsung CMU MISC clock controller earlier, so the
Multi Core Timer clocksource can use it on Google GS101
- Propagate Exynos850 SPI IPCLK rate change to parents, so the SPI
will get proper clock rates
- Refactor the generic Samsung CPU clock controllers code, preparing
it for supporting Exynos850 CPU clocks
- Fix some clk kerneldoc warnings
- Add Ethernet, SDHI, DMA, and HyperFLASH/QSPI (RPC-IF) clocks on
Renesas R-Car V4M
- Ignore all clocks which are assigned to a non-Linux system in the
Renesas clk driver
- Add watchdog clock on Renesas RZ/G3S
- Add camera (CRU) clock and reset on Renesas RZ/G2UL
- Add support for the Renesas R-Car V4M (R8A779H0) SoC
- Convert some clk bindings to YAML so they can be validated"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
clk: zynq: Prevent null pointer dereference caused by kmalloc failure
clk: fractional-divider: Use bit operations consistently
clk: fractional-divider: Move mask calculations out of lock
clk: Fix clk_core_get NULL dereference
clk: starfive: jh7110-vout: Convert to platform remove callback returning void
clk: starfive: jh7110-isp: Convert to platform remove callback returning void
clk: imx: imx8-acm: Convert to platform remove callback returning void
clk: qcom: gcc-ipq5018: fix register offset for GCC_UBI0_AXI_ARES reset
clk: qcom: gcc-ipq5018: fix 'halt_reg' offset of 'gcc_pcie1_pipe_clk'
clk: qcom: gcc-ipq5018: fix 'enable_reg' offset of 'gcc_gmac0_sys_clk'
clk: qcom: camcc-x1e80100: Fix missing DT_IFACE enum in x1e80100 camcc
clk: qcom: mmcc-msm8974: fix terminating of frequency table arrays
clk: qcom: mmcc-apq8084: fix terminating of frequency table arrays
clk: qcom: camcc-sc8280xp: fix terminating of frequency table arrays
clk: qcom: gcc-ipq9574: fix terminating of frequency table arrays
clk: qcom: gcc-ipq8074: fix terminating of frequency table arrays
clk: qcom: gcc-ipq6018: fix terminating of frequency table arrays
clk: qcom: gcc-ipq5018: fix terminating of frequency table arrays
clk: mediatek: clk-mt8173-apmixedsys: Use common error handling code in clk_mt8173_apmixed_probe()
clk: Add a devm variant of clk_rate_exclusive_get()
...

show more ...

Merge branches 'clk-remove', 'clk-amlogic', 'clk-qcom', 'clk-parent' and 'clk-microchip' into clk-next

* clk-remove:
clk: starfive: jh7110-vout: Convert to platform remove callback returning void

Merge branches 'clk-remove', 'clk-amlogic', 'clk-qcom', 'clk-parent' and 'clk-microchip' into clk-next

* clk-remove:
clk: starfive: jh7110-vout: Convert to platform remove callback returning void
clk: starfive: jh7110-isp: Convert to platform remove callback returning void
clk: imx: imx8-acm: Convert to platform remove callback returning void

* clk-amlogic:
clk: meson: Add missing clocks to axg_clk_regmaps

* clk-qcom: (62 commits)
clk: qcom: gcc-ipq5018: fix register offset for GCC_UBI0_AXI_ARES reset
clk: qcom: gcc-ipq5018: fix 'halt_reg' offset of 'gcc_pcie1_pipe_clk'
clk: qcom: gcc-ipq5018: fix 'enable_reg' offset of 'gcc_gmac0_sys_clk'
clk: qcom: camcc-x1e80100: Fix missing DT_IFACE enum in x1e80100 camcc
clk: qcom: mmcc-msm8974: fix terminating of frequency table arrays
clk: qcom: mmcc-apq8084: fix terminating of frequency table arrays
clk: qcom: camcc-sc8280xp: fix terminating of frequency table arrays
clk: qcom: gcc-ipq9574: fix terminating of frequency table arrays
clk: qcom: gcc-ipq8074: fix terminating of frequency table arrays
clk: qcom: gcc-ipq6018: fix terminating of frequency table arrays
clk: qcom: gcc-ipq5018: fix terminating of frequency table arrays
clk: qcom: dispcc-sdm845: Adjust internal GDSC wait times
dt-bindings: clk: qcom: drop the SC7180 Modem subsystem clock controller
clk: qcom: drop the SC7180 Modem subsystem clock driver
clk: qcom: Use qcom_branch_set_clk_en()
clk: qcom: branch: Add a helper for setting the enable bit
clk: qcom: dispcc-sm8250: Make clk_init_data and pll_vco const
clk: qcom: gcc-sc8180x: Add missing UFS QREF clocks
clk: qcom: gcc-msm8953: add more resets
clk: qcom: videocc-*: switch to module_platform_driver
...

* clk-parent:
clk: Fix clk_core_get NULL dereference

* clk-microchip:
clk: microchip: mpfs: convert MSSPLL outputs to clk_divider
clk: microchip: mpfs: add missing MSSPLL outputs
clk: microchip: mpfs: setup for using other mss pll outputs
clk: microchip: mpfs: split MSSPLL in two
dt-bindings: can: mpfs: add missing required clock
dt-bindings: clock: mpfs: add more MSSPLL output definitions

show more ...

Merge tag 'qcom-clk-for-6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into clk-qcom

Pull Qualcomm clk driver updates from Bjorn Andersson:

- Support for Display, TCSR, GPU, an

Merge tag 'qcom-clk-for-6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into clk-qcom

Pull Qualcomm clk driver updates from Bjorn Andersson:

- Support for Display, TCSR, GPU, and Camera clock controllers for
Qualcomm's X1 Elite SoC
- Typo fixes in the IPQ5018 GCC driver
- Add "qdss_at" clk on Qualcomm IPQ6018, needed for WiFi
- Properly terminate frequency tables in different qcom clk drivers
- Add MDSS, crypto, and SDCC resets on Qualcomm MSM8953
- Add missing UFS CLKREF clks on Qualcomm SC8180X
- Avoid significant delays during boot by adding a softdep on rpmhpd to SDM845 gcc driver
- Add QUPv3 RCGS w/ DFS and video resets to Qualcomm SM8150 GCC driver
- Fix the custom GPU GX "do-nothing" method in the GDSC driver
- Add an external regulator to GX GDSC on SC8280XP GPU clk driver
- Switch display, GPU, video, and camera clock drivers to module_platform_driver()
- Set a longer delay for Venus resets on many Qualcomm SoCs
- Correct the GDSC wait times in the Qualcomm SDM845 display clk driver
- Remove the unused Qualcomm sc7180 modem clk driver

* tag 'qcom-clk-for-6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (62 commits)
clk: qcom: gcc-ipq5018: fix register offset for GCC_UBI0_AXI_ARES reset
clk: qcom: gcc-ipq5018: fix 'halt_reg' offset of 'gcc_pcie1_pipe_clk'
clk: qcom: gcc-ipq5018: fix 'enable_reg' offset of 'gcc_gmac0_sys_clk'
clk: qcom: camcc-x1e80100: Fix missing DT_IFACE enum in x1e80100 camcc
clk: qcom: mmcc-msm8974: fix terminating of frequency table arrays
clk: qcom: mmcc-apq8084: fix terminating of frequency table arrays
clk: qcom: camcc-sc8280xp: fix terminating of frequency table arrays
clk: qcom: gcc-ipq9574: fix terminating of frequency table arrays
clk: qcom: gcc-ipq8074: fix terminating of frequency table arrays
clk: qcom: gcc-ipq6018: fix terminating of frequency table arrays
clk: qcom: gcc-ipq5018: fix terminating of frequency table arrays
clk: qcom: dispcc-sdm845: Adjust internal GDSC wait times
dt-bindings: clk: qcom: drop the SC7180 Modem subsystem clock controller
clk: qcom: drop the SC7180 Modem subsystem clock driver
clk: qcom: Use qcom_branch_set_clk_en()
clk: qcom: branch: Add a helper for setting the enable bit
clk: qcom: dispcc-sm8250: Make clk_init_data and pll_vco const
clk: qcom: gcc-sc8180x: Add missing UFS QREF clocks
clk: qcom: gcc-msm8953: add more resets
clk: qcom: videocc-*: switch to module_platform_driver
...

show more ...

Merge drm/drm-next into drm-intel-next

Sync to get the drm_printer changes to drm-intel-next.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>

clk: qcom: Use qcom_branch_set_clk_en()

Instead of magically poking at the bit0 of branch clocks' CBCR, use
the newly introduced helper.

Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
R

clk: qcom: Use qcom_branch_set_clk_en()

Instead of magically poking at the bit0 of branch clocks' CBCR, use
the newly introduced helper.

Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240212-topic-clk_branch_en-v7-2-5b79eb7278b2@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

show more ...

Merge tag 'v6.8-rc4' into x86/percpu, to resolve conflicts and refresh the branch

Conflicts:
arch/x86/include/asm/percpu.h
arch/x86/include/asm/text-patching.h

Signed-off-by: Ingo Molnar <mingo@k

Merge tag 'v6.8-rc4' into x86/percpu, to resolve conflicts and refresh the branch

Conflicts:
arch/x86/include/asm/percpu.h
arch/x86/include/asm/text-patching.h

Signed-off-by: Ingo Molnar <mingo@kernel.org>

show more ...

Merge tag 'drm-misc-next-2024-02-08' into msm-next

Merge the drm-misc tree to uprev MSM CI.

Signed-off-by: Rob Clark <robdclark@chromium.org>

clk: qcom: dispcc-*: switch to module_platform_driver

There is no need to register display clock controllers during subsys init
calls. Use module_platform_driver() instead.

Signed-off-by: Dmitry Ba

clk: qcom: dispcc-*: switch to module_platform_driver

There is no need to register display clock controllers during subsys init
calls. Use module_platform_driver() instead.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240206-clk-module-platform-driver-v1-2-db799bd2feeb@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

show more ...

Merge drm/drm-next into drm-misc-next

Kickstart 6.9 development cycle.

Signed-off-by: Maxime Ripard <mripard@kernel.org>

Merge branch 'linus' into x86/mm, to refresh the branch and pick up fixes

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge drm/drm-next into drm-xe-next

Sync to v6.8-rc1.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>

Merge v6.8-rc1 into drm-misc-fixes

Let's kickstart the 6.8 fix cycle.

Signed-off-by: Maxime Ripard <mripard@kernel.org>

Merge branch 'master' into mm-hotfixes-stable

Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux

Pull clk updates from Stephen Boyd:
"Only a couple new SoCs have support added this time, primarily for
Qualco

Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux

Pull clk updates from Stephen Boyd:
"Only a couple new SoCs have support added this time, primarily for
Qualcomm SM8650 based on the diffstat. Otherwise this is a collection
of non-critical fixes and cleanups to various clk drivers and their DT
bindings.

Nothing is changed in the core clk framework this time, although
there's a patch to fix a basic clk type initialization function. In
general, this pile looks to be on the smaller side.

New Drivers:
- Global, display, gpu, tcsr, and rpmh clocks on Qualcomm SM8650
- Mediatek MT7988 SoC clocks

Updates:
- Update Zynqmp driver for Versal NET platforms
- Add clk driver for Versal clocking wizard IP
- Support for stm32mp25 clks
- Add glitch free PLL setting support to si5351 clk driver
- Add DSI clocks on Amlogic g12/sm1
- Add CSI and ISP clocks on Amlogic g12/sm1
- Document bindings for i.MX93 ANATOP clock driver
- Free clk_node in i.MX SCU driver for resource with different owner
- Update the LVDS clocks to be compatible with i.MX SCU firmware 1.15
- Fix the name of the fvco in i.MX pll14xx by renaming it to fout
- Add EtherNet TSN and PCIe clocks on the Renesas R-Car V4H SoC
- Add interrupt controller and Ethernet clocks and resets on Renesas
RZ/G3S
- Check reset monitor registers on Renesas RZ/G2L-alike SoCs
- Reuse reset functionality in the Renesas RZ/G2L clock driver
- Global and RPMh clock support for the Qualcomm X1E80100 SoC
- Support for the Stromer APCS PLL found in Qualcomm IPQ5018
- Add a new type of branch clock, with support for controlling
separate memory control bits, to the Qualcomm clk driver
- Use above new branch type in Qualcomm ECPRI clk driver for QDU1000
and QRU1000
- Add a number of missing clocks related to CSI2 on Qualcomm MSM8939
- Add support for the camera clock controller on Qualcomm SC8280XP
- Correct PLL configuration in GPU and video clock controllers for
Qualcomm SM8150
- Add runtime PM support and a few missing resets to Qualcomm SM8150
video clock controller
- Fix configuration of various GCC GDSCs on Qualcomm SM8550
- Mark shared RCGs appropriately in the Qualcomm SM8550 GCC driver
- Fix up GPU and display clock controllers PLL configuration settings
on Qualcomm SM8550
- Cleanup variable init in Allwinner nkm module
- Convert various DT bindings to YAML
- A few kernel-doc fixes for Samsung SoC clock controllers"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (93 commits)
clk: mediatek: add drivers for MT7988 SoC
clk: mediatek: add pcw_chg_bit control for PLLs of MT7988
dt-bindings: clock: mediatek: add clock controllers of MT7988
dt-bindings: reset: mediatek: add MT7988 ethwarp reset IDs
dt-bindings: clock: mediatek: add MT7988 clock IDs
clk: mediatek: mt8188-topckgen: Refactor parents for top_dp/edp muxes
clk: mediatek: mt8195-topckgen: Refactor parents for top_dp/edp muxes
clk: mediatek: clk-mux: Support custom parent indices for muxes
dt-bindings: clock: sophgo: Add clock controller of CV1800 series SoC
clk: starfive: jh7100: Add CLK_SET_RATE_PARENT to gmac_tx
clk: starfive: Add flags argument to JH71X0__MUX macro
clk: imx: pll14xx: change naming of fvco to fout
clk: imx: clk-imx8qxp: fix LVDS bypass, pixel and phy clocks
clk: imx: scu: Fix memory leak in __imx_clk_gpr_scu()
clk: fixed-rate: fix clk_hw_register_fixed_rate_with_accuracy_parent_hw
clk: qcom: dispcc-sm8650: Add test_ctl parameters to PLL config
clk: qcom: gpucc-sm8650: Add test_ctl parameters to PLL config
clk: qcom: dispcc-sm8550: Use the correct PLL configuration function
clk: qcom: dispcc-sm8550: Update disp PLL settings
clk: qcom: gpucc-sm8550: Update GPU PLL settings
...

show more ...